Page 1
IMB-C2060 microATX Motherboard
MODEL:
IMB-C2060
microATX LGA1155 Motherboard for Intel® Xeon™ E3 and
Intel® Core™ i3 CPU, Intel® C206, DDR3, VGA/DVI/HDMI
Dual Intel PCIe GbE, Two USB 3.0 ports, Ten COM ports
Two SATA 6Gb/s ports, Audio and RoHS
User Manual
Rev. 2.01 –October 2, 2014
Page i
Page 2
IMB-C2060 microATX Motherboard
Revision
Date Version Changes
October 3, 2014 2.01 Updated Chapter 5 BIOS.
December 9, 2013 2.00 Updated for R20 version.
November, 12 2012 1.04 Modified Appendix E: Intel® Matrix Storage Manager
July 6, 2012 1.03 Modified Table 3-16: RS-422/485 Connector Pinouts
August 16, 2011 1.02 Modified Section 4.3.1: AT/ATX Power Mode Jumper
Added Section 4.6 Intel® AMT Setup Procedure
Added Chapter 6: Software Drivers
June 30, 2011 1.01 Modified Section 4.2.2 Socket LGA1155 Cooling Kit
Installation warning and procedure
April 25, 2011 1.00 Initial release
Page ii
Page 3
IMB-C2060 microATX Motherboard
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
Page 4
IMB-C2060 microATX Motherboard
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 BENEFITS ................................................................................................................... 2
1.3 FEATURES................................................................................................................... 3
1.4 CONNECTORS ............................................................................................................. 4
1.5 DIMENSIONS............................................................................................................... 5
1.6 DATA FLOW................................................................................................................ 6
1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7
2 PACKING LIST............................................................................................................. 9
2.1 ANTI-STATIC PRECAUTIONS...................................................................................... 10
2.2 UNPACKING PRECAUTIONS....................................................................................... 10
2.3 PACKING LIST............................................................................................................11
2.4 OPTIONAL ITEMS...................................................................................................... 12
3 CONNECTORS ........................................................................................................... 13
3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 14
3.1.1 IMB-C2060 Layout .......................................................................................... 14
3.1.2 Peripheral Interface Connectors ..................................................................... 15
3.1.3 External Interface Panel Connectors............................................................... 16
INTERNAL PERIPHERAL CONNECTORS ...................................................................... 16
3.2
3.2.1 ATX Power Connector ..................................................................................... 16
3.2.2 Battery Connector............................................................................................ 18
3.2.3 CPU Fan Connector........................................................................................ 19
3.2.4 CPU Power Connector.................................................................................... 20
3.2.5 Digital I/O Connector...................................................................................... 20
3.2.6 Front Panel Audio Connector.......................................................................... 22
3.2.7 Front Panel Connector.................................................................................... 22
3.2.8 FW Programming............................................................................................. 23
3.2.9 Infrared Interface Connector........................................................................... 24
3.2.10 Memory Card Slot.......................................................................................... 25
Page iv
Page 5
IMB-C2060 microATX Motherboard
3.2.11 PCH Fan Connector....................................................................................... 26
3.2.12 PCI Express Power........................................................................................ 27
3.2.13 SATA 3Gb/s Drive Connectors....................................................................... 28
3.2.14 SATA 6Gb/s Drive Connectors....................................................................... 29
3.2.15 Serial Port Connector, RS-422/485................................................................ 30
3.2.16 Serial Port Connectors, RS-232..................................................................... 31
3.2.17 SMBus Connector .......................................................................................... 34
3.2.18 SPDIF Connector........................................................................................... 35
3.2.19 SPI Connector................................................................................................ 35
3.2.20 System Fan Connectors.................................................................................. 36
3.2.21 TPM Connector.............................................................................................. 37
3.2.22 USB Connectors............................................................................................. 38
3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 40
3.3.1 Audio Connector .............................................................................................. 40
3.3.2 Keyboard/Mouse Connector............................................................................ 41
3.3.3 Ethernet and USB Connector........................................................................... 42
3.3.4 HDMI Port Connector..................................................................................... 43
3.3.5 Serial Port Connectors (COM1)...................................................................... 43
3.3.6 VGA and DVI Connector................................................................................. 44
4 INSTALLATION ......................................................................................................... 46
4.1 ANTI-STATIC PRECAUTIONS...................................................................................... 47
4.2 INSTALLATION CONSIDERATIONS.............................................................................. 47
4.2.1 Socket LGA1155 CPU Installation .................................................................. 49
4.2.2 Socket LGA1155 Cooling Kit Installation........................................................ 52
4.2.3 DIMM Installation........................................................................................... 54
JUMPER SETTINGS .................................................................................................... 55
4.3
4.3.1 AT/ATX Power Mode Jumper .......................................................................... 55
4.3.2 Clear CMOS Jumper........................................................................................ 56
4.3.3 ME Debug Jumper........................................................................................... 57
4.3.4 USB Power Select Jumper............................................................................... 58
4.3.5 Wake-on LAN Jumper ...................................................................................... 59
4.4 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 60
4.4.1 SATA Drive Connection ................................................................................... 60
4.5 EXTERNAL PERIPHERAL INTERFACE CONNECTION................................................... 61
Page v
Page 6
IMB-C2060 microATX Motherboard
4.5.1 Audio Connector .............................................................................................. 61
4.5.2 LAN Connection............................................................................................... 62
4.5.3 Parallel Device Connection............................................................................. 63
4.5.4 PS/2 Keyboard and Mouse Connection........................................................... 64
4.5.5 Serial Device Connection ................................................................................ 65
4.5.6 USB Connection (Dual Connector)................................................................. 66
4.5.7 VGA Monitor Connection ................................................................................ 67
INTEL® AMT SETUP PROCEDURE............................................................................. 68
4.6
5 BIOS.............................................................................................................................. 70
5.1 INTRODUCTION......................................................................................................... 71
5.1.1 Starting Setup................................................................................................... 71
5.1.2 Using Setup...................................................................................................... 71
5.1.3 Getting Help..................................................................................................... 72
5.1.4 Unable to Reboot after Configuration Changes
.............................................. 72
5.1.5 BIOS Menu Bar................................................................................................ 72
5.2 MAIN........................................................................................................................ 73
5.3 ADVANCED............................................................................................................... 74
5.3.1 T rusted Computing........................................................................................... 75
5.3.2 CPU Configuration.......................................................................................... 76
5.3.2.1 CPU Information....................................................................................... 77
5.3.3 SATA Configuration ......................................................................................... 78
5.3.4 Intel TXT(LT) Configuration............................................................................ 79
5.3.5 AMT Configuration.......................................................................................... 80
5.3.6 USB Configuration........................................................................................... 81
5.3.7 F81216 Second Super IO Configuration ......................................................... 82
5.3.7.1 Serial Port 7 Configuration....................................................................... 82
5.3.7.2 Serial Port 8 Configuration....................................................................... 83
5.3.7.3 Serial Port 9 Configuration....................................................................... 84
5.3.7.4 Serial Port 10 Configuration..................................................................... 85
5.3.8 F81866 Super IO Configuration
...................................................................... 86
5.3.8.1 Serial Port n Configuration....................................................................... 86
5.3.9 F81866 H/W Monitor....................................................................................... 91
5.3.9.1 Smart Fan Mode Configuration................................................................ 92
5.3.10 Serial Port Console Redirection.................................................................... 93
Page vi
Page 7
IMB-C2060 microATX Motherboard
5.3.11 IEI Feature..................................................................................................... 97
CHIPSET ................................................................................................................... 98
5.4
5.4.1 PCH-IO Configuration .................................................................................... 99
5.4.2 System Agent (SA) Configuration .................................................................. 100
5.4.2.1 Graphics Configuration........................................................................... 101
5.5 BOOT...................................................................................................................... 102
5.6 SECURITY............................................................................................................... 104
5.7 EXIT....................................................................................................................... 105
6 SOFTWARE DRIVERS............................................................................................ 107
6.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 108
6.2
SOFTWARE INSTALLATION ...................................................................................... 108
6.3 CHIPSET DRIVER INSTALLATION..............................................................................110
6.4 GRAPHICS DRIVER INSTALLATION...........................................................................114
6.5 LAN DRIVER INSTALLATION...................................................................................116
6.6 AUDIO DRIVER INSTALLATION ............................................................................... 120
6.7 USB 3.0 DRIVER INSTALLATION ............................................................................ 122
6.8 INTEL® AMT DRIVER AND APPLICATION............................................................... 125
6.8.1 Intel® Management Engine Components Installation................................... 125
6.8.2 Intel® IT Director Application Installation................................................... 129
A BIOS OPTIONS ........................................................................................................ 136
B TERMINOLOGY...................................................................................................... 139
C DIGITAL I/O INTERFACE..................................................................................... 143
INTRODUCTION...................................................................................................... 144
C.1
C.2 DIO CONNECTOR PINOUTS.................................................................................... 144
C.3 ASSEMBLY LANGUAGE SAMPLE 1.......................................................................... 145
C.4 ASSEMBLY LANGUAGE SAMPLE 2.......................................................................... 145
D WATCHDOG TIMER.............................................................................................. 146
E INTEL® MATRIX STORAGE MANAGER ......................................................... 149
E.1 INTRODUCTION ...................................................................................................... 150
E.1.1 Precautions.................................................................................................... 150
E.2 FEA TURES AND BENEFITS....................................................................................... 151
E.3 ACCESSING THE INTEL® MATRIX STORAGE MANAGER......................................... 151
Page vii
Page 8
INST ALLING THE OPERATING SYSTEM TO THE RAID ARRAY ................................. 152
E.4
IMB-C2060 microATX Motherboard
F COMPATIBILITY.....................................................................................................153
F.1 COMPATIBLE OPERATING SYSTEMS ........................................................................ 154
F.2 COMPATIBLE PROCESSORS...................................................................................... 154
G HAZARDOUS MATERIALS DISCLOSURE....................................................... 155
G.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 156
Page viii
Page 9
IMB-C2060 microATX Motherboard
List of Figures
Figure 1-1: IMB-C2060....................................................................................................................2
Figure 1-2: Connectors ..................................................................................................................4
Figure 1-3: IMB-C2060 Dimensions (mm) ....................................................................................5
Figure 1-4: Data Flow Diagram......................................................................................................6
Figure 3-1: Connectors and Jumpers.........................................................................................14
Figure 3-2: ATX Power Connector Location..............................................................................17
Figure 3-3: Battery Connector Location.....................................................................................18
Figure 3-4: CPU Fan Connector Location..................................................................................19
Figure 3-5: CPU Power Connector Location..............................................................................20
Figure 3-6: Digital I/O Connector Location ................................................................................21
Figure 3-7: Front Panel Audio Connector Location..................................................................22
Figure 3-8: Front Panel Connector Location .............................................................................23
Figure 3-9: FW Programming Connector Location...................................................................24
Figure 3-10: Infrared Connector Location..................................................................................25
Figure 3-11: Memory Card Slot Location ...................................................................................26
Figure 3-12: PCH Fan Connector Location................................................................................27
Figure 3-13: PCIe Power Location ..............................................................................................28
Figure 3-14: SATA 3Gb/s Drive Connector Locations..............................................................29
Figure 3-15: SATA 6Gb/s Drive Connector Locations..............................................................30
Figure 3-16: RS-422/485 Connector Location............................................................................31
Figure 3-17: Serial Port Connector Locations...........................................................................32
Figure 3-18: SMBus Connector Location...................................................................................34
Figure 3-19: SPDIF Connector Location ....................................................................................35
Figure 3-20: SPI Connector Location .........................................................................................36
Figure 3-21: System Fan Connector Locations.........................................................................37
Figure 3-22: TPM Connector Location........................................................................................38
Figure 3-23: USB Connector Locations......................................................................................39
Figure 3-24: External Peripheral Interface Connector..............................................................40
Figure 3-25: Audio Connector.....................................................................................................41
Figure 3-26: Serial Port Connector Pinouts...............................................................................44
Page ix
Page 10
Figure 3-27: VGA Connector .......................................................................................................45
Figure 4-1: Intel LGA1155 Socket ...............................................................................................49
Figure 4-2: Remove Protective Cover.........................................................................................50
Figure 4-3: CPU Socket Load Plate.............................................................................................50
Figure 4-4: Insert the Socket LGA1155 CPU..............................................................................51
Figure 4-5: Cooling Kits (CF-1156A-RS and CF-1156E-RS) .....................................................52
Figure 4-6: Cooling Kit Support Bracket....................................................................................53
Figure 4-7: DIMM Installation.......................................................................................................54
Figure 4-8: AT/ATX Power Mode Jumper Location...................................................................56
Figure 4-9: Clear BIOS Jumper Location ...................................................................................57
Figure 4-10: ME Debug Jumper Location ..................................................................................57
Figure 4-11: USB Power Select Jumper Location.....................................................................58
Figure 4-12: Wake-on LAN Jumper Location.............................................................................59
Figure 4-13: SATA Drive Cable Connection...............................................................................60
IMB-C2060 microATX Motherboard
Figure 4-14: SATA Power Drive Connection..............................................................................61
Figure 4-15: Audio Connector.....................................................................................................62
Figure 4-16: LAN Connection......................................................................................................63
Figure 4-17: Parallel Device Connector......................................................................................64
Figure 4-18: PS/2 Keyboard/Mouse Connector.........................................................................65
Figure 4-19: Serial Device Connector.........................................................................................66
Figure 4-20: USB Connector........................................................................................................67
Figure 4-21: VGA Connector .......................................................................................................68
Figure 6-1: Introduction Screen............................................................................................... 109
Figure 6-2: Available Drivers.................................................................................................... 109
Figure 6-3: Chipset Driver Screen............................................................................................ 110
Figure 6-4: Chipset Driver Welcome Screen........................................................................... 111
Figure 6-5: Chipset Driver License Agreement...................................................................... 111
Figure 6-6: Chipset Driver Read Me File ................................................................................. 112
Figure 6-7: Chipset Driver Setup Operations ......................................................................... 113
Figure 6-8: Chipset Driver Installation Finish Screen............................................................ 113
Figure 6-9: Graphics Driver Welcome Screen........................................................................ 114
Figure 6-10: Graphics Driver License Agreement.................................................................. 115
Figure 6-11: Graphics Driver Setup Operations..................................................................... 115
Figure 6-12: Graphics Driver Installation Finish Screen ....................................................... 116
Figure 6-13: Intel® Network Connection Menu....................................................................... 117
Page x
Page 11
IMB-C2060 microATX Motherboard
Figure 6-14: LAN Driver Welcome Screen .............................................................................. 117
Figure 6-15: LAN Driver License Agreement.......................................................................... 118
Figure 6-16: LAN Driver Setup Options................................................................................... 119
Figure 6-17: LAN Driver Installation ........................................................................................ 119
Figure 6-18: LAN Driver Installation Complete....................................................................... 120
Figure 6-19: Audio Driver – Extracting Files........................................................................... 121
Figure 6-20: Audio Driver Welcome Screen............................................................................ 121
Figure 6-21: Audio Driver Installation...................................................................................... 121
Figure 6-22: Audio Driver Installation Complete.................................................................... 122
Figure 6-23: USB 3.0 Driver Welcome Screen........................................................................ 123
Figure 6-24: USB 3.0 Driver License Agreement.................................................................... 123
Figure 6-25: USB 3.0 Driver Installation Screen..................................................................... 124
Figure 6-26: USB 3.0 Driver Update Complete ....................................................................... 124
Figure 6-27: Intel® ME Driver Welcome Screen ..................................................................... 126
Figure 6-28: Intel® ME Driver License Agreement................................................................. 127
Figure 6-29: Intel® ME Driver Read Me File............................................................................ 127
Figure 6-30: Intel® ME Driver Setup Operations.................................................................... 128
Figure 6-31: Intel® ME Driver Installation Finish Screen ...................................................... 129
Figure 6-32: IT Director Welcome Screen ............................................................................... 130
Figure 6-33: IT Director License Agreement........................................................................... 131
Figure 6-34: IT Director Installation......................................................................................... 131
Figure 6-35: IT Director Installation Complete........................................................................ 132
Figure 6-36: IT Director Configuration Tool Welcome Screen.............................................. 133
Figure 6-37: IT Director – Creating Password ........................................................................ 134
Figure 6-38: IT Director Configuration Complete................................................................... 135
Page xi
Page 12
IMB-C2060 microATX Motherboard
List of Tables
Table 1-1: IMB-C2060 Specifications............................................................................................8
Table 2-1: Packing List.................................................................................................................12
Table 2-2: Optional Items.............................................................................................................12
Table 3-1: Peripheral Interface Connectors...............................................................................16
Table 3-2: Rear Panel Connectors..............................................................................................16
Table 3-3: ATX Power Connector Pinouts .................................................................................17
Table 3-4: Battery Connector Pinouts........................................................................................19
Table 3-5: CPU Fan Connector Pinouts......................................................................................19
Table 3-6: CPU Power Connector Pinouts.................................................................................20
Table 3-7: Digital I/O Connector Pinouts....................................................................................21
Table 3-8: Front Panel Audio Connector Pinouts .....................................................................22
Table 3-9: Front Panel Connector Pinouts.................................................................................23
Table 3-10: FW Programming Connector Pinouts ....................................................................24
Table 3-11: Infrared Connector Pinouts.....................................................................................25
Table 3-12: PCH Fan Connector Pinouts ...................................................................................27
Table 3-13: PCIe Power Pinouts..................................................................................................28
Table 3-14: SATA 3Gb/s Drive Connector Pinouts....................................................................29
Table 3-15: SATA 6Gb/s Drive Connector Pinouts....................................................................30
Table 3-16: RS-422/485 Connector Pinouts...............................................................................31
Table 3-17: DB-9 RS-422/485 Pinouts.........................................................................................31
Table 3-18: COM3~6 Serial Port Connector Pinouts.................................................................33
Table 3-19: COM7~10 Serial Port Connector Pinouts...............................................................33
Table 3-20: SMBus Connector Pinouts ......................................................................................34
Table 3-21: SPDIF Connector Pinouts........................................................................................35
Table 3-22: SPI Connector Pinouts.............................................................................................36
Table 3-23: System Fan Connector Pinouts..............................................................................37
Table 3-24: TPM Connector Pinouts...........................................................................................38
Table 3-25: USB1 Connector Pinouts.........................................................................................39
Table 3-26: USB2 Connector Pinouts.........................................................................................39
Table 3-27: USB3 Connector Pinouts.........................................................................................40
Page xii
Page 13
IMB-C2060 microATX Motherboard
Table 3-28: USB4 Connector Pinouts.........................................................................................40
Table 3-29: PS/2 Connector Pinouts...........................................................................................42
Table 3-30: LAN Pinouts ..............................................................................................................42
Table 3-31: USB Port Pinouts......................................................................................................42
Table 3-32: HDMI Connector Pinouts .........................................................................................43
Table 3-33: Serial Port Connector Pinouts ................................................................................44
Table 3-34: VGA Connector Pinouts...........................................................................................45
Table 3-35: DVI Connector Pinouts.............................................................................................45
Table 4-1: Jumpers.......................................................................................................................55
Table 4-2: AT/ATX Power Mode Jumper Settings.....................................................................56
Table 4-3: Clear BIOS Jumper Settings......................................................................................56
Table 4-4: ME Debug Jumper Settings.......................................................................................58
Table 4-5: USB Power Select Jumper Settings .........................................................................58
Table 4-6: Wake-on LAN Jumper Settings.................................................................................59
Table 5-1: BIOS Navigation Keys................................................................................................72
Table 6-1: Digital I/O Connector Pinouts................................................................................. 144
Page xiii
Page 14
IMB-C2060 microATX Motherboard
BIOS Menus
BIOS Menu 1: Main.......................................................................................................................73
BIOS Menu 2: Advanced..............................................................................................................75
BIOS Menu 3: Trusted Computing..............................................................................................75
BIOS Menu 4: CPU Configuration...............................................................................................76
BIOS Menu 5: CPU Information...................................................................................................77
BIOS Menu 6: SATA Configuration.............................................................................................78
BIOS Menu 7: Intel TXT(LT) Configuration ................................................................................79
BIOS Menu 8: AMT Configuration...............................................................................................80
BIOS Menu 9: USB Configuration...............................................................................................81
BIOS Menu 10: F81216 Second Super IO Configuration..........................................................82
BIOS Menu 11: F81866 Super IO Configuration........................................................................86
BIOS Menu 12: Serial Port n Configuration Menu.....................................................................86
BIOS Menu 13: F81866 H/W Monitor...........................................................................................91
BIOS Menu 14: Smart Fane Mode Configuration ......................................................................92
BIOS Menu 15: Serial Port Console Redirection.......................................................................94
BIOS Menu 16: IEI Feature...........................................................................................................97
BIOS Menu 17: Chipset................................................................................................................98
BIOS Menu 18: PCH-IO Configuration........................................................................................99
BIOS Menu 19: System Agent (SA) Configuration................................................................. 100
BIOS Menu 20: Graphics Configuration.................................................................................. 101
BIOS Menu 21: Boot.................................................................................................................. 102
BIOS Menu 22: Security............................................................................................................ 104
BIOS Menu 23: Exit.................................................................................................................... 105
Page xiv
Page 15
IMB-C2060 microATX Motherboard
Chapter
1
1 Introduction
Page 1
Page 16
1.1 Introduction
IMB-C2060 microATX Motherboard
Figure 1-1: IMB-C2060
The IMB-C2060 is a microATX motherboard. It accepts a Socket LGA1155 Intel® Xeon™
E3 or Intel® Core™ i3 processor and supports four 240-pin 1333/1066 MHz dual-channel
DDR3 DIMM modules up to 32.0 GB maximum. The IMB-C2060 includes a VGA, HDMI,
and DVI-D port. Expansion and I/O include one PCI slot, one PCIe x16 slot, one PCIe x4
slot, one PCIe x16 slot with x8 signal, two USB 3.0 ports on the rear panel by ASMedia
ASM1042, two USB 2.0 on the rear panel, eight USB 2.0 by pin header, four SATA 3Gb/s
connectors, two SATA 6Gb/s connectors, ten COM ports, and a keyboard/mouse
connector.
1.2 Benefits
Some of the IMB-C2060 motherboard benefits include:
Powerful graphics with multiple monitors
Staying connected with both wired LAN connections
Speedy running of multiple programs and applications
Page 2
Page 17
IMB-C2060 microATX Motherboard
1.3 Features
Some of the IMB-C2060 motherboard features are listed below:
microATX
RoHS compliant
LGA1155 CPU socket
One PCI card expansion slot
One PCIe x16 card expansion slot
One PCIe x16 card expansion slot with x8 signal
One PCIe x4 card expansion slot
Multiple PCIe expansion card configurations:
Slot PCIe x16 PCIe x8 PCIe x4 PCI
Configuration 1 1 N/A 1 1
Configuration 2 N/A 2 1 1
Configuration 3 N/A 1 1 1
Supports two dual-channel DDR3 DIMMs
One external RS-232 serial port
Eight internal RS-232 serial ports connectors
One internal RS-422/485 serial port connector
Two Intel® PCIe Gigabit Ethernet connectors
Four SATA 3Gb/s connectors
Two SATA 6Gb/s connectors
High Definition Audio
Intel® C206 Chipset
Page 3
Page 18
1.4 Connectors
The connectors on the IMB-C2060 are shown in the figure below.
IMB-C2060 microATX Motherboard
Figure 1-2: Connectors
Page 4
Page 19
IMB-C2060 microATX Motherboard
1.5 Dimensions
The main dimensions of the IMB-C2060 are shown in the diagram below.
Figure 1-3: IMB-C2060 Dimensions (mm)
Page 5
Page 20
1.6 Data Flow
6Figure 1-4 shows the data flow between the system chipset, the CPU and other
components installed on the motherboard.
IMB-C2060 microATX Motherboard
Figure 1-4: Data Flow Diagram
Page 6
Page 21
IMB-C2060 microATX Motherboard
1.7 Technical Specifications
IMB-C2060 technical specifications are listed below.
Specification/Model IMB-C2060
Form Factor
CPU Supported
Northbridge Chipset
Integrated Graphics
Memory
Southbridge Chipset
Audio
BIOS
Digital I/O
Ethernet Controllers
Super I/O Controller
microATX
LGA1155 Socket Intel® Xeon™ E3 and Intel® Core™ i3
Intel® C206
Supports DirectX 10.1/OpenGL 3.0
Full MPEG2, VC1, AVC Decode
Four 240-pin 1333/1066 MHz Dual-Channel DDR3 SDRAM DIMMs
support up to 32.0 GB maximum
Intel® C206
Realtek ALC892 HD Audio codec (line-in, line-out, mic-in)
UEFI BIOS
24-bit, 12-bit input/12-bit output
LAN1: Intel® 82574L PCIe Ethernet controller
LAN2: Intel® 82579 PHY with Intel® AMT 7.0 supported
Fintek F81866
Watchdog Timer
Expansion
PCI
PCIe
I/O Interface Connectors
Audio Connectors
Software programmable supports 1~2 55 sec. system reset
One PCI slot
One PCIe x4 slot
One PCIe x16 slot
One PCIe x16 slot (with x8 signal)
One external audio jack (line-in, line-out, mic-in)
One internal front panel audio connector (2x5 pin header)
Page 7
Page 22
Specification/Model IMB-C2060
IMB-C2060 microATX Motherboard
Display port
Ethernet
Keyboard/Mouse
TPM
Serial Ports
USB ports
Serial ATA
One VGA Integrated in the Intel® C206
One HDMI Integrated in the Intel® C206
One DVI-D Integrated in the Intel® C206
Two RJ-45 ports
Dual PS/2 port
2 x 10-pin header
One external RS-232 serial port
One RS-422/485 via internal wafer connector
Eight RS-232 via internal box headers
Two external USB 2.0 ports on rear IO
Two external USB 3.0 ports on rear IO by ASMedia ASM1042
Eight internal USB 2.0 ports by pin header
Four SATA 3Gb/s channels with 3.0 Gb/s data transfer rates
Two SATA 6Gb/s channels with 6.0 Gb/s data transfer rates
Environmental and Power Specifications
Power Supply
Power Consumption
Operating
Temperature
Humidity
Physical Specifications
Dimensions
Weight GW/NW
Table 1-1: IMB-C2060 Specifications
ATX supported
3.3V@1.75A, 5V@6.61A , 12V@3.68A, 12V@0.09A, 5VSb@0.12
(2.60GHz Intel® CPU with four 4GB 1333MHz DDR3 DIMMs)
-20ºC ~ 60ºC/-4°F ~ 140°F
5% ~ 95% (non-condensing)
244 mm x 244 mm
1200 g / 680 g
Page 8
Page 23
IMB-C2060 microATX Motherboard
Chapter
2
2 Packing List
Page 9
Page 24
2.1 Anti-static Precautions
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:
Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.
Self-grounding: Touch a grounded conductor every few minutes to discharge
any excess static buildup.
IMB-C2060 microATX Motherboard
Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.
Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Unpacking Precautions
When the IMB-C2060 is unpacked, please do the following:
Follow the antistatic guidelines above.
Make sure the packing box is facing upwards whe n opening.
Make sure all the packing list items are present.
Page 10
Page 25
IMB-C2060 microATX Motherboard
2.3 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
IMB-C2060 was purchased from or contact an IEI sales representative
directly by sending an email to 32sales@iei.com.tw.
The IMB-C2060 is shipped with the following components:
Quantity Item and Part Number Image
1 IMB-C2060
4 SATA cable
(P/N: 32801-000703-200-RS)
1 Quad port RS-232 cabl e
(400/400/400/400mm)
(P/N: 32205-001203-100-RS)
1 I/O shielding
(P/N: 45014-0028C0-01-RS)
1 Mini jumper pack (2.54mm)
(P/N:33100-000079-RS)
1 Utility CD
Page 11
Page 26
Quantity Item and Part Number Image
1 Quick Installation Guide
Table 2-1: Packing List
2.4 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number Image
Dual-port USB cable with bracket
(P/N: 19800-003100-300-RS)
IMB-C2060 microATX Motherboard
SATA Power Cable
(P/N: 32102-000100-200-RS)
LGA1155/LGA1 156 Cooler kit (1U Chassis com p atibl e, 73W)
(P/N: CF-1 156A-RS-R11)
LGA1155/LGA1156 Cooler kit (95W)
(P/N: CF-1156E-R11)
RS-422/485 cable, 200mm
(P/N: 32205-003800-100-RS)
20-Pin Infineon TPM Module, S/W management tool, firmware
V3.17
Page 12
(P/N: TPM-IN01-R1 1)
Table 2-2: Optional Items
Page 27
IMB-C2060 microATX Motherboard
Chapter
3
3 Connectors
Page 13
Page 28
3.1 Peripheral Interface Connectors
This chapter details all the jumpers and connectors.
3.1.1 IMB-C2060 Layout
The figures below show all the connectors and jumpers.
IMB-C2060 microATX Motherboard
Figure 3-1: Connectors and Jumpers
Page 14
Page 29
IMB-C2060 microATX Motherboard
3.1.2 Peripheral Interface Connectors
The table below lists all the connectors on the board.
Connector Type Label
ATX Power connector 24-pin A TX ATX
Battery connector Battery holder BAT1
CPU fan 4-pin wafer CPU_FAN
CPU power 4-pin connector CPU12V1
Digital I/O 26-pin header DIO1
Front panel audio 10-pin header FP_AUDIO
Front panel 14-pin hea der F_PANEL1
FW programming 8-pin header CN1
Infrared interface 5-pin header IR1
Memory card DIMM slot DIMM1, DIMM2
PCH fan connector 3-pin wafer PCH_FAN1
PCIe power 4-pin connector PCIE_12V1
SATA 3Gb/s drive connector 16-pin SATA
connector
SATA 6Gb/s drive connector 7-pin SATA connector SATA1, SATA2
Serial port, RS-422/485 4-pin wafer COM2
Serial port, RS-232 40-pin box headers COM3-6, COM7-10
SMBus connector 4-pin wafer SMBUS_1
SPDIF 5-pin header SPDIF1
SPI connector 8-pin header SPI
System fan connectors 3-pin wafer SYS_FAN1,
SATA3, SATA 4,
SATA5, SATA 6
SYS_FAN2
TPM connector 20-pin header TPM
Page 15
Page 30
Connector Type Label
USB connectors 8-pin headers USB1, USB2, USB3,
Table 3-1: Peripheral Interface Connectors
3.1.3 External Interface Panel Connectors
The table below lists the connectors on the external I/O panel.
Connector Type Label
Audio connector Audio jack AUDIO_JACK
Keyboard/Mouse Dual PS/2 KBMS
Ethernet and USB ports RJ-45, USB LAN1_USB
IMB-C2060 microATX Motherboard
USB4
HDMI connector HDMI port HDMI
Serial Port connector (COM1) 9-pin male DB-9 COM1
VGA and DVI connector 15-pin female,
Table 3-2: Rear Panel Connectors
3.2 Internal Peripheral Connectors
The section describes all of the connectors on the IMB-C2060.
3.2.1 ATX Power Connector
CN Label: ATX
CN Type:
CN Location:
24-pin A TX
See Figure 3-2
LAN2_USB
DVI+CRT
24-pin header
Page 16
CN Pinou
The ATX power co
ts:
See Table 3-3
nnector connects to an ATX power supply.
Page 31
IMB-C2060 microATX Motherboard
Figure 3-2: ATX Power Connector Location
Pin Description Pin Description
1 +3.3 V 13 +3.3 V
2 +3.3 V 14 -12 V
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3. GND 15 GND
4 +5 V 16 PS-ON5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWRGD_PS 20 NC
9 +5VSB 21 +5 V
10 +12V 22 +5 V
11 +12V 23 +5 V
12 +3.3V 24 GND
Table 3-3: ATX Power Connector Pinouts
Page 17
Page 32
3.2.2 Battery Connector
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Only
certified engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local
regulations.
CN Label: BAT1
IMB-C2060 microATX Motherboard
CN Type:
CN Location:
CN Pinou
This is
retain the time when power is turned off.
ts:
connected to the system battery. The battery provides power to the system clock to
Battery holder
See Figure 3-3
See Table 3-4
Page 18
Figure 3-3: Battery Connector Location
Page 33
IMB-C2060 microATX Motherboard
Pin Description
1 NC
2 BAT+
3 BAT-(GND)
Table 3-4: Battery Connector Pinouts
3.2.3 CPU Fan Connector
CN Label: CPU_FAN
CN Type:
CN Location:
CN Pinouts:
4-pin wafer
See Figure 3-4
See Table 3-5
The fan connector attaches to a CPU cooling fan.
Figure 3-4: CPU Fan Connector Location
PIN NO. DESCRIPTION
1 GND
2 +12 V
3 FANIN
4 FANOUT
Table 3-5: CPU Fan Connector Pinouts
Page 19
Page 34
3.2.4 CPU Power Connector
CN Label: CPU12V1
IMB-C2060 microATX Motherboard
CN Type:
CN Location:
CN Pinouts:
The CPU power input connector provides power to the CPU.
4-pin connector
See Figure 3-5
See Table 3-6
Figure 3-5: CPU Power Connector Location
PIN NO. DESCRIPTION
1 GND
2 GND
3 +12V
4 +12V
Table 3-6: CPU Power Connector Pinouts
3.2.5 Digital I/O Connector
CN Label: DIO1
CN Type:
CN Location:
CN Pinouts:
26-pin header
See Figure 3-6
See Table 3-7
Page 20
Page 35
IMB-C2060 microATX Motherboard
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 12-bit output and 12-bit input.
Figure 3-6: Digital I/O Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 +5V
3 D_IN0 4 D_OUT0
5 D_IN1 6 D_OUT1
7 D_IN2 8 D_OUT2
9 D_IN3 10 D_OUT3
11 D_8IN0 12 D_8OUT0
13 D_8IN1 14 D_8OUT1
15 D_8IN2 16 D_8OUT2
17 D_8IN3 18 D_8OUT3
19 D_8IN4 20 D_8OUT4
21 D_8IN5 22 D_8OUT5
23 D_8IN6 24 D_8OUT6
25 D_8IN7 26 D_8OUT7
Table 3-7: Digital I/O Connector Pinouts
Page 21
Page 36
3.2.6 Front Panel Audio Connector
CN Label: FP_AUDIO
IMB-C2060 microATX Motherboard
CN Type:
CN Location:
CN Pinou
This
ts:
connector connects to speakers, a microphone and an audio input.
10-pin header
See Figure 3-7
See Table 3-8
Figure 3-7: Front Panel Audio Connector Location
Pin Description Pin Description
1 MIC_L 2 Audio GND
3 MIC_R 4 FP_AUO DETECT
5 Line_R 6 PD
7 F_SENSE 8 NC
9 Line_L 10 PD
Table 3-8: Front Panel Audio Connector Pinouts
3.2.7 Front Panel Connector
CN Label: F_PANEL
14-pin header
Page 22
CN Type:
Page 37
IMB-C2060 microATX Motherboard
CN Location:
CN Pinouts:
See Figure 3-8
See Table 3-9
The front panel connector connects to the indicator LEDs and buttons on the computer's
front panel.
Figure 3-8: Front Panel Connector Location
FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION
Power LED 1 Power LED Speaker 2 Beep Power
3 NC 4 NC
5 GND 6 NC
Power Button 7 PWRBTSW# 8 PC Beep
9 GND Reset 10 NC
HDD LED 11 HDDLED 12 EXTRST#
13 HDDLED# 14 GND
Table 3-9: Front Panel Connector Pinouts
3.2.8 FW Programming
CN Label: CN1
CN Type:
8-pin header
Page 23
Page 38
IMB-C2060 microATX Motherboard
CN Location:
CN Pinou
The FW Prog
Figure 3-9: FW Programming Connector Location
ts:
See Figure 3-9
See Table 3-10
ramming connector is used for programming the firmware.
Pin Description Pin Description
1 +3.3V 2 TDO
3 TDI 4 NC
5 NC 6 TMS
7 GND 8 TCK
Table 3-10: FW Programming Connector Pinouts
3.2.9 Infrared Interface Connector
CN Label: IR1
CN Type:
CN Location:
CN Pinou
The infra
ts:
red connector attaches to an infrared receiver for use with remote cont rols.
5-pin header
See Figure 3-10
See Table 3-11
Page 24
Page 39
IMB-C2060 microATX Motherboard
Figure 3-10: Infrared Connector Location
Pin Description
1 +5V
2 NC
3 IR_RX
4 GND
5 IR_TX
Table 3-11: Infrared Connector Pinouts
3.2.10 Memory Card Slot
CN Label: DIMM1, DIMM2
CN Type:
CN Location:
The DIMM slots are for DIMM memory modules.
DDR3 DIMM slot
See 6Figure 3-11
Page 25
Page 40
IMB-C2060 microATX Motherboard
Figure 3-11: Memory Card Slot Location
3.2.11 PCH Fan Connector
CN Label: PCH_FAN
CN Type:
CN Location:
CN Pinou
The PCH fan con
ts:
3-pin wafer
See Figure 3-12
See Table 3-12
nector attaches to a PCH cooling fan.
Page 26
Page 41
IMB-C2060 microATX Motherboard
Figure 3-12: PCH Fan Connector Location
Pin Description
1 FANIN
2 +12V
3 GND
Table 3-12: PCH Fan Connector Pinouts
3.2.12 PCI Express Power
CN Label: PCIE_POWER
CN Type:
CN Location:
CN Pinou
Provide
ts:
s extra power to the PCIe x16 card.
4-pin connector
See Figure 3-13
See Table 3-13
Page 27
Page 42
Figure 3-13: PCIe Power Location
IMB-C2060 microATX Motherboard
Pin Description
1 VCC +5V
2 GND
3 GND
4 VCC +12V
Table 3-13: PCIe Power Pinouts
3.2.13 SATA 3Gb/s Drive Connectors
CN Label: SATA3, SATA4, SATA5, SATA6
CN Type:
CN Location:
CN Pinou
The SATA dri
ts:
7-pin SATA connector
See Figure 3-14
See Table 3-14
ve connectors can be connected to SATA drives.
Page 28
Page 43
IMB-C2060 microATX Motherboard
Figure 3-14: SATA 3Gb/s Drive Connector Locations
Pin Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
Table 3-14: SATA 3Gb/s Drive Connector Pinouts
3.2.14 SATA 6Gb/s Drive Connectors
CN Label: SATA1, SATA2
CN Type:
7-pin SATA drive connectors
CN Location:
CN Pinouts:
See Figure 3-15
See Table 3-15
The SATA drive connectors can be connected to SATA drives.
Page 29
Page 44
IMB-C2060 microATX Motherboard
Figure 3-15: SATA 6Gb/s Drive Connector Locations
Pin Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
Table 3-15: SATA 6Gb/s Drive Connector Pinouts
3.2.15 Serial Port Connector, RS-422/485
CN Label: COM2
CN Type:
CN Location:
CN Pinouts:
4-pin wafer
See Figure 3-16
See Table 3-16
Page 30
Used for RS-422/485 communications.
Page 45
IMB-C2060 microATX Motherboard
Figure 3-16: RS-422/485 Connector Location
PIN NO. DESCRIPTION
1 RXD4222 RXD422+
3 TXD422+/TXD485+
4 TXD422-/TXD485-
Table 3-16: RS-422/485 Connector Pinouts
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9
connector are listed below.
RS-422 Pinouts RS-485 Pinouts
Table 3-17: DB-9 RS-422/485 Pinouts
3.2.16 Serial Port Connectors, RS-232
CN Label: COM3-6, COM7-10
CN Type:
40-pin box header
Page 31
Page 46
IMB-C2060 microATX Motherboard
CN Location:
CN Pinouts:
See Figure 3-17
See Table 3-18
Each of these connectors provides RS-232 connections.
Figure 3-17: Serial Port Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 NDCD3# 2 NDSR3#
3 NRXD3 4 NRTS3#
5 NTXD3 6 NCTS3#
7 NDTR3# 8 NRI3#
9 GND 10 GND
11 NDCD4# 12 NDSR4#
13 NRXD4 14 NRTS4#
15 NTXD4 16 NCTS4#
17 NDTR4# 18 NRI4#
19 GND 20 GND
21 NDCD5# 22 NDSR5#
23 NRXD5 24 NRTS5#
25 NTXD5 26 NCTS5#
27 NDTR5# 28 NRI5#
29 GND 30 GND
31 NDCD6# 32 NDSR6#
Page 32
Page 47
IMB-C2060 microATX Motherboard
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
33 NRXD6 34 NRTS6#
35 NTXD6 36 NCTS6#
37 NDTR6# 38 NRI6#
39 GND 40 GND
Table 3-18: COM3~6 Serial Port Connector Pinouts
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 NDCD7# 2 NDSR7#
3 NRXD7 4 NRTS7#
5 NTXD7 6 NCTS7#
7 NDTR7# 8 NRI7#
9 GND 10 GND
11 NDCD8# 12 NDSR8#
13 NRXD8 14 NRTS8#
15 NTXD8 16 NCTS8#
17 NDTR8# 18 NRI8#
19 GND 20 GND
21 NDCD9# 22 NDSR9#
23 NRXD9 24 NRTS9#
25 NTXD9 26 NCTS9#
27 NDTR9# 28 NRI9#
29 GND 30 GND
31 NDCD10# 32 NDSR10#
33 NRXD10 34 NRTS10#
35 NTXD10 36 NCTS10#
37 NDTR10# 38 NRI10#
39 GND 40 GND
Table 3-19: COM7~10 Serial Port Connector Pinouts
Page 33
Page 48
3.2.17 SMBus Connector
CN Label: SMBUS_1
IMB-C2060 microATX Motherboard
CN Type:
CN Location:
CN Pinouts:
The SMBus (System Management Bus) connector provides low-speed system
management communications.
4-pin wafer
See Figure 3-18
See Table 3-20
Page 34
Figure 3-18: SMBus Connector Location
PIN DESCRIPTION
1 +5V_DUAL
2 SMBCLK
3 SMBDATA
4 GND
Table 3-20: SMBus Connector Pinouts
Page 49
IMB-C2060 microATX Motherboard
3.2.18 SPDIF Connector
CN Label: SPDIF
CN Type:
CN Location:
CN Pinouts:
Use the SPDIF connector to connect digital audio devices to the system.
5-pin header
See Figure 3-19
See Table 3-21
Figure 3-19: SPDIF Connector Location
PIN DESCRIPTION
1 +5V
2 NC
3 SPDIFOUT
4 GND
5 SPDIFIN
Table 3-21: SPDIF Connector Pinouts
3.2.19 SPI Connector
CN Label: SPI1
CN Type:
8-pin header
Page 35
Page 50
IMB-C2060 microATX Motherboard
CN Location:
CN Pinouts:
The SPI connector is used to flash the BIOS.
Figure 3-20: SPI Connector Location
See Figure 3-20
See Table 3-22
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +SPI_VCC 2 GND
3 SPI_CS0#_CN 4 SPI_CLK0_CN
5 SPI_SO0_CN 6 SPI_SI0_CN
7 NC 8 NC
Table 3-22: SPI Connector Pinouts
3.2.20 System Fan Connectors
CN Label: SYS_FAN1, SYS_FAN2
CN Type:
CN Location:
CN Pinouts:
The fan connector attaches to a cooling fan.
3-pin wafer
See Figure 3-21
See Table 3-23
Page 36
Page 51
IMB-C2060 microATX Motherboard
Figure 3-21: System Fan Connector Locations
PIN NO. DESCRIPTION
1 NC
2 +12 V
3 GND
Table 3-23: System Fan Connector Pinouts
3.2.21 TPM Connector
CN Label: TPM1
CN Type:
CN Location:
CN Pinouts:
The TPM connector connects to a TPM module.
20-pin header
See Figure 3-22
See Table 3-24
Page 37
Page 52
IMB-C2060 microATX Motherboard
Figure 3-22: TPM Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 TPMCLK 2 GND
3 LFRAME- 4 NC
5 PCIRST4- 6 +5V
7 LAD3 8 LAD2
9 LAD0 10 LAD1
11 GND 12 GND
13 SMBCLK_MAIN 14 SMBDATA_MAIN
15 +3.3V 16 SERIRQ
17 GND 18 CLKRUN19 +3.3V 20 LDRQ0-
Table 3-24: TPM Connector Pinouts
3.2.22 USB Connectors
CN Label: USB1, USB2, USB3, USB4
CN Type:
8-pin header
Page 38
CN Location:
CN Pinouts:
See Figure 3-23
See Table 3-25 ~ Table 3-28
Page 53
IMB-C2060 microATX Motherboard
The USB connectors connect to USB devices. Each pin header provides two USB ports.
Figure 3-23: USB Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 2 GND
3 USB20_C_N2 4 USB20_C_P3
5 USB20_C_P2 6 USB20_C_N3
7 GND 8 +5V
Table 3-25: USB1 Connector Pinouts
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 2 GND
3 USB20_C_N10 4 USB20_C_P11
5 USB20_C_P10 6 USB20_C_N11
7 GND 8 +5V
Table 3-26: USB2 Connector Pinouts
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 2 GND
3 USB20_C_N12 4 USB20_C_P13
5 USB20_C_P12 6 USB20_C_N13
Page 39
Page 54
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
7 GND 8 +5V
Table 3-27: USB3 Connector Pinouts
IMB-C2060 microATX Motherboard
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 2 GND
3 USB20_C_N8 4 USB20_C_P9
5 USB20_C_P8 6 USB20_C_N9
7 GND 8 +5V
Table 3-28: USB4 Connector Pinouts
3.3 External Peripheral Interface Connector Panel
The figure below shows the external peripheral interface connector (EPIC) panel. The
EPIC panel consists of the following:
Figure 3-24: External Peripheral Interface Connector
3.3.1 Audio Connector
Page 40
CN Label: AUDIO_JACK
CN Type:
Audio jack
Page 55
IMB-C2060 microATX Motherboard
CN Location:
See Figure 3-24
The audio jacks connect to external audio devices.
Line In port (Light Blue): Connects a CD-ROM, DVD player, or other audio
devices.
Line Out port (Lime): Connects to a head phone or a speaker. With
multi-channel configurations, this port can also connect to front speakers.
Microphone (Pink): Connects a microphone.
Figure 3-25: Audio Connector
3.3.2 Keyboard/Mouse Connector
CN Label: KBMS
CN Type:
CN Location:
CN Pinouts:
The PS/2 ports are for connecting a PS/2 mouse and a PS/2 keyboard.
PIN DESCRIPTION PIN DESCRIPTION
1 KB_DATA 8 NC
2 NC 9 GND
3 GND 10 KBPWR
4 KBPWR 11 MS_CLK
Dual PS/2
See Figure 3-24
See Table 3-29
5 KB_CLK 12 NC
Page 41
Page 56
PIN DESCRIPTION PIN DESCRIPTION
6 NC 13 KB_GND
7 MS_DATA 14 KB_GND
Table 3-29: PS/2 Connector Pinouts
3.3.3 Ethernet and USB Connector
CN Label: LAN1_USB, LAN2_USB
IMB-C2060 microATX Motherboard
CN Type:
CN Location:
CN Pinouts:
RJ-45, USB
See Figure 3-24
See Table 3-30 and Table 3-31
The LAN connector connects to a local network.
PIN DESCRIPTION PIN DESCRIPTION
1 1.9V_LAN1/
1.05V_LAN2
3 TRD1/2N0 4 TRD1/2P1
5 TRD1/2N1 6 TRD1/2P2
7 TRD1/2N2 8 TRD1/2P3
9 TRD1/2N3 10 GND
11 L1/2_LINK_100# 12 L1/2_LINK_1000#
13 L1/2_LINK_ACT# 14 3.3V_LAN/LAN1
2 TRD1/2P0
Table 3-30: LAN Pinouts
Page 42
The USB connector can be connected to a USB device.
PIN DESCRIPTION PIN DESCRIPTION
1 USBPWR1/2 2 USBDATA0/83 USBDATA0/8+ 4 GND
5 USBPWR1/2 6 USBDATA1/97 USBDATA1/9+ 8 GND
Table 3-31: USB Port Pinouts
Page 57
IMB-C2060 microATX Motherboard
3.3.4 HDMI Port Connector
CN Label: HDMI
CN Type:
CN Location:
CN Pinouts:
HDMI connector
See Figure 3-24
See Table 3-32
The HDMI port connects to an HDMI device.
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 HDMI_TMDS_C_DATA2 13 NC
2 GND 14 NC
3 HDMI_TMDS_C_DATA2# 15 HDMI_DDC_SCLK
4 HDMI_TMDS_C_DATA1 16 HDMI_DDC_SDATA
5 GND 17 GND
6 HDMI_TMDS_C_DATA1# 18 +5V
7 HDMI_TMDS_C_DATA0 19 HDMI_HPD
8 GND 20 GND
9 HDMI_TMDS_C_DATA0# 21 GND
10 HDMI_TMDS_C_CLK 22 GND
11 GND 23 GND
12 HDMI_TMDS_C_CLK#
Table 3-32: HDMI Connector Pinouts
3.3.5 Serial Port Connectors (COM1)
CN Label: COM1
CN Type:
CN Location:
CN Pinouts:
The serial port connects to a RS-232 serial communications device.
DB-9 connector
See Figure 3-24
See Table 3-33
Page 43
Page 58
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 NDCD1# 6 NDSR1#
2 NRXD1 7 NRTS1#
3 NTXD1 8 NCTS1#
4 NDTR1# 9 NRI1#
5 GND
IMB-C2060 microATX Motherboard
Table 3-33: Serial Port Connector Pinouts
Figure 3-26: Serial Port Connector Pinouts
3.3.6 VGA and DVI Connector
CN Label: DVI+CRT
CN Type:
CN Location:
CN Pinouts:
The VGA connector connects to a monitor that accepts a standard VGA input.
PIN DESCRIPTION PIN DESCRIPTION
1 CRT_RED 2 CRT_GREEN
3 CRT_BLUE 4 NC
5 GND 6 GND
7 GND 8 GND
15-pin Female, 24-pin header
See Figure 3-24
See Table 3-34 and Table 3-35
Page 44
9 +5V CRT 10 CRT_PLUG#
11 NC 12 CRT_DDC_DATA
13 CRT_HSYNC 14 CRT_VSYNC
Page 59
IMB-C2060 microATX Motherboard
PIN DESCRIPTION PIN DESCRIPTION
15 CRT_DDC_CLK
Table 3-34: VGA Connector Pinouts
Figure 3-27: VGA Connector
The DVI connector connects to a monitor that supports DVI video input.
PIN DESCRIPTION PIN DESCRIPTION
1 DVI_TMDS_C_DATA2# 2 DVI_TMDS_C_DATA2
3 GND 4 NC
5 NC 6 DVI_DDC_SCLK
7 DVI_DDC_SDATA 8 NC
9 DVI_TMDS_C_DATA1# 10 DVI_TMDS_C_DATA1
11 GND 12 NC
13 NV 14 +5V_DVI
15 GND 16 DVI_HPD
17 DVI_TMDS_C_DATA0# 18 DVI_TMDS_C_DATA0
19 GND 20 NC
21 NC 22 GND
23 DVI_TMDS_C_CLK 24 DVI_TMDS_C_CLK#
Table 3-35: DVI Connector Pinouts
Page 45
Page 60
IMB-C2060 microATX Motherboard
Chapter
4
4 Installation
Page 46
Page 61
IMB-C2060 microATX Motherboard
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
IMB-C2060 may result in permanent damage to the IMB-C2060 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the IMB-C2060. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the IMB-C2060 or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the IMB-C2060, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
IMB-C2060.
Only handle the edges of the PCB:-: When handling the PCB, hold the PCB
by the edges.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices must
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage and injury to the person performing the installation.
Page 47
Page 62
IMB-C2060 microATX Motherboard
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the components and
injury to the user.
Before and during the installation please DO the following:
Read the user manual:
o The user manual provides a complete description of the IMB-C2060
installation instructions and configuration options.
Wear an electrostatic discharge cuff (ESD):
o Electronic components are easily dama ged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place the IMB-C2060 on an antistatic pad:
o When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power to the IMB-C2060 off:
o When working with the IMB-C2060, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the IMB-C2060 DO NOT:
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
Use the product before verifying all the cables and power connectors are
properly connected.
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
Page 48
Page 63
IMB-C2060 microATX Motherboard
4.2.1 Socket LGA1155 CPU Installation
NOTE:
To enable Hyper-Threading, the CPU and chipset must both support it.
WARNING:
CPUs are expensive and sensitive components. When installing the
CPU please be careful not to damage it in anyway. Make sure the CPU
is installed properly and ensure the correct cooling kit is properly
installed.
The LGA1155 socket is shown in Figure 4-1.
Figure 4-1: Intel LGA115 5 Socket
To install the CPU, follow the steps below.
WARNING:
DO NOT touch the pins at the bottom of the CPU. When handling the
CPU, only hold it on the sides.
Page 49
Page 64
Step 1: Remove the protective cover. The black protective cover can be removed by
pulling up on the tab labeled "Remove". See Figure 4-2.
Figure 4-2: Remove Protective Cover
Step 2: Open the socket. Disengage the load lever by pressing the lever down and
IMB-C2060 microATX Motherboard
slightly outward to clear the retention tab. Fully open the lever, then open the
load plate. See Figure 4-3.
Figure 4-3: CPU Socket Load Plate
Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
Page 50
compressed air.
Page 65
IMB-C2060 microATX Motherboard
Step 4: Orientate the CPU properly. The contact array should be facing the CPU
socket.
Step 5: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the
CPU socket.
Step 6: Align the CPU pins. Locate pin 1 and the two orientation notches on the CPU.
Carefully match the two orientation notches on the CPU with the socket
alignment keys.
Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are
properly aligned, the CPU should slide into the CPU socket smoothly. See
Figure 4-4.
Figure 4-4: Insert the Socket LGA1155 CPU
Step 8: Close the CPU socket. Close the load plate and engage the load lever by
pushing it back to its original position. There will be some resist ance, but will not
require extreme pressure.
Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power
supply to the board. Step 0:
Page 51
Page 66
IMB-C2060 microATX Motherboard
4.2.2 Socket LGA1155 Cooling Kit Installation
WARNING:
DO NOT attempt to install a push-pin cooling fan.
The pre-installed support bracket prevents the board from
bending and is ONLY compatible with captive screw type cooling
fans.
Figure 4-5: Cooling Kits (CF-1156A-RS and CF-1156E-RS)
The cooling kit can be bought from IEI. The cooling kit has a heatsink and fan.
WARNING:
Do not wipe off (accidentally or otherwise) the pre-sprayed layer of
thermal paste on the bottom of the heat sink. The thermal paste
between the CPU and the heat sink is important for optimum heat
dissipation.
To install the cooling kit, follow the instructions below.
Step 1: A cooling kit bracket is pre -install ed on solder side of the mainboard. See Figure
4-6.
Page 52
Page 67
IMB-C2060 microATX Motherboard
Figure 4-6: Cooling Kit Support Bracket
Step 2: Place the cooling kit onto the socket LGA1155 CP U. Make sure the CPU
cable can be properly routed when the cooling kit is installed.
Step 3: Mount the cooling kit. Gently place the cooling kit on top of the CPU. Make
sure the four threaded screws on the corners of the cooling kit properly pass
through the holes of the cooling kit bracket.
Step 4: Secure the cooling kit by fastening the four retention screws of the cooling kit.
Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the IMB-C2060. Carefully route the cable and avoid heat generating chips
and fan blades.
Page 53
Page 68
4.2.3 DIMM Installation
To install a DIMM, please follow the steps below and refer to Figure 4-7.
IMB-C2060 microATX Motherboard
Figure 4-7: DIMM Installation
Step 1: Open the DIMM socket handles. Open the two handles outwards as far as
they can. See Figure 4-7.
Step 2: Align the DI
lines up with the notch on the memory socket. See Figure 4-7.
Step 3: Insert the DI
Clip the two handles into place. See Figure 4-7.
Step 4: Rem
oving a DIMM. To remove a DIMM, push both handles outward. The
memory module is ejected by a mechanism in the socket.Step 0:
MM with the socket. Align the DIMM so the notch on the memory
MM. Once aligned, press down until the DIMM is properly seated.
Page 54
Page 69
IMB-C2060 microATX Motherboard
4.3 Jumper Settings
NOTE:
A jumper is a metal bridge used to close
an electrical circuit. It consists of two or
three metal pins and a small metal clip
(often protected by a plastic cover) that
slides over the pins to connect them. To
CLOSE/SHORT a jumper means
connecting the pins of the jumper with
the plastic clip and to OPEN a jumper means removing the plastic clip
from a jumper.
The hardware jumpers must be set before installation. Jumpers are shown in Table 4-1.
Description Label Type
AT/ATX mode select jumper JATX_AT1 2-pin header
Clear CMOS jumper J_CMOS2 3-pin header
ME Debug connector J_FLASH1 3-pin header
USB power select jumper USB_PWR1 3-pin header
Wake-on LAN WOL_SEL1 3-pin header
Table 4-1: Jumpers
4.3.1 AT/ATX Power Mode Jumper
Jumper Label: JATX_AT1
Jumper Type:
Jumper Settings:
2-pin header
See Table 4-2
Jumper Location:
The AT Power Select jumper specifies the systems power mode as AT or ATX.
See Figure 4-8
Page 55
Page 70
Setting Description
Closed ATX power (Default)
Open AT power
Table 4-2: AT/ATX Power Mode Jumper Settings
IMB-C2060 microATX Motherboard
Figure 4-8: AT/ATX Power Mode Jumper Location
4.3.2 Clear CMOS Jumper
Jumper Label: J_CMOS2
Jumper Type:
Jumper Settings:
Jumper Location:
To reset the BIOS, move the jumper to the "Clear BIOS" position for 3 seconds or more,
and then move back to the default position.
Setting Description
Short 1-2 Normal (Default)
Short 2-3 Clear BIOS
3-pin header
See Table 4-3
See Figure 4-9
Page 56
Table 4-3: Clear BIOS Jumper Settings
Page 71
IMB-C2060 microATX Motherboard
Figure 4-9: Clear BIOS Jumper Location
4.3.3 ME Debug Jumper
CN Label: J_FLASH1
CN Type:
CN Location:
CN Pinouts:
The ME Debug connector allows ME firmware overwrite protection.
3-pin header
See Figure 4-10
See Table 4-4
Figure 4-10: ME Debug Jumper Location
Page 57
Page 72
PIN NO. DESCRIPTION
Short 1-2 Overwrite disable (Default)
Short 2-3 Overwrite enable
Table 4-4: ME Debug Jumper Settings
4.3.4 USB Power Select Jumper
Jumper Label: USB_PWR1
IMB-C2060 microATX Motherboard
Jumper Type:
Jumper Settings:
Jumper Loc
The USB po
Setting Description
Short 1-2 5V (Default)
Short 2-3 5VSB
ation:
wer connector allows the user to select the USB power setting.
3-pin header
See Table 4-5
See Figure 4-11
Table 4-5: USB Power Select Jumper Settings
Page 58
Figure 4-11: USB Power Select Jumper Location
Page 73
IMB-C2060 microATX Motherboard
4.3.5 Wake-on LAN Jumper
CN Label: WOL_SEL1
CN Type:
CN Location:
CN Pinouts:
The Wake-on LAN connector allows the user to enable or disable the Wake-o n LAN (WOL)
function.
3-pin header
See Figure 4-12
See Table 4-6
Figure 4-12: Wake-on LAN Jumper Location
PIN NO. DESCRIPTION
Short 1-2 Wakeup Enable (Default)
Short 2-3 Disable
Table 4-6: Wake-on LAN Jumper Settings
Page 59
Page 74
IMB-C2060 microATX Motherboard
4.4 Internal Peripheral Device Connections
This section outlines the installation of peripheral devices to the onboard connectors.
4.4.1 SATA Drive Connection
The IMB-C2060 is shipped with four SATA drive cables. To connect the SATA drives to
the connectors, please follow the steps below.
Step 1: Locate the connectors. The locations of the SATA drive connectors are shown
in Chapter 3.
Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector. See Figure 4-13.
Page 60
Figure 4-13: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SAT A drive. See Figure 4-14.
Step 4: Conn
ect the SA TA power cable (optional). Connect the SA TA power
connector to the back of the SATA drive. See Figure 4-14.
Page 75
IMB-C2060 microATX Motherboard
Figure 4-14: SATA Power Drive Connection
The SATA power cable can be bought from IEI. See Optional Items in Section 2.4.
4.5 External Peripheral Interface Connection
This section describes connecting devices to the external connectors on the IMB-C2060.
4.5.1 Audio Connector
The audio jacks on the external audio connector enable the IMB-C2060 to be connected
to a stereo sound setup. Each jack supports both input and output. When connecting a
device, the High Definition Audio utility will automatically detect input or output. The lime
green (top) audio jack does not support input from a microphone. To install the audio
devices, follow the steps below.
Step 1: Identify the audio plugs. The plugs on your home theater system or speakers
may not match the colors on the rear panel.
Page 61
Page 76
Step 2: Plug the audio plugs into the audio jacks. Plug the audio plugs into the audio
jacks. If the plugs on your speakers are different, an adapter will need to be used
to plug them into the audio jacks.
IMB-C2060 microATX Motherboard
Figure 4-15: Audio Connector
Step 3: Check audio clarity. Check that the sound is coming through the right speakers
by adjusting the balance front to rear and left to right.
4.5.2 LAN Connection
There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection
to an external network. To connect a LAN cable with an RJ-45 connector, please follow
the instructions below.
Step 1: Locate the RJ-45 connectors. The locations of the USB connectors are shown
in Chapter 4.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
the RJ-45 connectors on the IMB-C2060. See Figure 4-16.
Page 62
Page 77
IMB-C2060 microATX Motherboard
Figure 4-16: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector. Step 0:
4.5.3 Parallel Device Connection
The IMB-C2060 has a single female DB-25 connector on the external peripheral interface
panel for parallel devices. Follow the steps below to connect a parallel device to the
IMB-C2060.
Step 1: Locate the DB-25 connector. The location of the DB-25 conne ctor is shown in
Chapter 3.
Step 2: Insert the DB-25 connector. Insert the DB-25 connector of a parallel device
into the DB-25 connector on the external peripheral interface. See Figure 4-17.
Page 63
Page 78
Figure 4-17: Parallel Device Connector
IMB-C2060 microATX Motherboard
Step 3: Secure the connector. Secure the DB-25 connector to the external interface by
tightening the two retention screws on either side of the connector. Step 0:
4.5.4 PS/2 Keyboard and Mouse Connection
The IMB-C2060 has a dual PS/2 connector on the external peripheral interface panel. The
dual PS/2 connector is used to connect to a keyboard and mouse to the system. Follow
the steps below to connect a keyboard and mouse to the IMB-C2060.
Step 1: Locate the dual PS/2 connector. The location of the dual PS/2 connector is
shown in Chapter 3.
Step 2: Insert the keyboard/mouse connector. Insert a PS/2 keyboard or mouse
connector into the appropriate PS/2 connector on the external peripheral
interface connector . See Figure 4-18.
Page 64
Page 79
IMB-C2060 microATX Motherboard
Figure 4-18: PS/2 Keyboard/Mouse Connector
4.5.5 Serial Device Connection
The IMB-C2060 has a single female DB-9 connector on the external peripheral interface
panel for a serial device. Follow the steps below to connect a serial device to the
IMB-C2060.
Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in
Chapter 3.
Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on the external peripheral interface. See Figure 4-19.
Page 65
Page 80
IMB-C2060 microATX Motherboard
Figure 4-19: Serial Device Connector
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
4.5.6 USB Connection (Dual Connector)
The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices. Follow the steps below to connect USB devices to the IMB-C2060.
Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB
Series "A" receptacle connectors are shown in Chapter 3.
Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See
Figure 4-20.
Step 0:
Page 66
Page 81
IMB-C2060 microATX Motherboard
Figure 4-20: USB Connector
4.5.7 VGA Monitor Connection
The IMB-C2060 has a single female DB-15 connector on the external peripheral interface
panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor
to the IMB-C2060, please follow the instructions below.
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Step 3: Insert the VGA connector. Once the connectors are properly ali gned with the
insert the male connector from the VGA screen into the female connector on the
IMB-C2060. See Figure 4-21.
Page 67
Page 82
Figure 4-21: VGA Connector
IMB-C2060 microATX Motherboard
Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
4.6 Intel® AMT Setup Procedure
The IMB-C2060 is featured with the Intel® Active Management Technology (AMT). To
enable the Intel® AMT function, follow the steps below.
Step 1: Make sure the CHA_DIMM1 socket is installed with one DDR3 DIMM.
Step 2: Connect an Ethernet cable to the RJ-45 connector labeled LAN2.
Step 3: The AMI BIOS options regarding the Intel® ME or Intel® AMT must be enabled,
Step 4: Properly install the Intel® Management Engine Components drivers from the
iAMT Driver & Utility directory in the driver CD. See Section 6.8.
Step 5: Config
ure the Intel® Management Engine BIOS extension (MEBx). To get into
Page 68
the Intel® MEBx settings, press <Ctrl+P> after a single beep during boot-up
Page 83
IMB-C2060 microATX Motherboard
process. Enter the Intel® current ME password as it requires (the Intel® default
password is admin).
NOTE:
To change the password, enter a new password following the strong
password rule (containing at least one upper case letter, one lower
case letter, one digit and one special character, and be at least eight
characters).
Page 69
Page 84
IMB-C2060 microATX Motherboard
Chapter
5
5 BIOS
Page 70
Page 85
IMB-C2060 microATX Motherboard
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the F2 or D
2. Press the F2 or D
appears on the screen. 0.
If the message disappears before the F2
and try again.
ELETE key as soon as the system is turned on or
ELETE key when the “Press F2 to enter SETUP” message
OR DELETE key is pressed, restart the computer
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press E
keys are shown in.
Key Function
Up arrow Move to previous item
Down arrow Move to next item
Left arrow Move to the item on the left hand side
SC to quit. Navigation
Right arrow Move to the item on the right hand side
+ Increase the numeric value or make changes
- Decrease the numeric value or make changes
Page Up key Increase the numeric value or make change s
Page Dn key Decrease the numeric value or ma ke changes
Page 71
Page 86
Key Function
Esc key Main Menu – Quit and not save changes into CMOS
F1 key General help, only for Status Page Setup Menu and Option
F2 key Load previous values
F3 key Load optimized defaults
F4 key Save changes and Exit BIOS
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
IMB-C2060 microATX Motherboard
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Page Setup Menu
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press E
the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 4.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main – Changes the basic system configuration.
Advanced – Changes the advanced system settings.
Chipset – Changes the chipset settings.
Boot – Changes the system boot configuration.
Security – Sets User and Supervisor Passwords.
SC or
Page 72
Save & Exit – Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 87
IMB-C2060 microATX Motherboard
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.3-0.19
Compliency UEFI 2.3; PI 1.2
Project Version SA38AR36.ROM
Build Date 11/15/2013 15:22:05
Processor Information
Name SandyBridge
Brand String Intel(R) Celeron(R) C
Frequency 1600 MHz
Processor ID 206a7
Stepping D2
Number of Processors 1Core(s) / 1Thread(S)
Microcode Revision 28
GT Info GT2 (1000 MHz)
IGFX VBIOS Version 2137
Memory RC Version 1.2.2.0
Total Memory 2048 MB (DDR3 1067)
Memory Frequency 1067 Mhz
PCH Information
Name CougarPoint
Stepping 05/B3
TXT Capability of Platform/PCH Unsupported
LAN PHY Revision C0
ME FW Version 8.0.4.1441
ME Firmware SKU 5MB
SPI Clock Frequency
D0FR Support Supported
Read Status Clock Frequency 33 MHz
Write Status Clock Frequency 33 MHz
Fast Read Status Clock Frequency 33 MHz
System Date [Tue 10/03/2014]
System Time [15:10:27]
Access Level Administrator
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Set the Date. Use Tab to
switch between Data
elements.
----------------------
: Select Screen
: Select Item
Enter Select
+ -: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 1: Main
Page 73
Page 88
The System Overview field also has two user configurable fields:
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
IMB-C2060 microATX Motherboard
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Page 74
Page 89
I
IMB-C2060 microATX Motherboard
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> Trusted Computing
> CPU Configuration
> SATA Configuration
> Intel TXT(LT) Configuration
> AMT Configuration
> USB Configuration
> F81216 Second Super IO Configuration
> F81866 Super IO Configuration
> F81866 H/M Monitor
> Serial Port Console Redirection
> IEI Feature
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 2: Advanced
Trusted Computing
Settings
----------------------
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
: Select Screen
5.3.1 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 3) to configure settings related to the
Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
TPM Configuration
Security Device Support [Disable]
Current Status Information
NO Security Device Found
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
NT1A interface will not
be available.
----------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 3: Trusted Computing
Page 75
Page 90
Security Device Support [Disable]
Use the Security Device Support option to configure support for the security device.
IMB-C2060 microATX Motherboard
Disable DEFAULT
Enable
Security device support is disabled.
Security device support is enabled.
5.3.2 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 4) to enter the CPU Information
submenu or enable Intel Virtualization Technology.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Configuration
> CPU Information
Intel Virtualization Technology [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
----------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 4: CPU Configuration
Intel® Virtualization Technology [Disabled]
Use the Intel® Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel Virtualization technology allows
several OSs to run on the same system at the same time.
Disabled DEFAULT
Enabled
Page 76
Disables Intel Virtualization
Technology.
Enables Intel Virtualization Technology.
Page 91
IMB-C2060 microATX Motherboard
5.3.2.1 CPU Information
Use the CPU Information submenu (BIOS Menu 5) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Celeron(R) CPU G440 @ 1.60GHz
CPU Signature 206a7
Microcode Patch 28
Max CPU Speed 1600 MHz
Min CPU Speed 1600 MHz
CPU Speed 1600 MHz
Processor Cores 1
Intel HT Technology Not Supported
Intel VT-x Technology Supported
Intel SMX Technology Not Supported
64-bit Supported
L1 Data Cache 32 kB x 1
L1 Code Cache 32 kB x 1
L2 Cache 256 kB x 1
L3 Cache 1024 kB
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
----------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 5: CPU Information
The CPU Configuration menu (BIOS Menu 5) li
Processor Type: Lists the brand name of the CPU being used
CPU Signature: Lists the CPU signature value.
Microcode Patch: Lists the microcode patch being used.
Max CPU Speed: Lists the maximum CPU processing speed.
Min CPU Speed: Lists the minimum CPU processing speed.
Processor Cores: Lists the number of the processor core
Intel HT Technology: Indicates if Intel HT Technology is supported by the
CPU.
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
sts the following CPU details:
Page 77
Page 92
64-bit: Indicates if 64-bit OS is supported by the CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
L2 Cache: Lists the amount of storage space on the L2 cache.
L3 Cache: Lists the amount of storage space on the L3 cache.
IMB-C2060 microATX Motherboard
5.3.3 SATA Configuration
Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the
configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA Controller(s) [Enabled]
SATA Mode Selection [IDE]
Serial ATA Port 1 Empty
Serial ATA Port 2 Empty
Serial ATA Port 3 Empty
Serial ATA Port 4 Empty
Serial ATA Port 5 Empty
Serial ATA Port 6 Empty
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enable or disable SATA
Device.
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 6: SATA Configuration
SATA Controller(s) [Enabled]
Use the SATA Controller(s) option to enable or disable the serial ATA controller.
Enabled D
Disabled
Page 78
EFAULT
Disables the on-board SATA controller.
Enables the on-board SATA controller.
Page 93
IMB-C2060 microATX Motherboard
SATA Mode Selection [IDE]
Use the SATA Mode option to configure SATA devices as normal IDE devices.
IDE DEFAULT
AHCI
RAID
Configures SATA devices as normal IDE device.
Configures SATA devices as AHCI device.
Configures SATA devices as RAID device.
5.3.4 Intel TXT(LT) Configuration
Use the Intel TXT(LT) Configuration menu to configure Intel Trusted Execution
Technology support.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel Trusted Execution Technology Configuration
Intel TXT support only can be enabled/disabled if SMX
is enabled. VT and VT-d support must also be enabled prior
to TXT.
Secure Mode Extensons (SMX) Disabled
Intel TXT(LT) Support [Disabled]
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 7: Intel TXT(LT) Configuration
Page 79
Page 94
E
N
IMB-C2060 microATX Motherboard
5.3.5 AMT Configuration
The AMT Configuration menu (BIOS Menu 8) allows Intel® AMT options to be
configured.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel AMT [Enabled]
Un-Configure ME [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
nable/Disable Intel(R)
Active Management
Technology BIOS
Extension.
ote: iAMT H/W is always
enabled.
This option just
controls the BIOS
extension execution. If
enabled, this requires
additional firmware in
the SPI device
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 8: AMT Configuration
Intel AMT [Enabled]
Use Intel AMT option to enable or disable the Intel® AMT function. Please n ote that Intel®
AMT hardware support is always enabled. This option is to control the BIOS extension
execution. If enabled, it requires additional firmware in the SPI device.
Disabled
Enabled DEFAULT
Un-Configure ME [Disabled]
Use the Un-Configure ME option to perform ME unconfigure without password operation.
Page 80
Intel® AMT is disabled
Intel® AMT is enabled
Page 95
d
IMB-C2060 microATX Motherboard
Disabled DEFAULT
Enabled
Disable ME unconfigure
Enable ME unconfigure
5.3.6 USB Configuration
Use the USB Configuration menu (BIOS Menu 9) to read USB configuration information
and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
2 Hubs
Legacy USB Support [Enabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enables Legacy USB
support. AUTO option
isables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 9: USB Configuration
USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
Page 81
Page 96
S
keyboard can control the system even when there is no USB driver loaded onto the
system.
IMB-C2060 microATX Motherboard
Enabled DEFAULT
Disabled
Auto
Legacy USB support enabled
Legacy USB support disabled
Legacy USB support disabled if no USB devices are
connected
5.3.7 F81216 Second Super IO Configuration
The F81216 Second Super IO Configuration (BIOS Menu 10) displays IO chip type and
the submenus for configuring the external serial port 7, 8, 9, and 10.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
F81216 Second Super IO Configuration
Super IO Chip F81216 SecondIo
> Serial Port 7 Configuration
> Serial Port 8 Configuration
> Serial Port 9 Configuration
> Serial Port 10 Configuration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
et Parameters of Serial
Port 7 (COMH)
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 10: F81216 Second Super IO Configuration
5.3.7.1 Serial Port 7 Configuration
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Page 82
Page 97
IMB-C2060 microATX Motherboard
Disabled
Enabled DEFAULT
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Auto DEFAULT
IO=2C0h;
IRQ=11
IO=2C0h;
IRQ=10, 11
IO=2C8h;
IRQ=10, 11
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ11
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2C8h and the interrupt
address is IRQ10, 11
Device Mode [Serial Port Function Mode (RS232)]
Use the Device Mode option to change the serial port mode.
Serial Port Function Mode (RS232) D
IR Mode, Pusle 1.6us, Full Duplex
IR Mode, Pusle 1.6us, Half Duplex
IR Mode, Pusle 3/16 Bit Time, Full Duplex
IR Mode, Pusle 3/16 Bit Time, Half Duplex
5.3.7.2 Serial Port 8 Configuration
Serial Port [Enabled]
EFAULT
Page 83
Page 98
Use the Serial Port option to enable or disable the serial port.
IMB-C2060 microATX Motherboard
Disabled
Enabled DEFAULT
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Auto DEFAULT
IO=2C8h;
IRQ=11
IO=2C0h;
IRQ=10, 11
IO=2C8h;
IRQ=10, 11
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2C8h and the interrupt
address is IRQ11
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2C8h and the interrupt
address is IRQ10, 11
5.3.7.3 Serial Port 9 Configuration
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Disabled
Enabled DEFAULT
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Auto DEFAULT
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Page 84
Page 99
IMB-C2060 microATX Motherboard
IO=2B0h;
IRQ=11
IO=2B0h;
IRQ=10, 11
IO=2B8h;
IRQ=10, 11
Serial Port I/O port address is 2B0h and the interrupt
address is IRQ11
Serial Port I/O port address is 2B0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2B8h and the interrupt
address is IRQ10, 11
5.3.7.4 Serial Port 10 Configuration
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Disabled
Enabled DEFAULT
Change Settings [Auto]
Disable the serial port
Enable the serial port
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Auto DEFAULT
IO=2B8h;
IRQ=11
IO=2B0h;
IRQ=10, 11
IO=2B8h;
IRQ=10, 11
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2B8h and the interrupt
address is IRQ11
Serial Port I/O port address is 2B0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2B8h and the interrupt
address is IRQ10, 11
Page 85
Page 100
S
IMB-C2060 microATX Motherboard
5.3.8 F81866 Super IO Configuration
Use the F81866 Super IO Configuration menu (BIOS Menu 11) to displays IO chip type
and the submenus for configuring the external serial port 1 ~ 6.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Super IO Configuration
Super IO Chip F81866
> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration
> Serial Port 4 Configuration
> Serial Port 5 Configuration
> Serial Port 6 Configuration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
et Parameters of Serial
Port 1 (COMA)
---------------------
: Select Screen
: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 11: F81866 Super IO Configuration
5.3.8.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 12) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Serial Port n Configuration
Serial Port [Enabled]
Device Settings Reset Required
Change Settings [Auto]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enable or Disable Serial
Port (COM)
---------------------
: Select Screen
: Select Item
Enter Select
= - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 12: Serial Port n Configuration Menu
Page 86
Loading...