IEI Technology INOX-F15C-ULT3 User Manual

Download

Page 1

INOX-F15C-ULT3 Stainless Panel PC

Page I

MODEL:

Stainless Steel Panel PC with Intel® Core™ i5-6300U /

INOX-F15C-ULT3

Rev. 1.00 - January 18, 2018

Celeron® 3955U CPU, Touch screen, USB 2.0, Dual GbE LAN,

RS-232/422/485, IP 69K Front Panel and RoHS

User Manual

Page 2

INOX-F15C-ULT3 Stainless Panel PC

Page II

Date Version Changes

January 18, 2018 1.00 Initial release

Revision

Page 3

INOX-F15C-ULT3 Stainless Panel PC

Page III

Warning! To prevent the system from overheating, do not operate it in an area that

Safety Instructions

Warning! Read the user manual before connecting the system to the power

source.

Vorsicht! Bitte lesen Sie die Bedienungsanleitung, bevor Sie das System an eine

Stromquelle anschließen.

Attention! Avant de brancher le système à la source d'alimentation, consultez le

mode d'emploi.

Avvertenza! Consultare il manuale utente prima di collegare il sistema all'alimentatore. Atención! Lea atentamente este manual del usuario antes de operar la fuente de alimentación.

警告！在將系統連接到電源之前，請仔細閱讀使用手冊。

警告！在将系统连接到电源之前，请仔细阅读使用手册。

exceeds the maximum operating temperature described in the user manual.

Vorsicht! Um eine Überhitzung des Systems zu vermeiden, betreiben Sie es ausschließlich im zulässigen Betriebstemperaturbereich. Dieser ist in der Bedienungsanleitung vermerkt.

Attention! Pour éviter la surchauffe du système, ne l'utilisez pas dans une zone

dont la température dépasse les limites décrits dans le mode d'emploi.

Avvertenza! Per evitare che il sistema si surriscaldi, non utilizzarlo in aree che

superino la temperatura massima d'esercizio descritta nel manuale utente.

Atención! Para evitar el excesivo calentamiento del sistema, no opere en las

condiciones de temperatura superior a lo recomendado en este manual del usuario.

警告！為防止系統過熱，不要在使用手冊上記載的產品工作溫度範圍之外操作此系

統。

警告！为防止系统过热，不要在使用手册上记载的产品工作温度范围之外操作此系

统。

Page 4

INOX-F15C-ULT3 Stainless Panel PC

Page IV

源适配器将可能导致火灾或爆炸。电源适配器规格请参考使用手册。

Warning! Use only the adapter and power cord approved for this system. Use of

another type of adapter may risk fire or explosion. Please refer to the user manual

for the power adapter specifications. Vorsicht! Nur zugelassene Netzteile und Netzkabel dürfen verwendet werden. Die Benutzung von anderen Netzteilen kann einen Brand oder eine Explosion zur Folge haben. Prüfen Sie die jeweiligen Spezifikationen in der Bedienungsanleitung. Attention! Utilisez exclusivement le câble d'alimentation et l’adaptateur

homologués pour ce système. L’utilisation d’un autre type d’adaptateur risquerait

de provoquer un incendie ou une explosion. Veuillez référer au mode d'emploi

pour les spécifications de l'adaptateur d'alimentation. Avvertenza! Utilizzare solo l'adattatore e il cavo di alimentazione approvati per

questo sistema. L'uso di un altro tipo di adattatore può causare rischio d'incendio

o esplosione. Si prega di fare riferimento al manuale utente per le specifiche

sull'alimentazione. Atención! Utilice solamente el adaptador de corriente alterna (CA) con Marcas

Conformidad otorgadas. Cualquier otro adaptador no otorgado aumenta el riesgo

de explosión o incendio. Por favor consulte el manual del usuario para las

especificaciones del adaptador de alimentación.

警告！只能使用經過認證、適用於本系統的電源變壓器與電源線。使用不適用的電

源變壓器將可能導致火災或爆炸。電源變壓器規格請參考使用手冊。

警告！只能使用经过认证，适用于本系统的电源适配器与电源线。使用不适用的电

Warning! Ultimate disposal of this product should be handled according to all

national laws and regulations.

Vorsicht! Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und

Gesetzen des Landes erfolgen.

Attention! La mise au rebut ou le recyclage de ce produit sont généralement soumis aux lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.

Avvertenza! Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e i regolamenti locali. Atención! La disposición final de residuos de este producto se debe cumplir con las normativas y leyes del país.

警告！本產品的廢棄處理應根據該國家的法律和規章進行。

警告！本产品的废弃处理应根据该国家的法律和规章进行。

Page 5

INOX-F15C-ULT3 Stainless Panel PC

Page V

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibil ity of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

Page 6

INOX-F15C-ULT3 Stainless Panel PC

Page VI

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously.

CAUTION

Cautionary messages should be heeded to help red uce the chance of losing data or damaging the product.

NOTE

These messages inform the reader of essent ial but non-critical information. These messages should be read carefully as any directions or instructions contained therein ca n help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that shoul d not be touched without taking care.

Page 7

INOX-F15C-ULT3 Stainless Panel PC

Page VII

Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1 OVERVIEW .................................................................................................................. 2

1.2 MODEL VARIATIONS ................................................................................................... 3

1.3 FEATURES ................................................................................................................... 3

1.4 FRONT PANEL ............................................................................................................. 4

1.5 REAR PANEL ............................................................................................................... 5

1.6 SYSTEM SPECIFICATIONS ............................................................................................ 6

1.7 DIMENSIONS ............................................................................................................... 8

2 UNPACKING ................................................................................................................. 9

2.1 UNPACKING .............................................................................................................. 10

2.2 PACKING LIST ........................................................................................................... 10

2.3 OPTIONAL ITEMS ...................................................................................................... 12

3 INSTALLATION ......................................................................................................... 14

3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 15

3.2 INSTALLATION PRECAUTIONS ................................................................................... 15

3.3 HDD INSTALLATION ................................................................................................. 16

3.4 EXTERNAL I/O CONNECTORS ................................................................................... 18

3.4.1 COM Port Connection ..................................................................................... 18

3.4.2 LAN Port Connection ....................................................................................... 20

3.4.3 USB Port Connection ....................................................................................... 21

3.4.3.1 Ferrite Core Installation ............................................................................ 21

3.4.4 Power Input Connection .................................................................................. 23

3.5 MOUNTING THE SYSTEM .......................................................................................... 24

3.6 POWERING ON THE SYSTEM ..................................................................................... 25

3.7 SYSTEM MAINTENANCE ........................................................................................... 26

3.8 SOFTWARE INSTALLATION ........................................................................................ 26

3.9 INSTALLING WINDOWS 7 FROM USB 3.0 DRIVES ..................................................... 27

4 BIOS SETUP ................................................................................................................ 28

Page 8

INOX-F15C-ULT3 Stainless Panel PC

Page VIII

4.1 INTRODUCTION ......................................................................................................... 29

4.1.1 Starting Setup ................................................................................................... 29

4.1.2 Using Setup ...................................................................................................... 29

4.1.3 Getting Help ..................................................................................................... 30

4.1.4 BIOS Menu Bar ................................................................................................ 30

4.2 MAIN ........................................................................................................................ 31

4.3 ADVANCED ............................................................................................................... 32

4.3.1 ACPI Settings ................................................................................................... 33

4.3.2 F81866 Super IO Configuration ...................................................................... 34

4.3.2.1 Serial Port n Configuration ....................................................................... 34

4.3.2.1.1 Serial Port 1 Configuration ................................................................ 35

4.3.2.1.2 Serial Port 2 Configuration ................................................................ 36

4.3.3 F81866 H/W Monitor ....................................................................................... 37

4.3.4 RTC Wake Settings ........................................................................................... 38

4.3.5 Serial Port Console Redirection ...................................................................... 39

4.3.5.1 Legacy Console Redirection Settings ....................................................... 40

4.3.5.2 Console Redirection Settings .................................................................... 41

4.3.6 CPU Configuration .......................................................................................... 43

4.3.7 SATA Configuration ......................................................................................... 45

4.3.8 USB Configuration ........................................................................................... 47

4.3.9 IEI Feature ....................................................................................................... 48

4.4 CHIPSET ................................................................................................................... 49

4.4.1 System Agent (SA) Configuration .................................................................... 49

4.4.1.1 Graphics Configuration ............................................................................. 50

4.4.1.1.1 LCD Control ...................................................................................... 52

4.4.1.2 Memory Configuration ............................................................................. 53

4.4.2 PCH-IO Configuration .................................................................................... 53

4.4.2.1 PCI Express Configuration ....................................................................... 54

4.5 SECURITY ................................................................................................................. 55

4.6 BOOT ........................................................................................................................ 56

4.7 EXIT ......................................................................................................................... 58

A REGULATORY COMPLIANCE .............................................................................. 60

B SAFETY PRECAUTIONS ......................................................................................... 66

B.1 SAFETY PRECAUTIONS ............................................................................................. 67

Page 9

INOX-F15C-ULT3 Stainless Panel PC

Page IX

B.1.1 General Safety Precautions ............................................................................. 67

B.1.2 Anti-static Precautions .................................................................................... 68

B.1.3 Product Disposal ............................................................................................. 69

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 70

B.2.1 Maintenance and Cleaning .............................................................................. 70

B.2.2 Cleaning T ools ................................................................................................. 70

C BIOS MENU OPTIONS ............................................................................................. 72

D WATCHDOG TIMER ................................................................................................ 75

E HAZARDOUS MATERIALS DISCLOSURE ......................................................... 78

Page 10

INOX-F15C-ULT3 Stainless Panel PC

Page X

List of Figures

Figure 1-1: INOX-F15C-ULT3 Stainless Steel Panel PC .............................................................. 2

Figure 1-2: Front View .................................................................................................................... 4

Figure 1-3: Rear Panel .................................................................................................................... 5

Figure 1-4: Dimensions (mm) ........................................................................................................ 8

Figure 3-1: HDD Panel Retention Screws .................................................................................. 16

Figure 3-2: HDD Installation ........................................................................................................ 17

Figure 3-3: RS-232/422/485 Connector (COM1, COM2) ............................................................. 18

Figure 3-4: DB-9 COM Port Cable ............................................................................................... 19

Figure 3-5: LAN Connector .......................................................................................................... 20

Figure 3-6: RJ-45 LAN Cable ....................................................................................................... 20

Figure 3-7: USB 2.0 Connector .................................................................................................... 21

Figure 3-8: Open Ferrite Core ...................................................................................................... 22

Figure 3-9: Wrapping Cable around the Core ............................................................................ 22

Figure 3-10: Cable Installed with Ferrite Core ........................................................................... 22

Figure 3-11: Power Input Connector ........................................................................................... 23

Figure 3-12: VESA Mounting Retention Screw Holes ............................................................... 24

Figure 3-14: Powering On the System ........................................................................................ 25

Figure 3-13: Terminal Block Pinouts of Power Cable ............................................................... 25

Page 11

INOX-F15C-ULT3 Stainless Panel PC

Page XI

List of Tables

Table 1-1: Model Variations ........................................................................................................... 3

Table 1-2: System Specifications .................................................................................................. 7

Table 3-1: RS-232/422/485 Connector Pinouts .......................................................................... 18

Table 3-2: RS-232/422/485 Serial Port Pinouts .......................................................................... 19

Table 3-3: LAN Connector Pinouts ............................................................................................. 20

Table 3-4: USB 2.0 Connector Pinouts ....................................................................................... 21

Table 3-5: Power Input Connector Pinouts ................................................................................ 23

Page 12

INOX-F15C-ULT3 Stainless Panel PC

Page XII

List of BIOS Menus

BIOS Menu 1: Main ....................................................................................................................... 31

BIOS Menu 2: Advanced .............................................................................................................. 32

BIOS Menu 3: ACPI Settings ....................................................................................................... 33

BIOS Menu 4: F81866 Super IO Configuration .......................................................................... 34

BIOS Menu 5: Serial Port n Configuration ................................................................................. 34

BIOS Menu 6: F81866 H/W Monitor ............................................................................................. 37

BIOS Menu 7: RTC Wake Settings .............................................................................................. 38

BIOS Menu 8: Serial Port Console Redirection ......................................................................... 39

BIOS Menu 9: Legacy Console Redirection Settings ............................................................... 40

BIOS Menu 10: Console Redirection Settings ........................................................................... 41

BIOS Menu 11: CPU Configuration ............................................................................................. 43

BIOS Menu 12: SATA Configuration ........................................................................................... 45

BIOS Menu 13: USB Configuration ............................................................................................. 47

BIOS Menu 14: IEI Feature ........................................................................................................... 48

BIOS Menu 15: Chipset ................................................................................................................ 49

BIOS Menu 16: System Agent (SA) Configuration .................................................................... 49

BIOS Menu 17: Graphics Configuration ..................................................................................... 50

BIOS Menu 18: LCD Control ........................................................................................................ 52

BIOS Menu 19: Memory Configuration ....................................................................................... 53

BIOS Menu 20: PCH-IO Configuration ........................................................................................ 53

BIOS Menu 21: PCI Express Configuration ............................................................................... 54

BIOS Menu 22: Security ............................................................................................................... 55

BIOS Menu 23: Boot ..................................................................................................................... 56

BIOS Menu 24: Exit ....................................................................................................................... 58

Page 13

INOX-F15C-ULT3 Stainless Panel PC

Page 1

Chapter

1 Introduction

Page 14

INOX-F15C-ULT3 Stainless Panel PC

Page 2

1.1 Overview

Figure 1-1: INOX-F15C-ULT3 Stainless Steel Panel PC

The INOX-F15C-ULT3 series is a quad-core Intel 3955U powered stainless steel panel PC wit h a ri ch v ariety of functions and peripherals.

The stainless steel design and the IP69K compliant front panel make the INOX-F15C-ULT3 an ideal system for use in high temperature, high pressure environment.

The Intel optimal memory, graphics, and peripheral I/O support. The system comes with 4.0 GB of DDR4 SO-DIMM memory ensuring smooth data throughputs with reduced bottlenecks and fast system access.

Multiple M12 connectors ensure simplified connectivity to a variety of external peripheral devices, including two GbE LAN, two RS-232/422/485 and four USB 2.0.

Core™ i5-6300U / Celeron® 3955U is a System-on-Chip (SoC) that ensures

Core™ i5-6300U or Intel® Celeron®

Page 15

INOX-F15C-ULT3 Stainless Panel PC

Page 3

1.2 Model Variations

There are several models in the INOX-F15C-ULT3 series. The mod el numbe rs and model variations are listed below.

Model Size Processor Touchscreen INOX-F15C-ULT3-C/R/4G

INOX-F15C-ULT3-C/PC/4G

INOX-F15C-ULT3-i5/R/4G

INOX-F15C-ULT3-i5/PC/4G

Table 1-1: Model Variations

1.3 Features

The INOX-F15C-ULT3 features are listed below:

 15” LCD with LED backlight  IP69K compliant front panel for high temperature, high pressure wash-down

 Intel  Preinstalled with 4 GB of DDR4 memory (system max. 32 GB)  SUS304 stainless steel housing

15” Intel® Celeron® 3955U Resistive type

15” Intel® Celeron® 3955U Projected capacitive type

15”

applications

Core™ i5-6300U or Intel® Celeron® 3955U processor

Intel® Core™ i5-6300U

Resistive type

Projected capacitive type

 Resistive type or projected capacitive type touchscreen  Fanless design  Easy-access HDD bay  Multiple M12 connectors provide various I/O connections, including two GbE

LAN, two RS-232/422/485 and four USB 2.0

 9 V–36 V wide range DC power input

Page 16

INOX-F15C-ULT3 Stainless Panel PC

Page 4

1.4 Front Panel

The front side of the INOX-F15C-ULT3 is a panel with a TFT LCD touchscreen surrounded by a stainless steel frame (Figure 1-2). The front panel is IP69K compliant to withstand high temperature and high pressure wash-down.

Figure 1-2: Front View

Page 17

INOX-F15C-ULT3 Stainless Panel PC

Page 5

1.5 Rear Panel

The rear panel of the INOX-F15C-ULT3 has the following connectors and switches. The rear panel also provides access for installing a 2.5” SATA SSD.

Figure 1-3: Rear Panel

Page 18

INOX-F15C-ULT3 Stainless Panel PC

Page 6

1.6 System Specifications

The technical specifications for the INOX-F15C-ULT3 systems are listed in Table 1-2.

Specification INOX-F15C-ULT3 LCD Size

Max. Resolution

Brightness (cd/m2)

Contrast Ratio

LCD Color

Pixel Pitch (H x V) (mm)

Viewing Angle (H-V)

Backlight MTBF

Backlight

Touchscreen

CPU (SoC)

Memory

15"

1024 (W) x 768 (H)

450

800:1

16.2M

0.297 x 0.297

160° / 150°

70,000 hrs

LED

Resistive type / Projected capacitive type

Intel® Core™ i5-6300U or Intel® Celeron® 3955U

Two 260-pin 2133/1867 MHz dual-channel DDR4 SO-DIMM slots

Ethernet

Storage

Expansions

Construction Material

preinstalled with 4 GB SDRAM (system max. 32 GB)

Two Intel® I210 PCIe GbE controllers

1 x 2.5” SATA 6Gb/s SSD bay

1 x Full-size PCIe Mini card slot (SATA 6Gb/s) 1 x Full-size/half-size PCIe Mini card slot (PCIe x1 and USB 2.0

signals) 1 x M.2 B-key slot (for M.2 2242/2260/2280, supporting USB 3.0,

PCIe x2 and SAT A signals)

SUS304 stainless steel housing

Page 19

INOX-F15C-ULT3 Stainless Panel PC

Page 7

Thermal Design

VESA Mount

Net/Gross Weight

Dimensions (W x H x D)

Operating Temperature

Storage Temperature

Humidity

IP Level

Safety/EMC

Power Supply

Input:

Fanless

100 mm x 100 mm (with M4 screws)

6.9 kg / 9.8 kg

414.0 mm x 328.4 mm x 51.9 mm

-20ºC ~ 50ºC

-20ºC ~ 60ºC

10% ~ 95% (non-condensing)

Front panel: IP69K Others: IP66

CE, FCC Class A

100 W power adapter (optional)

100 V ~ 240 V AC, 50 Hz ~ 60 Hz

Output:

Power Requirement

Power Consumption

I/O Ports and Switches

Table 1-2: System Specifications

12 V DC, 8.34 A

9 V ~ 36 V DC

50 W, 9 ~ 36 V 5.5 ~ 1.4 A

2 x RS-232/422/485 serial port (8-pin M12 connector)

2 x GbE LAN (8-pin M12 X-Coded connector)

2 x USB 2.0 connector (8-pin M12 connector, each supports two USB ports)

1 x 9 V ~ 36 V DC input jack (5-pin M12 connector)

1 x Power switch with power LED indicator

1 x Pressure relief valve

Page 20

INOX-F15C-ULT3 Stainless Panel PC

Page 8

1.7 Dimensions

The dimensions of the INOX-F15C-ULT3 are shown below.

Figure 1-4: Dimensions (mm)

Page 21

INOX-F15C-ULT3 Stainless Panel PC

Page 9

Chapter

2 Unpacking

Page 22

INOX-F15C-ULT3 Stainless Panel PC

Page 10

The front side LCD screen has a protective plastic cover stuck to the

installed. This ensures the screen is protected during the installation

If any of the components listed in the checklist below are missing, do not

the installation. Contact the IEI reseller or vendor the

was purchased from or contact an IEI sales representative

2.1 Unpacking

To unpack the panel PC, follow the steps below:

WARNING!

screen. Only remove the plastic cove r after the panel PC has be en properly

process.

Step 1: Carefully cut the tape sealing the box. Only cut deep enough to break the tape.

Step 2: Open the outside box.

Step 3: Carefully cut the tape sealing the box. Only cut deep enough to break the tape.

Step 4: Open the inside box.

Step 5: Lift the panel PC out of the boxes.

Step 6: Remove the peripheral parts box from the main box. Step 0:

2.2 Packing List

NOTE:

proceed with INOX-F15C-ULT3 directly by sending an email to sales@ieiworld.com.

Page 23

INOX-F15C-ULT3 Stainless Panel PC

Page 11

The INOX-F15C-ULT3 panel PC is shipped with the following components:

Quantity Item Image

1 INOX-F15C-ULT3 panel PC

1 Power cable

USB cable

Ferrite core for USB cable

Flat-head screw (M3*5)

8 Pan-head screw (6#32*8) with Nylok

1 Touch Pen (resistive type only)

Page 24

INOX-F15C-ULT3 Stainless Panel PC

Page 12

1 Utility CD

1 One Key Recovery CD

2.3 Optional Items

The following are optional components which may be separately purchased:

NOTE:

It is recommended that each M12 cable should be installed with a ferrite core to reduce EMI. Therefore, be sure to pur chase a fer rite core fo r the M12 c able to be purchased. The optional M12 cables include USB cable, RJ-45 LAN cable and DB-9 COM port cable.

Item and Part Number Image

USB cable (P/N: 32001-001000-100-RS or 32001-001000-300-RS)

RJ-45 LAN cable (P/N: 32013-003200-100-RS)

Page 25

INOX-F15C-ULT3 Stainless Panel PC

Page 13

Item and Part Number Image

DB-9 COM port cable (P/N: 32005-000100-100-RS or

32005-000100-300-RS)

Ferrite core (P/N: 30600-000058-RS)

Waterproof power adapter (100 W) (P/N: 63040-030080-000-RS)

Arm (P/N: ARM-31-RS)

Stand for VESA 100 (P/N: STAND-A19-RS)

Stand for VESA 75/VESA 100 (P/N: STAN D -C19-R10)

If any of these items are missing or damaged, contact the distributor or sales representative immediately.

Page 26

INOX-F15C-ULT3 Stainless Panel PC

Page 14

3 Installation

Chapter

Page 27

INOX-F15C-ULT3 Stainless Panel PC

Page 15

Failure to take ESD precautions during the maintenance of the

to the

3.1 Anti-static Precautions

WARNING:

INOX-F15C-ULT3 may result in permanent damage INOX-F15C-ULT3 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the INOX-F15C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the INOX-F15C-ULT3 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-st atic wristband can

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, f requently touch any conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the INOX-F15C-ULT3, place it on

an anti-static pad. This reduces the possibility of ESD damaging the INOX-F15C-ULT3.

 Only handle the edges of the PCB: When handling the PCB, hold the PCB

by the edges.

3.2 Installation Precautions

When installing the panel PC, please follow the precautions listed below:

 Power turned off: When installing the panel PC, make sure the power is off.

Failing to turn off the power may cause severe injury to the body and/or damage to the system.

 Certified Engineers: Only certified engineers should install and modify

onboard functionalities.

Page 28

INOX-F15C-ULT3 Stainless Panel PC

Page 16

 Anti-static Discharge: If a user open the rear panel of the panel PC, to

configure the jumpers or plug in added peripheral dev ices, ground themselves first and wear an anti-static wristband.

3.3 HDD Installation

To install the HDD into the system, plea se follow the steps below:

Step 1: Remove the HDD panel located on the rear panel by removing the eight

retention screws.

Figure 3-1: HDD Panel Retention Screws

Step 2: The HDD bracket for installing HDD is located on the bottom side of the HDD

panel. Attach an HDD to the HDD bracket. To do this, align the four retention screw holes on the both sides of the HDD with the retention screw holes in the HDD brackets. Insert four M3*5 retention screws shipped with the package into the HDD bracket (Figure 3-2).

Step 3: Connect the pre-installed SATA cable from the INOX-F15C-ULT3 to the rear of

the HDD (Figure 3-2).

Page 29

INOX-F15C-ULT3 Stainless Panel PC

Page 17

Figure 3-2: HDD Installation

Step 4: Install the HDD panel back to the rear panel of the INOX-F15C-ULT3 by using

the 6#32*8 retention screws with Nylok shipped with the package, and a tightening torque of 5 kg-cm (4.3 lb-in/0.49 N-m). Step 0:

WARNING:

To ensure the system is completely waterti ght, the HDD panel retention screws with Nylok must be used and tightened to 5 kg-cm (4.3 lb-in /

0.49 N-m).

Page 30

INOX-F15C-ULT3 Stainless Panel PC

Page 18

3.4 External I/O Connectors

The INOX-F15C-ULT3 is equipped with several M12 connectors for I/O interface connection. These M12 connectors are all protected with metal/plastic dust caps. Please remove the dust cap before connection.

3.4.1 COM Port Connection

The INOX-F15C-ULT3 has two 8-pin M12 connectors for RS-232/422/485 serial port connection. The pinouts for the RS-232/422/485 connectors are listed in the figure and table below.

Figure 3-3: RS-232/422/485 Connector (COM1, COM2)

PIN NO. DESCRIPTION

1 DCD 2 SIN+ 3 SOUT 4 DTR 5 GND 6 DSR 7 RTS 8 CTS

Table 3-1: RS-232/422/485 Connector Pinouts

Page 31

INOX-F15C-ULT3 Stainless Panel PC

Page 19

[Optional Choice]

The DB-9 COM port cable (Figure 3-4) can be purchased separately. The user can use the cable to connect the INOX-F15C-ULT3 with serial devices. The COM port cable should be installed with a f errite core to reduce EMI. To install the ferrite core, pl ease refe r to Section 3.4.3.1.

Figure 3-4: DB-9 COM Port Cable

The DB-9 connector pinouts of the COM port cable are listed below.

PIN NO. RS-232 RS-422 RS-485

1 DCD TXD422- TXD4852 RXD TXD422+ TXD485+ 3 TXD RXD422+ -4 DTR RXD422- -5 GND -- -6 DSR -- -7 RTS -- -8 CTS -- -9 -- -- --

Table 3-2: RS-232/422/485 Serial Port Pinouts

Page 32

INOX-F15C-ULT3 Stainless Panel PC

Page 20

3.4.2 LAN Port Connection

The INOX-F15C-ULT3 has two 8-pin M12 X-Coded connectors for GbE LAN connection. The pinouts for the LAN connectors are listed in t he figure and table below.

Figure 3-5: LAN Connector

PIN NO. DESCRIPTION

1 2 3 4 5 6 7 8

P0 N0 P1 N1 P3 N3 N2 P2

Table 3-3: LAN Connector Pinouts

The RJ-45 LAN cable (Figure 3-4) can be purchased separately. The user can use the cable to connect the INOX-F15C-ULT3 with network. The LAN cable should be installed with a ferrite core to reduce EMI. To install the ferrite cor e, please ref er to Section 3.4.3.1.

Figure 3-6: RJ-45 LAN Cable

Page 33

INOX-F15C-ULT3 Stainless Panel PC

Page 21

3.4.3 USB Port Connection

The INOX-F15C-ULT3 has two 8-pin M12 connectors for USB 2.0 connection. Each M12 connector supports two USB 2.0 ports connection. The pinouts for the USB 2.0 connectors are listed in the figure and table below.

Figure 3-7: USB 2.0 Connector

PIN NO. DESCRIPTION

1 USB POWER 2 SUSB POWER 3 24 2+ 5 GND 6 1+ 7 18 GND

Table 3-4: USB 2.0 Connector Pinouts

3.4.3.1 Ferrite Core Installation

An USB c able is shipped with the INOX-F15C-ULT3. The USB cable should be installed with a ferrite core to reduce EMI. To install the ferrite core, f ol low the steps below.

Step 1: Open the ferrite core by unsnapping the latch.

Page 34

INOX-F15C-ULT3 Stainless Panel PC

Page 22

Figure 3-8: Open Ferrite Core

Step 2: Gently wrap the USB cable around the ferrite core. The USB cable should pass

through the core twice as shown below. The ferrite core must be installed as close to the M12 connector as possible.

Figure 3-9: Wrapping Cable around the Core

Step 3: Close the ferrite core and snap the latch back together. Then, pull both ends of

the cable in opposite direction to tighten the loop.

Figure 3-10: Cable Installed with Ferrite Core

Page 35

INOX-F15C-ULT3 Stainless Panel PC

Page 23

3.4.4 Power Input Connection

The INOX-F15C-ULT3 has one 5-pin M12 connector that supports 9 V ~ 36 V power input connection. The pinouts for the power input connector are listed in the figure and table below.

Figure 3-11: Power Input Connector

PIN NO. DESCRIPTION

1 DC IN 2 DC IN 3 GND 4 GND 5 GND

Table 3-5: Power Input Connector Pinouts

Page 36

INOX-F15C-ULT3 Stainless Panel PC

Page 24

please ensure that it is VESA

it cannot be used to support the

3.5 Mounting the System

The INOX-F15C-ULT3 is VESA (Video Electronics Standards Association) compliant and can be mounted on a mounting device with a 100 mm interface pad. The INOX-F15C-ULT3 VESA mount retention screw holes are shown in Figure 3-12. Refer to the installation guide that came with the mounting device to mount the INOX-F15C-ULT3.

Figure 3-12: VESA Mounting Retention Screw Holes

NOTE:

When purchasing the mounting device, compliant and that the device has a 100 mm interface pad. If the mounting device is not VESA compliant, INOX-F15C-ULT3 panel PC.

Page 37

INOX-F15C-ULT3 Stainless Panel PC

Page 25

3.6 Powering On the System

Figure 3-13: Powering On the System

To power on the system, follow the steps below:

Step 1: Connect the M12 connector of the power cable to the INOX-F15C-ULT3.

Connect the terminal block of the power cable to a power source. The terminal block pinouts are shown below.

Figure 3-14: Terminal Block Pinouts of Power Cable

Step 2: Locate the power button on the rear panel.

Step 3: Short press the power button to power up the system. Once power ed up, the

power LED on the power button turns on in blue. Step 0:

Page 38

INOX-F15C-ULT3 Stainless Panel PC

Page 26

or contact

3.7 System Maintenance

It is suggested not to remove the rear cover to access the system internally. If any internal components of the INOX-F15C-ULT3 fail, please contact the system reseller or vendor to ship the system back to IEI for repai r.

NOTE:

A user cannot replace a motherboard. If the motherboard fails it must be shipped back to IEI to be replaced. Please contact the system vendor, reseller or an IEI sales person directly .

3.8 Software Installation

NOTE:

The content of the CD may vary throughout the life cycl e of the produ ct and is subject to change without prior notice. Visit the IEI website technical support for the latest updates.

All the drivers for the INOX-F15C-ULT3 are on the utility CD that came with the system. The utility CD contains drivers for Wind o ws 8.1 (64-bit) and Windows 10 (64-bit) operating systems. If the drivers are not installed automatically, please install the following drivers manually.

 Chipset  VGA  LAN  Intel  ME (Intel

Serial IO

AMT)

 Touchscreen

Page 39

INOX-F15C-ULT3 Stainless Panel PC

Page 27

3.9 Installing Windows 7 from USB 3.0 Drives

Microsoft Windows 7 installation media does not include nat ive driver support for USB 3.0, so during installation, a keyboard/mouse connected to a USB 3.0 port does not respond. The Windows 7 USB 3.0 Creator Utility automates the steps to update a Windows 7 installation image so that it contains USB 3.0 drivers. To install Windows 7 from a USB drive onto the INOX-F15C-ULT3, please follow the steps described below.

Step 1: Create a USB flash drive installer. Use your Windows 7 DVD or ISO image to

create a bootable USB flash drive. Instru ct i ons on how to do are found on

Microsoft’s website

Step 2: Download and unzip the Windows 7 US B 3.0 Creator utility to a temporary folder

on the Admin system.

Step 3: Connect the USB device containing the Windows 7 image to the Admin sy st em.

Step 4: Right-click the file “Installer_Creator.exe” and select Run as administrato r.

Step 5: Browse to the root of the USB drive.

Step 6: Click “Create Image” to begin the creation process.

Step 7: Wait for the process to finish. It can take up to 15 minutes.

Step 8: Using the updated installer, proceed with the Windows 7 installation as you

normally would.

Page 40

INOX-F15C-ULT3 Stainless Panel PC

Page 28

Chapter

4 BIOS Setup

Page 41

INOX-F15C-ULT3 Stainless Panel PC

Page 29

4.1 Introduction

The BIOS is programmed onto the BIOS chip. The BI OS setup pro gram allows changes to certain system settings. This chapter outli nes t he options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice .

4.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

1. Press the D

2. Press the D appears on the screen. 0.

If the message disappears before the D and try again.

ELETE or F2 key as soon as the system is turned on or ELETE or F2 key when the “Press Del to enter SETUP” message

ELETE or F2 key is pressed, restart the computer

4.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and PageDown keys to change entries, press F1 for help and press E keys are shown in.

Key Function

Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left hand side

SC to quit. Navigation

Right arrow Move to the item on the right hand side + Increase the numeric value or make changes

Page 42

INOX-F15C-ULT3 Stainless Panel PC

Page 30

Key Function

- Decrease the numeric value or make change s F1 key General help, only for Status Page Setup Menu and Option

F2 key Load previous values. F3 key Load optimized defaults F4 key Save changes and Exit BIOS Esc key Main Menu – Quit and not save changes into CMOS

4.1.3 Getting Help

Page Setup Menu

St atus Page Setup Menu and Option Page Setup Menu -Exit current page and return to M ai n M enu

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To ex it the Help Window press E the F1 key again.

4.1.4 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.  Advanced – Changes the advanced system settings.  Chipset – Changes the chipset settings.  Security – Sets User and Supervisor Passwords.  Boot – Changes the system boot configuration.  Save & Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu

SC or

items at the top of the BIOS screen and listed above.

Page 43

INOX-F15C-ULT3 Stainless Panel PC

Page 31

Main

Advanced

Chipset

Security

Boot

Save & Exit

BIOS Information

System Time [00:18:35]

4.2 Main

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.

BIOS Vendor American Megatrends Core Version 5.11 Compliency UEFI 2.4; PI 1.3 Project Version Z358AR10.ROM Build Date and Time 03/30/2017 13:50:45

Processor Information Name SkyLake Brand String Intel(R) Core(TM)

i5-6300U CPU @ 2.40GHz Frequency 2300 MHz Processor ID 406E3 Stepping D0/K0 Number of Processors 2Core(s) / 4Thread(s) Microcode Revision 7C GT Info GT2

IGFX VBIOS Version 1040 Memory RC Version 1.9.0.0 Total Memory 4096 MB Memoery Frequency 2133 MHz

PCH Information Name SKL PCH-LP PCH SKU PCH-LP Mobile (U)

Stepping 21/C1 LAN PHY Revision N/A

ME FW Version 11.0.0.1202 ME Firmware SKU Corporate SKU

SPI Clock Frequency D0FR Support Unsupported Read Status Clock Frequency 17 MHz Write Status Clock Frequency 17 MHz Fast Read Status Clock Frequency 17 MHz

System Date [Fri 01/01/2010]

Premium SKU

Set the Date. Use Tab to switch between Data elements.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 1: Main

The System Overview field also has two user configurable fields:

Page 44

INOX-F15C-ULT3 Stainless Panel PC

Page 32

Main

Advanced

Chipset

Security

Boot

Save & Exit

 System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and year.

 System Time [xx :xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

4.3 Advanced

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

> ACPI Settings > F81866 Super IO Configuration > F81866 H/W Monitor > RTC Wake Settings > Serial Port Console Redirection > CPU Configuration > SATA Configuration > USB Configuration > iEi Feature

System ACPI Parameters.

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

BIOS Menu 2: Advanced

Page 45

INOX-F15C-ULT3 Stainless Panel PC

Page 33

Advanced

Select the highest ACPI

ESC: Exit

3 (Suspend to

the RAM is maintained. The

computer returns slower to a working state, but

4.3.1 ACPI Settings

The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options.

ACPI Settings

ACPI Sleep State [S3 (Suspend to RAM]

sleep state the system will enter when the SUSPEND button is pressed.

----------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

 ACPI Sleep State [S3 (Suspend to RAM)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.

BIOS Menu 3: ACPI Settings



S RAM)

DEFAULT

The caches are flushed and the CPU is powered off. Power to

more power is saved.

Page 46

INOX-F15C-ULT3 Stainless Panel PC

Page 34

Advanced

ESC Exit

4.3.2 F81866 Super IO Configuration

Use the F81866 Super IO Configuration menu (BIOS Menu 4) to set or change the configurations for the serial ports.

F81866 Super IO Configuration

Super IO Chip F81866

> Serial Port 1 Configuration > Serial Port 2 Configuration

BIOS Menu 4: F81866 Super IO Configuration

4.3.2.1 Serial Port n Configuration

Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.

Set Parameters of Serial Port 1 (COMA)

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

Serial Port 1 Configuration

Serial Port [Enabled]

Device Settings IO=3F8h; IRQ=4

Change Settings [Auto] Device Mode [RS232]

BIOS Menu 5: Serial Port n Configuration

Enable or Disable Serial Port (COM)

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

Page 47

INOX-F15C-ULT3 Stainless Panel PC

Page 35

IO=3F8h; IRQ=3,

IO=2F8h; IRQ=3,

8h; IRQ=3,

4.3.2.1.1 Serial Port 1 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled



Enabled DEFAULT

 Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.



Auto DEFAULT



IO=3F8h; IRQ=4



4,5,6,7,9,10,11,12



4,5,6,7,9,10,11,12

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 3F8h and the interrupt address is IRQ4

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12



IO=3E 4,5,6,7,9,10,11,12



IO=2E 4,5,6,7,9,10,11,12

Serial Port I/O port address is 3 E8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Serial Port I/O port address is 2E8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Page 48

INOX-F15C-ULT3 Stainless Panel PC

Page 36

IO=3F8h; IRQ=3,

IO=2F8h; IRQ=3,

8h; IRQ=3,

 Device Mode [RS232]

Use the Device Mode option to select the Serial Port 1 signaling mode.



RS422



RS232 DEFAULT



RS485

4.3.2.1.2 Serial Port 2 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled



Enabled DEFAULT

 Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt

Serial Port 1 signaling mode is RS-422 Serial Port 1 signaling mode is RS-232 Serial Port 1 signaling mode is RS-485

Disable the serial port Enable the serial port

address.



Auto DEFAULT



IO=2F8h; IRQ=3



4,5,6,7,9,10,11,12



4,5,6,7,9,10,11,12



IO=3E 4,5,6,7,9,10,11,12



IO=2E 4,5,6,7,9,10,11,12

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Serial Port I/O port address is 3E8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Serial Port I/O port address is 2E8h and the interrupt address is IRQ3,4,5,6,7,9,10,11,12

Page 49

INOX-F15C-ULT3 Stainless Panel PC

Page 37

Advanced

ESC Exit

 Device Mode [RS232]

Use the Device Mode option to select the Serial Port 2 signaling mode.



RS422



RS232 DEFAULT



RS485

4.3.3 F81866 H/W Monitor

The F81866 H/W Monitor menu (BIOS Menu 6) contai ns the f an conf igur ation s ubmen us and displays operating temperature, fan speeds and system voltages.

PC Health Status

CPU temperature :+32 °C System temperature :+32 °C

CPU_CORE :+0.880 V +5V :+5.045 V +12V :+12.056 V +DDR :1.184 V +3.3V :+3.296 V +3.3VSB :+3.280 V +5VSB :+4.968 V

Serial Port 2 signaling mode is RS-422 Serial Port 2 signaling mode is RS-232 Serial Port 2 signaling mode is RS-485

Smart Fan Mode Select

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit

BIOS Menu 6: F81866 H/W Monitor

 PC Health Status

The following system parameters and values are shown. The system parameters that are monitored are:

 System T emperat ures:

o CPU Temperature

Page 50

INOX-F15C-ULT3 Stainless Panel PC

Page 38

Advanced

ESC Exit

o System temperature

 Voltages

o CPU_CORE o +5V o +12V o +DDR o +3.3V o +3.3VSB o +5VSB

4.3.4 RTC Wake Settings

The RTC Wake Settings menu (BIOS Menu 7) conf igure s RTC wake event .

Wake system with Fixed Time [Disabled]

BIOS Menu 7: RTC Wake Settings

 Wake system with Fixed Time [Disabled]

Use the Wake system with Fixed Time option to enable or disable the system wake on

Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec specified

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

alarm event.



Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake

Page 51

INOX-F15C-ULT3 Stainless Panel PC

Page 39

every day at the specified time. Besides, the

appear with values that can be

After setting the alarm, the computer turns itself on

Advanced

ESC Exit

event



Enabled

If selected, the Wake up every day option appears allowing you to enable to disable the sy st em t o wake

following options selected:

Wake up date Wake up hour Wake up minute Wake up second

from a suspend state when the alarm g oes off.

4.3.5 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 8) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and te xt output through the serial port.

COM1

Console Redirection [Disabled]

> Console Redirection Settings

COM2

Console Redirection [Disabled]

> Console Redirection Settings

Legacy Console Redirection

> Legacy Console Redirection Settings

BIOS Menu 8: Serial Port Console Redirection

Console Redirection Enable or Disable

--------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

Page 52

INOX-F15C-ULT3 Stainless Panel PC

Page 40

Advanced

 Console Redirection [Disabled]

Use Console Redirection option to enable or disable the con sole redirection function.



Disabled DEFAULT



Enabled

Disabled the console redirection function Enabled the console redirection function

4.3.5.1 Legacy Console Redirection Settings

The Legacy Console Redirection Settings menu (BIOS Menu 9) allows the legacy console redirection options to be configured.

Legacy Serial Redirection Port [COM1]

Select a COM port to display redirection of Legacy OS and Legacy OPROM Messages

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

BIOS Menu 9: Legacy Console Redirection Settings

 Legacy Serial Redirection Port [COM1]

Use the Legacy Serial Redirection Port option to specify a COM port to display redirection of legacy OS and legacy OPROM mes sages. The options include:

 COM1 D  COM2  COM3 (Pci Bus0, Dev0, Func0) (Disabled)

EFAULT

Page 53

INOX-F15C-ULT3 Stainless Panel PC

Page 41

Advanced

port color, function

Unicode chars onto 1 or

4.3.5.2 Console Redirection Settings

The Console Redirection Settings menu (BIOS Menu 10) allows the console redirection options to be configured. The option is activ e when Console Redirection option is enabled.

COM1 Console Redirection Settings

Terminal Type [ANSI] Bits per second [115200] Data Bits [8] Parity [None] Stop Bits [1]

BIOS Menu 10: Console Redirection Settings

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to sup keys, etc. VT-UTF8: Uses UTF8 encoding to map

more bytes.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

 Terminal Ty pe [ANSI]

Use the Terminal Type option to specify the remote termi nal type.



VT100



VT100+



VT-UTF8



ANSI DEFAULT

The target terminal type is VT100 The target terminal type is VT100+ The target terminal type is VT-UTF8 The target terminal type is ANSI

Page 54

INOX-F15C-ULT3 Stainless Panel PC

Page 42

This option does not

 Bits per second [115200]

Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds.



9600



19200



57600



115200 DEFAULT

 Data Bits [8]

Use the Data Bits option to specify the number of data bits.



8 DEFAULT

 Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors.

Sets the serial port transmission speed at 9600. Sets the serial port transmission speed at 19200. Sets the serial port transmission speed at 57600. Sets the serial port transmission speed at 115200.

Sets the data bits at 7. Sets the data bits at 8.



None DEFAULT



Even



Odd



Mark



Space

No parity bit is sent with the data bits. The parity bit is 0 if the number of ones in the data

bits is even. The parity bit is 0 if the number of ones in the data

bits is odd. The parity bit is always 1.

provide error detection. The parity bit is always 0.

provide error detection.

Page 55

INOX-F15C-ULT3 Stainless Panel PC

Page 43

Advanced

and Linux (OS optimized

ESC Exit

 Stop Bit s [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.

4.3.6 CPU Configuration

Use the CPU Configuration menu (BIOS Menu 11) to view detailed CPU specifications and configure the CPU.

CPU Configuration

Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz CPU Signature 406E3 Microcode Patch 7C Max CPU Speed 2400 MHz Min CPU Speed 400 MHz CPU Speed 2300 MHz Processor Cores 2 Hyper Threading Technology Supported Intel VT-x Technology Supported Intel SMX Technology Supported 64-bit Supported EIST Technology Supported

L1 Data Cache 32 KB x 2 L1 Code Cache 32 KB x 2 L2 Cache 256 KB x 2 L3 Cache 3 MB

Hyper-Threading [Enabled] Active Processor Cores [All] Intel Virtualization Technology [Disabled] Intel(R) SpeedStep(tm) [Enabled] CPU C states [Disabled]



1 DEFAULT



Sets the number of stop bit s at 1. Sets the number of stop bit s at 2.

Enabled for Windows XP

for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

BIOS Menu 11: CPU Configuration

Page 56

INOX-F15C-ULT3 Stainless Panel PC

Page 44

 Hyper Threading Function [Enabled]

Use the Hyper Threading function to enable or disable the CPU hyper threading function.



Disabled



Enabled DEFAULT

Disables the use of hyper threading technology Enables the use of hyper threading technology

 Active Processor Cores [All]

Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package.



All DEFAULT



 Intel

Use the Intel

Virtualization Technology [Disabled]

Virtualization Technology option to enable or disable virtualizat ion on the

system. When combined with third party software, Intel

Enable all cores in the processor packag e. Enable one core in the processor packa ge.

Virtualization technology allows

several OSs to run on the same system at the same time.

 

 Intel

Use the Intel Technology.

 

Disabled DEFAULT

Enabled

SpeedStep™ [Enabled]

SpeedStep™ option to enable or disable the Intel® SpeedStep

Disabled

Enabled DEFAULT

Disables Intel Enables Intel

Virtualization Technology.

Disables the Intel Enables the Intel

SpeedStep Technology.

Page 57

INOX-F15C-ULT3 Stainless Panel PC

Page 45

Advanced

ESC Exit

 CPU C St ate [Disabled]

Use the CPU C State option to enable or disable CPU C state.



Disabled DEFAULT



Enabled

Disables CPU C state. Enables CPU C state.

4.3.7 SATA Configuration

Use the SATA Configuration menu (BIOS Menu 12) to change and/or set the configuration of the SATA devices installed in the sy stem.

STAT Controller(s) [Enabled] SATA Mode Selection [AHCI]

SATA1 Empty

Hot Plug [Disabled]

mSATA(M_SATA1) Empty

Hot Plug [Disabled]

mSATA(M_2_BKEY1) Empty

Hot Plug [Disabled]

Enable or disable SATA Device

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

BIOS Menu 12: SATA Configuration

 STAT Controller(s) [Enabled]

Use the STAT Controller(s) option to enable or disable t he SATA device.



Enabled DEFAULT



Disabled

Enables the SATA device. Disables the SATA device.

Page 58

INOX-F15C-ULT3 Stainless Panel PC

Page 46

Before accessing the RAID configuration utility, ensure to set the

. This is to allow the “Press <CTRL+I> to enter Configuration

Utility……” message to appear during POST. Press Ctrl+I when

 SATA Mode Selection [AHCI]

Use the SATA Mode Selection option to configure SATA devices as AHCI devices.



AHCI DEFAULT



RAID

NOTE:

Option ROM Messages BIOS option in the Boot menu to Force BIOS

prompted to enter the RAID configuration utility.

 Hot Plug [Disabled]

Use the Hot Plug option to enable or disable the SATA device hot plug.

Configures SATA devices as AHCI device. Configures SATA devices as RAID device.



Disabled DEFAULT



Enabled

Disables the SATA device hot plug. Enables the SATA device hot plug

Page 59

INOX-F15C-ULT3 Stainless Panel PC

Page 47

Advanced

disables legacy support

ESC Exit

4.3.8 USB Configuration

Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information and configure the USB settings.

USB Configuration

USB Controllers: 1 XHCI USB Devices: 1 Keyboard, 1 Mouse, 1 Point

Legacy USB Support [Enabled]

BIOS Menu 13: USB Configuration

 USB Devices

Enables Legacy USB support. AUTO option

if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

The USB Devices Enabled field lists the USB devices that are enabled on the system

 Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enable d, any a t tached USB m ouse o r US B key board does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.

Page 60

INOX-F15C-ULT3 Stainless Panel PC

Page 48

Advanced

crashes. Please install

service before enabling

ESC Exit



Enabled DEFAULT



Disabled



Auto

Legacy USB support enabled Legacy USB support disabled Legacy USB support disabled if no USB devices are

connected

4.3.9 IEI Feature

Use the IEI Feature menu (BIOS Menu 14) to configure One Key Recovery function.

iEi Feature

Auto Recovery Function [Disabled]

Auto Recovery Function Reboot and recover system automatically within 10 min, when OS

Auto Recovery API

this function

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

 Auto Recovery Function [Disabled]

Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery.

BIOS Menu 14: IEI Feature



Disabled DEFAULT



Enabled

Auto recovery function disabled Auto recovery function enabled

Page 61

INOX-F15C-ULT3 Stainless Panel PC

Page 49

Main

Advanced

Chipset

Security

Boot

Save & Exit

Chipset

4.4 Chipset

Use the Chipset menu (BIOS Menu 15) to configure the system chipset.

> System Agent (SA) Configuration > PCH-IO Configuration

BIOS Menu 15: Chipset

4.4.1 System Agent (SA) Configuration

Use the System Agent (SA) Configuration menu (BIOS Menu 16) to configure the System Agent (SA) parameters.

System Agent (SA) Parameters

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

VT-d [Disabled]

> Graphics Configuration > Memory Configuration

BIOS Menu 16: System Agent (SA) Configuration

VT-d capability

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

Page 62

INOX-F15C-ULT3 Stainless Panel PC

Page 50

Chipset

ESC Exit

 VT-d [Disabled]

Use the VT-d option to enable or disable VT-d support .



Disabled DEFAULT



Enabled

Disable VT-d sup port. Enable VT-d support.

4.4.1.1 Graphics Configuration

Use the Graphics Configuration menu (BIOS Menu 17) to configure the graphics settings.

Graphics Configuration

Primary Display [Auto] Internal Graphics [Enabled] DVMT Pre-Allocated [256M] DVMT Total Gfx Mem [MAX] > LCD Control

Select which of Auto/IGFX/PCIE Graphics device should be Primary Display Or select SG for Switchable Gfx.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit

BIOS Menu 17: Graphics Configuration

 Primary Display [Auto]

Use the Primary Display option to select the graphics controller used as the primary boot device. Configuration options are listed bel ow:

 Auto D  IGFX  PCIE

EFAULT

Page 63

INOX-F15C-ULT3 Stainless Panel PC

Page 51

The internal graphics device is automatically detected

the internal graphics device. The following

appear with values that can be

 Internal Graphics [Enabled]

Use the Internal Graphics option to enable or disable the i nternal graphics device.



Auto

and enabled.



Disabled



Enabled DEFAULT

 DVMT Pre-Allocated [256M]

Use the DVMT Pre-Allocated option to set the amount of system mem ory alloc ated to t he integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system. Configuration options are listed below:

 32M  64M

Disable the internal graphics device. Enable

options/submenu selected:

DVMT Pre-Allocated DVMT Total Gfx Mem LCD Control

 128M  256M D  512M

 DVMT Total Gfx Mem [MAX]

Use the DVMT Total Gfx Mem option to select DVMT 5.0 total graphic memory size used by the internal graphics device. The following opt ions are available:

 128M  256M  MAX D

EFAULT

Page 64

INOX-F15C-ULT3 Stainless Panel PC

Page 52

Chipset

Select the Video Device which will be activated

ESC: Exit

4.4.1.1.1 LCD Control

Use the LCD Control submenu (BIOS Menu 18) to select a display device which will be activated during POST.

LCD Control

Primary IGFX Boot Display [VBIOS Default]

during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

 Primary IGFX Boot Display [VBIOS Default]

Use the Primary IGFX Boot Display option to select the display device used by the system when it boots.

BIOS Menu 18: LCD Control

 VBIOS Default  DP1  LVDS

DEFAULT

Page 65

INOX-F15C-ULT3 Stainless Panel PC

Page 53

Chipset

applied after

ESC Exit

4.4.1.2 Memory Configuration

Use the Memory Configuration submenu (BIOS Menu 19) to display the memory information.

Memory Information

Total Memory 4096 MB DIMM1 Not Present DIMM2 4096 MB

BIOS Menu 19: Memory Configuration

4.4.2 PCH-IO Configuration

Use the PCH-IO Configuration menu (BIOS Menu 20) to configure the PCH-IO chipset.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

Auto Power Button Status [Disable (ATX)]

Restore AC Power Loss [Last State]

> PCI Express Configuration

BIOS Menu 20: PCH-IO Configuration

Select AC power state when power is rea power failure.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit

Page 66

INOX-F15C-ULT3 Stainless Panel PC

Page 54

Chipset

 Restore AC Power Loss [Last State]

Use the Restore AC Power BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.



Power Off



Power On



Last State DEFAULT

4.4.2.1 PCI Express Configuration

Use the PCI Express Configuration submenu (BIOS Menu 21) to configure the PCI Express slots.

PCI Express Configuration

> M_2_BKEY1 > M_PCIE1

The system remains turned of f The system turns on The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

M_2_BKEY1 Settings.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 21: PCI Express Configuration

The PCIe slot submenus all contain the following options:

 PCIe Speed [Auto]

Use the PCIe Speed option to configure the PCIe interface speed.

 Auto D  Gen 1

EFAULT

Page 67

INOX-F15C-ULT3 Stainless Panel PC

Page 55

Main

Advanced

Chipset

Security

Boot

Save & Exit

 Gen 2  Gen 3

 Detect Non-Compliance Device [Disabled]

Use the Detect Non-Compliance Device option to enable or disable detecting if a non-compliance PCI Express device is connected t o the PCI Express slot.



Disabled DEFAULT



Enabled

Disables to detect if a non-compliance PCI Express device is connected to the PCI Express slot.

Enables to detect if a non-compliance PCI Express device is connected to the PCI Express slot.

4.5 Security

Use the Security menu (BIOS Menu 22) to set system and user passwords.

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be: Minimum length 3 Maximum length 20

Administrator Password User Password

Set Administrator Password

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

BIOS Menu 22: Security

Page 68

INOX-F15C-ULT3 Stainless Panel PC

Page 56

Main

Advanced

Chipset

Security

Boot

Save & Exit

Allows the Number Lock on the keyboard to be

boots up. This allows the immediate use of the

the keyboard. To confirm this, the Number Lock LED

 Administrator Password

Use the Administrator Password to set or change a administrator password.

 User Password

Use the User Password to set or change a user password.

4.6 Boot

Use the Boot menu (BIOS Menu 23) to configure system boot options.

Boot Configuration

Bootup NumLock State [On] Quiet Boot [Enabled] UEFI Boot [Disabled]

Driver Option Priorities

Launch PXE OpROM [Disabled] Option ROM Messages [Force BIOS]

Boot Option Priorities

BIOS Menu 23: Boot

 Bootup NumLock State [On]

Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up.



On DEFAULT

Select the keyboard NumLock state

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

enabled automatically when the computer system

10-key numeric keypad located on the right side of

light on the keyboard is lit.

Page 69

INOX-F15C-ULT3 Stainless Panel PC

Page 57

Does not enable the keyboard Number Lock

press the Number Lock key located on the upper

key pad. The Number

Lock LED on the keyboard lights up when the



Off

 Quiet Boot [Enabled]

Use the Quiet Boot BIOS option to select the screen display when the system boots.

automatically. To use the 10-keys on the keyboard,

left-hand corner of the 10-

Number Lock is engaged.



Disabled



Enabled DEFAULT

 UEFI Boot [Disabled]

Use the UEFI Boot option to enable or disable to boot f rom the UEFI devices.



Enabled



Disabled DEFAULT

 Launch PXE OpROM [Disabled]

Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.



Disabled DEFAULT



Enabled

Normal POST messages displayed OEM Logo displayed instead of POST m essages

Boot from UEFI devices is enabled. Boot from UEFI devices is disabled.

Ignore all PXE Option ROMs Load PXE Option ROMs.

 Option ROM Messages [Force BIOS ]

Use the Option ROM Messages option to set the Option ROM display mode.



Force BIOS

DEFAULT

Sets display mode to force BIOS.

Page 70

INOX-F15C-ULT3 Stainless Panel PC

Page 58

Main

Advanced

Chipset

Security

Boot

Save & Exit

ESC Exit



Keep Current

 Boot Option Priority

Use the Boot Option Priority function to set the system boot sequence from the available devices. The drive sequence also depends on the boot sequence in the individual device section.

4.7 Exit

Use the Exit menu (BIOS Menu 24) to load default BIOS values, optimal failsafe values and to save configuration changes.

Save Changes and Reset Discard Changes and Reset

Restore Defaults Save as User Defaults Restore User Defaults

Sets display mode to current.

Reset the system after saving the changes.

---------------------



↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

: Select Screen

BIOS Menu 24: Exit

 Save Changes and Reset

Use the Save Changes and Reset option to save the changes made to the BIOS options and to exit the BIOS configuration setup program.

Page 71

INOX-F15C-ULT3 Stainless Panel PC

Page 59

 Discard Changes and Reset

Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program.

 Restore Defaults

Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this op eration.

 Save as User Defaults

Use the Save as User Defaults option to save the changes done so far as user defaults.

 Restore User Defaults

Use the Restore User Defaults option to restore t he user defaul ts to all t he setup option s.

Page 72

INOX-F15C-ULT3 Stainless Panel PC

Page 60

Appendix

A Regulatory Compliance

Page 73

INOX-F15C-ULT3 Stainless Panel PC

Page 61

f the user modifies and/or install other devices in the equipment, the CE conformity

has telecommunications functionality, it also complies with the

IEI Integration Corp erklærer herved, at f øl gende udstyr overholder de væsentlige krav o

DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive (2004/108/EC, 2014/30/EU)  Low-Voltage Directive (2006/95/EC, 2014/35/EU)  RoHS II Directive (2011/65/EU, 2015/863/EU)

I declaration may no longer apply.

If this equipment requirements of the Radio Equipment Directive 2014/53/EU.

English IEI Integration Corp declares that this equi pm ent is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Български [Bulgarian] IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива 2014/53/EU Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 2014/53/EU.

Dansk [Danish]

øvrige relevante krav i direktiv 2014/53/ E U. Deutsch [German] IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 2014/53/EU. Eesti [Estonian] IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 2014/53/EÜ põhinõuetele ja nimetatud direktiiv ist tulenevatele teistele asjakohastele sätetele.

Page 74

INOX-F15C-ULT3 Stainless Panel PC

Page 62

Español [Spanish] IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicabl es o exigibles de la Directiva 2014/53/EU. Ελληνική [Greek] IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU.

Français [French] IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU.

Italiano [Italian] IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabi l i te dalla direttiva 2014/53/EU. Latviski [Latvian] IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 2014/53/EU. Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

2014/53/EU Direktyvos nuostatas. Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel i n overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richt l i jn 2014/53/EU. Malti [Maltese] IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU.

Magyar [Hungarian] IEI Integration Corp nyilatkozom, hogy a beren dezés megfelel a vonatkozó alapvetõ követelményeknek és az 2014/53/EU irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU.

Português [Portuguese] IEI Integration Corp declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU.

Page 75

INOX-F15C-ULT3 Stainless Panel PC

Page 63

Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele esenţiale şi cu celelalte prevederi relevante ale Directivei 2014/53/EU.

Slovensko [Slovenian] IEI Integration Corp izjavlja, da je t a opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU.

Slovensky [Slovak] IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 2014/53/EU.

Suomi [Finnish] IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 2014/53/EU oleellisten vaatimusten ja sitä koskevien direktiivin m ui den ehtojen mukainen. Svenska [Swedish] IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 2014/53/EU.

Page 76

INOX-F15C-ULT3 Stainless Panel PC

Page 64

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

es, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this

frequency energy and, if not

this equipment does cause harmful interference to radio or

FCC WARNING

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

 This device may not cause harmful interference, and  This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, us

equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Federal Communication Commission Interference Statement

This equipment has been assembled with components that comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limit s are desi gned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio installed and used in accordance with th e instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the followin g m easures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from t hat to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Page 77

INOX-F15C-ULT3 Stainless Panel PC

Page 65

out or undergo abrupt change.” This product may contain replaceable

CHINA ROHS

The label on the product indicates the estimated “Environmentally Friendly Use Period” (EFUP). This is an estimate of the numbe r of years t hat these substances would “not leak

sub-assemblies/components which have a shorter EFUP such as batteries and lamps. These components will be separately marked.

Page 78

INOX-F15C-ULT3 Stainless Panel PC

Page 66

Appendix

B Safety Precautions

Page 79

INOX-F15C-ULT3 Stainless Panel PC

Page 67

The precautions outlined in this chapter should be strictly followed.

WARNING:

Failure to follow these precautions may result in permanent damage to the INOX-F15C-ULT3.

B.1 Safety Precautions

Please follow the safety precautions out l i ned i n the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precaution s are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the device is

opened.

 Make sure the power is turned off and the power cord is disconnected

whenever the INOX-F15C-ULT3 is being installed, moved or modified.

 To prevent the risk of electric shock, make sure power cor d is

unplugged from wall socket. To fully disengage the power to the unit,

please disconnect the power cord from the AC outlet. Refer servicing to qualified service personnel. The AC outlet shall be readily available and accessible.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock. Use a power cord that matches the voltage of the power out l et, which has been approved and complies with the safety standard of your particular country.

 Electric shocks can occur if the INOX-F15C-ULT3 chassis is opened when

it is running. To avoid risk of electric shock, this device must only be connected to a supply mains with protective earth.

 Do not drop or insert any objects into the ventilation openings of the

INOX-F15C-ULT3.

Page 80

INOX-F15C-ULT3 Stainless Panel PC

Page 68

Failure to take ESD precautions during the installation of the

may result in permanent damage to the

 If considerable amounts of dust, water, or fluids enter the device, turn off

the power supply immediately, unplug the power cord, and contact the INOX-F15C-ULT3 vendor.

 DO NOT:

o Drop the device against a hard surface. o Strike or exert excessive force onto the LCD panel . o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds t he rated temperature

B.1.2 Anti-static Precautions

WARNING:

INOX-F15C-ULT3 INOX-F15C-ULT3 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the INOX-F15C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the INOX-F15C-ULT3 is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-st atic wristband can

help to prevent ESD from damaging any electrical com ponent.

 Self-grounding: Before handling any electrical component, touch any

grounded conducting material. During the t im e the electrical component is handled, frequently touch any conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an anti-static pad. This reduces the possibility of ESD damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical c om ponent by its edges.

Page 81

INOX-F15C-ULT3 Stainless Panel PC

Page 69

Dispose of used batteries according to instructions and local

B.1.3 Product Disposal

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

regulations.

 Outside the European Union–If you wish to dispose of used electrical an d

electronic products out side the European Union, please contact your local authority so as to comply with the correct dispo sal m ethod.

 Within the European Union–The device that produces less waste and is

easier to recycle is classified as electronic device in terms of the E uropean Directive 2012/19/EU (WEEE), and must not be disposed of as domestic garbage.

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product. The mark on electrical and electronic products only applies t o the curre nt E uropean Union Member States.

Please follow the national guidelines for elect rical and electronic product disposal.

Page 82

INOX-F15C-ULT3 Stainless Panel PC

Page 70

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the INOX-F15C-ULT3, please follow the guidelines below.

WARNING:

 For safety reasons, turn-off the power and unplug the panel PC

before cleaning.

 If you dropped any material or liquid such as water onto the panel

PC when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable.

B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the INOX-F15C-ULT3, please read the details below.

 Except for the LCD panel, never spray or squirt liquids directly onto any other

components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened cloth.

 The interior of the device does not require cleaning. Keep fluids aw ay from the

device interior.

 Be cautious of all small removable components when vacuuming the device.  Never drop any objects or liquids through the openings of the device.  Be cautious of any possible allergic reactions to solvents or chemicals us ed

when cleaning the device.

 Avoid eating, drinking and smoking within vicinity of the device.

B.2.2 Cleaning Tools

Some components in the INOX-F15C-ULT3 may only be cleaned using a product specifically designed for the purpose. In such case, the produ ct will be explicitly mentioned in the cleaning tips. Below is a list of items to use wh en cleaning the INOX-F15C-ULT3.

 Cloth– Although paper towels or tissues can be used, a soft, clean piece of

cloth is recommended when cleaning the device.

Page 83

INOX-F15C-ULT3 Stainless Panel PC

Page 71

 Water or rubbing alcohol–A cloth moistene d with water or rubbing alcohol

can be used to clean the device.

 Using solvents–The use of solvents is not recommended when cleaning the

device as they may damage the plastic parts.

 Vacuum cleaner–Using a vacuum specifically designed for computers is

one of the best methods of cleaning the device. Dust and dirt can restrict the airflow in the device and cause its cir cuitry to corrode.

 Cotton swabs–Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs–Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

Page 84

INOX-F15C-ULT3 Stainless Panel PC

Page 72

Appendix

C BIOS Menu Options

Page 85

INOX-F15C-ULT3 Stainless Panel PC

Page 73



System Date [xx/xx/xx] ........................................................................................................ 32

System T ime [xx:xx:xx] ....................................................................................................... 32

ACPI Sleep State [S3 (Suspend to RAM)] .......................................................................... 33

Serial P ort [ Enabled] ............................................................................................................ 35

Change Settings [Auto] ....................................................................................................... 35

Devi ce M od e [RS232] ........................................................................................................... 36

Serial P ort [ Enabled] ............................................................................................................ 36

Change Settings [Auto] ....................................................................................................... 36

Devi ce M od e [RS232] ........................................................................................................... 37

PC Health Status .................................................................................................................. 37

Wake system with Fixed Time [Disabled] .......................................................................... 38

Console Redirection [Disabled] ......................................................................................... 40

Legacy Serial Redirec tion Port [COM1] ............................................................................. 40

Terminal Type [ANSI] ........................................................................................................... 41

Bits per second [115200] ..................................................................................................... 42

Data Bits [8] .......................................................................................................................... 42

Parity [None] ......................................................................................................................... 42

Stop Bits [1] .......................................................................................................................... 43

Hyper Threading Function [Enabled] ................................................................................. 44

Activ e Processor Cores [All] .............................................................................................. 44

Intel Intel

CPU C Sta te [Disabled] ........................................................................................................ 45

STAT Controller(s) [Enabled] .............................................................................................. 45

SATA Mode Selection [AHCI] .............................................................................................. 46

Hot Plug [Disabled] .............................................................................................................. 46

USB Devices ......................................................................................................................... 47

Legacy USB Support [Enabled] .......................................................................................... 47

Auto Recov ery Function [Disabled] ................................................................................... 48

VT-d [Disabled] ..................................................................................................................... 50

Virtualization Technology [Disabled] ...................................................................... 44

SpeedStep™ [Enabled] ............................................................................................. 44

Primary Display [Auto] ........................................................................................................ 50

Internal Gra phi cs [Enabled] ................................................................................................ 51

DVMT Pre-Allocated [256M] ................................................................................................ 51

DVMT Total Gfx Mem [MAX] ................................................................................................ 51

Page 86

INOX-F15C-ULT3 Stainless Panel PC

Page 74



Primary IGFX Boot Display [VBIOS Defaul t] ..................................................................... 52

Restore AC P ower Loss [Last State] ................................................................................. 54

PCIe Speed [Auto] ................................................................................................................ 54

Detec t No n-Compliance Device [Disabled] ....................................................................... 55

Administrator Password ..................................................................................................... 56

User Password ..................................................................................................................... 56

Bootup NumLock State [On] ............................................................................................... 56

Quiet Boot [Enabled] ........................................................................................................... 57

UEFI Boot [Disabled] ........................................................................................................... 57

Launch PXE OpROM [Disabled] ......................................................................................... 57

Option ROM Messa ges [Force BIOS] ................................................................................. 57

Boot Option Priority ............................................................................................................. 58

Save Changes and Reset .................................................................................................... 58

Discard Changes and Re set ............................................................................................... 59

Restore Defaults .................................................................................................................. 59

Save as User Defaults ......................................................................................................... 59

Restore User Defaults ......................................................................................................... 59

Page 87

INOX-F15C-ULT3 Stainless Panel PC

Page 75

Appendix

D Watchdog Timer

Page 88

INOX-F15C-ULT3 Stainless Panel PC

Page 76

NOTE:

The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating sy st ems.

The Watchdog Timer is a hardware-based timer that at tempts to restart the syst em when it stops working. The system may stop working because of external EMI or software bugs. The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.

A BIOS function call (INT 15H) is used to control the Watchdog Timer.

INT 15H:

AH – 6FH Sub-function:

AL – 2: Sets the Watchdog Timer’s period. BL: Time-out value (Its unit-second is dependent on the item “Watchdog

Timer unit select” in CMOS setup).

Table D-1: AH-6FH Sub-function

Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value is not zero, the Watchdog Timer starts counting down . When the timer val ue reaches zero, the system resets. To ensure that this reset condition does not occur, calling sub-function 2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled if the time-out value is set to zero.

A tolerance of at least 10% must be maintained to avoid unknown routines within the operating system (DOS), such as disk I/O that can be very time-consuming.

Page 89

INOX-F15C-ULT3 Stainless Panel PC

Page 77

The Watchdog Timer is activated through software. The software

NOTE:

application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has f i ni shed its countdown.

EXAMPLE PROGRAM:

; INITIAL TIMER PERIOD COUNTER

; W_LOOP: ;

MOV AX, 6F02H ;setting the time-out value MOV BL, 30 ;time-out value is 48 seconds INT 15H

; ; ADD THE APPLICATION PROG RAM HERE ;

CMP EXIT_AP, 1 ;is the application over? JNE W_LOOP ;No, restart the application

MOV AX, 6F02H ;disable Watchdog Timer MOV BL, 0 ; INT 15H

; ; EXIT ;

Page 90

INOX-F15C-ULT3 Stainless Panel PC

Page 78

Appendix

E Hazardous Materials

Disclosure

Page 91

INOX-F15C-ULT3 Stainless Panel PC

Page 79

The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain material s in the product, and is applicable t o China RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly Use Period” (EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.” This product may contain replaceable sub-assemblies/components which have a shorter EFUP such as batteries and lamps. These components will be separately marked.

Please refer to the following table.

Part Name Toxic or Hazardous Substances and Elements

Lead (Pb)

Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply Assemblies Battery O: This toxic or hazardous substance is contained in all of the homogeneous materia ls for the part is below the li m it

requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contain ed in at least one of the homogeneous ma terials for this part is above

O O O O O O O O O O O O O O O O O O

O O O O O O O O O O O O O O O O O O O O O O O O

O O O O O O

Mercury (Hg)

Cadmium (Cd)

Hexavalent Chromium (CR(VI))

Polybrominated Biphenyls (PBB)

Polybrominated Diphenyl Ethers (PBDE)

the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

Page 92

INOX-F15C-ULT3 Stainless Panel PC

Page 80

部件名称

有毒有害物质或元素

铅

汞

镉

六价铬

多溴联苯

多溴二苯

醚

壳体

显示

印刷电路板

金属螺帽

电缆组装

风扇组装

电力供应组装

电池

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

(Pb)

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代) 标准规定的限量要求以下。

O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O

(Hg)

(Cd)

(CR(VI))

(PBB)

(PBDE)

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代) 标准规定的限量要求。

IEI Technology INOX-F15C-ULT3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 Overview

1.2 Model Variations

1.3 Features

1.4 Front Panel

1.5 Rear Panel

1.6 System Specifications

1.7 Dimensions

2 Unpacking

2.1 Unpacking

2.2 Packing List

2.3 Optional Items

3 Installation

3.1 Anti-static Precautions

3.2 Installation Precautions

3.3 HDD Installation

3.4 External I/O Connectors

3.4.1 COM Port Connection

3.4.2 LAN Port Connection

3.4.3 USB Port Connection

3.4.3.1 Ferrite Core Installation

3.4.4 Power Input Connection

3.5 Mounting the System

3.6 Powering On the System

3.7 System Maintenance

3.8 Software Installation

3.9 Installing Windows 7 from USB 3.0 Drives

4 BIOS Setup

4.1 Introduction

4.1.1 Starting Setup

4.1.2 Using Setup

4.1.3 Getting Help

4.1.4 BIOS Menu Bar

4.2 Main

4.3 Advanced

4.3.1 ACPI Settings

4.3.2 F81866 Super IO Configuration

4.3.2.1 Serial Port n Configuration

4.3.2.1.1 Serial Port 1 Configuration

4.3.2.1.2 Serial Port 2 Configuration

4.3.3 F81866 H/W Monitor

4.3.4 RTC Wake Settings

4.3.5 Serial Port Console Redirection

4.3.5.1 Legacy Console Redirection Settings

4.3.5.2 Console Redirection Settings

4.3.6 CPU Configuration

4.3.7 SATA Configuration

4.3.8 USB Configuration

4.3.9 IEI Feature

4.4 Chipset

4.4.1 System Agent (SA) Configuration

4.4.1.1 Graphics Configuration

4.4.1.1.1 LCD Control

4.4.1.2 Memory Configuration

4.4.2 PCH-IO Configuration

4.4.2.1 PCI Express Configuration

4.5 Security

4.6 Boot

4.7 Exit

A Regulatory Compliance

B Safety Precautions

B.1 Safety Precautions

B.1.1 General Safety Precautions

B.1.2 Anti-static Precautions

B.1.3 Product Disposal

B.2 Maintenance and Cleaning Precautions

B.2.1 Maintenance and Cleaning

B.2.2 Cleaning Tools

C BIOS Menu Options

D Watchdog Timer