IEI Technology IOVU-571N User Manual

IEI Technology Corp.

User Manual

IOVU-571N RISC-based Panel PC

IOVU-571N RISC-based Panel PC

MODEL:

IOVU-571N

RISC-based Panel PC with 5.7" Monitor and Touch Screen

Fast Ethernet, USB, RS-232/422/485

SD Card Slot, RoHS Compliant

Rev. 1.00 – 25 March, 2009

Page i

IOVU-571N RISC-based Panel PC

Revision

Date Version Changes

25 March, 2009 1.00 Initial release

Page ii

IOVU-571N RISC-based Panel PC

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

Copyright

reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

Page iii

IOVU-571N RISC-based Panel PC

Packing List

NOTE:

If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the IOVU-571N from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to

The items listed below should all be included in the IOVU-571N package.

 1 x IOVU-571N
 1 x Utility CD
 1 x Null modem cable
 1 x Touch screen pen
 1 x Screw kit

Optional items include

 Power adapter
 Wall mount
 Monitor arm
 Stand
 12 V DC 60 W power adapter with bare wire

[e-mail].

Page iv

Images of the above items are shown in Chapter 3.

IOVU-571N RISC-based Panel PC

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 OVERVIEW.................................................................................................................. 2

1.2 BENEFITS ................................................................................................................... 2

1.3 FEATURES................................................................................................................... 3

1.4 TECHNICAL SPECIFICATIONS ...................................................................................... 3

1.5 CERTIFICATIONS......................................................................................................... 4

2 DETAILED SPECIFICATIONS .................................................................................. 5

2.1 MECHANICAL OVERVIEW........................................................................................... 6

2.1.1 Front Panel........................................................................................................ 6

2.1.2 Connector Panel ................................................................................................ 6

2.2 INTERNAL OVERVIEW................................................................................................. 8

2.3 PHYSICAL DIMENSIONS.............................................................................................. 9

3 UNPACKING............................................................................................................... 10

3.1 ANTI-STATIC PRECAUTIONS.......................................................................................11

3.2 UNPACKING PRECAUTIONS........................................................................................11

3.3 PACKING CONTENTS................................................................................................. 12

3.4 OPTIONAL ITEMS...................................................................................................... 13

4 INSTALLATION ......................................................................................................... 14

4.1 INSTALLATION PRECAUTIONS ................................................................................... 15

4.2 PRE-INSTALLATION PREPARATION ............................................................................ 15

4.3 MOUNTING THE SYSTEM .......................................................................................... 15

4.3.1 Wall Mounting.................................................................................................. 16

4.3.2 Arm Mounting .................................................................................................. 18

4.3.3 Stand Mounting................................................................................................ 19

4.4 EXTERNAL CONNECTORS ......................................................................................... 20

4.4.1 LAN Connector ................................................................................................ 21

4.4.2 Power Terminal Block...................................................................................... 22

4.4.3 Serial Port Connector...................................................................................... 22

Page v

4.4.4 RS-422/485 Serial Port.................................................................................... 24

4.4.5 NAND/NOR Flash Boot and RS-422/485 Setup Switch................................... 24

4.4.6 USB Connector ................................................................................................ 25

4.5 SOFTWARE................................................................................................................ 26

A TERMINOLOGY........................................................................................................ 27

B HAZARDOUS MATERIALS DISCLOSURE ......................................................... 29

B.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CER TIFIED AS

ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ....................................... 30

IOVU-571N RISC-based Panel PC

Page vi

IOVU-571N RISC-based Panel PC

List of Figures

Figure 1-1: IOVU-571N....................................................................................................................2

Figure 2-1: Front Panel ..................................................................................................................6

Figure 2-2: IOVU-571N Connectors (Bottom Panel)....................................................................7

Figure 2-3: IOVU-571N Connectors (Right Side Panel)...............................................................7

Figure 2-4: IOVU-571N Physical Dimensions (millimeters)........................................................9

Figure 4-1: Wall-mounting Bracket.............................................................................................16

Figure 4-2: Chassis Support Screws..........................................................................................17

Figure 4-3: Secure the IOVU-571N..............................................................................................18

Figure 4-4: Arm Mount Retention Screw Holes.........................................................................19

Figure 4-5: Stand Mounting.........................................................................................................20

Figure 4-6: IOVU-571N External Connectors.............................................................................20

Figure 4-7: LAN Connection........................................................................................................21

Figure 4-8: Serial Device Connector...........................................................................................23

Figure 4-9: COM1 Pinout Locations............................................................................................23

Figure 4-10: DIP Switch................................................................................................................24

Figure 4-11: USB Connector........................................................................................................25

Page vii

IOVU-571N RISC-based Panel PC

List of Tables

Table 1-1: Technical Specifications..............................................................................................4

Table 3-1: Package List Contents...............................................................................................12

Table 3-2: Optional Item...............................................................................................................13

Table 4-1: LAN Pinouts ................................................................................................................21

Table 4-2: Power Terminal Block Pinouts..................................................................................22

Table 4-3: RS-232 Serial Port (COM 1) Pinouts .........................................................................23

Table 4-4: RS-422/485 Serial Port Pinouts .................................................................................24

Table 4-5: NAND/NOR and RS-422/485 Settings .......................................................................25

Table 4-6: USB Port Pinouts........................................................................................................26

Page viii

IOVU-571N RISC-based Panel PC

Chapter

1

1 Introduction

Page 1

1.1 Overview

Figure 1-1: IOVU-571N

IOVU-571N RISC-based Panel PC

The IOVU-571N is an RISC-based panel PC to a more complicated and larger system
beneath. The IOVU-571N provides rich input capabilities utilizing the touch screen. Output
capabilities are provided through RS-232/422/485 ports, network port and USB ports.

The IOVU-571N combines the reliability of a traditional HMI with the flexibility of a PC and
the small size of a thin-client. The IOVU-571N is preinstalled with Windows® CE .NET 5.0
operating system in a SD card, to provide rich application development and support
connectivity to network and I/O devices.

1.2 Benefits

Some of the IOVU-571N benefits include:

 Lower cost than an industrial PC.
 No hard disks and no fans remove the most vulnerable PC components.
 Standard peripheral connectors including Ethernet port, serial ports, USB

 Open architecture to run third party application software.

ports, SD memory, audio, and touch input.

Page 2

 Thin client device application in a remote terminal environment.
 Remote administration through network connections.

IOVU-571N RISC-based Panel PC

 Powered by popular open Windows® CE 5.0 embedded hard real-time

operating system provides rich Windows-based functions and application
software development support.

 Utilities and Remote Management Tools make it easy to manage centrally and

remotely.

1.3 Features

The IOVU-571N features are listed below:

 Embedded low power 200 MHz Nuvoton W90P910CBG proce s sor
 128 MB RAM
 256 MB CompactFlash® card
 One high performance 10/100 Mb/s Ethernet connector
 One USB 2.0 host port and one USB client port
 One RS-232 serial port and one RS-422/485 serial port
 5.7” TFT VGA display
 4-wire resistive touch panel
 9~28 V DC input
 Windows® CE 5.0 preinstalled in a SD card
 Built-in 2 W stereo speaker
 RoHS compliant

1.4 Technical Specifications

The IOVU-571N technical specifications are listed in Table 1-1.

Specification Value

System 200 MHz Nuvoton W90P910CBG processor

128 MB SDRAM
128 MB NAND flash
2 MB SPI flash

Battery backup RTC
Watchdog timer

AC’97 audio codec (built-in 2 W stereo speaker)

Page 3

Specification Value

Display TFT LCD

5.7”
640 x 480 resolution
400 cd/m2
4-wire resistive touch screen

IOVU-571N RISC-based Panel PC

I/O and
Communications

Power 9-28 V DC input by power jack and terminal block

Table 1-1: Technical Specifications

1.5 Certifications

All IOVU-571N series models comply with the following international standards:

 RoHS

For a more detailed description of these standards, please refer to the appendices

1 x 10/100 Mb/s network port
1 x RS-232
1 x RS-422/485
1 x USB type A port

1 x USB mini-B port
1 x SD slot

power switch and power LED

Page 4

IOVU-571N RISC-based Panel PC

Chapter

2

2 Detailed Specifications

Page 5

2.1 Mechanical Overview

2.1.1 Front Panel

The IOVU-571N front panel (Figure 2-1) comprises a 5.7” touch screen LCD in an
ABS/PC frame.

IOVU-571N RISC-based Panel PC

Figure 2-1: Front Panel

2.1.2 Connector Panel

All external peripheral interface connectors are located on the right side panel and the
bottom panel of the system enclosure. The peripheral interface connectors of the
IOVU-571N are shown in

Figure 2-2 and Figure 2-3.

Page 6

IOVU-571N RISC-based Panel PC

Figure 2-2: IOVU-571N Connectors (Bottom Panel)

Figure 2-3: IOVU-571N Connectors (Right Side Panel)

External peripheral interface connectors on the IOVU-571N include:

 1 x Power jack
 1 x Power terminal block
 1 x RS-232 connector

Page 7

 1 x RS-422/485 connector
 1 x RJ-45 Ethernet connector
 1 x Power switch
 1 x USB type A connector (right side panel)
 1 x USB mini-B connector (right side panel)
 1 x SD slot (right side panel)

2.2 Internal Overview

Internally the IOVU-571N contains a motherboard, connected to the external interface
connectors. The motherboard is also connected to the LCD panel and touch screen. For
full motherboard specifications and details, please refer to the motherboard user manual.

IOVU-571N RISC-based Panel PC

Page 8

IOVU-571N RISC-based Panel PC

2.3 Physical Dimensions

The physical dimensions of the IOVU-571N are shown in Figure 2-4 and listed below:

 Width: 180.00 mm
 Height: 132.00 mm
 Depth: 40.00 mm

Figure 2-4: IOVU-571N Physical Dimensions (millimeters)

Page 9

IOVU-571N RISC-based Panel PC

Chapter

3

3 Unpacking

Page 10

IOVU-571N RISC-based Panel PC

3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the
IOVU-571N may result in permanent damage to the IOVU-571N and
severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IOVU-571N. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the IOVU-571N, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple an ti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the IOVU-571N, place it on an

antic-static pad. This reduces the possibility of ESD damaging the
IOVU-571N.

 Only handle the edges of the PCB: When handling the PCB, hold the PCB

by the edges.

3.2 Unpacking Precautions

When the IOVU-571N is unpacked, please do the following:

 Follow the anti-static precautions outlined in Section
 Make sure the packing box is facing upwards so the IOVU-571N does not fall

out of the box.

 Make sure all the items listed below are included.

3.1.

Page 11

3.3 Packing Contents

NOTE:

If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the IOVU-571N from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [e-mail].

The IOVU-571N is shipped with the following components:

Quantity Item and Part Number Image

IOVU-571N RISC-based Panel PC

1 IOVU-571N

1 Utility CD including SDK, utilities, and

technical documentation

1 Null modem cable

1 Touch pen

1 Screw kit

Page 12

Table 3-1: Package List Contents

IOVU-571N RISC-based Panel PC

3.4 Optional Items

The following optional items are available.

Quantity Item and Part Number Image

1 Power adapter

(P/N: 63000-PSP0601AD101CT60-RS)

Table 3-2: Optional Item

Page 13

IOVU-571N RISC-based Panel PC

Chapter

4

4 Installation

Page 14

IOVU-571N RISC-based Panel PC

4.1 Installation Precautions

When installing the IOVU-571N, please follow the precautions listed below:

 Read the user manual: The user manual provides a complete description of

the IOVU-571N, installation instructions and configuration options.

 DANGER! Disconnect Power: Power to the IOVU-571N must be

disconnected during the installation pro cess, or before any attempt is m ade to
access the rear panel. Electric shock and personal injury might occur if the
rear panel of the IOVU-571N is opened while the power cord is still conne cted
to an electrical outlet.

 Qualified Personnel: The IOVU-571N must be instal led and operat ed only by

trained and qualified personnel. Maintenance, upgrades, or repairs may only
be carried out by qualified personnel who are familiar with the associated
dangers.

 Grounding: The IOVU-571N should be properly grounded. The volt age feeds

must not be overloaded. Adjust the cabling and provide external overcharge
protection per the electrical values indicated on the label attached to the back
of the IOVU-571N.

4.2 Pre-installation Preparation

Before installing the IOVU-571N, make sure the following tools are on hand:

 Philips (crosshead) screwdriver: All the retention screws on the system are

Philips screws.

4.3 Mounting the System

WARNING!

When mounting the IOVU-571N flat panel PC onto an arm, onto the
wall or onto a panel, it is better to have more than one person to help
with the installation to make sure the IOVU-571N does not fall down
and get damaged.

Page 15

The four methods of mounting the IOVU-571N are:

 Wall mounting
 Arm mounting
 Stand mounting

The four mounting methods are fully described below.

4.3.1 Wall Mounting

To mount the IOVU-571N flat panel PC onto a wall, please follow the steps belo w.

Step 1: Select the location on the wall for the wall-mounting bracket.

Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.

Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention

IOVU-571N RISC-based Panel PC

screws.

Step 4: Align the wall-mounting bracket screw holes with the pilot holes.

Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into

the four pilot holes and tightening them (

Figure 4-1).

Page 16

Figure 4-1: Wall-mounting Bracket

IOVU-571N RISC-based Panel PC

Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the

four screw holes on the real panel of the IOVU-571N and tighten until the screw
shank is secured against the rear panel (

Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on

the bracket.

Step 8: Carefully insert the screws through the holes and gently pull the monitor

downwards until the monitor rests securely in the slotted holes (
Ensure that all four of the mounting screws fit snuggly into their respective
slotted holes.

Figure 4-2).

Figure 4-2).

NOTE:

In the diagram below the bracket is already installed on the wall.

Figure 4-2: Chassis Support Screws

Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting

bracket. (

Figure 4-3). Step 0:

Page 17

IOVU-571N RISC-based Panel PC

Figure 4-3: Secure the IOVU-571N

4.3.2 Arm Mounting

The IOVU-571N is VESA (Video Electronics Standards Association) compliant and can be
mounted on an arm with a 75 mm interface pad. To mount the IOVU-571N on an arm,
please follow the steps below.

Step 1: The arm is a separately purchased item. Please correctly mount the arm onto

the surface it uses as a base. To do this, refer to the installation documentation
that came with the mounting arm.

NOTE:

Page 18

When purchasing the arm please ensure that it is VESA compliant and
that the arm has a 75 mm interface pad. If the mounting arm is not
VESA compliant it cannot be used to support the IOVU-571N.

IOVU-571N RISC-based Panel PC

Step 2: Once the mounting arm has been firmly attached to its surface, lift the

IOVU-571N onto the interface pad of the mounting arm.

Step 3: Align the retention screw holes on the mounting arm interface with those in the

IOVU-571N. The IOVU-571N arm mount retention screw holes are shown in

Figure 4-4.

Figure 4-4: Arm Mount Retention Screw Holes

Step 4: Secure the IOVU-571N to the interface pad by inserting four retention screws

through the mounting arm interface pad and into the IOVU-571N.

4.3.3 Stand Mounting

The IOVU-571N has Video Electronics Standards Association (VESA) standard mounting
holes tapped into the rear panel. The monitor stand mounting plate has a matching VESA
hole pattern. To mount the IOVU onto a stand, please follow the steps below.

Step 1: Line up the threaded holes on the monitor rear p anel with the screw hole s on the

monitor stand mounting plate.

Step 2: Secure the monitor to the stand with the supplied retention screws (

Step 0:

Figure 4-5).

Page 19

Figure 4-5: Stand Mounting

IOVU-571N RISC-based Panel PC

4.4 External Connectors

Figure 4-6 shows the bottom panel. The bottom panel consists of one RJ-45 Ethernet

connector, two serial ports, and two power connectors.

Page 20

Figure 4-6: IOVU-571N External Connectors

IOVU-571N RISC-based Panel PC

4.4.1 LAN Connector

CN Label: LAN1
CN Type:
CN Location:
CN Pinouts:

The LAN ports support 10 Mb/s (Ethernet) and 100 Mb/s (Fast Ethernet) transfer rates. To
plug in an Ethernet cable, refer to

RJ-45
See Figure 4-6
See Table 4-1

Figure 4-7 below.

Figure 4-7: LAN Connection

PIN DESCRIPTION PIN DESCRIPTION

1 TX+ 5 +3.3V
2 TX- 6 LAN_GND
3 RX+ 7 LAN_GND
4 RX- 8 LAN_GND

Table 4-1: LAN Pinouts

Page 21

4.4.2 Power Terminal Block

CN Label: TERMINAL

IOVU-571N RISC-based Panel PC

CN Type:
CN Location:
CN Pinouts:

A single power terminal block can be connected to a 9 VDC to 28 VDC power source.

PIN DESCRIPTION

1 DC9 V ~ DC28 V
2 Ground

Table 4-2: Power Terminal Block Pinouts

2-pin terminal block
See Figure 4-6
See Table 4-2

4.4.3 Serial Port Connector

CN Label: COM1
CN Type:
CN Location:

DB-9 connector
See Figure 4-6

Page 22

CN Pinouts:

The 9-pin DB-9 COM 1 serial port connector is connected to RS-232 serial
communications devices. To plug in the serial port plug refer to the diagram in
below.

See Table 4-3 and Figure 4-9

Figure 4-8

IOVU-571N RISC-based Panel PC

Figure 4-8: Serial Device Connector

The pinouts for the serial port are shown below.

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND

Table 4-3: RS-232 Serial Port (COM 1) Pinouts

Figure 4-9: COM1 Pinout Locations

Page 23

4.4.4 RS-422/485 Serial Port

CN Label: COM2

IOVU-571N RISC-based Panel PC

CN Type:
CN Location:
CN Pinouts:

There is one serial port on the bottom panel that can be configured as either RS-422 or
RS-485 serial port.

Pin No. Description

1 TDX485#_R
2 TDX485+_R
3 TDX485+_R
4 TDX485#_R

Table 4-4: RS-422/485 Serial Port Pinouts

DB-9
See Figure 4-6
See Table 4-4

4.4.5 NAND/NOR Flash Boot and RS-422/485 Setup Switch

CN Label: SW2
CN Type:
CN Location:
CN Pinouts:

The IOVU-571N has one DIP switch on the bottom panel. The switch configures the
NAND or NOR flash boot and select COM2 function mode.

Figure 4-10: DIP Switch

The settings for the DIP switch are shown below.

DIP switch
See Figure 4-10
See Table 4-5

Page 24

IOVU-571N RISC-based Panel PC

. 1 2 3 4 5 6

NAND

NOR

RS-422

RS-485

Table 4-5: NAND/NOR and RS-422/485 Settings

4.4.6 USB Connector

CN Label: USB1
CN Type:
CN Location:
CN Pinouts:

USB port
See Figure 4-6
See Table 4-6

The IOVU-571N has one external USB 2.0 type A port on the right side panel. The port
connects to both USB 2.0 and USB 1.1 devices. To install a USB device, refer to

Figure 4-11 below.

Figure 4-11: USB Connector

Page 25

Pinouts for the USB port are shown below.

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 VCC 5 VCC
2 D1- 6 D2­3 D1+ 7 D2+
4 GND 8 GND

Table 4-6: USB Port Pinouts

4.5 Software

The IOVU-571N has Windows CE 5.0 pre-installed. For information about configuring the
operating system, adding remote management tools or additional software and drivers,
refer to the user manuals on IEI IOVU Utility CD that came with the IOVU-571N.

IOVU-571N RISC-based Panel PC

Page 26

IOVU-571N RISC-based Panel PC

Appendix

A

A Terminology

Page 27

IOVU-571N RISC-based Panel PC

AC ’97

CompactFlash®

CMOS

COM

DIO

LCD

Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®
in 1997.

CompactFlash® is a solid-state storage device. CompactFlash® d evices
use flash memory in a standard size enclosure. Type II is thicker than
Type I, but a Type II slot can support both types.

Complimentary metal-oxide-conductor is an integrated circuit used in
chips like static RAM and microprocessors.

COM refers to serial ports. Serial ports offer serial communication to
expansion devices. The serial port on a person al computer is usually a
male DB-9 connector.

The digital inputs and digital outputs are general control signals that
control the on/off circuit of external devices or TTL devices. Data can be
read or written to the selected address to enable the DIO functions.

Liquid crystal display (LCD) is a flat, low-power display device that
consists of two polarizing plates with a liquid crystal panel in between.

LVDS

POST

RAM

UHCI

USB

VGA

Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.

The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.

Random Access Memory (RAM) is volatile memory that loses data when
power is lost. RAM has very fast data transfer rates compared to other
storage like hard drives.

The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.

The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12 Mb/s dat a transfer rates and
USB 2.0 supports 480 Mb/s data transfer rates.

The Video Graphics Array (VGA) is a graphics display system developed
by IBM.

Page 28

IOVU-571N RISC-based Panel PC

B Hazardous Materials

Appendix

B

Disclosure

Page 29

IOVU-571N RISC-based Panel PC

B.1 Hazardous Materials Disclosure Table for IPB Products

Certified as RoHS Compliant Under 2002/95/EC Without
Mercury

The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is appli cable to China
RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.

Please refer to the table on the next page.

Page 30

IOVU-571N RISC-based Panel PC

Toxic or Hazardous Substances and Elements Part Name

Housing
Display
Printed Circuit

Board
Metal

Fasteners
Cable

Assembly
Fan Assembly
Power Supply

Assemblies

Lead
(Pb)

X O O O O X
X O O O O X
X O O O O X

X O O O O O

X O O O O X

X O O O O X
X O O O O X

Mercury
(Hg)

Cadmium
(Cd)

Hexavalent
Chromium
(CR(VI))

Polybrominated
Biphenyls
(PBB)

Polybrominated
Diphenyl
Ethers
(PBDE)

Battery

O: This toxic or hazardous substance is containe d in all of the homog eneous mate rials for the p a rt is
below the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for
this part is above the limit requirement in SJ/T11363-2006

O O O O O O

Page 31

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些

元件将会单独标示出来。

IOVU-571N RISC-based Panel PC

部件名称

壳体
显示
印刷电路板
金属螺帽
电缆组装
风扇组装
电力供应组装
电池

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

有毒有害物质或元素
铅

(Pb)

X O O O O X
X O O O O X
X O O O O X
X O O O O O
X O O O O X
X O O O O X
X O O O O X
O O O O O O

汞
(Hg)

镉
(Cd)

六价铬
(CR(VI))

多溴联苯
(PBB)

多溴二苯
醚

(PBDE)

Page 32