IEI Technology IOVU-210AR-RK39 User Manual

IOVU-210AR-RK39 Panel PC

Page i

10.1" RISC-Based Panel PC with P-CAP Touchscreen,

MODEL:

IOVU-210AR-RK39

Rev. 1.00 – November 8, 2018

Rockchip RK3399 On-board SoC, Wi-Fi, Bluetooth, Came r a,

USB, SOS Key, GbE with PoE, Android 7.1, RoHS Compliant

User Manual

IOVU-210AR-RK39 Panel PC

Page ii

Date Version Changes

November 8, 2018 1.00 Initial release

Revision

IOVU-210AR-RK39 Panel PC

Page iii

Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibil ity of such damages.

This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

IOVU-210AR-RK39 Panel PC

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.

CAUTION

Cautionary messages should be heeded to help red uce the chance of
losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.

IOVU-210AR-RK39 Panel PC

Page v

Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1 OVERVIEW .................................................................................................................. 2

1.2 FEATURES ................................................................................................................... 2

1.3 FRONT PANEL ............................................................................................................. 3

1.4 REAR PANEL ............................................................................................................... 4

1.5 SYSTEM SPECIFICATIONS ............................................................................................ 5

1.6 DIMENSIONS ............................................................................................................... 7

2 UNPACKING ................................................................................................................. 8

2.1 PACKING LIST ............................................................................................................. 9

2.2 OPTIONAL ITEM ........................................................................................................ 10

3 INSTALLATION .......................................................................................................... 11

3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 12

3.2 INSTALLATION PRECAUTIONS ................................................................................... 12

3.3 EXTERNAL I/O CONNECTORS ................................................................................... 13

3.3.1 Digital I/O Connectors .................................................................................... 13

3.3.2 Digital I/O Terminal Block .............................................................................. 13

3.3.3 I2C Connectors ................................................................................................. 14

3.3.4 microSD Card Slot ........................................................................................... 14

3.3.5 RJ-45 LAN Connectors .................................................................................... 15

3.3.5.1 LAN1 Connector with PoE ....................................................................... 15

3.3.5.2 LAN2 Connector ....................................................................................... 15

3.3.6 RS-232 Serial Interface .................................................................................... 16

3.3.7 RS-232/422/485 Serial Interface ...................................................................... 17

3.3.8 USB Connectors ............................................................................................... 17

3.4 MOUNTING THE SYSTEM .......................................................................................... 18

3.4.1 Wall Mounting .................................................................................................. 18

3.4.1.1 Wall Mount Bracket Dimensions .............................................................. 20

3.4.2 In-Wall Mounting ............................................................................................. 20

IOVU-210AR-RK39 Panel PC

Page vi

3.4.2.1 In-Wall Mounting Box Dimensions .......................................................... 23

3.5 POWER-ON PROCEDURE ........................................................................................... 24

3.6 AVAILABLE DRIVERS ................................................................................................ 25

3.6.1 Driver Download ............................................................................................. 25

3.7 SYSTEM MAINTENANCE ........................................................................................... 27

4 ANDROID OS .............................................................................................................. 28

4.1 HOME SCREEN ......................................................................................................... 29

4.1.1 Adding a Home Screen ..................................................................................... 29

4.1.2 Switching between Home Screens .................................................................... 30

4.1.3 Favorites Tray .................................................................................................. 30

4.1.4 Adding Shortcuts .............................................................................................. 31

4.1.5 Arranging the Home Screen ............................................................................. 33

4.2 NAVIGATION BUTTONS ............................................................................................. 34

4.3 STATUS BAR ............................................................................................................. 35

A REGULATORY COMPLIANCE .............................................................................. 37

B SAFETY PRECAUTIONS ......................................................................................... 42

B.1 SAFETY PRECAUTIONS ............................................................................................. 43

B.1.1 General Safety Precautions ............................................................................. 43

B.1.2 Anti-static Precautions .................................................................................... 44

B.1.3 Product Disposal ............................................................................................. 45

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 45

B.2.1 Maintenance and Cleaning .............................................................................. 45

B.2.2 Cleaning Tools ................................................................................................. 46

C HAZARDOUS MATERIALS DISCLOSURE ......................................................... 47

IOVU-210AR-RK39 Panel PC

Page vii

List of Figures

Figure 1-1: IOVU-210AR-RK39 Panel PC ...................................................................................... 2

Figure 1-2: Front Panel .................................................................................................................. 3

Figure 1-3: Rear Panel .................................................................................................................... 4

Figure 1-4: Dimensions (Unit: mm) ............................................................................................... 7

Figure 3-1: microSD Card Slot .................................................................................................... 14

Figure 3-2: LAN2 Connector ........................................................................................................ 16

Figure 3-3: USB Connectors ........................................................................................................ 17

Figure 3-4: Wall Mounting Bracket Installation ......................................................................... 18

Figure 3-5: Secure Mounting Screws ......................................................................................... 19

Figure 3-6: Mounting Panel PC ................................................................................................... 19

Figure 3-7: Wall Mount Bracket Dimensions (Unit: mm) .......................................................... 20

Figure 3-8: Drill Holes for Securing In-Wall Mounting Box ...................................................... 21

Figure 3-9: Secure Mounting Screws ......................................................................................... 22

Figure 3-10: Mounting Panel PC ................................................................................................. 22

Figure 3-11: In-Wall Mounting Box Dimensions (Unit: mm) ..................................................... 23

Figure 3-12: Power Input Jack ..................................................................................................... 24

Figure 3-13: IEI Resource Download Center .............................................................................. 25

Figure 4-1: Adding a Home Screen ............................................................................................. 29

Figure 4-2: Multiple Home Screens ............................................................................................. 30

Figure 4-3: Favorites Tray ............................................................................................................ 30

Figure 4-4: All Apps/WIDGETS Page .......................................................................................... 32

Figure 4-5: Trash an Item on Home Screen ............................................................................... 33

Figure 4-6: Navigation Buttons ................................................................................................... 34

Figure 4-7: Status Bar .................................................................................................................. 35

Figure 4-8: Notification List and System Status ........................................................................ 36

IOVU-210AR-RK39 Panel PC

Page viii

List of Tables

Table 1-1: Technical Specifications .............................................................................................. 6

Table 2-1: Packing List ................................................................................................................. 10

Table 2-2: Optional Item ............................................................................................................... 10

Table 3-1: DIO Connector (DIO2, DIO3) Pinouts ........................................................................ 13

Table 3-2: DIO Terminal Block (DIO1) Pinouts .......................................................................... 13

Table 3-3: I2C Connector (I2C) Pinouts ....................................................................................... 14

Table 3-4: LAN1 Connector Pinouts ........................................................................................... 15

Table 3-5: LAN2 Connector Pinouts ........................................................................................... 15

Table 3-6: LAN2 Ethernet Connector LEDs ............................................................................... 16

Table 3-7: RS-232 Connector (UART2) Pinouts ......................................................................... 16

Table 3-8: RS-232/422/485 Terminal Block (UART1) Pinouts ................................................... 17

Table 4-1: Navigation Buttons ..................................................................................................... 34

IOVU-210AR-RK39 Panel PC

Page 1

Chapter

1

1 Introduction

IOVU-210AR-RK39 Panel PC

Page 2

1.1 Overview

Figure 1-1: IOVU-210AR-RK39 Panel PC

The IOVU-210AR-RK39 is a 10.1" RISC-based panel PC with Android 7.1 OS. At the
heart of the system is the Rockchip RK3399 on-board SoC, offering low power in a
powerful package. The IOVU-210AR-RK39 provides rich input capabilities utilizing the
projected capacitive touchscreen. Other peripherals include RFID reader, digital I/O, one
USB 2.0 port, one USB 3.0 port, one RS-232 p ort, on e RS-232/42 2/485 po rt and one GbE
LAN port with PoE support.

1.2 Features

The IOVU-210AR-RK39 features the following:

 Fanless design
 Rockchip RK3399 on-board SoC
 On-board 1866 MHz 2 GB LPDDR3 memory
 16 GB eMMC NAND flash
 Projected capacitive touchscreen
 Equips with Wi-Fi 802.11a/b/g/n/ac and Bluetooth v4.1
 SOS button for calling help in emergency
 Volume up and volume down keys
 4-bit and 2-bit digital I/O

IOVU-210AR-RK39 Panel PC

Page 3

 Three I2C sensor connectors via Grove connectors
 One RS-232/422/485 port and one RS-232 port
 Two GbE ports, one with PoE support
 One USB 3.0 port and one USB 2.0 port
 Android 7.1 OS pre-installed
 RoHS compliant

1.3 Front Panel

The front panel of the IOVU-210AR-RK39 contains a 10.1" LCD with projected capacitive
touchscreen, 5-megapixel camera, an SOS key, two volume keys, a power indicator and
an RFID indicator.

Figure 1-2: Front Panel

The states of the LED indicators located on the front panel are listed below.

Power LED

RFID LED

Off The system is turned off.
Green The system is turned on.
Off RFID reader is off
Green RFID reader is on

IOVU-210AR-RK39 Panel PC

Page 4

in and PoE are connected to the device, the connection

1.4 Rear Panel

The rear panel contains several I/O interfaces as shown below. The detailed information
of each connector is listed in Section 3.3.

Figure 1-3: Rear Panel

NOTE:

When both DC­with higher voltage will be the main power source.

IOVU-210AR-RK39 Panel PC

Page 5

1.5 System Specifications

The IOVU-210AR-RK39 technical specifications are listed below.

System
CPU Rockchip RK3399 on-board SoC

Memory 2 GB 1866 MHz LPDDR3L on-board memory
Storage 16 GB eMMC NAND flash

Audio 2 x Speaker (1.5 W)

Camera 5-megapixel fr o n t-facing camera
Thermal Solution Fanless
Watchdog Timer Yes
Real-time Clock Battery backup RTC
OS Android 7.1
Display
LCD Size 10.1"
Max. Resolution 800 x 1280

(dual-core Cortex-A72 + quad-core Cortex-A53, 64-bit)

One microSD card slot (rear panel)

1 x Digital microphone

Brightness (cd/m2) 250 (typ.)
Contrast Ratio 800:1 (typ.)
Pixel Pitch (mm) 0.0564 (H) x 0.1692 (V)
Viewing Angle 85/85/85/85 degree
Touchscreen Projected capacitive touchscreen
Communication
Wireless LAN 802.11a/b/g/n/ac
Bluetooth Bluetooth v4.1
RFID 13.56 MHz ISO4443 A/B, read-write capable,

ISO 14443A (MIFARE), ISO 14443B (FeliCa)

Power
Power Input 9 V ~ 30 V DC

DC input: φ2.5/5.5mm DC jack
PoE: IEEE 802.3 at standard (power device)

IOVU-210AR-RK39 Panel PC

Page 6

Physical Character
Construction Material PC+ABS plastic
Color White
Mounting Wall mounting, in-wall mounting
Dimensions (W x H x D) 282.5 mm x 176.4 mm x 26.8 mm
Operation Temperature -10°C ~ 50°C (14°F ~ 122°F) with air flow
Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)
Humidity 10% ~ 95%, non-condensing
Weight (Net) 0.85 kg
Certifications CE, FCC Class B
Connectors, Buttons and Indicators
External I/O 1 x USB 3.0 Type-A port

1 x USB 2.0 Type-A port
1 x RJ-45 GbE port with PoE (by RTL8211E)
1 x RJ-45 GbE port (by RTL8211E)
1 x RS-232/422/485 port via 4-pin terminal block (COM1)
1 x RS-232 port via Grove connector (COM2)
1 x Digital I/O via 6-pin terminal block (4-bit, 2 in + 2 out)
2 x Digital I/O via Grove connector (2-bit, 1 in + 1 out)
3 x I2C sensor connector via Grove connector

Internal I/O 2 x UART pin header with 3 V

2 x USB 2.0 pin header

Button 1 x Reset button

2 x Volume key (up, down)
1 x SOS key

LED Indicators 1 x Power

1 x RFID

Table 1-1: Technical Specifications

IOVU-210AR-RK39 Panel PC

Page 7

1.6 Dimensions

The dimensions of the IOVU-210AR-RK39 are shown below.

Figure 1-4: Dimensions (Unit: mm)

IOVU-210AR-RK39 Panel PC

Page 8

Chapter

2

2 Unpacking

IOVU-210AR-RK39 Panel PC

Page 9

has been

properly installed. This ensures the screen is protected during the

was purchased from or contact an IEI sales

To unpack the panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the system

installation process.

Step 1: Carefully cut the tape sealing the box . Only cut deep enough to break the tape.

Step 2: Open the box.

Step 3: Lift the IOVU-210AR-RK39 out of the box.

Step 4: Make sure all the components listed i n the packing list are present. Step 0:

2.1 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
IOVU-210AR-RK39
representative directly by sending an email to [e-mail].

The IOVU-210AR-RK39 is shipped with the following components:

Quantity Item Image

1 IOVU-210AR-RK39 panel PC

IOVU-210AR-RK39 Panel PC

Page 10

Quantity Item Image

1 Wall mo unt bracket

4 M4*6 screw for wall mounting

2 M2.5*4 screw for wall mounting

1 4-pin terminal block

1 6-pin terminal block

Table 2-1: Packing List

2.2 Optional Item

The following is optional component which may be separately purchased:

Item Image

90V~264V AC input, 12V/60W DC power adapter
(P/N: 63040-010060-120-RS)

In-wall mounting box
(P/N: 41320-0490E4-00-RS)

Table 2-2: Optional Item

IOVU-210AR-RK39 Panel PC

Page 11

Chapter

3

3 Installation

IOVU-210AR-RK39 Panel PC

Page 12

Failure to take ESD precautions during the maintenance of the

may result in permanent damage to the

3.1 Anti-static Precautions

WARNING:

IOVU-210AR-RK39
IOVU-210AR-RK39 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IOVU-210AR-RK39. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the IOVU-210AR-RK39 is accessed internally, or any
other electrical component is handled, the following anti-static precautions are strictly
adhered to.

 Wear an anti-static wristband: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: - Before handling the board touch a ny grounded conducting

material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.

 Use an anti-static pad: - When configuring the IOVU-210AR-RK39, place it on

an anti-static pad. Thi s reduce s the possib ility of ESD da maging th e
IOVU-210AR-RK39.

 Only handle the edges of the PCB: - When handling the PCB, hold the PCB

by the edges.

3.2 Installation Precautions

When installing the flat panel PC, please follow the precautions listed below:

 Power turned off: When installing the flat panel PC, make sure the power is

off. Failing to turn of f the power may cause severe injury to the body and/or
damage to the system.

 Certified Engineers: Only certified engineers should install and modify

onboard functionalities.

IOVU-210AR-RK39 Panel PC

Page 13

 Anti-static Discharge: If a user open the rear panel of the flat panel PC, to

configure the jumpers or plug in added peripheral dev ices, ground themsel ves
first and wear and anti-static wristband.

3.3 External I/O Connectors

This section provides an overview of the external I/O connectors of the
IOVU-210AR-RK39.

3.3.1 Digital I/O Connectors

The IOVU-210AR-RK39 has two digital I/O connectors in Grove int erfac e. T he pi nout s ar e
shown below.

Pin Description
1 GND
2 DIO_3V3

3 DIO_D5/D7
4 DIO_D6/D8

Table 3-1: DIO Connector (DIO2, DIO3) Pinouts

3.3.2 Digital I/O Terminal Block

The IOVU-210AR-RK39 has one 6-pin digital I/O terminal block. The pinouts are shown
below.

Pin Description
1 VIO_3V3 (DIO1)

2 VIO_3V3 (DIO2)
3 GND
4 VIO_3V3 (DIO3)
5 VIO_3V3 (DIO4)
6 GND

Table 3-2: DIO Terminal Block (DIO1) Pinouts

IOVU-210AR-RK39 Panel PC

Page 14

3.3.3 I2C Connectors

The IOVU-210AR-RK39 has three I2C connectors in Grove interface. The pinouts are
shown below.

Pin Description
1 GND
2 IOT_3V3

3 SDA1_3V3
4 SCL1_3V3

Table 3-3: I2C Connector (I2C) Pinouts

3.3.4 microSD Card Slot

The system comes with a push-push microSD card slot for installation of a microSD card.

Figure 3-1: microSD Card Slot

IOVU-210AR-RK39 Panel PC

Page 15

3.3.5 RJ-45 LAN Connectors

There are two RJ-45 LAN connectors that allow connection to external network, and the
LAN1 connector also supports PoE function.

3.3.5.1 LAN1 Connector with PoE

The LAN1 connector enables connection to an external network and supports PoE. The
LAN1 connector pinouts are shown below.

Pin Description
1 LAN1_MDX0+
2 LAN1_MDX0-

3 LAN1_MDX1+
4 LAN1_MDIX2+
5 LAN1_MDX2­6 LAN1_MDX1­7 LAN1_MDIX3+
8 LAN1_MDX3-

Table 3-4: LAN1 Connector Pinouts

3.3.5.2 LAN2 Connector

The LAN2 connector pinouts are shown below.

Pin Description
1 LAN1_MD0+
2 LAN1_MD0-

3 LAN1_MD1+
4 LAN1_MD1­5 LAN1_MD2+
6 LAN1_MD2­7 LAN1_MD3+
8 LAN1_MD3-

Table 3-5: LAN2 Connector Pinouts

IOVU-210AR-RK39 Panel PC

Page 16

The LAN2 connector has two status LEDs, one orange and one green. The orange LED
indicates the port speed and the green LED indicates activity on the port (Table 3-6).

Figure 3-2: LAN2 Connector

SPEED LED LINK LED
Status Description Status Description

Green 10/100 Mbps Green On: Linked
Orange 1000 Mbps

Table 3-6: LAN2 Ethernet Connector LEDs

3.3.6 RS-232 Serial Interface

The IOVU-210AR-RK39 has one RS-232 connector in Grove interface. The pinouts are
shown below.

Pin Description
1 GND
2 VIO_3V3

3 RS232_TXD1
4 RS232_RXD1

Table 3-7: RS-232 Connector (UART2) Pinouts

Flashing: Activity

IOVU-210AR-RK39 Panel PC

Page 17

3.3.7 RS-232/422/485 Serial Interface

The system has a 4-pin RS-232/422/485 t erminal block. It s pi nouts are shown below.

Pin RS-232 RS-422 RS-485

1 N/A TX- DATA­2 TXD TX+ DATA+
3 RXD RX+ N/A
4 N/A RX- N/A

Table 3-8: RS-232/422/485 Terminal Block (UART1) Pinouts

3.3.8 USB Connectors

The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices.

Figure 3-3: USB Connectors

IOVU-210AR-RK39 Panel PC

Page 18

the replacement screw should be not

3.4 Mounting the System

3.4.1 Wall Mounting

To mount the IOVU-210AR-RK39 onto a wall, please follow the steps below.

Step 1: Select a location on the wall for the wall-mounting bracket. Carefully mark the

locations of the screw holes of the wall mounting bracket on the mounting area.
Drill the pilot holes at the marked locations (Figure 3-4

Step 2: Secure the mounting bracket t o the wall by inserting the retention screws into

the four pilot holes and tightening them (Figure 3-4

Figure 3-4: Wall Mounting Bracket Installation

Step 3: Insert the four mounting screws (M4*6) came with the panel PC into the four

screw holes on the mounting bracket and tighten until the screw shank is

).

).

secured (Figure 3-5).

CAUTION:

Please use the M4 screws provided in
the package for the mounting screws. If
the screw is missing, the thread depth of

more than 4 mm.

IOVU-210AR-RK39 Panel PC

Page 19

Figure 3-5: Secure Mounting Screws

Step 4: Align the mounting holes on the rear of the panel PC with the mounting screws.

Step 5: Carefully attach the panel PC to the mounting screws and gently pull the panel

PC downwards until the panel PC rests securely on screws. Ensure that all four
of the slotted holes fit snuggly into their resp ect i ve mounting screws

(Figure 3-6

Step 6: Secure the panel PC by inst alling th e two rete ntion screws (M3*4) came with the

panel PC into the screw hole on the bottom of the bracket (Figure 3-6

).

).

Figure 3-6: Mounting Panel PC

IOVU-210AR-RK39 Panel PC

Page 20

3.4.1.1 Wall Mount Bracket Dimensions

The dimensions of the wall mount bracket shipped with the system are shown below.

Figure 3-7: Wall Mount Bracket Dimensions (Unit: mm)

3.4.2 In-Wall Mounting

To mount the IOVU-210AR-RK39 into a wall using the optional in-wall mounting box,
please follow the steps below.

Step 1: When constructing the building, l eave a section from the wall that corresponds

to the dimensions of the in-wall mounting box.

Step 2: Carefully mark the locations of the screw holes of the in-wall mounting box on

the mounting area. Drill the pilot holes at t he m ark ed locations. (Figure 3-8).

IOVU-210AR-RK39 Panel PC

Page 21

the replacement screw should be not

Figure 3-8: Drill Holes for Securing In-Wall Mounting Box

Step 3: Secure the mounting bracket t o the in-wall mounting box by inserting the

retention screws into the four pilot holes and t ightening them (Figure 3-9

Step 4: Insert the four mounting screws (M4*6) came with the panel PC into t he four

screw holes on the mounting bracket and tighten until the screw shank is
secured (Figure 3-9

).

).

CAUTION:

Please use the M4 screws provided in
the package for the mounting screws. If
the screw is missing, the thread depth of

more than 4 mm.

Step 5: Slide the in-wall mounting box i nto the wall. Secure the box to the wall with

retention screws (Figure 3-9

).

IOVU-210AR-RK39 Panel PC

Page 22

Figure 3-9: Secure Mounting Screws

Step 6: Align the mounting holes on the rear of the panel PC with the bracket mounting

screws.

Step 7: Carefully attach the panel PC to the mounting screws and gently pull the panel

PC downwards until the panel PC rests securely on screws. Ensure that all four
of the slotted holes fit snuggly into their resp ect i ve mounting screws

(Figure 3-10

Step 8: Secure the panel PC by installing t he two screws (M3*4) came with the panel

PC into the two screw holes on the bottom of the bracket. (Figure 3-10

).

).

Figure 3-10: Mounting Panel PC

IOVU-210AR-RK39 Panel PC

Page 23

3.4.2.1 In-Wall Mounting Box Dimensions

The dimensions of the optional in-wall mounting box are shown below.

Figure 3-11: In-Wall Mounting Box Dimensions (Unit: mm)

IOVU-210AR-RK39 Panel PC

Page 24

Make sure a power supply with the correct input voltage is being fed into

3.5 Power-On Procedure

WARNING:

the system. Incorrect voltages applie d to the system may cause damage to
the internal electronic components and may also cause injury to the user.

The IOVU-210AR-RK39 supports 9 V ~ 30 V DC power input. To power-on, connect the
IOVU-210AR-RK39 power input jack to a power source. Once connected, the system will
automatically turn on and the power LED on the front panel will light up in green.

Figure 3-12: Power Input Jack

IOVU-210AR-RK39 Panel PC

Page 25

Figure 3-13: IEI Resource Download Center

3.6 Available Drivers

All the drivers for the IOVU-210AR-RK39 are available on IEI Resource Download Center
(https://download.ieiworld.com
relevant software, utilities, and documentation.

3.6.1 Driver Download

). Type IOVU-210AR-RK39 and press Enter to find all the

To download drivers from IEI Resource Download Center, follow the steps below.

Step 1: Go to https://download.ieiworld.com

Step 2: All product-related software, utilities, and documentation will be listed. You can

choose Driver to filter the result.

. Type IOVU-210AR-RK39 and press Enter.

IOVU-210AR-RK39 Panel PC

Page 26

Step 3: Click the driver file name on the page and you will be prompted with the

following window. Yo u can download the entire ISO file (
arrow to find an individual driver and click the file name to download (

), or click the small

).

IOVU-210AR-RK39 Panel PC

Page 27

lease contact the system

3.7 System Maintenance

If the components of the IOVU-210AR-RK39 fail, they must be replaced. Please contact
the system reseller or vendor to purchase the replacement parts.

NOTE:

A user cannot replace a motherboard. If the motherboard fails it must
be shipped back to IEI to be replaced. P
vendor, reseller or an IEI sales person directly.

IOVU-210AR-RK39 Panel PC

Page 28

Chapter

4

4 Android OS

IOVU-210AR-RK39 Panel PC

Page 29

The IOVU-210AR-RK39 comes with Android OS pre-i nstalle d. This chapt er intro duces the
user interface and basic functions of Android OS installed in the IOVU-210AR-RK39.

4.1 Home Screen

Android OS supports multiple home screens allowing users to customize the screen with
widgets, apps and shortcuts. The following sections describe the basic technique to
manage the home screen.

4.1.1 Adding a Home Screen

To add a home screen, touch and hold an app/widget icon. The following screen appears,
indicating that a new home screen is available. Drag and relea se the icon to the new home
screen.

Figure 4-1: Adding a Home Screen

IOVU-210AR-RK39 Panel PC

Page 30

4.1.2 Switching between Home Screens

Swipe right or left to switch between home screens.

Figure 4-2: Multiple Home Screens

4.1.3 Favorites Tray

The Favorites tray at the bottom of each home screen allows users to keep the most
important or frequently used shortcuts.

Figure 4-3: Favorites Tray

IOVU-210AR-RK39 Panel PC

Page 31

4.1.4 Adding Shortcuts

To add app or widget shortcuts on the home screen, follow the steps below.

Step 1: To add an app shortcut, tap the up arrow on the home screen to access the

All Apps page.

To add a widget shortcut, touch and hold the background of a home screen, then
tap WIDGETS.

IOVU-210AR-RK39 Panel PC

Page 32

Step 2: Touch and hold an app icon or a widget, and drag it t o the home screen.

Figure 4-4: All Apps/WIDGETS Page

IOVU-210AR-RK39 Panel PC

Page 33

4.1.5 Arranging the Home Screen

The items on the home screen can be moved and deleted. Touch and hold an item on the
home screen and drag it where you want. To trash the item on the screen, drag it to the
Remove icon. Release the icon when it turns gray.

Figure 4-5: Trash an Item on Home Screen

IOVU-210AR-RK39 Panel PC

Page 34

4.2 Navigation Buttons

The navigation buttons shown in Figure 4-8 can always be found at the bottom of every
screen.

Figure 4-6: Navigation Buttons

Buttons Description

Table 4-1: Navigation Buttons

Tap to turn the volume down.

Tap to return to the previous screen.

Tap to return to the home screen.

Tap to display all the recently used applications.

Tap to turn the volume up.

Tap to take a screensho t.

IOVU-210AR-RK39 Panel PC

Page 35

4.3 Status Bar

The status bar on the top of the screen (Figure 4-9) displays system status, such as
battery level or signal strength.

Figure 4-7: Status Bar

Swipe down from the status bar to view notification and status details (Figure 4-10).

IOVU-210AR-RK39 Panel PC

Page 36

Figure 4-8: Notification List and System Status

IOVU-210AR-RK39 Panel PC

Page 37

Appendix

A

A Regulatory Compliance

IOVU-210AR-RK39 Panel PC

Page 38

If the user modifies and/or install other devices in the equipment, the CE conformity

If this equipment has telecommunications functionality, it also complies with the

DECLARATIO N OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive 2014/30/EU
 Low-Voltage Directive 2014/35/EU
 RoHS II Directive 2011/65/EU

declaration may no longer apply.

requirements of the R&TTE Directive 1999/5/E C.

English
IEI Integration Corp declares that this equi pm ent is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Български [Bulgarian]
IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива 1999/5/ЕС.
Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]
IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen
und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

Eesti [Estonian]
IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

IOVU-210AR-RK39 Panel PC

Page 39

Español [Spanish]
IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicabl es o exigibles de la Directiva 1999/5/CE.
Ελληνική [Greek]
IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/ΕΚ.

Français [French]
IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]
IEI Integration Corp dichiara che questo appar ecchio è conforme ai requisiti essenziali ed
alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 1999/5/EK.
Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.

Nederlands [Dutch]
IEI Integration Corp dat het toestel toestel in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar [Hungarian]
IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]
IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
IEI Integration Corp declara que este equipam ento está conforme com os requisitos
essenciais e outras disposições da Directiv a 1999/5/CE.

IOVU-210AR-RK39 Panel PC

Page 40

Româna [Romanian]
IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele
esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE.
Slovensko [Slovenian]
IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky

príslušné ustanovenia Smernice 1999/5/E S.
Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin m ui den ehtojen mukainen.
Svenska [Swedish]
IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med de
väsentliga egenskapskrav och övriga relev anta bestämmelser som framgår av direktiv
1999/5/EG.

IOVU-210AR-RK39 Panel PC

Page 41

is equipment complies with Part 15 of the FCC Rules. Operation is subject to the

rsuant to part 15 of the FCC Rules. These limits are designed to provide

commercial environment. This equipment generates, uses, and can radiate radio

nd, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

This equipment generates, uses and can radiate radio frequency energy and, if not

in a particular installation. If this equipment does cause harmful interference to radio or

FCC WARNING

Th
following two conditions:

 This device may not cause harmful interference, and
 This device must accept any interference received, i ncluding interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pu
reasonable protection against harmful interference when the equipment is operated in a

frequency energy a

equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Federal Communication Commission Interference Statement

This equipment has been assembled with components that comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmf ul inte rferen ce in a re sidential install ation.

installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no g uar ant ee that int erf eren ce will n ot occ ur

television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interfer ence by one of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and r eceiver.
 Connect the equipment into an outlet on a circuit diff e rent f rom that t o which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

IOVU-210AR-RK39 Panel PC

Page 42

Appendix

B

B Safety Precautions

IOVU-210AR-RK39 Panel PC

Page 43

The precautions outlined in this chapter should be strictly followed.

WARNING:

Failure to follow these precautions may result in permanent damage to
the IOVU-210AR-RK39.

B.1 Safety Precautions

Please follow the safety precautions out l i ned i n the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the

IOVU-210AR-RK39 is opened.

 Make sure the power is turned off and the power cord is disconnected

whenever the IOVU-210AR-RK39 is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock.

 Electric shocks can occur if the IOVU-210AR-RK39 chassis is opened

when the IOVU-210AR-RK39 is running.

 Do not drop or insert any objects into the ventilation openings of the

IOVU-210AR-RK39.

 If considerable amounts of dust, water, or fluids enter the

IOVU-210AR-RK39, turn off the power supply immediately, unplug the power

cord, and contact the IOVU-210AR-RK39 vendor.

 DO NOT:

o Drop the IOVU-210AR-RK39 against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated temperature

IOVU-210AR-RK39 Panel PC

Page 44

Failure to take ESD precautions during the installation of the

may result in permanent damage to the

B.1.2 Anti-static Precautions

WARNING:

IOVU-210AR-RK39
IOVU-210AR-RK39 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IOVU-210AR-RK39. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the IOVU-210AR-RK39 is opened and any of the electri cal
components are handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component , touch any

grounded conducting material. During the t im e the electrical component is
handled, frequently touch any conducting materials that are connected to the
ground.

 Use an anti-static pad: When configuring or worki ng with an electrical

component, place it on an anti-static pad. This reduces the possibility of ESD
damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical c om ponent by its edges.

IOVU-210AR-RK39 Panel PC

Page 45

Risk of explosion if battery is replaced by an incorrect type. Only

Dispose of used batteries according to instructions and local

B.1.3 Product Disposal

CAUTION:

certified engineers should replace the on-board bat tery.

regulations.

 Outside the European Union - If you wish to dispo se of used electrical and

electronic products outside the Europea n Union, please contact your local
authority so as to comply with the correct dispo sal m ethod.

 Within the European Union:

EU-wide legislation, as implemented in each Membe r State, require s that
waste electrical and electronic products carrying the mark (left) must be
disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow
the guidance of your local authority, or ask the shop where you purchased the product.
The mark on electrical and electronic products only applie s to t he current Europ ean Unio n
Member States.

Please follow the national guidelines for elect rical and electronic product disposal.

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the IOVU-210AR-RK39, please follow t he guidelin es below.

B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the IOVU-210AR-RK39, please read the details
below.

IOVU-210AR-RK39 Panel PC

Page 46

 Never spray or squirt liquids directly onto any other components. To clean the

LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened
cloth.

 The interior of the IOVU-210AR-RK39 does not require cleaning. K eep fluids

away from the IOVU-210AR-RK39 interior.

 Be cautious of all small removable component s when vacuuming the

IOVU-210AR-RK39.

 Turn the IOVU-210AR-RK39 off before cleaning the IOVU-210AR-RK39.
 Never drop any objects or liquids through the openings of the

IOVU-210AR-RK39.

 Be cautious of any possible allergic reactions t o solvents or chemicals used

when cleaning the IOVU-210AR-RK39.

 Avoid eating, drinking and smoking within vicinity of the IOVU-210AR-RK39.

B.2.2 Cleaning Tools

Some components in the IOVU-210AR-RK39 may only be cleaned using a product
specifically designed for the purpose. In such case, the produ ct will be explicitl y mentioned
in the cleaning tips. Below is a list of items to use wh en cleaning the IOVU-210AR-RK39.

 Cloth – Although paper towels or tissues can be used, a soft, clean piece of

cloth is recommended when cleaning the IOVU-210AR-RK39.

 Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol

can be used to clean the IOVU-210AR-RK39.

 Using solvents – T he use of solvents is not recomm ended when cleaning the

IOVU-210AR-RK39 as they may damage the plastic parts.

 Vacuum cleaner – U sing a vacuum specifically designed for computers is

one of the best methods of cleaning the IOVU-210AR-RK39. Dust and dirt
can restrict the airflow in the IOVU-210AR-RK39 and cause its circuitry to
corrode.

 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

IOVU-210AR-RK39 Panel PC

Page 47

Appendix

C

C Hazardous Materials

Disclosure

IOVU-210AR-RK39 Panel PC

Page 48

The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain material s in the product, and is appli cable to China
RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.

Please refer to below table.

Part Name Toxic or Hazardous Substances and Elements

Lead
(Pb)

Housing
Display
Printed Circuit
Board
Metal Fasteners
Cable Assembly
Fan Assembly
Power Supply
Assemblies
Battery
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit

requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homogeneous mat erials for this part is above

O O O O O O
O O O O O O
O O O O O O

O O O O O O
O O O O O O
O O O O O O
O O O O O O

O O O O O O

Mercury
(Hg)

Cadmium
(Cd)

Hexavalent
Chromium
(CR(VI))

Polybrominated
Biphenyls
(PBB)

Polybrominated
Diphenyl Ethers
(PBDE)

the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

IOVU-210AR-RK39 Panel PC

Page 49

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称

壳体
显示
印刷电路板
金属螺帽
电缆组装
风扇组装
电力供应组装
电池

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(CR(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 (现由 GB/T 26572-2011 取代)
标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 (现由 GB/T 26572-2011

取代) 标准规定的限量要求。