IEI Technology IOVU-207AR-RK39 User Manual

IOVU-207AR-RK39 Panel PC

Page i

7" RISC-Based Panel PC with Touchscreen,

MODEL:

IOVU-207AR-RK39

Rev. 1.00 – October 9, 2018

Rockchip RK3399 On-board SoC, Wi-Fi, Bluetooth, GbE,

Camera, USB, SOS Key, Android 7.1, RoHS Compliant

User Manual

IOVU-207AR-RK39 Panel PC

Page ii

Date Version Changes

October 9, 2018 1.00 Initial release

Revision

IOVU-207AR-RK39 Panel PC

Page iii

Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

IOVU-207AR-RK39 Panel PC

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the

equipment or result in personal injury. Warnings should be taken

seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of

losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical

information. These messages should be read carefully as any directions

or instructions contained therein can help avoid making mistakes.

IOVU-207AR-RK39 Panel PC

Page v

Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1 OVERVIEW .................................................................................................................. 2

1.2 FEATURES ................................................................................................................... 2

1.3 FRONT PANEL ............................................................................................................. 3

1.4 REAR PANEL ............................................................................................................... 4

1.5 SYSTEM SPECIFICATIONS ............................................................................................ 5

1.6 DIMENSIONS ............................................................................................................... 7

2 UNPACKING ................................................................................................................. 8

2.1 PACKING LIST ............................................................................................................. 9

2.2 OPTIONAL ITEM ........................................................................................................ 10

3 INSTALLATION .......................................................................................................... 11

3.1 ANTI-ST AT I C PRECAUTIONS ...................................................................................... 12

3.2 INSTALLATION PRECAUTIONS ................................................................................... 12

3.3 EXTERNAL I/O CONNECTORS ................................................................................... 13

3.3.1 Ethernet Connector .......................................................................................... 13

3.3.2 Terminal Block for SOS Key ............................................................................ 14

3.3.3 USB Connectors ............................................................................................... 14

3.4 MOUNTING THE SYSTEM .......................................................................................... 15

3.5 POWER-ON PROCEDURE ........................................................................................... 17

3.6 AVAILABLE DRIVERS ................................................................................................ 18

3.6.1 Driver Download ............................................................................................. 19

3.7 SYSTEM MAINTENANCE ........................................................................................... 20

4 ANDROID OS .............................................................................................................. 21

4.1 HOME SCREEN ......................................................................................................... 22

4.1.1 Adding a Home Screen ..................................................................................... 22

4.1.2 Switching between Home Screens .................................................................... 23

4.1.3 Favorites Tray .................................................................................................. 23

4.1.4 Adding Shortcuts .............................................................................................. 24

IOVU-207AR-RK39 Panel PC

Page vi

4.1.5 Arranging the Home Screen ............................................................................. 26

4.2 NAVIGATION BUTTONS ............................................................................................. 27

4.3 STAT U S BAR ............................................................................................................. 28

A REGULATORY COMPLIANCE .............................................................................. 30

B SAFETY PRECAUTIONS ......................................................................................... 35

B.1 SAFETY PRECAUTIONS ............................................................................................. 36

B.1.1 General Safety Precautions ............................................................................. 36

B.1.2 Anti-static Precautions .................................................................................... 37

B.1.3 Product Disposal ............................................................................................. 38

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 38

B.2.1 Maintenance and Cleaning .............................................................................. 38

B.2.2 Cleaning Tools ................................................................................................. 39

C HAZARDOUS MATERIALS DISCLOSURE ......................................................... 40

IOVU-207AR-RK39 Panel PC

Page vii

List of Figures

Figure 1-1: IOVU-207AR-RK39 Panel PC ...................................................................................... 2

Figure 1-2: Front Panel .................................................................................................................. 3

Figure 1-3: Rear Panel .................................................................................................................... 4

Figure 1-4: Dimensions (Unit: mm) ............................................................................................... 7

Figure 3-1: Ethernet Connector Pin Locations .......................................................................... 13

Figure 3-2: Terminal Block Pin Locations .................................................................................. 14

Figure 3-3: USB Connectors ........................................................................................................ 14

Figure 3-4: Wall Mounting Bracket Installation ......................................................................... 15

Figure 3-5: Secure Mounting Screws ......................................................................................... 16

Figure 3-6: Mounting Panel PC ................................................................................................... 16

Figure 3-7: Wall Mount Bracket Dimensions (Unit: mm) .......................................................... 17

Figure 3-8: Power Input Jack ....................................................................................................... 18

Figure 3-9: IEI Resource Download Center ................................................................................ 18

Figure 4-1: Adding a Home Screen ............................................................................................. 22

Figure 4-2: Multiple Home Screens ............................................................................................. 23

Figure 4-3: Favorites Tray ............................................................................................................ 23

Figure 4-4: All Apps/WIDGETS Page .......................................................................................... 25

Figure 4-5: Trash an Item on Home Screen ............................................................................... 26

Figure 4-6: Navigation Buttons ................................................................................................... 27

Figure 4-7: Status Bar .................................................................................................................. 28

Figure 4-8: Notification List and System Status ........................................................................ 29

IOVU-207AR-RK39 Panel PC

Page viii

List of Tables

Table 1-1: Technical Specifications .............................................................................................. 6

Table 2-1: Packing List ................................................................................................................. 10

Table 2-2: Optional Item ............................................................................................................... 10

Table 3-1: Ethernet Connector Pinouts ...................................................................................... 13

Table 3-2: Terminal Block Pinouts .............................................................................................. 14

Table 4-1: Navigation Buttons ..................................................................................................... 27

IOVU-207AR-RK39 Panel PC

Page 1

Chapter

1

1 Introduction

IOVU-207AR-RK39 Panel PC

Page 2

1.1 Overview

Figure 1-1: IOVU-207AR-RK39 Panel PC

The IOVU-207AR-RK39 is a 7" RISC-based panel PC with Android 7.1 OS. At the heart of

the system is the Rockchip RK3399 on-board SoC, offering low power in a powerful

package. The IOVU-207AR-RK39 provides rich input capabilities utilizing the projected

capacitive touchscreen. Other peripherals include one USB 2.0 port, one USB 3.0 port,

one 10/100/1000 Mbps LAN port and one microSD slot.

1.2 Features

The IOVU-207AR-RK39 features the following:

 Fanless design

 Rockchip RK3399 on-board SoC

 On-board 1866 MHz 2 GB LPDDR3 memory

 16 GB eMMC NAND flash

 Projected capacitive touchscreen

 Equips with Wi-Fi 802.11a/b/g/n/ac and Bluetooth v4.1

 SOS button for calling help in emergency

 Two programmable function keys

 One 10/100/1000 Mbps Ethernet LAN port

 One USB 3.0 port and one USB 2.0 port

 Android 7.1 OS pre-installed

 RoHS compliant

IOVU-207AR-RK39 Panel PC

Page 3

1.3 Front Panel

The front panel of the IOVU-207AR-RK39 contains a 7" LCD with projected capacitive

touchscreen, 5-megapixel camera, a 2W speaker, a digital microphone, an SOS key, two

programmable function keys, a reset button and four LED indicators.

Figure 1-2: Front Panel

The states of the LED indicators located on the front panel are listed below.

Power LED

Alert LED

Phone LED

E-mail LED

Off The system is turned off.

Green The system is turned on.

Off No alert

Red Alert message

Off No missed call

Green Missed call notification

Off No new e-mail

Blue E-mail notification

IOVU-207AR-RK39 Panel PC

Page 4

1.4 Rear Panel

The rear panel contains several I/O interfaces as shown below.

Figure 1-3: Rear Panel

IOVU-207AR-RK39 Panel PC

Page 5

1.5 System Specifications

The IOVU-207AR-RK39 technical specifications are listed below.

System

CPU Rockchip RK3399 on-board SoC

Memory 2 GB 1866 MHz LPDDR3L on-board memory

Storage 16 GB eMMC NAND flash

Audio 1 x Speaker (2 W)

Camera 5-megapixel front-facing camera

Thermal Solution Fanless

Watchdog Timer Yes

Real-time Clock Battery backup RTC

OS Android 7.1

Display

LCD Size 7"

Max. Resolution 720 x 1280

(dual-core Cortex-A72 + quad-core Cortex-A53, 64-bit)

One microSD card slot (rear panel)

1 x Digital microphone

Brightness (cd/m2) 300 (typ.)

Contrast Ratio 800:1 (typ.)

Pixel Pitch (mm) 0.1239 (H) x 0.119 (V)

Viewing Angle 70/70/70/70 degree

Touchscreen Projected capacitive touchscreen

Communication

Wireless LAN 802.11a/b/g/n/ac

Bluetooth Bluetooth v4.1

Power

Power Input 9 V ~ 30 V DC

DC input: φ2.5/5.5mm DC jack

Physical Character

Construction Material PC+ABS plastic front cover and metal rear cover

Color White

IOVU-207AR-RK39 Panel PC

Page 6

Mounting VESA 75 mm x 75 mm

Dimensions (W x H x D) 210.7 mm x 154.7 mm x 29.6 mm

Operation Temperature -10°C ~ 50°C (14°F ~ 122°F) with air flow

Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)

Humidity 10% ~ 95%, non-condensing

Weight (Net) 0.72 kg

Certifications CE, FCC Class B

Connectors, Buttons and Indicators

External I/O 1 x USB 3.0 Typ e -A port

1 x USB 2.0 Type-A port

1 x RJ-45 GbE port (by RTL8211E)

1 x Terminal block (2-pin) for SOS key

Internal I/O 2 x UART pin header with 3 V

2 x USB 2.0 pin header

Button 1 x Reset button

1 x SOS button (red bar)

2 x Function key (green bar)

LED Indicators 1 x Power

1 x E-mail

1 x Phone

1 x Exclamation mark

Table 1-1: Technical Specifications

IOVU-207AR-RK39 Panel PC

Page 7

1.6 Dimensions

The dimensions are shown below.

Figure 1-4: Dimensions (Unit: mm)

IOVU-207AR-RK39 Panel PC

Page 8

Chapter

2

2 Unpacking

IOVU-207AR-RK39 Panel PC

Page 9

has been

properly installed. This ensures the screen is protected during the

was purchased from or contact an IEI sales

To unpack the panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the

screen. Only remove the plastic cover after the system

installation process.

Step 1: Carefully cut the tape sealing the box. Only cut deep enough to break the tape.

Step 2: Open the box.

Step 3: Lift the IOVU-207AR-RK39 out of the box.

Step 4: Make sure all the components listed in the packing list are present. Step 0:

2.1 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do

not proceed with the installation. Contact the IEI reseller or vendor the

IOVU-207AR-RK39

representative directly by sending an email to [e-mail].

The IOVU-207AR-RK39 is shipped with the following components:

Quantity Item Image

1 IOVU-207AR-RK39 panel PC

IOVU-207AR-RK39 Panel PC

Page 10

Table 2-1: Packing List

Quantity Item Image

1 Wall mount bracket

4 M4*6 screw for wall mounting

1 M3*4 screw for wall mounting

2.2 Optional Item

The following is optional component which may be separately purchased:

Item Image

90V~264V AC input, 12V/60W DC power adapter

(P/N: 63040-010060-120-RS)

Table 2-2: Optional Item

IOVU-207AR-RK39 Panel PC

Page 11

Chapter

3

3 Installation

IOVU-207AR-RK39 Panel PC

Page 12

Failure to take ESD precautions during the maintenance of the

may result in permanent damage to the

3.1 Anti-static Precautions

WARNING:

IOVU-207AR-RK39

IOVU-207AR-RK39 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the IOVU-207AR-RK39. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the IOVU-207AR-RK39 is accessed internally, or any

other electrical component is handled, the following anti-static precautions are strictly

adhered to.

 Wear an anti-static wristband: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

 Use an anti-static pad: - When configuring the IOVU-207AR-RK39, place it on

an anti-static pad. This reduces the possibility of ESD damaging the

IOVU-207AR-RK39.

 Only handle the edges of the PCB: - When handling the PCB, hold the PCB

by the edges.

3.2 Installation Precautions

When installing the flat panel PC, please follow the precautions listed below:

 Power turned off: When installing the flat panel PC, make sure the power is

off. Failing to turn off the power may cause severe injury to the body and/or

damage to the system.

 Certified Engineers: Only certified engineers should install and modify

onboard functionalities.

IOVU-207AR-RK39 Panel PC

Page 13

 Anti-static Discharge: If a user open the rear panel of the flat panel PC, to

configure the jumpers or plug in added peripheral devices, ground themselves

first and wear and anti-static wristband.

3.3 External I/O Connectors

This section provides an overview of the external I/O connectors of the

IOVU-207AR-RK39.

3.3.1 Ethernet Connector

There is one external RJ-45 LAN connector. The RJ-45 connector enables connection to

an external network. The Ethernet connector pinouts are shown below.

Pin Description

1 LAN1_MDX0+

2 LAN1_MDX0-

3 LAN1_MDX1+

4 LAN1_MDIX2+

5 LAN1_MDX2-

6 LAN1_MDX1-

7 LAN1_MDIX3+

8 LAN1_MDX3-

Table 3-1: Ethernet Connector Pinouts

Figure 3-1: Ethernet Connector Pin Locations

IOVU-207AR-RK39 Panel PC

Page 14

3.3.2 Terminal Block for SOS Key

The 2-pin terminal block on the system rear panel provides SOS signal connection. The

pinouts for the terminal block are listed in the figure and table below.

Pin Description

1 SOS_COM1

2 SOS_COM2

Table 3-2: Terminal Block Pinouts

Figure 3-2: Terminal Block Pin Locations

3.3.3 USB Connectors

The external USB Series "A" receptacle connectors provide easier and quicker access to

external USB devices.

Figure 3-3: USB Connectors

IOVU-207AR-RK39 Panel PC

Page 15

the replacement screw should be not

3.4 Mounting the System

To mount the IOVU-207AR-RK39 onto a wall, please follow the steps below.

Step 1: Select a location on the wall for the wall-mounting bracket. Carefully mark the

locations of the screw holes of the wall mounting bracket on the mounting area.

Drill the pilot holes at the marked locations (Figure 3-4

Step 2: Secure the mounting bracket to the wall by inserting the retention screws into

the four pilot holes and tightening them (Figure 3-4

).

).

Figure 3-4: Wall Mounting Bracket Installation

Step 3: Insert the four mounting screws (M4*6) came with the panel PC into the four

screw holes on the mounting bracket and tighten until the screw shank is

secured (Figure 3-5).

CAUTION:

Please use the M4 screws provided in

the package for the mounting screws. If

the screw is missing, the thread depth of

more than 4 mm.

IOVU-207AR-RK39 Panel PC

Page 16

Figure 3-5: Secure Mounting Screws

Step 4: Align the mounting holes on the rear of the panel PC with the mounting screws.

Step 5: Carefully attach the panel PC to the mounting screws and gently pull the panel

PC downwards until the panel PC rests securely on screws. Ensure that all four

of the slotted holes fit snuggly into their respective mounting screws

(Figure 3-6

Step 6: Secure the panel PC by installing the retention screw (M3*4) came with the

panel PC into the screw hole on the bottom of the bracket (Figure 3-6

).

).

Figure 3-6: Mounting Panel PC

IOVU-207AR-RK39 Panel PC

Page 17

sure a power supply with the correct input voltage is being fed into

The dimensions of the wall mount bracket shipped with the system are shown below.

Figure 3-7: Wall Mount Bracket Dimensions (Unit: mm)

3.5 Power-On Procedure

WARNING:

Make

the system. Incorrect voltages applied to the system may cause damage to

the internal electronic components and may also cause injury to the user.

The IOVU-207AR-RK39 supports 9 V ~ 30 V DC power input. To power-on, connect the

IOVU-207AR-RK39 power input jack to a power source. Once connected, the system will

automatically turn on and the power LED on the front panel will light up in green.

IOVU-207AR-RK39 Panel PC

Page 18

Figure 3-9: IEI Resource Download Center

Figure 3-8: Power Input Jack

3.6 Available Drivers

All the drivers for the IOVU-207AR-RK39 are available on IEI Resource Download Center

(https://download.ieiworld.com

relevant software, utilities, and documentation.

). Type IOVU-207AR-RK39 and press Enter to find all the

IOVU-207AR-RK39 Panel PC

Page 19

3.6.1 Driver Download

To download drivers from IEI Resource Download Center, follow the steps below.

Step 1: Go to https://download.ieiworld.com

Step 2: All product-related software, utilities, and documentation will be listed. You can

choose Driver to filter the result.

. Type IOVU-207AR-RK39 and press Enter.

Step 3: Click the driver file name on the page and you will be prompted with the

following window. You can download the entire ISO file (

arrow to find an individual driver and click the file name to download (

), or click the small

).

IOVU-207AR-RK39 Panel PC

Page 20

3.7 System Maintenance

If the components of the IOVU-207AR-RK39 fail, they must be replaced. Please contact

the system reseller or vendor to purchase the replacement parts.

NOTE:

A user cannot replace a motherboard. If the motherboard fails it must

be shipped back to IEI to be replaced. Please contact the system

vendor, reseller or an IEI sales person directly.

IOVU-207AR-RK39 Panel PC

Page 21

Chapter

4

4 Android OS

IOVU-207AR-RK39 Panel PC

Page 22

The IOVU-207AR-RK39 comes with Android OS pre-installed. This chapter introduces the

user interface and basic functions of Android OS installed in the IOVU-207AR-RK39.

4.1 Home Screen

Android OS supports multiple home screens allowing users to customize the screen with

widgets, apps and shortcuts. The following sections describe the basic technique to

manage the home screen.

4.1.1 Adding a Home Screen

To add a home screen, touch and hold an app/widget icon. The following screen appears,

indicating that a new home screen is available. Drag and release the icon to the new home

screen.

Figure 4-1: Adding a Home Screen

IOVU-207AR-RK39 Panel PC

Page 23

4.1.2 Switching between Home Screens

Swipe right or left to switch between home screens.

Figure 4-2: Multiple Home Screens

4.1.3 Favorites Tray

The Favorites tray at the bottom of each home screen allows users to keep the most

important or frequently used shortcuts.

Figure 4-3: Favorites Tray

IOVU-207AR-RK39 Panel PC

Page 24

4.1.4 Adding Shortcuts

To add app or widget shortcuts on the home screen, follow the steps below.

Step 1: To add an app shortcut, tap the up arrow on the home screen to access the

All Apps page.

To add a widget shortcut, touch and hold the background of a home screen, then

tap WIDGETS.

IOVU-207AR-RK39 Panel PC

Page 25

Step 2: Touch and hold an app icon or a widget, and drag it to the home screen.

Figure 4-4: All Apps/WIDGETS Page

IOVU-207AR-RK39 Panel PC

Page 26

4.1.5 Arranging the Home Screen

The items on the home screen can be moved and deleted. Touch and hold an item on the

home screen and drag it where you want. To trash the item on the screen, drag it to the

Remove icon. Release the icon when it turns gray.

Figure 4-5: Trash an Item on Home Screen

IOVU-207AR-RK39 Panel PC

Page 27

4.2 Navigation Buttons

The navigation buttons shown in Figure 4-8 can always be found at the bottom of every

screen.

Figure 4-6: Navigation Buttons

Buttons Description

Table 4-1: Navigation Buttons

Tap to turn the volume down.

Tap to return to the previous screen.

Tap to return to the home screen.

Tap to display all the recently used applications.

Tap to turn the volume up.

Tap to take a screenshot.

IOVU-207AR-RK39 Panel PC

Page 28

4.3 Status Bar

The status bar on the top of the screen (Figure 4-9) displays system status, such as

battery level or signal strength.

Figure 4-7: Status Bar

Swipe down from the status bar to view notification and status details (Figure 4-10).

IOVU-207AR-RK39 Panel PC

Page 29

Figure 4-8: Notification List and System Status

IOVU-207AR-RK39 Panel PC

Page 30

Appendix

A

A Regulatory Compliance

IOVU-207AR-RK39 Panel PC

Page 31

f the user modifies and/or install other devices in the equipment, the CE conformity

has telecommunications functionality, it also complies with the

o

DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive 2004/108/EC

 Low-Voltage Directive 2006/95/EC

 RoHS II Directive 2011/65/EU

I

declaration may no longer apply.

If this equipment

requirements of the R&TTE Directive 1999/5/EC.

English

IEI Integration Corp declares that this equipment is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Български [Bulgarian]

IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива 1999/5/ЕС.

Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními

požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]

IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav

øvrige relevante krav i direktiv 1999/5/EF.

Deutsch [German]

IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen

und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

Eesti [Estonian]

IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 1999/5/EÜ

põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

IOVU-207AR-RK39 Panel PC

Page 32

Español [Spanish]

IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική [Greek]

IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

1999/5/ΕΚ.

Français [French]

IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux

autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]

IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed

alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski [Latvian]

IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 1999/5/EK.

Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

1999/5/EB Direktyvos nuostatas.

Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel in overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn 1999/5/EG.

Malti [Maltese]

IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma

provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar [Hungarian]

IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz

pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português [Portuguese]

IEI Integration Corp declara que este equipamento está conforme com os requisitos

essenciais e outras disposições da Directiva 1999/5/CE.

IOVU-207AR-RK39 Panel PC

Page 33

Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele

esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE.

Slovensko [Slovenian]

IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi

relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky

príslušné ustanovenia Smernice 1999/5/ES.

Suomi [Finnish]

IEI Integration Corp vakuuttaa täten etä laitteet on direktiivin 1999/5/EY oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med de

väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

1999/5/EG.

IOVU-207AR-RK39 Panel PC

Page 34

is equipment complies with Part 15 of the FCC Rules. Operation is subject to the

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

adiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

frequency energy and, if not

FCC WARNING

Th

following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can r

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Federal Communication Commission Interference Statement

This equipment has been assembled with components that comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

IOVU-207AR-RK39 Panel PC

Page 35

Appendix

B

B Safety Precautions

IOVU-207AR-RK39 Panel PC

Page 36

The precautions outlined in this chapter should be strictly followed.

WARNING:

Failure to follow these precautions may result in permanent damage to

the IOVU-207AR-RK39.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the

IOVU-207AR-RK39 is opened.

 Make sure the power is turned off and the power cord is disconnected

whenever the IOVU-207AR-RK39 is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock.

 Electric shocks can occur if the IOVU-207AR-RK39 chassis is opened

when the IOVU-207AR-RK39 is running.

 Do not drop or insert any objects into the ventilation openings of the

IOVU-207AR-RK39.

 If considerable amounts of dust, water, or fluids enter the

IOVU-207AR-RK39, turn off the power supply immediately, unplug the power

cord, and contact the IOVU-207AR-RK39 vendor.

 DO NOT:

o Drop the IOVU-207AR-RK39 against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated temperature

IOVU-207AR-RK39 Panel PC

Page 37

Failure to take ESD precautions during the installation of the

ge to the

B.1.2 Anti-static Precautions

WARNING:

IOVU-207AR-RK39 may result in permanent dama

IOVU-207AR-RK39 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the IOVU-207AR-RK39. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the IOVU-207AR-RK39 is opened and any of the electrical

components are handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component, touch any

grounded conducting material. During the time the electrical component is

handled, frequently touch any conducting materials that are connected to the

ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an anti-static pad. This reduces the possibility of ESD

damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical component by its edges.

IOVU-207AR-RK39 Panel PC

Page 38

Risk of explosion if battery is replaced by an incorrect type. Only

Dispose of used batteries according to instructions and local

B.1.3 Product Disposal

CAUTION:

certified engineers should replace the on-board battery.

regulations.

 Outside the European Union - If you wish to dispose of used electrical and

electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

 Within the European Union:

EU-wide legislation, as implemented in each Member State, requires that

waste electrical and electronic products carrying the mark (left) must be

disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow

the guidance of your local authority, or ask the shop where you purchased the product.

The mark on electrical and electronic products only applies to the current European Union

Member States.

Please follow the national guidelines for electrical and electronic product disposal.

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the IOVU-207AR-RK39, please follow the guidelines below.

B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the IOVU-207AR-RK39, please read the details

below.

IOVU-207AR-RK39 Panel PC

Page 39

 Never spray or squirt liquids directly onto any other components. To clean the

LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened

cloth.

 The interior of the IOVU-207AR-RK39 does not require cleaning. Keep fluids

away from the IOVU-207AR-RK39 interior.

 Be cautious of all small removable components when vacuuming the

IOVU-207AR-RK39.

 Turn the IOVU-207AR-RK39 off before cleaning the IOVU-207AR-RK39.

 Never drop any objects or liquids through the openings of the

IOVU-207AR-RK39.

 Be cautious of any possible allergic reactions to solvents or chemicals used

when cleaning the IOVU-207AR-RK39.

 Avoid eating, drinking and smoking within vicinity of the IOVU-207AR-RK39.

B.2.2 Cleaning Tools

Some components in the IOVU-207AR-RK39 may only be cleaned using a product

specifically designed for the purpose. In such case, the product will be explicitly mentioned

in the cleaning tips. Below is a list of items to use when cleaning the IOVU-207AR-RK39.

 Cloth – Although paper towels or tissues can be used, a soft, clean piece of

cloth is recommended when cleaning the IOVU-207AR-RK39.

 Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol

can be used to clean the IOVU-207AR-RK39.

 Using solvents – The use of solvents is not recommended when cleaning the

IOVU-207AR-RK39 as they may damage the plastic parts.

 Vacuum cleaner – Using a vacuum specifically designed for computers is

one of the best methods of cleaning the IOVU-207AR-RK39. Dust and dirt

can restrict the airflow in the IOVU-207AR-RK39 and cause its circuitry to

corrode.

 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

IOVU-207AR-RK39 Panel PC

Page 40

Appendix

C

C Hazardous Materials

Disclosure

IOVU-207AR-RK39 Panel PC

Page 41

The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the

presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances

would “not leak out or undergo abrupt change.” This product may contain replaceable

sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to below table.

Part Name Toxic or Hazardous Substances and Elements

Lead

(Pb)

Housing

Display

Printed Circuit

Board

Metal Fasteners

Cable Assembly

Fan Assembly

Power Supply

Assemblies

Battery

O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit

requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(CR(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl Ethers

(PBDE)

the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

IOVU-207AR-RK39 Panel PC

Page 42

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符

合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称

壳体

显示

印刷电路板

金属螺帽

电缆组装

风扇组装

电力供应组装

电池

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(CR(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 (现由 GB/T 26572-2011 取代)

标准规定的限量要求以下。

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 (现由 GB/T 26572-2011

取代) 标准规定的限量要求。