IEI Technology IMB-Q354 Quick Installation Manual

1

mircoATX Mother board Supports Intel® LGA-775 CPU with
a 800/1066/1333MHz FSB, Intel® Q35 & ICH9DO
Platform.

IMB-Q354

Quick Installation Guide

Version 1.11

June. 13, 2012

Package Contents

IMB-Q354 package includes the following items:

l 1 x IMB-Q354 single board computer
l 1 x Mini jumper pack
l 1 x Dual RS232 cable
l 1 x USB cable
l 6 x SATA cable
l 3 x SATA power cable
l 1 x I/O shielding
l 1 x Utility CD
l 1 x QIG (quick installation guide)

©2006 Copyright by IEI Technology corp.

All rights reserved.

2

Specifications

l CPU:LGA775 45nm Intel® Core™2 Quad(Yorkfield), Core™2

Duo(Wolfdale), Core2 Duo, Celeron® processor with a
800/1066/1333MHz FSB

l System Chipset: Intel® Q35 + ICH9-DO
l BIOS: AMI BIOS Label with 4MB SPI EEPROM
l System memory: Four 240pin 800/667MHz dual-channel DDR2

DIMM sockets (system max. 8GB)

l Ethernet: Dual GbE

LAN1: Intel® 82566DM (PHY) with Intel® AMT support

LAN2: Intel® 82573L (MAC + PHY)

l I/O Interface:

1 x FDD
1 x LPT
1 x PS/2 for KB/MS
4 x RS-232
6 x SATA 3Gb/s support RAID 0, 1, 10, 5
12 x USB 2.0(4 on the edge, 8 on board by pitch2.54mm

header)

l Digital I/O: 8-bit Digital I/O, 4-bit input / 4-bit output
l Infrared Interface: One Infrared Interface by pin header
l Display: VGA integrated in Intel® Q35
l Audio: Realtek ALC662
l TPM1.2: One 20-pin header on board for TPM
l Watchdog Timer: Software programmable supports 1~255 sec.

system reset

l Power Supply: ATX support
l Temperature: 0°C ~ 60°C(32°F ~ 140°F)

l Operating Humidity: 5% ~ 95%, non-condensing
l Dimensions: 244 (L) mm x 244 (W) mm
l Weight: GW 1.1Kg

3

Ordering Information

Standard:

IMBA-Q354-R11

microATX motherboard supports 45nm Intel® LGA775 Core™2 Duo
CPU with a 800/1066/1333MHz FSB, Intel® Q35 & ICH9DO platform, dual
Intel® PCIe GbE, six SATA 3Gb/s with RAID functions.

Optional:

CF-520-RS, CF-775A-RS, CF-775B-RS: CPU Cooler
TPM-IN01-R10: Infineon 20-pin Trusted Platform Module with S/W

Management Tool
TPM-SI01-R10: Sinosun 20-pin Trusted Platform Module with S/W
Management Tool
TPM-WI-1-R10: Winbond 20-pin Trusted Platform Module with S/W
Management Tool

Jumpers Setting

l

J_COM_F

2 ~

J_COM_F

4

:

Set the function of pin9 as

signal or voltage at COM2 ~ COM4

J_COM_F

2 ~

J_COM_F

4 1 - 2

Pin9 of COM1 and

COM2 as voltage

2 - 3 Pin9 of COM1 and COM2 as signal

“RING

”

l

J_COM_

V2 ~ J_COM_V4

:

Set the voltage level of pin9

at COM2 ~ COM4

J_COM_

V2 ~ J_COM_V4

1 - 2 +5V

2 - 3 +12V

l

J_CMO

S1:

Clear CMOS setup

JSPI_SEL1

DESCRIPTIO

N Short

1-2 Keep CMOS Setup(default)

Short

2-3 Clear CMOS Setup

4

Connection

l

KB_MS1A (Purple)

:

6-pin Mini-DIN Keyboard Connector

PIN NO.

DESCRIPTION

1 Keyboard Data

2 NC 3

GND

4

VCC

5

Keyboard Clock

6 NC

l

KB_MS1B (Green)

:

6-pin Mini-DIN Mouse Connector

PIN NO.

DESCRIPTION

1 Mouse Data

2 NC 3

GND

4

VCC

5

Mouse Cloc

k 6 NC

l

VGA:

15-pin Female Connector

PIN

DESCRIPTION

PIN

DESCRIPTION

35 RED 36

GREEN

37 BLUE 38

NC

39 GROUND 40

GROUND

41 GROUND 42

GROUND

43 VCC / NC 44

GROUND

45 NC 46

DDC DAT

47 HSYNC 48

VSYNC

49 DDCCLK

l

COM1:

D-SUB Serial Port Connector

PIN

DESCRIPTION

PIN

DESCRIPTION

26 (DCD)

31

(DSR)

27

(RXD)

32

(RTS)

28

(TXD)

33

(CTS)

29

(DTR)

34

(RI)

30 G

ROU

ND

5

l

LPT

:

Parallel Port Connector

PIN

DESCRIPTION PIN DESCRIPTION

1 STROBE# 2 DATA 0
3 DATA 1 4 DATA 2
5 DATA 3 6 DATA 4
7 DATA 5 8 DATA 6
9 DATA 7 10 ACKNOWLEDGE

11 BUSY 12 PAPER EMPTY

13 PRINTER SELECT

14

AUTO FORM FEED #

15

ERROR#

16

INITIALIZE

17

PRINTER SELECT

IN# 18 GROUND

19

GROUND

20

GROUND

21

GROUND

22

GROUND

23

GROUND

24

GROUND

25

GROUND

l LAN1_USB01、LAN2_USB23: RJ45 LAN and USB Connector

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 MDIA3- 5 MDIA1+
2 MDIA3+ 6 MDIA2+-

3. MDIA2- 7 MDIA0-

4. MDIA1- 8 MDIA0+

USB

PIN NO.

DESCRIPTION

1 VCC
2 DATA­3 DATA+
4 GROUND

l

AUDIO_CV1:

Audio Input and Output Connector

AUDIO_CV1

PIN NO.

DESCRIPTION

Line-in CD/DVD or other audio

source input port

Line-out Connect this port to

headphone or speaker

Microphone

Connect this port to

microphone

6

l

SATA1~SATA6:

Serial ATA Connector

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1

GND

5 RX-

2 TX+ 6 RX+
3 TX- 7 GND
4 GND 8 N/C

l USB45、USB67、USB89、USB1011:Internal USB Connector

USB45, USB67, USB89, USB1011

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 VCC 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA­7 GND 8 VCC

l

FDD1

:

FDD Connector

PIN

NO.

DESCRIPTION

PIN

NO.

DESCRIPTION

1 GND

2

REDUCE WRITE

3 GND 4

N/C

5

N/C

6

N/C

7

GND

8

INDEX#

9

GND

10

MOTOR ENABLE A

# 11 GND

12

DRIVE SELECT B#

13

GND

14

DRIVE SELECT A#

15

GND

16

MOTOR ENABLE B#

17

GND

18

DIRECTION#

19

GND

20

STEP#

21

GND

22

WRITE DATA#

23

GND

24

WRITE GATE#

25

GND

26

TRACK 0#

27

GND

28

WRITE PROTECT#

29

GND

30

READ DATA#

31

GND

32

SIDE 1 SE

LECT#

33

GND

34

DISK CHANGE#

l

SYS_FAN1:

System Fan

Connector

PIN NO.

DESCRIPTION

1 Ground

2 +12V

3

Rotation S

ignal

l

CPU_FAN1:

CPU Fan

Connector

PIN NO.

DESCRIPTION

1 Ground

2 +12V

3

Rotation Signal

4

Control

7

l

DIO1:

Digital Input / Output Connector

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 Ground 2 VCC
3 Output 3 4 Output 2
5 Output 1 6 Output 0
7 Input 3 8 Input 2
9 Input 1 10 Input 0

l

F_PANEL1

:

External Switches and Indicators Panel

PIN

DESCRIPTION

PIN

DESC

RIPTION

Power LED

1

+5V

2

+5V

Speaker

3

N/C

4

N/C

5 GROU

ND 6 N/C

PWRBTN

7

PWRBTN+

8

Speaker

9

PWRBTN

- 10 N/C

RESET

HDDLED

11

+5V

12

Reset

- 13 HDLED

- 14 GND

l

PCIE_12V1

:

PCI-E Power

Connector

PIN NO.

DESCRIPTION

1 VCC12V

2

GND

3

GND

4

VCC5V

l

IR1

:

Infrared Connector

PIN NO.

DESCRIPTION

1 VCC

2 NC 3 IR-RX 4 GND 5 IR-TX

l

FRONT

-

PANEL

1

: Front Audio Connector

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1

MIC_L

2 GND

3 MIC_R 4 Audio Detect

5. LINE2-R 6 GND
7 Jack Detection 8 N/C

9 LINE2-L 10 GND

l

SPDIF1

: Internal SPDIF Connector

PIN

DESCRIPTION

1

5V

2

N/C

3

SPDIFOUT

4

GND

5

SPDIFIN

l

CD_IN1

: Internal CD

In Connector

PIN

DESCRIPTION

1

CD-L

2

CD-GND

3

CD-GND

4

CD-R

8

l

COM2 ~ COM4

:

Internal Serial Port Connector

PIN NO.

DESCRIPTION

1 DATA CARRIER DETECT (DCD

1) 2

RECEIVE DATA (RXD

1) 3

TRANSMIT DATA (TXD

1) 4

DATA TERMINAL READY (DTR

1) 5

GND

(GND1)

6 DATA SET READY (DSR

1) 7

REQUEST TO SEND (RTS

1) 8

CLEAR TO SEND (CTS

1) 9

RING INDICATOR (RI

1) 10

N/C

l

TPM1

:

Trusted Platform Module Connector

DVI Connector

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 FWHPCLK

2

GND

3

LFRAME#

4

KEY

5

PCIRST#

6

VCC

7

LAD3

8

LAD2

9

VCC3

10

LAD1

11

LAD0

12

GND

13

SMBCLK

14

SMBDATA

15

3VDUAL

16

SERIRQ

17

GND

18

CLKRUN#

19

LPCPD#

20

LDRQ#

l

J

SPI1

: SPI Flash Connector

PIN

DESCRIPTION

PIN

DESCRIPTION

1

VCC 2

GND

3 CS# 4

CLOCK

5

SO 6

SI

7

NC 8

NC

l CPU12V1

:

CPU Power Connector

ATX

-

12V1 (CPU)

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1 GND

2

GND

3

+12V

4

+12V

9

Board Layout: Jumper and Connector Locations