IEI Technology IOBA-10F-AD User Manual

IOBA-10F-AD RISC-based Panel PC

Page i

NFC, PoE, DIO and Sensor Con n e ct or s

MODEL:

IOBA-10F-AD

Rev. 1.00 – March 16, 2018

10.1” RISC-Based Panel PC with Touchscreen,

Freescale™ i.MX6 Cortex™-A9 Quad-Core 1.0 GHz CPU,

Android 5.1 OS, Front Camera, COM, Wi-Fi, Bluetooth,

User Manual

IOBA-10F-AD RISC-based Panel PC

Page ii

Date Version Changes

March 16, 2018 1.00 Initial release

Revision

IOBA-10F-AD RISC-based Panel PC

Page iii

Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibil ity of such damages.

This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

IOBA-10F-AD RISC-based Panel PC

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.

NOTE

These messages inform the reader of essent ial but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein ca n help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that shoul d not be touched without
taking care.

IOBA-10F-AD RISC-based Panel PC

Page v

Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1 OVERVIEW .................................................................................................................. 2

1.2 MODEL VARIATIONS ................................................................................................... 2

1.3 FEATURES ................................................................................................................... 3

1.4 FRONT PANEL ............................................................................................................. 3

1.5 REAR VIEW ................................................................................................................ 4

1.6 SYSTEM SPECIFICATIONS ............................................................................................ 5

1.7 DIMENSIONS ............................................................................................................... 7

2 UNPACKING ................................................................................................................. 9

2.1 PACKING LIST ........................................................................................................... 10

2.2 OPTIONAL ITEMS ....................................................................................................... 11

3 INSTALLATION ......................................................................................................... 12

3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 13

3.2 INSTALLATION PRECAUTIONS ................................................................................... 13

3.3 EXTERNAL I/O CONNECTORS ................................................................................... 14

3.3.1 9 V ~ 30 V DC Power Jack .............................................................................. 14

3.3.2 AI Connectors (IOBA-10F-AD Only) .............................................................. 14

3.3.3 Digital I/O Connectors (IOBA-10F-AD Only) ................................................ 14

3.3.4 Digital I/O Terminal Block (IOBA-10F-AD Only) ........................................... 15

3.3.5 I2C Connectors (IOBA-10F-AD Only) ............................................................. 15

3.3.6 microSD Card Slot ........................................................................................... 15

3.3.7 RJ-45 LAN Connector ...................................................................................... 16

3.3.8 RS-232 Serial Interface (IOBA-10F-AD Only) ................................................ 16

3.3.9 RS-232/422/485 Serial Interface ...................................................................... 17

3.3.10 USB 2.0 Host Connectors .............................................................................. 17

3.4 MOUNTING THE SYSTEM .......................................................................................... 17

3.5 SYSTEM MAINTENANCE ........................................................................................... 20

4 USING THE IOBA-10F-AD ........................................................................................ 21

IOBA-10F-AD RISC-based Panel PC

Page vi

4.1 POWERING ON/OFF .................................................................................................. 22

4.2 HOME SCREEN ......................................................................................................... 22

4.2.1 Switching between Home Screens .................................................................... 22

4.2.2 Favorites Tray .................................................................................................. 23

4.2.3 Adding Shortcut................................................................................................ 23

4.2.4 Arranging the Home Screen ............................................................................. 24

4.3 NAVIGATION BUTTONS ............................................................................................. 25

4.4 STATUS BAR ............................................................................................................. 26

4.5 SETTINGS ................................................................................................................. 27

4.5.1 Wireless & networks ......................................................................................... 27

4.5.1.1 More Settings ............................................................................................ 28

4.5.2 Display ............................................................................................................. 29

4.5.3 Sound & Notification ....................................................................................... 30

4.5.4 Storage ............................................................................................................. 31

4.5.5 Apps .................................................................................................................. 32

4.5.6 Users ................................................................................................................ 32

4.5.7 Location ........................................................................................................... 33

4.5.8 Security ............................................................................................................ 33

4.5.9 Accounts ........................................................................................................... 35

4.5.10 Language & Input .......................................................................................... 35

4.5.11 Backup & Reset .............................................................................................. 36

4.5.12 Date & Time ................................................................................................... 37

4.5.13 Accessibility ................................................................................................... 38

4.5.14 Printing .......................................................................................................... 39

4.5.15 About Tablet ................................................................................................... 40

4.6 FILE MANAGEMENT ................................................................................................. 41

A REGULATORY COMPLIANCE .............................................................................. 43

B SAFETY PRECAUTIONS ......................................................................................... 48

B.1 SAFETY PRECAUTIONS ............................................................................................. 49

B.1.1 General Safety Precautions ............................................................................. 49

B.1.2 Anti-static Precautions .................................................................................... 50

B.1.3 Product Disposal ............................................................................................. 51

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 51

B.2.1 Maintenance and Cleaning .............................................................................. 51

IOBA-10F-AD RISC-based Panel PC

Page vii

B.2.2 Cleaning T ools ................................................................................................. 52

C HAZARDOUS MATERIALS DISCLOSURE ......................................................... 53

IOBA-10F-AD RISC-based Panel PC

Page viii

List of Figures

Figure 1-1: IOBA-10F-AD Panel PC ............................................................................................... 2

Figure 1-2: IOBA-10F-AD Front Panel ........................................................................................... 3

Figure 1-3: IOBA-10F-AD Rear View ............................................................................................. 4

Figure 1-4: IOBA-10F-AD-ET Rear View ....................................................................................... 4

Figure 1-5: IOBA-10F-AD Dimensions (unit: mm) ....................................................................... 7

Figure 1-6: IOBA-10F-AD-ET Dimensions (unit: mm) ................................................................. 8

Figure 3-1: 9 V ~ 30 V DC Power Jack ........................................................................................ 14

Figure 3-2: microSD Card Slot .................................................................................................... 15

Figure 3-3: USB 2.0 Host Connector ........................................................................................... 17

Figure 3-4: IOBA-10F-AD Wall-mounting Bracket ..................................................................... 18

Figure 3-5: IOBA-10F-AD-ET Wall-mounting Bracket ............................................................... 18

Figure 3-6: Mounting Screws ...................................................................................................... 19

Figure 3-7: Panel PC Mounting Holes ......................................................................................... 19

Figure 3-8: Securing to the Wall-Mounting Bracket .................................................................. 20

Figure 4-1: Multiple Home Screens ............................................................................................. 22

Figure 4-2: Favorites Tray ............................................................................................................ 23

Figure 4-3: APPS Page ................................................................................................................. 24

Figure 4-4: Move and Trash Item on Home Screen ................................................................... 24

Figure 4-5: Navigation Buttons ................................................................................................... 25

Figure 4-6: Status Bar .................................................................................................................. 26

Figure 4-7: Pending Notification List .......................................................................................... 26

Figure 4-8: Wireless and Networks Settings ............................................................................. 27

Figure 4-9: More Settings Menu .................................................................................................. 28

Figure 4-10: Display Menu ........................................................................................................... 29

Figure 4-11: Sound & Notification Menu .................................................................................... 30

Figure 4-12: Storage Menu .......................................................................................................... 31

Figure 4-13: Apps Menu ............................................................................................................... 32

Figure 4-14: Users Menu .............................................................................................................. 32

Figure 4-15: Location Menu ......................................................................................................... 33

Figure 4-16: Security Menu .......................................................................................................... 33

IOBA-10F-AD RISC-based Panel PC

Page ix

Figure 4-17: Accounts Menu ....................................................................................................... 35

Figure 4-18: Language & Input Menu ......................................................................................... 35

Figure 4-19: Backup & Reset Menu ............................................................................................ 36

Figure 4-20: Date & Time Menu ................................................................................................... 37

Figure 4-21: Accessibility Menu .................................................................................................. 38

Figure 4-22: Printing Menu .......................................................................................................... 39

Figure 4-23: About Tablet Menu .................................................................................................. 40

Figure 4-24: ES File Explorer Screen .......................................................................................... 41

Figure 4-25: Possible Storage Devices ...................................................................................... 42

IOBA-10F-AD RISC-based Panel PC

Page x

List of Tables

Table 1-1: Model Variations ........................................................................................................... 2

Table 1-2: Technical Specifications .............................................................................................. 6

Table 2-1: Packing List ................................................................................................................. 11

Table 2-2: Optional Items ............................................................................................................. 11

Table 3-1: AI Connector (AI) Pinouts .......................................................................................... 14

Table 3-2: DIO Connector (DIO2, DIO3) Pinouts ........................................................................ 14

Table 3-3: DIO Terminal Block (DIO1) Pinouts .......................................................................... 15

Table 3-4: I2C Connector (I2C) Pinouts ....................................................................................... 15

Table 3-5: RJ-45 LAN Connector Pinouts .................................................................................. 16

Table 3-6: RS-232 Connector (UART2) Pinouts ......................................................................... 16

Table 3-7: RS-232/422/485 Terminal Block (UART1) Pinouts ................................................... 17

Table 4-1: Navigation Buttons ..................................................................................................... 25

IOBA-10F-AD RISC-based Panel PC

Page 1

Chapter

1

1 Introduction

IOBA-10F-AD RISC-based Panel PC

Page 2

1.1 Overview

Figure 1-1: IOBA-10F-AD Panel PC

The IOBA-10F-AD is a 10.1” RISC-based panel PC with Android 5.1 OS. At the heart of
the system is the Freescale™ i.MX6 Cortex™-A9 quad-core processor, offering low power
in a powerful package. The IOBA-10F-AD provides rich input capabilities utilizing the
projected capacitive touchscreen. Other peripherals include one micorSD card slot, two
USB 2.0 host ports, one RS-232/422/485 port and one 10/100/1000 Mbps LAN port.

1.2 Model Variations

Model Wi-Fi & Bluetooth NFC PoE

IOBA-10F-AD
IOBA-10F-AD-ET
Table 1-1: Model Variations

DIO, Sensor Connectors
& Function Keys

Yes Yes Yes Yes

No No No No

IOBA-10F-AD RISC-based Panel PC

Page 3

The RFID reader and volume up, volume down and SOS keys are

Figure 1-2: IOBA-10F-AD Front Panel

1.3 Features

The IOBA-10F-AD features the following:

 10.1” 1280 x 800 LCD
 Projected capacitive touchscreen
 Android 5.1 OS
 Freescale™ i.MX6 Cortex™-A9 quad-core processor
 On-board 2 GB DDR3 memory
 8 GB eMMC NAND flash
 IoT sensor connectors in Grove interface
 IP 64 compliant front panel

1.4 Front Panel

The front panel of the IOBA-10F-AD contains the 10.1” LCD w ith capaci tive touchs creen,
2-megapixel webcam and power LED.

NOTE:

available for the IOBA-10F-AD model only.

IOBA-10F-AD RISC-based Panel PC

Page 4

Figure 1-4: IOBA-10F-AD-ET Rear View

1.5 Rear View

The rear of the IOBA-10F-AD contains the I/O interfaces as shown in Figure 1-3 and
Figure 1-4.

Figure 1-3: IOBA-10F-AD Rear View

IOBA-10F-AD RISC-based Panel PC

Page 5

1.6 System Specifications

The IOBA-10F-AD technical specifications are listed in Table 1-2.

LCD Size 10.1” (16:9)
Resolution 1280 (W) x 800 (H)
Brightness (cd/m2) 300
Contrast Ratio 800:1
LCD Color 262K
Pixel Pitch (mm) 0.1695 x 0.1695
Viewing Angle 85/85/85/85 degree
Backlight MTBF (hrs) 20,000
Touchscreen Projected capacitive
CPU Freescale™ i.MX6 Cortex™-A9 quad-core, 1.0 GHz
RAM 2 GB DDR3 SDRAM
Boot Flash 8 GB eMMC NAND flash
OS Android 5.1

Audio

Camera 2-megapixel CMOS webcam

Wi-Fi and Bluetooth

NFC

I/O Interfaces

2 x Speakers (2 W)
1 x Microphone

Bluetooth v4.0 + Wi-Fi controller for 802.11a/b/g/n
(IOBA-10F-AD model only)

13.56 MHz NFC compliant with ISO/IEC15693 and
ISO/IEC14443A (IOBA-10F-AD model only)
1 x 10/100/1000 Mbps RJ-45 port
1 x RS-232/422/485 (4-pin terminal block)
1 x microSD card slot (max. 32 GB)
1 x Power jack (9 V ~ 30 V DC)
1 x Reset key
2 x USB 2.0 host ports

The following interfaces are available for
IOBA-10F-AD model only:

1 x 10/100/1000 Mbps RJ-45 port with PoE
1 x RS-232 (Grove interface)
1 x DIO (6-pin terminal block; 3.3V/50mA software

IOBA-10F-AD RISC-based Panel PC

Page 6

configurable)
2 x DIO (Grove interface; 3.3V/50mA software
configurable)
3 x AI (Grove interface)
3 x I2C (Grove interface)

Thermal Solution Fanless
Construction Material Plastic front cover and rear cover
Mounting Wall mounting
Color White
Operating Temperature 0ºC ~ 50ºC
Storage Temperature -10ºC ~ 60ºC
Humidity 5% ~ 90%, non-condensing
IP Level IP 64 compliant front panel
Power Requirement 9 V ~ 30 V DC
Dimensions (W x H x D) 282.5 mm x 174.3 mm x 14.7 mm

Net Weight

IOBA-10F-AD: 870 g
IOBA-10F-AD-ET: 856.5 g

Table 1-2: Technical Specifications

IOBA-10F-AD RISC-based Panel PC

Page 7

1.7 Dimensions

The dimensions are shown below.

Figure 1-5: IOBA-10F-AD Dimensions (unit: mm)

IOBA-10F-AD RISC-based Panel PC

Page 8

Figure 1-6: IOBA-10F-AD-ET Dimensions (unit: mm)

IOBA-10F-AD RISC-based Panel PC

Page 9

Chapter

2

2 Unpacking

IOBA-10F-AD RISC-based Panel PC

Page 10

has been

properly installed. This ensures the screen is protected during the

was purchased from or contact an IEI sales

To unpack the panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the system

installation process.

Step 1: Carefully cut the tape sealing the box. Onl y cut deep enough to break the tape.

Step 2: Open the box.

Step 3: Lift the IOBA-10F-AD out of the box.

Step 4: Make sure all the components listed in the packing list are present. Step 0:

2.1 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
IOBA-10F-AD
representative directly by sending an email to [e-mail].

The IOBA-10F-AD is shipped with the following components:

Quantity Item Image

1 IOBA-10F-AD RISC-based panel PC

IOBA-10F-AD RISC-based Panel PC

Page 11

Quantity Item Image

1 Wall mounting brack et

(IOBA-10F-AD model only)
(P/N: 41320-0488E4-00-RS)

1 Wall mounting brack et

(IOBA-10F-AD-ET model only)
(P/N: 41320-0489E4-00-RS)

Table 2-1: Packing List

2.2 Optional Items

The following are optional components which may be separately purchased:

Item Image

90V~264V AC input, 12V/60W DC power adapter
(P/N: 63040-010060-130-RS)

In-wall bracket for IOBA-10F-AD model
(P/N: 41320-0490E4-00-RS)

Panel mount kit
(P/N: 19B00-000398-00-RS)

Table 2-2: Optional Items

IOBA-10F-AD RISC-based Panel PC

Page 12

Chapter

3

3 Installation

IOBA-10F-AD RISC-based Panel PC

Page 13

ing the maintenance of the

3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions dur
IOBA-10F-AD may result in permanent damage to the IOBA-10F-AD
and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IOBA-10F-AD. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the IOBA-10F-AD is accessed internally, or any other electrical
component is handled, the following anti-stat i c precautions are strictly adhered to.

 Wear an anti-static wristband: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: - Before handling the board touch a ny grounded conducting

material. During the time the board is handled, f requently touch any
conducting materials that are connected to the ground.

 Use an anti-static pad: - When configuring the IOBA-10F-AD, pla ce it on an

anti-static pad. This reduces the possibility of ES D dam aging t he IOBA-10F-AD.

 Only handle the edges of the PCB: - When handling the PCB, hold the PCB

by the edges.

3.2 Installation Precautions

When installing the flat panel PC, please follow the precaution s li sted below:

 Power turned off: When installing the flat panel PC, make sure the power is

off. Failing to turn of f the power may cause severe injury to the body and/or
damage to the system.

 Certified Engineers: Only certified engineers should install and modify

onboard functionalities.

 Anti-static Discharge: I f a user open the rear panel of the flat panel PC, to

configure the jumpers or plug in added peripheral dev ices, ground themselves
first and wear and anti-static wristband.

IOBA-10F-AD RISC-based Panel PC

Page 14

Table 3-2: DIO Connector (DIO2, DIO3) Pinouts

3.3 External I/O Connectors

This section provides an overview of the external I/O connectors of the IOBA-10F-AD.

3.3.1 9 V ~ 30 V DC Power Jack

Use the DC power jack to connect the system to a power source.

Figure 3-1: 9 V ~ 30 V DC Power Jack

3.3.2 AI Connectors (IOBA-10F-AD Only)

The IOBA-10F-AD model equips with three AI connectors in Grove interface. The pinouts
are shown below.

Pin Description

1 GND
2 IOT_AI-5V
3 IOT_A0/A2/A4
4 IOT_A1/A3/A5

Table 3-1: AI Connector (AI) Pinouts

3.3.3 Digital I/O Connectors (IOBA-10F-AD Only)

The IOBA-10F-AD model equips with two digital I/O connectors in Grove interface. The
pinouts are shown below.

Pin Description

1 GND
2 DIO_3V3
3 DIO_D5/D7
4 DIO_D6/D8

IOBA-10F-AD RISC-based Panel PC

Page 15

3.3.4 Digital I/O Terminal Block ( IOBA-10F-AD Only)

The IOBA-10F-AD model equips with one 6-pin digital I/O terminal block. The pinouts are
shown below.

Pin Description

1 VIO_3V3 (DIO1)
2 VIO_3V3 (DIO2)
3 GND
4 VIO_3V3 (DIO3)
5 VIO_3V3 (DIO4)
6 GND

Table 3-3: DIO Terminal Block (DIO1) Pinouts

3.3.5 I2C Connectors (IOBA-10F-AD Only)

The IOBA-10F-AD model equips with three I2C connectors in Grove interface. The pinouts
are shown below.

Pin Description

1 GND
2 IOT_3V3
3 SDA1_3V3
4 SCL1_3V3

Table 3-4: I2C Connector (I2C) Pinouts

3.3.6 microSD Card Slot

The system comes with a microSD card slot for install ation of a microSD card.

Figure 3-2: microSD Card Slot

IOBA-10F-AD RISC-based Panel PC

Page 16

3.3.7 RJ-45 LAN Connector

There is one RJ-45 LAN connector that allows conne ction t o a n ex t ernal n etwo rk. Besides,
the IOBA-10F-AD model equips with one additional RJ-45 LAN connector (Figure 1-3)
which supports PoE function. The RJ-45 LAN connector pinouts are shown below.

Pin Description

1 LAN_MDI[0]+
2 LAN_MDI[0]­3 LAN_MDI[1]+
4 LAN_MDI[1]­5 LAN_MDI[2]+
6 LAN_MDI[2]­7 LAN_MDI[3]+
8 LAN_MDI[3]-

Table 3-5: RJ-45 LAN Connector Pinouts

3.3.8 RS-232 Serial Interface (IOBA-10F-AD Only)

The IOBA-10F-AD model equips with one RS-232 connector in Grove interface. The
pinouts are shown below.

Pin Description

1 GND
2 VIO_3V3
3 RS232_TXD1
4 RS232_RXD1

Table 3-6: RS-232 Connector (UART2) Pinouts

IOBA-10F-AD RISC-based Panel PC

Page 17

3.3.9 RS-232/422/485 Serial Interface

The system has a 4-pin RS-232/422/485 t erminal block. Its pinouts are sho wn below.

Pin RS-232 RS-422 RS-485

1 TXD TX- N/A
2 RXD RX+ DATA+
3 N/A RX- DATA­4 N/A TX+ N/A

Table 3-7: RS-232/422/485 Terminal Block (UART1) Pinouts

3.3.10 USB 2.0 Host Connectors

The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices.

Figure 3-3: USB 2.0 Host Connector

3.4 Mounting the System

WARNING!

When mounting the panel PC, it is better t o have mor e than one perso n
to help with the installation to make sure the panel PC does not fall
down and get damaged.

To mount the IOBA-10F-AD onto the wall, please follow the steps below.

Step 1: Select the location on the wall for the wall-mounting bra cket .

Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.

IOBA-10F-AD RISC-based Panel PC

Page 18

Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention

screws.

Step 4: Align the wall-mounting bracket screw holes wit h the pilot holes.

Step 5: Secure the mounting bracket to the wall by inserting the retention screws into

the four pilot holes and tightening them (Figure 3-4 and Figure 3-5).

Figure 3-4: IOBA-10F-AD Wall-mounting Bracket

Figure 3-5: IOBA-10F-AD-ET Wall-mounting Bracket

IOBA-10F-AD RISC-based Panel PC

Page 19

NOTE:

In the following diagrams, the bracket is already installed on the wall.

Step 6: Insert the four mounting screws provided in the wall mounting kit into the four

screw holes on the mounting bracket and tighten until the screw shank is
secured (Figure 3-6).

Figure 3-6: Mounting Screws

Step 7: Align the mounting holes on the rear of the panel PC (Figure 3-7) with the

bracket mounting screws (Figure 3-6).

Figure 3-7: Panel PC Mounting Holes

IOBA-10F-AD RISC-based Panel PC

Page 20

Step 8: Carefully attach the panel P C to the mounting screws and gently pull the panel

PC upwards until the panel PC rests securely on screws (Figure 3-8). Ensure
that all four of the slotted holes fit snuggly int o their re spe ctiv e mount ing s crew s.

Figure 3-8: Securing to the Wall-Mounting Bracket

Step 9: Secure the panel PC by installing the two retention sc rews p rovided in the wall

mounting kit into the two screw holes on the bottom of the bracket (Figure 3-8).

Step 0:

3.5 System Maintenance

If the components of the IOBA-10F-AD fail, they must be replaced. Please contact the
system reseller or vendor to purchase the replacement parts.

NOTE:

A user cannot replace a motherboard. If the motherboard fails it must
be shipped back to IEI to be replaced. Please contact the system
vendor, reseller or an IEI sales person directly .

IOBA-10F-AD RISC-based Panel PC

Page 21

Chapter

4

4 Using the IOBA-10F-AD

IOBA-10F-AD RISC-based Panel PC

Page 22

4.1 Powering On/Off

 Powering On: To power on the system, connect the power source to the DC-in jack of

the IOBA-10F-AD (Figure 1-3 and Figure 1-4). The power LED on the front panel
(Figure 1-2) lights up once the system is f ed with power.

 Powering Off: To power off the system, disconnect the power source.

4.2 Home Screen

The IOBA-10F-AD has multiple home screens, allowing users to customize the screen
with widgets, apps and shortcuts. The following sections describe the basic technique to
manage the home screen.

4.2.1 Switching between Home Screens

Swipe left or right to switch between home screens.

Figure 4-1: Multiple Home Screens

IOBA-10F-AD RISC-based Panel PC

Page 23

4.2.2 Favorites Tray

The Favorites tray at the bottom of each home screen allows users to keep the most
important or frequently used shortcuts.

Tap the (APPS) button at the center of the Favorites Tray to access the APPS page.
Touch and hold an app icon and drag it to the Favorites tray or move it from the Favorites
tray.

Figure 4-2: Favorites Tray

4.2.3 Adding Shortcut

To add app or widget shortcuts on the home screen, follow the steps below.

Step 1: Click the APPS button on the home screen to access the APPS/WIDGETS page.

Step 2: Touch and hold an app icon or a widget (click the WIDGETS tab to access the

widgets page) and drag it to the home screen. Step 0:

IOBA-10F-AD RISC-based Panel PC

Page 24

Figure 4-3: APPS Page

4.2.4 Arranging the Home Screen

The items on the home screen can be moved and delet ed. Touch and hold an item on the
home screen and drag it where you want. To trash the item on the screen, drag it to the
Remove icon. Release the icon when it turns red.

Figure 4-4: Move and Trash Item on Home Screen

IOBA-10F-AD RISC-based Panel PC

Page 25

4.3 Navigation Buttons

The three navigation buttons shown in Figure 4-5 can always be found at the bottom of
every screen.

Figure 4-5: Navigation Buttons

Buttons Description
Back Tap to return to the previous screen.
Home Tap to return to the home screen.
Recent Apps Tap to display all the recently used applications.

Table 4-1: Navigation Buttons

IOBA-10F-AD RISC-based Panel PC

Page 26

4.4 Status Bar

The status bar on the top of the screen (Figure 4-6) displays the pending notifications and
status, such as the signal strength.

Figure 4-6: Status Bar

Swipe down from the status bar to view notification details (Figure 4-7). To dismiss a ll
notifications, tap the icon located at the very bottom of the noti fication list.

Figure 4-7: Pending Notification List

IOBA-10F-AD RISC-based Panel PC

Page 27

4.5 Settings

The Settings menu allows configuration to the IOBA-10F-AD, such as Wi-Fi, volume,
screen brightness, etc. To enter the Settings menu, tap Settings on the APPS page.

4.5.1 Wireless & networks

Figure 4-8: Wireless and Networks Settings

In the Wireless & networks field, the user can turn on/of f the Wi-Fi and Bluetooth function s,
configure the network settings, and view the data usage status.

 Wi-Fi:

Allows the user to turn on or off the Wi-Fi function and manage the access
points. The user can tap to configure advanced Wi-Fi settings.

 Bluetooth:

Allows the user to turn on or off the Bl uetooth function and manage the
Bluetooth connections.

 Ethernet:

Proceeds with Ethernet configuration.

 Data usage:

Allows the user to view data usage status.

IOBA-10F-AD RISC-based Panel PC

Page 28

4.5.1.1 More Settings

Figure 4-9: More Settings Menu

After tapping More… in the Wireless & networks field, the user can configure the following
settings.

 Airplane mode:

Allows the user to turn on or off the ai rplane mode.

 Default SMS app:

Allows the user to change the default SMS app.

 NFC:

Allows the user to turn on or off the NFC function.

 Android Beam:

This item is available only when the NFC function is turned on. Enabling this
feature allows the user to beam app content t o another NFC-capable device.

 Tethering & portable hotspot:

Allows the user to set this device as a portabl e Wi-Fi hotspot, configure the
hotspot settings and turn on or off the Bluetooth tethering function.

 VPN:

Sets up and manages Virtual Private Networks (VPNs).

IOBA-10F-AD RISC-based Panel PC

Page 29

4.5.2 Display

 Cellular networks:

Configures the cellular network settings.

 Mobile plan:

Sets up the cellular data service.

Figure 4-10: Display Menu

Use the Display menu to configure the following items.

 Brightness level:

Adjusts the screen brightness.

 Wallpaper:

Sets up the wallpaper.

 Sleep:

Sets up the time of inactivity after which the screen turns to sleep mode.

 Daydream:

Configures the screensaver settings.

 Font size:

Sets up the font size.

IOBA-10F-AD RISC-based Panel PC

Page 30

 When device is rotated:

Allows the user to select to rotate the contents of the screen when the
IOBA-10F-AD is rotated.

 Cast screen:

Allows the user to cast the IOBA-10F-AD screen to the nearby devices.

4.5.3 Sound & Notification

Figure 4-11: Sound & Notification Menu

Use the Sound & notification menu to configure the following items.

 Media volume/Alarm volume:

Adjusts the volume of alarms or media.

 Notification volume:

Adjusts the volume of notifications.

 Interruptions:

Configures the interruption settings.

 Default notification ringtone:

Sets up the notification ringtone.

 Other sounds:

Sets up the screen locking and touch so unds.

IOBA-10F-AD RISC-based Panel PC

Page 31

4.5.4 Storage

The Storage menu displays the status of the internal storage, the inserted microSD card
and the connected USB storage devices, and allows users to manage the data stored in
them.

 When device is locked:

Selects the notification display option when the device is locked.

 App notifications:

Configures the notification settings for an individual app.

 Notification access:

Enables or disables an app to read notification s.

Figure 4-12: Storage Menu

IOBA-10F-AD RISC-based Panel PC

Page 32

4.5.5 Apps

The Apps menu displays the applications installed in the device, and allows users to
manage them.

Figure 4-13: Apps Menu

4.5.6 Users

The Users menu allows the user to configure the owner information.

Figure 4-14: Users Menu

IOBA-10F-AD RISC-based Panel PC

Page 33

4.5.7 Location

Use the Location menu to turn on the location access function so t hat the apps can obtain
the user’s location information. When this function is turned on, the user can decide the
method to determine the user’s location.

Figure 4-15: Location Menu

4.5.8 Security

Figure 4-16: Security Menu

IOBA-10F-AD RISC-based Panel PC

Page 34

Use the Security menu to configure the following items.

 Screen lock:

Sets up the way to unlock the screen.

 Owner info:

Enables to show the information of the device owner on the lock screen.

 Encrypt tablet:

Once this item is enabled, the user will need to enter the numeric PIN,
password or pattern that have been set up to decrypt the IOBA-10F-AD each
time when powering on.

 Make passwords vi sible:

Enables to show password when typing.

 Device administrators:

Views or deactivates the device administrators.

 Unknown sources:

Enables to allow installation of applic ations from unknown sources.

 Storage type:

Displays the supported storage type.

 Trusted credentials:

Taps to display the CA certificates.

 Install from SD card:

Taps to install certificates from the microSD card.

 Clear credentials:

Taps to remove all certificates.

 Trust agents:

Taps to view or deactivate trust agents.

 Screen pinning:

When this function is turned on, the user can keep t he current screen in view
until the user disables this function.

 Apps with usage access:

Taps to manage the apps with usage access.

IOBA-10F-AD RISC-based Panel PC

Page 35

4.5.9 Accounts

Tap Add account to start setting up an e-mail or corporate account.

Figure 4-17: Accounts Menu

4.5.10 Language & Input

Figure 4-18: Language & Input Menu

Use the Language & input menu to configure the following items.

IOBA-10F-AD RISC-based Panel PC

Page 36

 Language:

Sets up the language for IOBA-10F-AD.

 Spell checker:

Allows the user to enable the spell checking function and to configure its
settings.

 Personal dictionary:

Configures the user dictionary.

 Keyboard & input methods:

Allows the user to set up the onscreen keyboard.

 Text-to-speech output:

Configures the text-to-speech settings.

 Pointer speed:

Sets up the pointer speed.

4.5.11 Backup & Reset

Figure 4-19: Backup & Reset Menu

Use the Backup & reset menu to configure the following items.

 Factory data reset:

Erases all data from the internal stor age of the IOBA-10F-AD.

IOBA-10F-AD RISC-based Panel PC

Page 37

4.5.12 Date & Time

Figure 4-20: Date & Time Menu

Use the Date & time menu to configure the following items.

 Automatic date & time:

Turns on to use the net work-provided time.

 Automatic time zone:

Turns on to use the net work-provided time zone.

 Set date:

Sets up the system date. This item is av ailable onl y when the Automatic date
& time item is disabled.

 Set time:

Sets up the system time. This item i s avail able only when the Automatic date
& time item is disabled.

 Select time zone:

Sets up the time zone.

 Use 24-hour format:

Turns on to use the 24-hour format.

IOBA-10F-AD RISC-based Panel PC

Page 38

4.5.13 Accessibility

Figure 4-21: Accessibility Menu

Use the Accessibility menu to configure the following items.

 Services:

Displays the accessibility services that have been installed.

 Captions:

Turns on/off the caption function and configures its settings.

 Magnification gestures:

Enables to zoom in and out by triple-tapping the screen.

 Large text:

Turns on to use large tex t .

 High contrast text:

Turns on to display tex t in high contrast level.

 Auto-rotate screen:

Turns on or off the auto-rotate function of the screen.

 Speak passwords:

Turns on or off the speak password function.

 Accessibility shortcut:

Turns on to allow the user to quickly enable the accessibility features.

IOBA-10F-AD RISC-based Panel PC

Page 39

4.5.14 Printing

The Printing menu allows managing the printing services installed on the IOBA-10F-AD.

 Text-to-speech output:

Configures the text-to-speech settings.

 Touch & hold delay:

Configures the touch & hold delay settings.

 Color inversion:

Turns on or off the color inversion function.

 Color correction:

Turns on or off the color correction function.

Figure 4-22: Printing Menu

IOBA-10F-AD RISC-based Panel PC

Page 40

Figure 4-23: About Tablet Menu

4.5.15 About Tablet

Use the About tablet menu to display the following items.

 Additional system updates:

Taps to update the syst em from OTA (over-the-air) or from the m icroSD card.

 Status:

Taps to display the status of batteries, network, signal, etc.

 Legal information:

Taps to display the legal i nformation.

 Model number:

Displays the model number.

 Android version:

Displays the Android version.

 Android security patch level:

Displays the Android security patch level.

 Baseband version:

Displays the baseband version.

 Kernel version:

Displays the kernal version.

 Build number:

Displays the device build number.

IOBA-10F-AD RISC-based Panel PC

Page 41

4.6 File Management

The IOBA-10F-AD provides a file management tool that allows users to manage files in
the internal storage and external storage devices. Tap ES File Explorer on t he applicati on
page to launch it.

Figure 4-24: ES File Explorer Screen

The user can tap the storage folder (Figure 4-24) to view all the possible storage devices
listed below.

 sdcard0: Internal storage of the IOBA-10F-AD
 sdcard1: SD card connected to the IOBA-10F-AD
 usb1: USB storage device connected to the USB host connector on the

bottom panel. Refer to Figure 1-3 for the connector location.

 usb2: USB storage device connected to the USB host connector on the

bottom panel. Refer to Figure 1-3 for the connector location.

IOBA-10F-AD RISC-based Panel PC

Page 42

Figure 4-25: Possible Storage Devices

Tap a storage device to display its contents if available.

IOBA-10F-AD RISC-based Panel PC

Page 43

Appendix

A

A Regulatory Compliance

IOBA-10F-AD RISC-based Panel PC

Page 44

has telecommunications functionality, it also complies with the

o

DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive 2004/108/EC
 Low-Voltage Directive 2006/95/EC
 RoHS II Directive 2011/65/EU

If the user modifies and/or install other devices in the equipment, the CE conformity
declaration may no longer apply.

If this equipment
requirements of the R&TTE Directive 1999/5/ E C.

English
IEI Integration Corp declares that this equi pm ent is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Български [Bulgarian]
IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива 1999/5/ЕС.
Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]
IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav
øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen
und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

Eesti [Estonian]
IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiiv ist tulenevatele teistele asjakohastele sätetele.

IOBA-10F-AD RISC-based Panel PC

Page 45

Español [Spanish]
IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicabl es o exigibles de la Directiva 1999/5/CE.
Ελληνική [Greek]
IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/ΕΚ.

Français [French]
IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]
IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed
alle altre disposizioni pertinenti stabi l i te dalla direttiva 1999/5/CE.
Latviski [Latvian]
IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 1999/5/EK.
Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

1999/5/EB Direktyvos nuostatas.
Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel i n overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richt l i jn 1999/5/EG.
Malti [Maltese]
IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar [Hungarian]
IEI Integration Corp nyilatkozom, hogy a beren dezés megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português [Portuguese]
IEI Integration Corp declara que este equipamento está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.

IOBA-10F-AD RISC-based Panel PC

Page 46

Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele
esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE.

Slovensko [Slovenian]
IEI Integration Corp izjavlja, da je t a opreme v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky

príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin m ui den ehtojen mukainen.
Svenska [Swedish]
IEI Integration Corp förklarar att denna utrustni ngstyp står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.

IOBA-10F-AD RISC-based Panel PC

Page 47

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this

frequency energy and, if not

FCC WARNING

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

 This device may not cause harmful interference, and
 This device must accept any interference receiv ed, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can

equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Federal Communication Commission Interference Statement

This equipment has been assembled with components that comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmf ul inte rferen ce in a residential installation.
This equipment generates, uses and can radiate radio
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there i s no guar a ntee t hat inter feren ce will n ot occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the followin g m easures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/ T V technician for help.

IOBA-10F-AD RISC-based Panel PC

Page 48

Appendix

B

B Safety Precautions

IOBA-10F-AD RISC-based Panel PC

Page 49

The precautions outlined in this chapter should be strictly followed.

WARNING:

Failure to follow these precautions may result in permanent damage to
the IOBA-10F-AD.

B.1 Safety Precautions

Please follow the safety precautions out l i ned in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the

IOBA-10F-AD is opened.

 Make sure the power is turned off and the power cord is disconnected

whenever the IOBA-10F-AD is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock.

 Electric shocks can occur if the IOBA-10F-AD chassis is opened when the

IOBA-10F-AD is running.

 Do not drop or insert any objects into the ventilation openings of the

IOBA-10F-AD.

 If considerable amounts of dust, water, or fluids enter the IOBA-10F-AD,

turn off the power supply immediately, unplug the power cord, and contact the
IOBA-10F-AD vendor.

 DO NOT:

o Drop the IOBA-10F-AD against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated t em perature

IOBA-10F-AD RISC-based Panel PC

Page 50

Failure to take ESD precautions during the installation of the

B.1.2 Anti-static Precautions

WARNING:

IOBA-10F-AD may result in permanent damage to the IOBA-10F-AD
and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IOBA-10F-AD. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the IOBA-10F-AD is opened and any of the electrical components
are handled, the following anti-static prec autions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component , touch any

grounded conducting material. During the t i m e the electrical component is
handled, frequently touch any conducting materials that are connected to the
ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an anti-static pad. This reduces the possibility of ESD
damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical component by its edges.

IOBA-10F-AD RISC-based Panel PC

Page 51

Risk of explosion if battery is replaced by an incorrect type. Only

B.1.3 Product Disposal

CAUTION:

certified engineers should replace the on-board bat tery.

Dispose of used batteries according to instructions and local
regulations.

 Outside the European Union - If you wish to dispose of used electrical and

electronic products out side the European Union, please contact your local
authority so as to comply with the correct dispo sal m ethod.

 Within the European Union:

EU-wide legislation, as implemented in each Member State, requires that
waste electrical and electronic products carrying the mark (left) must be
disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow
the guidance of your local authority, or ask the shop where you purchased the product.
The mark on electrical and electronic products only applie s to t he current Europ ean Unio n
Member States.

Please follow the national guidelines for elect rical and electronic product disposal.

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the IOBA-10F-AD, please follow the gui deli nes below.

B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the IOBA-10F-AD, please read the details
below.

IOBA-10F-AD RISC-based Panel PC

Page 52

 Except for the LCD panel, never spray or squirt liquids directly onto any other

components. To clean the LCD panel, gently wipe it with a piece of soft dry
cloth or a slightly moistened cloth.

 The interior of the IOBA-10F-AD does not require cleaning. Keep f luids away

from the IOBA-10F-AD interior.

 Be cautious of all small removable components when vacuuming the

IOBA-10F-AD.

 Turn the IOBA-10F-AD of f before cleaning the IOBA-10F-AD.
 Never drop any objects or liquids through the openings of the IOBA-10F-AD.
 Be cautious of any possible allergic reactions t o solvents or chemicals used

when cleaning the IOBA-10F-AD.

 Avoid eating, drinking and smoking within vicinity of the IOBA-10F-AD.

B.2.2 Cleaning Tools

Some components in the IOBA-10F-AD may only be cleaned using a product specifically
designed for the purpose. In such case, the product will be explicitly mentioned in the
cleaning tips. Below is a list of items to use when cleaning the IOBA-10F-AD.

 Cloth – Alt hough p aper towel s or tissu es can be us ed, a sof t, cle an piece of

cloth is recommended when cleaning the IOBA-10F-AD.

 Water or rubbing alcohol – A clot h m oistened with water or rubbing alcohol

can be used to clean the IOBA-10F-AD.

 Using solvents – T he use of s olvent s is not recomm ended when clea ning the

IOBA-10F-AD as they may damage the plastic parts.

 Vacuum cleaner – U sing a vacuum specifically designed for computers is

one of the best methods of cleaning the IOBA-10F-AD. Dust and dirt can
restrict the airflow in the IOBA-10F-AD and cause its circuitry to corrode.

 Cotton swabs - Cotton swaps moistened wit h rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

IOBA-10F-AD RISC-based Panel PC

Page 53

Appendix

C

C Hazardous Materials

Disclosure

IOBA-10F-AD RISC-based Panel PC

Page 54

The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain material s in the product, and is applicable to China
RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.

Please refer to below table.

Part Name Toxic or Hazardous Substances and Elements

Lead
(Pb)

Housing
Display
Printed Circuit
Board
Metal Fasteners
Cable Assembly
Fan Assembly
Power Supply
Assemblies
Battery
O: T h is toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the lim it

requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homo geneous materials for this part is above

O O O O O O
O O O O O O
O O O O O O

O O O O O O
O O O O O O
O O O O O O
O O O O O O

O O O O O O

Mercury
(Hg)

Cadmium
(Cd)

Hexavalent
Chromium
(CR(VI))

Polybrominated
Biphenyls
(PBB)

Polybrominated
Diphenyl Ethers
(PBDE)

the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

IOBA-10F-AD RISC-based Panel PC

Page 55

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称

壳体
显示
印刷电路板
金属螺帽
电缆组装
风扇组装
电力供应组装
电池

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(CR(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O
O O O O O O

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 (现由 GB/T 26572-2011 取代)
标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 (现由 GB/T 26572-2011

取代) 标准规定的限量要求。