IEI Technology ICEROCK3-T10-ETC, ICEROCK3-T10-HU, ICEROCK3-T10-HU1, ICEROCK3-T10 User Manual
Page 1
ICEROCK3-T10 Tablet PC
MODEL:
ICEROCK3-T10
Industrial Tablet PC Intel® Core™ i7 CPU,
8 GB DDR3 SDRAM, USB 3.0, Micro HDMI, microSD Slot,
802.11b/g/n Wireless, RFID, Barcode Scanner,
Mobile 3.75G, IP 65, RoHS Compliant
User Manual
Rev. 1.01 – May 20, 2015
Page i
Page 2
Date Version Changes
May 20, 2015 1.01 Added the following sections:
–
Section 3.10: Using 3-in-1 Combo Reader
–
ction 4.10: SCR Driver
Se
–
Section 4.11: MSR Driver
–
Section 4.12: Fingerprint Reader Driver
September 25, 2014 1.00 Initial release
ICEROCK3-T10 Tablet PC
Revision
Page ii
Page 3
ICEROCK3-T10 Tablet PC
COPYRIGHT NOTICE
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
Copyright
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
Page 4
ICEROCK3-T10 Tablet PC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 MODEL VARIATIONS................................................................................................... 3
1.3 FEATURES................................................................................................................... 3
1.4 FRONT PANEL.............................................................................................................4
1.4.1 Status Indicators ................................................................................................ 4
1.5 REAR PANEL............................................................................................................... 6
1.6 SIDE PANELS .............................................................................................................. 6
1.7 TOP PANEL ................................................................................................................. 7
1.8 BOTTOM PANEL .......................................................................................................... 7
1.9 TECHNICAL SPECIFICATIONS ...................................................................................... 8
1.10 DIMENSIONS........................................................................................................... 10
2 UNPACKING................................................................................................................11
2.1 UNPACKING.............................................................................................................. 12
2.2 PACKING LIST........................................................................................................... 13
3 INSTALLATION ......................................................................................................... 15
3.1 CHARGE THE SYSTEM............................................................................................... 16
3.1.1 Optional Charging Station............................................................................... 18
POWER-UP THE SYSTEM ........................................................................................... 19
3.2
3.3
SD CARD INSTALLATION.......................................................................................... 20
3.4 SIM CARD INSTALLATION (OPTIONAL).................................................................... 21
3.5 USING RFID READER............................................................................................... 21
3.6 USING BARCODE SCANNER...................................................................................... 25
3.7 USING GPS EVALUATION SOFTWARE....................................................................... 29
3.8 MOUNTING THE SYSTEM .......................................................................................... 31
3.9 I/O CONNECTORS..................................................................................................... 32
3.9.1 Audio connectors (Mic-in and Headphones)................................................... 32
3.9.2 Micro HDMI Device Connection..................................................................... 33
3.9.3 USB Device Connection................................................................................... 34
Page iv
Page 5
ICEROCK3-T10 Tablet PC
USING 3-IN-1 COMBO READER (OPTIONAL)........................................................... 35
3.10
4 DRIVER INSTALLATION......................................................................................... 38
4.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 39
4.2 INTEL® CHIPSET DRIVER......................................................................................... 39
4.3 INTEL® GRAPHICS DRIVER ...................................................................................... 40
4.4 3.75G DRIVER.......................................................................................................... 42
4.5 AUDIO DRIVER......................................................................................................... 43
4.6 BLUETOOTH DRIVER................................................................................................ 45
4.7 RFID DRIVER .......................................................................................................... 46
4.8 USB 3.0 DRIVER...................................................................................................... 48
4.9
WIRELESS LAN DRIVER .......................................................................................... 49
4.10 SCR DRIVER (OPTIONAL)...................................................................................... 51
4.11 MSR DRIVER (OPTIONAL) ..................................................................................... 54
4.12 FINGERPRINT READER DRIVER (OPTIONAL)........................................................... 58
5 BIOS SETUP................................................................................................................ 60
5.1 INTRODUCTION......................................................................................................... 61
5.1.1 Starting Setup................................................................................................... 61
5.1.2 Using Setup...................................................................................................... 61
5.1.3 Getting Help..................................................................................................... 62
5.1.4 BIOS Menu Bar................................................................................................ 62
5.2 MAIN........................................................................................................................ 63
ADVANCED ............................................................................................................... 64
5.3
5.3.1 ACPI Settings................................................................................................... 65
5.3.2 RTC Wake Settings........................................................................................... 66
5.3.3 T rusted Computing........................................................................................... 68
5.3.4 CPU Configuration.......................................................................................... 69
5.3.5 SATA Configuration ......................................................................................... 71
5.3.6 Intel(R) Rapid Start Technology....................................................................... 72
5.3.7 USB Configuration........................................................................................... 73
5.3.8 iWDD Serial Ports Configuration ................................................................... 74
5.3.8.1 Serial Port n Configuration....................................................................... 75
5.3.9 H/W Monitor.................................................................................................... 77
5.3.10 IEI Feature..................................................................................................... 78
Page v
Page 6
CHIPSET ................................................................................................................... 79
5.4
ICEROCK3-T10 Tablet PC
5.4.1 PCH-IO Configuration .................................................................................... 80
5.4.2 System Agent (SA) Configuration .................................................................... 83
5.4.2.1 Graphics Configuration............................................................................. 84
5.4.2.2 Memory Configuration ............................................................................. 86
5.5 BOOT........................................................................................................................ 86
5.6 SECURITY................................................................................................................. 88
5.7 EXIT......................................................................................................................... 89
6 SYSTEM MAINTENANCE ....................................................................................... 91
6.1 SYSTEM MAINTENANCE INTRODUCTION .................................................................. 92
6.2
MOTHERBOARD REPLACEMENT ............................................................................... 92
6.3 BATTERY REPLACEMENT.......................................................................................... 92
A REGULATORY COMPLIANCE.............................................................................. 94
B SAFETY PRECAUTIONS......................................................................................... 99
B.1 SAFETY PRECAUTIONS........................................................................................... 100
B.1.1 General Safety Precautions........................................................................... 100
B.1.2 Anti-static Precautions.................................................................................. 101
B.1.3 Product Disposal........................................................................................... 102
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ...................................................... 102
B.2.1 Maintenance and Cleaning............................................................................ 102
B.2.2 Cleaning Tools............................................................................................... 103
C BIOS OPTIONS........................................................................................................ 104
D TERMINOLOGY ..................................................................................................... 107
E WATCHDOG TIMER................................................................................................111
F HAZARDOUS MATERIALS DISCLOSURE.........................................................114
HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CER TIFIED AS
F.1
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ......................................115
Page vi
Page 7
ICEROCK3-T10 Tablet PC
List of Figures
Figure 1-1: ICEROCK3-T10 ............................................................................................................2
Figure 1-2: Front Panel ..................................................................................................................4
Figure 1-3: Front Panel LED Indicators........................................................................................4
Figure 1-4: Rear Panel....................................................................................................................6
Figure 1-5: Side Panel....................................................................................................................6
Figure 1-6: Top Panel.....................................................................................................................7
Figure 1-7: Bottom Panel...............................................................................................................7
Figure 1-8: Dimensions (units in mm)........................................................................................10
Figure 3-1: Install Charging Adapter ..........................................................................................16
Figure 3-2: Charge Status LED....................................................................................................17
Figure 3-3: Battery Capacity Indicators .....................................................................................17
Figure 3-4: Windows Embedded 7 Power Management Screen..............................................18
Figure 3-5: Charge the System through Charging Station.......................................................19
Figure 3-6: Power Button Location.............................................................................................19
Figure 3-7: Install microSD Card.................................................................................................20
Figure 3-8: SIM Card Installation.................................................................................................21
Figure 3-9: PcscTool Location....................................................................................................22
Figure 3-10: NXP PCSC Tool Screen..........................................................................................22
Figure 3-11: NXP PCSC Tool – Mode Selection.........................................................................23
Figure 3-12: NXP PCSC Tool – Reader Selection......................................................................23
Figure 3-13: NXP PCSC Tool – Select the Reader.....................................................................23
Figure 3-14: NXP PCSC Tool – Read RFID Card........................................................................24
Figure 3-15: RFID Reader Location.............................................................................................24
Figure 3-16: Barcode Scanner Program Location.....................................................................25
Figure 3-17: EZConfig-Scanning InstallShield Wizard..............................................................26
Figure 3-18: EZConfig-Scanning Window..................................................................................26
Figure 3-19: EZConfig-Scanning – Port Settings......................................................................27
Figure 3-20: Barcode On/Off Button and Barcode Status Indicator........................................28
Figure 3-21: Barcode Information Display Area........................................................................29
Figure 3-22: GPS Evaluation Software Location.......................................................................30
Page vii
Page 8
Figure 3-23: u-center Window.....................................................................................................31
Figure 3-24: VESA Mount Screw Holes......................................................................................31
Figure 3-25: Left Side I/O Connectors........................................................................................32
Figure 3-26: Audio Connectors...................................................................................................33
Figure 3-27: Micro HDMI Device Connection.............................................................................34
Figure 3-28: USB Device Connection.........................................................................................35
Figure 3-29: 3-in-1 Combo Reader..............................................................................................35
Figure 3-30: Combo Reader Installation ....................................................................................36
Figure 3-31: Secure the Combo Reader.....................................................................................36
Figure 4-1: Chipset Driver Location............................................................................................40
Figure 4-2: Graphics Driver Location.........................................................................................41
Figure 4-3: Intel® Graphics Driver InstallShield Wizard...........................................................41
Figure 4-4: 3.75G Driver Location...............................................................................................42
Figure 4-5: 3.75G Driver InstallShield Wizard............................................................................43
ICEROCK3-T10 Tablet PC
Figure 4-6: Speaker and Microphone Driver Location..............................................................44
Figure 4-7: Realtek HD Audio Driver InstallShield Wizard .......................................................44
Figure 4-8: Bluetooth Driver Location........................................................................................45
Figure 4-9: Bluetooth Driver InstallShield Wizard.....................................................................46
Figure 4-10: RFID Driver Folder ..................................................................................................47
Figure 4-11: RFID Driver Installation ..........................................................................................47
Figure 4-12: USB 3.0 Driver Location.........................................................................................48
Figure 4-13: USB 3.0 Driver InstallShield Wizard......................................................................49
Figure 4-14: Wireless LAN Driver Location ...............................................................................50
Figure 4-15: Wireless LAN InstallShield Wizard........................................................................50
Figure 4-16: SCR Driver Folder - usbser.sys.............................................................................51
Figure 4-17: Device Manager - Update Driver Software............................................................51
Figure 4-18: Update Driver Software Window ...........................................................................52
Figure 4-19: Browse for Driver Software Window.....................................................................52
Figure 4-20: Installing Driver Window........................................................................................53
Figure 4-21: Driver Installation Complete Window ...................................................................53
Figure 4-22: Device Manager Window........................................................................................54
Figure 4-23: MSR Driver Folder - usbser.sys.............................................................................54
Figure 4-24: Device Manager - Update Driver Software............................................................55
Figure 4-25: Update Driver Software Window ...........................................................................55
Figure 4-26: Browse for Driver Software Window.....................................................................56
Page viii
Page 9
ICEROCK3-T10 Tablet PC
Figure 4-27: Installing Driver Window........................................................................................56
Figure 4-28: Driver Installation Complete Window ...................................................................57
Figure 4-29: Device Manager Window........................................................................................57
Figure 4-30: Fingerprint Reader Driver Folder ..........................................................................58
Figure 4-31: Fingerprint Reader Driver InstallShield Wizard ...................................................59
Figure 6-1: Unlock Battery Latches............................................................................................92
Figure 6-2: Battery Installation....................................................................................................93
Page ix
Page 10
ICEROCK3-T10 Tablet PC
List of Tables
Table 1-1: Model Variations...........................................................................................................3
Table 1-2: Status Indicators...........................................................................................................5
Table 1-3: Technical Specifications..............................................................................................9
Table 2-1: Packing List.................................................................................................................13
Table 2-2: Optional Items.............................................................................................................14
Table 5-1: BIOS Navigation Keys................................................................................................62
Page x
Page 11
ICEROCK3-T10 Tablet PC
BIOS Menus
BIOS Menu 1: Main.......................................................................................................................63
BIOS Menu 2: Advanced..............................................................................................................65
BIOS Menu 3: ACPI Configuration..............................................................................................65
BIOS Menu 4: RTC Wake Settings..............................................................................................66
BIOS Menu 5: Trusted Computing..............................................................................................68
BIOS Menu 6: CPU Configuration...............................................................................................69
BIOS Menu 7: SATA Configuration.............................................................................................71
BIOS Menu 8: Intel(R) Rapid Start Technology .........................................................................72
BIOS Menu 9: USB Configuration...............................................................................................73
BIOS Menu 10: iWDD Super IO Configuration...........................................................................74
BIOS Menu 11: Serial Port 1 Configuration Menu.....................................................................75
BIOS Menu 12: Hardware Health Configuration........................................................................77
BIOS Menu 13: IEI Feature...........................................................................................................78
BIOS Menu 14: Chipset................................................................................................................79
BIOS Menu 15: Host Bridge Chipset Configuration..................................................................80
BIOS Menu 16: System Agent (SA) Configuration....................................................................83
BIOS Menu 17: Graphics Configuration.....................................................................................84
BIOS Menu 18: Memory Configuration.......................................................................................86
BIOS Menu 19: Boot.....................................................................................................................86
BIOS Menu 20: Security...............................................................................................................88
BIOS Menu 21:Exit........................................................................................................................89
Page xi
Page 12
Page 13
ICEROCK3-T10 Tablet PC
Chapter
1
1 Introduction
Page 1
Page 14
1.1 Overview
ICEROCK3-T10 Tablet PC
Figure 1-1: ICEROCK3-T10
The ICEROCK3-T10 is an industrial tablet PC with a 10.1 inch touchscreen and an IP 65
rating protection. The ICEROCK3-T10 features an Intel® Celeron® 1007U or Intel®
Core™ i7-3517 processor with DDR3 SDRAM on-board.
Storage needs are met by the preinstalled 32 GB MLC mSATA module, and by installing a
microSD card into the slot on the side panel.
Wireless networking is enabled through an 802.11b/g/n wireless adapter. A Bluetooth 3.0
module provides a connection to Bluetooth devices. An optional mobile 3.75G module
provides a connection to mobile phone networks. There are three USB 3.0 ports and one
Micro HDMI port for peripherals.
A 1.3 megapixel webcam and microphone provide video conferencing capabilities.
Audio connections include one line-out for connecting to headphones and an input for an
external microphone. One 2 watt speaker is built-in.
Page 2
Some ICEROCK3-T10 models also feature a barcode scanner and a RFID reader for
advanced data acquisition.
Page 15
ICEROCK3-T10 Tablet PC
1.2 Model Variations
The ICEROCK3-T10 series has three models. All of the models are equipped with a
projected capacitive touchscreen, IPS, 802.11b/g/n Wi-Fi and Bluetooth v3.0. The model
variations are listed below.
Models Intel
ICEROCK3-T10-ETC Celeron®
ICEROCK3-T10-HU Celeron®
ICEROCK3-T10-HUI Core
Table 1-1: Model Variations
1.3 Features
Some of the standard features of the ICEROCK3-T10 tablet PC include:
1.70 GHz Intel® Core™ i7-3517U processor or 1.50 GHz Intel® Celeron®
4.0 GB DDR3 SDRAM on board and optional 4.0 GB DDR3 SDRAM
Memory 3.75G GPS RFID Barcode Rear
CPU
4 GB No No Yes No No No
1007U
8 GB Yes Yes Yes Yes Yes Yes
1007U
i7-3517U
8 GB Yes Yes Yes Yes Yes Yes
processor 1007U platform
Camera
2nd
Battery
SO-DIMM
Projected capacitive type touchscreen supported
Built-in 1.3-megapixel webcam (front panel) and optional 5-megapixel
webcam (rear panel)
Built-in one 2 W speaker and digital microphone
802.11b/g/n wireless LAN
Bluetooth v3.0
One Micro HDMI and three USB 3.0 ports
One Key Recovery
IP 65 rating protection
RoHS compliant
Page 3
Page 16
1.4 Front Panel
The front panel of the ICEROCK3-T10 has a 10.1” TFT LCD with a multi-touch projected
capacitive touchscreen. Four LED indicators are also located on the front panel.
ICEROCK3-T10 Tablet PC
Figure 1-2: Front Panel
1.4.1 Status Indicators
Figure 1-3: Front Panel LED Indicators
There are four LED indicators on the front panel of the ICEROCK3-T10 as show in the
figure above. The following table contains descriptions of their functions.
Page 4
Page 17
ICEROCK3-T10 Tablet PC
Status Indicator Description
Battery
Barcode/RFID
Storage/3.75G
Bluetooth/Wi-Fi
Off: the system is fully charged or not being charged
Solid red: Battery 1 is being charged.
Solid blue: Battery 2 is being charged.
Blinking red: Battery 1 is low
Blinking blue: Battery 2 is low
Off: the barcode scanner or the RFID reader is off
Solid red: the barcode scanner is turned on
Solid blue: the RFID reader is enabled
Solid purple: the barcode scanner and the RFID reader are both
enabled
Off: the system is off or suspends
Blinking red: the storage device is being accessed
Blinking blue: 3.75G connection is being accessed
Off: Bluetooth or Wi-Fi is not active
Blinking red: Wi-Fi RF is active
Blinking blue: Bluetooth is active
Blinking purple: Bluetooth and Wi-Fi are both active
Table 1-2: Status Indicators
Page 5
Page 18
1.5 Rear Panel
The rear panel consists of the built-in battery and VESA mounting holes. The optional
5-megapixel camera is also located on the rear panel.
ICEROCK3-T10 Tablet PC
Figure 1-4: Rear Panel
1.6 Side Panels
The right side panel has a barcode on/off button. The left side panel consists of I/O ports
and slots. See Figure 1-5.
Page 6
Figure 1-5: Side Panel
Page 19
ICEROCK3-T10 Tablet PC
1.7 Top Panel
The barcode scanner is located on the top panel shown in the following diagram.
Figure 1-6: Top Panel
1.8 Bottom Panel
The bottom panel has a USB 3.0 connector for installing USB peripheral devices or the
charging adapter.
Figure 1-7: Bottom Panel
Page 7
Page 20
ICEROCK3-T10 Tablet PC
1.9 Technical Specifications
The technical specifications for the ICEROCK3-T10 systems are listed in the table below.
System ICEROCK3-T10
CPU 1.700 GHz Intel® Core i7-3517U processor
1.50 GHz Intel® Celeron® processor 1007U
Chipset Intel® HM76
Memory 4.0 GB DDR3 SDRAM on board
Optional 4.0 GB DDR3 SDRAM SO-DIMM
OS Windows Embedded Standard 7
Storage Preinstalled 32 GB MLC mSATA
One microSD card slot
Audio 1 x Speaker (2 W)
1 x Digital microphone on the front panel
1 x Analog microphone connector on the side panel
Camera 1 x 1.3-megapixel webcam (front panel)
1 x Optional 5-megapixel webcam (rear panel)
Display
LCD 10.1” LCD with projected capacitive touchscreen and Gorilla Glass
Max. Resolution 1280 x 800
Brightness (cd/m2) 350
Viewing Angle 85/85/85/85 degree
Communication
Wireless LAN 802.11b/g/n
Bluetooth Bluetooth v3.0
Barcode Scanner
(Optional)
RFID Reader (Optional) 13.56 MHz RFID compliant with ISO 14443A/B (Mifare, Felica)
GPS (Optional) GPS with internal antenna
1D/2D barcode scanner
3.75G (Optional) HSPA/UMTS-800/850/900/1700/1900/2100 MHz
Page 8
Page 21
ICEROCK3-T10 Tablet PC
System ICEROCK3-T10
Power
Battery Battery 1 (standard): 3700 mAH Li-ion battery pack with battery capacity
LED indicators (five working hours)
Battery 2 (optional): internal 3700 mAH battery pack (five working hours)
Power Input 19 V DC input
Power Adapter 90 W AC Power Adapter
Input: 100 V AC ~ 240 V AC
Output: 19 V DC @ 4.74 A
Physical Character
Mounting VESA 75 mm x 75 mm
Dimensions (W x H x D) 297 mm x 234 mm x 32 mm
Operation Temperature 0ºC ~ 40ºC
Storage Temperature -20ºC ~ 60ºC
Humidity 5% ~ 95% non-condensing
Net Weight 1.9 kg
IP Level IP 65
Safety CE, FCC
Drop Survival 1.2 m
Connectors and Buttons
I/O Ports and Switches 3 x USB 3.0
1 x Microphone line-in jack
1 x Audio line-out jack
1 x Micro HDMI
1 x Barcode on/off button
Front Panel Buttons and
LED Indicators
1 x Power button
2 x Hotkey
1 x iMenu button
1 x Battery status LED
1 x Barcode/RFID LED
1 x Storage/3.75G LED
1 x Wi-Fi/Bluetooth LED
Table 1-3: Technical Specifications
Page 9
Page 22
1.10 Dimensions
ICEROCK3-T10 Tablet PC
Figure 1-8: Dimensions (units in mm)
Page 10
Page 23
ICEROCK3-T10 Tablet PC
Chapter
2
2 Unpacking
Page 11
Page 24
ICEROCK3-T10 Tablet PC
WARNING:
When installing the ICEROCK3-T10, make sure to:
Turn the power off: Chance of electrocution. Turn off the monitor
and unplug it from the power supply.
Only let certified engineers change the hardware settings:
Incorrect settings can cause irreparable damage to the product.
Take anti-static precautions: Electrostatic discharge can destroy
electrical components and injure the user. Users must ground
themselves using an anti-static wristband or similar device.
The installation steps below should be followed in order.
Step 1: Unpack the tablet PC
Step 2: Check all the required parts are included
Step 3: Charge the system
Step 4: Install SIM card or microSD card (if necessary)
Step 5: Mount the tablet PC
Step 6: Connect peripheral devices to the side panel of the ICEROCK3-T10 Step 0:
2.1 Unpacking
To unpack the ICEROCK3-T10, follow the steps below:
WARNING!
Only remove the protective plastic cover stuck to the front screen after
Page 12
installation. The plastic layer protects the monitor surface during
installation process.
Step 1: Use sharp cutters to open the box.
Page 25
ICEROCK3-T10 Tablet PC
Step 2: Remove the ICEROCK3-T10 and the packing material out of the box.
Step 3: Make sure all the components listed in the packing list are present. Step 0:
2.2 Packing List
The ICEROCK3-T10 tablet PC is shipped with the following components:
Quantity Item Image
1 ICEROCK3-T10
1 Power adapter
1 Power cable
1 Charging adapter
1 Utility CD
1 One Key Recovery CD
Table 2-1: Packing List
Page 13
Page 26
These optional items are also available.
Item Image
3-in-1 combo reader
(P/N: ICEROCK3-3IN1-R10)
Charging station
(P/N: ICEROCK3-CR01-R10)
Carrying case
(P/N: 7Z000-ICEROCK3-10POUCH)
ICEROCK3-T10 Tablet PC
Table 2-2: Optional Items
Page 14
Page 27
ICEROCK3-T10 Tablet PC
Chapter
3
3 Installation
Page 15
Page 28
3.1 Charge the System
WARNING:
When charging the system, make sure a power supply with the correct
input voltage is being fed into the system. Incorrect voltages applied to
the system may cause damage to the internal electronic components
and may also cause injury to the user.
To charge the ICEROCK3-T10, follow the steps below.
Step 1: Install the charging adapter to the ICEROCK3-T10. Secure the charging adapter
by tightening the two retention screws on either side of the adapter.
ICEROCK3-T10 Tablet PC
Page 16
Figure 3-1: Install Charging Adapter
Step 2: Connect the ICEROCK3-T10 with a power source through the power adapter
came with the package.
Step 3: The system starts to charge the battery and the charge status LED lights up
indicating the battery is being charged. When the battery is fully charged, the
power status LED turns off. Please refer to Section 1.4.1: Status Indicators.
Page 29
ICEROCK3-T10 Tablet PC
Figure 3-2: Charge Status LED
Step 4: The battery 1 capacity can be viewed by pressing the button on the battery pack
(Figure 3-3).
Figure 3-3: Battery Capacity Indicators
Step 5: The user can also turn on the system to check the battery capacity via the
Windows Embedded 7 power management screen (
74Figure 3-4).
Page 17
Page 30
Figure 3-4: Windows Embedded 7 Power Management Screen
ICEROCK3-T10 Tablet PC
NOTE:
The external battery is hot swappable which means the user can install
the battery without turning off the system.
3.1.1 Optional Charging Station
The ICEROCK3-T10 can be charged through the optional charging station. To charge the
system, install the ICEROCK3-T10 into the charging station as shown in Figure 3-5. Th
connect the charging station with a power source through the power adapter came with
the ICEROCK3-T10 package.
en,
Page 18
Page 31
ICEROCK3-T10 Tablet PC
Figure 3-5: Charge the System through Charging Station
3.2 Power-up the System
To power-up the system, push the power button on the top panel for few seconds until the
power button lights up.
Figure 3-6: Power Button Location
Page 19
Page 32
3.3 SD Card Installation
This section covers the installation of a microSD card.
Step 1: Open the I/O cover on the side panel. Locate the microSD card slot.
Step 2: Install the microSD card in the slot indicated below.
ICEROCK3-T10 Tablet PC
Figure 3-7: Install microSD Card
Step 3: Replace the I/O cover.Step 0:
Page 20
Page 33
ICEROCK3-T10 Tablet PC
3.4 SIM Card Installation (Optional)
This section covers the installation of a SIM card for mobile network connections on the
ICEROCK3-T10 models with optional mobile 3.75G module.
Step 1: Open the I/O cover on the side panel. Locate the SIM card slot.
Step 2: Install the SIM card in the slot indicated below.
Figure 3-8: SIM Card Installation
Step 3: Replace the I/O cover.Step 0:
3.5 Using RFID Reader
There is a RFID reader on the front panel. To use the RFID reader, follow the steps below.
Step 1: Check the RFID status indicator on the front panel to make sure the RFID
function is enabled (see Section 1.4.1).
in the BIOS menu. If the RFID reader is disabled, please go to Chipset
PCH-IO Configuration BIOS menu to enable it (refer to Section 5.4.1).
Step 2: Follow the in
Step 3: Double click the PcscTool icon in the RFID folder in the driver CD.
struction described in Section 4.7 to ins
The RFID function is enabled by default
tall the RFID driver.
Page 21
Page 34
ICEROCK3-T10 Tablet PC
Figure 3-9: PcscTool Location
Step 4: The NXP PCSC Tool window appears (
4Figure 3-10).
Page 22
Figure 3-10: NXP PCSC Tool Screen
Step 5: Select Automatic from the Mode menu (
4Figure 3-11).
Page 35
ICEROCK3-T10 Tablet PC
Figure 3-11: NXP PCSC Tool – Mode Selection
Step 6: Choose Select a Reader from the Reader menu (
4Figure 3-12).
Figure 3-12: NXP PCSC Tool – Reader Selection
Step 7: The Select the reader window prompts. Select a RFID reader and click OK. See
Figure 3-13.
Figure 3-13: NXP PCSC Tool – Select the Reader
Page 23
Page 36
Step 8: Click the Arrow button shown in Figure 3-14 to read RFID card.
Figure 3-14: NXP PCSC Tool – Read RFID Card
Step 9: Use the RFID reader to read a RFID card. The RFID reader is located on the
ICEROCK3-T10 Tablet PC
front panel as shown in Figure 3-15.
Scenario and Logs columns of the PCSC Tool.
Figure 3-15: RFID Reader Location
The card information will be shown in the
Page 24
Page 37
ICEROCK3-T10 Tablet PC
3.6 Using Barcode Scanner
Some models of the ICEROCK3-T10 have a barcode scanner on the top panel. To use
the barcode scanner, follow the steps below.
Step 1: Check the barcode status indicator on the front panel to make sure the barcode
function is enabled (see Section 1.4.1).
default in the BIOS menu. If the barcode scanner is disabled, please go to
Chipset PCH-IO Configuration BIOS menu to enable it (refer to Section
5.4.1).
Step 2: Inst
click “EZConfig-Scanning-Setup.exe” file in the “2D” folder as shown in
574Figure 3-16.
The barcode function is enabled by
all EZConfig-Scanning barcode scanner program from the driver CD. Double
Figure 3-16: Barcode Scanner Program Location
Step 3: The EZConfig-Scanning InstallShield Wizard screen appears (Figure 3-17).
Follow the
EZConfig-Scanning barcode scanner program.
step-by-step instruction of the installation wizard to install the
Page 25
Page 38
ICEROCK3-T10 Tablet PC
Figure 3-17: EZConfig-Scanning InstallShield Wizard
Step 4: Double click the EZConfig-Scanning icon on the desktop. The
EZConfig-Scanning window appears (
4Figure 3-18).
Page 26
Figure 3-18: EZConfig-Scanning Window
Page 39
ICEROCK3-T10 Tablet PC
Step 5: Click the Port Settings button on the tool bar. Refer the following information to
configure the COM port settings for the barcode scanner. After the configuration,
click the Config Comm button (
Port Number: COM2
Baud Rate: 115200
Parity Bits: None
Date Bits: 8
Stop Bits: 1
Hand Shaking: 0-None
4Figure 3-19).
Figure 3-19: EZConfig-Scanning – Port Settings
Step 6: The Config Comm button turns from red to green, meaning the program is
successfully connected to the barcode scanner.
Page 27
Page 40
Step 7: Push the barcode on/off button on the right side panel to turn on the barcode
scanner. The barcode status indicator on the front panel lights up in red (if the
RFID reader is enabled at the same time, the indicator will turns from blue to
purple).
ICEROCK3-T10 Tablet PC
Figure 3-20: Barcode On/Off Button and Barcode Status Indicator
Step 8: Scan a barcode and the barcode number will be displayed in the Scan Data
Window on the right (
4Figure 3-21).
NOTE:
The Scan Data Window must be enabled to be able to display the
scanned barcode number. To enable, click View Scan Data
Window.
Page 28
Page 41
ICEROCK3-T10 Tablet PC
Figure 3-21: Barcode Information Display Area
3.7 Using GPS Evaluation Software
To evaluate the GPS function on the ICEROCK3-T10 models with GPS module, please
follow the instruction below.
Step 1: The GPS function is enabled by default in the BIOS menu. If the GPS function is
disabled, please go to Chipset PCH-IO Configuration BIOS menu to enable
it (refer to Section 5.4.1).
Step 2: Inst
all the u-center GPS evaluation software from the driver CD. Double click the
u-center setup file in the “GPS Module” folder as shown in Figure 3-22.
NOTE:
The u-center software installation requires network connection. Please
connect the ICEROCK3-T10 to the Internet before installation.
Page 29
Page 42
ICEROCK3-T10 Tablet PC
Figure 3-22: GPS Evaluation Software Location
Step 3: The InstallShield Wizard screen appears. Follow the step-by-step instruction of
the installation wizard to install the u-center GPS evaluation software.
Step 4: After the installation is complete, double click the u-center icon on the desktop.
The u-center window appears (
please make sure the GPS module is connected successfully by checking the
information on the bottom (circled in red in Figure 3-23).
COM1 port with 9600 baud rate, and the blinking green light shows the
connection is good.
4Figure 3-23). Before start using the software,
The GPS module uses
Page 30
Page 43
ICEROCK3-T10 Tablet PC
Figure 3-23: u-center Window
3.8 Mounting the System
The ICEROCK3-T10 is VESA (Video Electronics Standards Association) compliant and
can be mounted on a mounting device with a 75 mm interface pad. The VESA mounting
screw holes are located on the rear panel as shown in the following diagram. To mount the
ICEROCK3-T10, please refer to the user manual that came with the mounting device.
Figure 3-24: VESA Mount Screw Holes
Page 31
Page 44
3.9 I/O Connectors
The I/O connectors on the left side of the ICEROCK3-T10 extend the capabilities of the
tablet PC but are not essential for operation (Figure 3-25).
ICEROCK3-T10 Tablet PC
Figure 3-25: Left Side I/O Connectors
3.9.1 Audio connectors (Mic-in and Headphones)
The audio jacks on the external audio connector enable the ICEROCK3-T10 to be
connected to a stereo sound setup. To install the audio devices, follow the steps below.
Step 1: Identify the audio plugs. The plugs on your headphone or speakers may not
match the colors on the side panel audio jacks. If audio plugs are plugged into
the wrong jacks, sound quality will be very bad.
Step 2: Plug the audio plugs into the audio jacks. Plug the audio plugs into the audio
jacks. If the plugs on your speakers are different, an adapter will need to be used
to plug them into the audio jacks.
Line Out port (Lime): Connects to a headphone or a speaker.
Microphone (Pink): Connects to a microphone.
Page 32
Page 45
ICEROCK3-T10 Tablet PC
Figure 3-26: Audio Connectors
Step 3: Check audio clarity. Check that the sound is coming through the right speakers
by adjusting the balance front to rear and left to right. Step 0:
3.9.2 Micro HDMI Device Connection
There is one Micro HDMI connector on the left side of the ICEROCK3-T10. To connect a
HDMI device, please follow the instructions below.
Step 1: Located the Micro HDMI connector. The location of the Micro HDMI connector
is shown in Figure 3-25.
Step 2: Align the co
the ICEROCK3-T10. See figure below.
nnectors. Align the HDMI device connector with the connector on
Page 33
Page 46
Figure 3-27: Micro HDMI Device Connection
Step 3: Insert the device connector. Once aligned, gently insert the HDMI device
ICEROCK3-T10 Tablet PC
connector into the connector on the ICEROCK3-T10. Step 0:
3.9.3 USB Device Connection
There are two USB 3.0 connectors on the side panel. To connect a USB device, please
follow the instructions below.
Step 1: Located the USB connectors. The locations of the USB connectors are shown
in Figure 3-25.
Step 2: Align the co
connectors on the ICEROCK3-T10. See figure below.
nnectors. Align the USB device connector with one of the
Page 34
Page 47
ICEROCK3-T10 Tablet PC
Figure 3-28: USB Device Connection
Step 3: Insert the device connector. Once aligned, gently insert the USB device
connector into the connector on the ICEROCK3-T10. Step 0:
3.10 Using 3-in-1 Combo Reader (Optional)
The 3-in-1 combo reader is an optional item for the ICEROCK3-T10. The combo reader
combines fingerprint reader, smart card reader (SCR) and magnetic stripe reader (MSR)
into one compact device.
Figure 3-29: 3-in-1 Combo Reader
Page 35
Page 48
To install the combo reader to the ICEROCK3-T10, please follow the steps below.
Step 1: Align the USB connectors on the reader with the two USB 3.0 connectors on the
left side panel of the ICEROCK3-T10.
Step 2: Insert and connect the USB connectors to install the combo reader.
See Figure 3-30.
ICEROCK3-T10 Tablet PC
Figure 3-30: Combo Reader Installation
Step 3: Secure the combo reader to the system by inserting two retention screws into
the rear panel of the ICEROCK3-T10 and tightening them.
Figure 3-31: Secure the Combo Reader
Page 36
Page 49
ICEROCK3-T10 Tablet PC
Step 4: Install the drivers for these three reader by following the instructions described in
Chapter 4:
Section 4.10: SCR Driver
Section 4.11: MSR Driver
Section 4.12: Fingerprint Reader Driver
Page 37
Page 50
ICEROCK3-T10 Tablet PC
Chapter
4
4 Driver Installation
Page 38
Page 51
ICEROCK3-T10 Tablet PC
4.1 Available Software Drivers
NOTE:
The contents of the driver folder may vary throughout the life cycle of
the product and is subject to change without prior notice. Visit the IEI
website or contact technical support for the latest updates.
The following drivers can be installed on the system:
Chipset driver
Graphics driver
3.75G driver
Audio driver
Bluetooth driver
RFID driver
USB 3.0 driver
Wireless LAN driver
Connect the Utility CD came with the ICEROCK3-T10 to the system and follow the
installation instructions given below to install the drivers.
NOTE:
The chipset driver must be installed first, then the graphics driver. After
finishing installing the chipset driver and graphics driver, the user can
continue to install other drivers in any order.
4.2 Intel® Chipset Driver
To install the chipset driver, please follow the steps below.
Step 1: Select BIOS from the list of the driver CD and the following screen shows.
Page 39
Page 52
ICEROCK3-T10 Tablet PC
Figure 4-1: Chipset Driver Location
Step 2: There are three folders, and each folder contains chipset related drivers to be
installed. Double click the setup file in each folder and follow the step-by-step
instruction of the installation wizard to install the drivers.
4.3 Intel® Graphics Driver
To install the graphics driver, please follow the steps below.
Step 1: Select VGA from the list of the driver CD. Locate the driver setup file as shown
474Figure 4-2.
in
Page 40
Page 53
ICEROCK3-T10 Tablet PC
Figure 4-2: Graphics Driver Location
Step 2: Double click the setup file in the folder. The Intel® Graphics Driver
InstallShield Wizard appears (
474Figure 4-3).
Figure 4-3: Intel® Graphics Driver InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the
graphics driver.
Page 41
Page 54
4.4 3.75G Driver
To install the driver for the 3.75G module, please follow the steps below.
Step 1: Select GOBI 3000 from the list of the driver CD. Locate the driver setup file in
ICEROCK3-T10 Tablet PC
the Drivers folder as shown in
Figure 4-4: 3.75G Driver Location
474Figure 4-6.
Page 42
Step 2: Double click the setup file in the folder. The InstallShield Wizard screen
appears (
4Figure 4-7).
Page 55
ICEROCK3-T10 Tablet PC
Figure 4-5: 3.75G Driver InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the HD
Audio driver.
4.5 Audio Driver
To install the driver for the speaker and the microphone, please follow the steps below.
Step 1: Select Audio from the list of the driver CD. Locate the driver setup file as shown
474Figure 4-6.
in
Page 43
Page 56
ICEROCK3-T10 Tablet PC
Figure 4-6: Speaker and Microphone Driver Location
Step 2: Double click the setup file in the folder. The InstallShield Wizard screen
appears (
4Figure 4-7).
Figure 4-7: Realtek HD Audio Driver InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the HD
Audio driver.
Page 44
Page 57
ICEROCK3-T10 Tablet PC
4.6 Bluetooth Driver
To install the Bluetooth driver, please follow the steps below.
Step 1: Select Wireless LAN & Bluetooth from the list of the driver CD. Select the
Bluetooth folder as shown in
Figure 4-8: Bluetooth Driver Location
4Figure 4-8.
Step 2: Double click the setup file in the folder. The InstallShield Wizard screen appears.
Page 45
Page 58
Figure 4-9: Bluetooth Driver InstallShield Wizard
ICEROCK3-T10 Tablet PC
Step 3: Follow the step-by-step instruction of the installation wizard to install the
Bluetooth driver.
4.7 RFID Driver
To install the RFID driver, please follow the steps below.
Step 1: Select RFID from the list of the driver CD. Double click the setup file in the WIN7
Driver folder to install the RFID driver (
474Figure 4-11).
Page 46
Page 59
ICEROCK3-T10 Tablet PC
Figure 4-10: RFID Driver Folder
Step 2: Follow the step-by-step instruction of the installation wizard (Figure 4-11) to
inst
all the RFID driver.
Figure 4-11: RFID Driver Installation
Page 47
Page 60
4.8 USB 3.0 Driver
To install the USB 3.0 driver, please follow the steps below.
NOTE:
Two USB 3.0 drivers must be installed in order to enable all three
USB 3.0 ports on the ICEROCK3-T10. One is included in the Chipset
driver folder (see Section 4.2), and the other is in the USB 3.0 driver
ICEROCK3-T10 Tablet PC
folder. Plea
se follow the instructions in these two sections to install the
USB 3.0 drivers.
Step 1: Select USB 3.0 from the list of the driver CD. Locate the driver setup file as
shown in
474Figure 4-2.
Page 48
Figure 4-12: USB 3.0 Driver Location
Step 2: Double click the setup file in the folder. The InstallShield Wizard appears
(
474Figure 4-3).
Page 61
ICEROCK3-T10 Tablet PC
Figure 4-13: USB 3.0 Driver InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the
graphics driver.
4.9 Wireless LAN Driver
To install the wireless LAN driver, please follow the steps below.
Step 1: Select Wireless LAN & Bluetooth from the list of the driver CD. Select the
Wireless folder as shown in
574Figure 4-14.
Page 49
Page 62
ICEROCK3-T10 Tablet PC
Figure 4-14: Wireless LAN Driver Location
Step 2: Double click the setup file in the Install_CD folder. The InstallShield Wizard
screen appears (Figure 4-15).
Page 50
Figure 4-15: Wireless LAN InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the
Wireless LAN driver.
Page 63
ICEROCK3-T10 Tablet PC
4.10 SCR Driver (Optional)
Follow the steps below to install the SCR driver.
Step 1: Open the SCR driver folder and locate the usbser.sys file at
SCR\DRIVER\Windows Driver (Singular). See Figure 4-16. Copy the
bser.sys file to C:\WINDOWS\system32\drivers directory.
us
Figure 4-16: SCR Driver Folder - usbser.sys
Step 2: Open the Device Manager window. Long press or right click Singular VCOM
Card Reader. Select Update Driver Software from the pop-up window.
Figure 4-17: Device Manager - Update Driver Software
Page 51
Page 64
Step 3: The Update Driver Sof t ware window appears. Select Browse my computer
for driver software.
ICEROCK3-T10 Tablet PC
Figure 4-18: Update Driver Software Window
Step 4: The following window appears. Press/Click the Browse button to specify the
SCR driver directory (SCR\DRIVER\Windows Driver (Singular)). Then,
press/click the Next button.
Page 52
Figure 4-19: Browse for Driver Software Window
Page 65
ICEROCK3-T10 Tablet PC
Step 5: The following window (Figure 4-20) appears as the driver is installed.
Figure 4-20: Installing Driver Window
Step 6: After the driver installation process is complete, a confirmation screen appears.
Click Close to exit the program.
Figure 4-21: Driver Installation Complete Window
Page 53
Page 66
Step 7: The Device Manager Window now shows the installed SCR driver.
ICEROCK3-T10 Tablet PC
Figure 4-22: Device Manager Window
4.11 MSR Driver (Optional)
Follow the steps below to install the MSR driver.
Step 1: Open the MSR driver folder and locate the usbser .sys file at MSR\Windows
Driver (Singular). See Figure 4-23. Copy the us
C:\WINDOWS\system32\drivers directory.
bser.sys file to
Page 54
Figure 4-23: MSR Driver Folder - usbser.sys
Page 67
ICEROCK3-T10 Tablet PC
Step 2: Open the Device Manager window. Long press or right click Singular VCOM
Card Reader. Select Update Driver Software from the pop-up window.
Figure 4-24: Device Manager - Update Driver Software
Step 3: The Update Driver Sof t ware window appears. Select Browse my computer
for driver software.
Figure 4-25: Update Driver Software Window
Page 55
Page 68
Step 4: The following window appears. Press/Click the Browse button to specify the
MSR driver directory (MSR\Windows Driver (Singular)). Then, press/click the
Next button.
ICEROCK3-T10 Tablet PC
Figure 4-26: Browse for Driver Software Window
Step 5: The following window (Figure 4-27) a
ppears as the driver is installed.
Page 56
Figure 4-27: Installing Driver Window
Page 69
ICEROCK3-T10 Tablet PC
Step 6: After the driver installation process is complete, a confirmation screen appears.
Click Close to exit the program.
Figure 4-28: Driver Installation Complete Window
Step 7: The Device Manager Window now shows the installed MSR driver.
Figure 4-29: Device Manager Window
Page 57
Page 70
4.12 Fingerprint Reader Driver (Optional)
Follow the steps below to install the fingerprint reader driver.
Step 1: The fingerprint reader driver is located in the folder shown in Figure 4-30.
ble click the setup.exe file in this folder to install the driver.
Dou
ICEROCK3-T10 Tablet PC
Page 58
Figure 4-30: Fingerprint Reader Driver Folder
Step 2: The Egis ES603 WDM Driver welcome window appears.
Page 71
ICEROCK3-T10 Tablet PC
Figure 4-31: Fingerprint Reader Driver InstallShield Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the
fingerprint reader driver.
Page 59
Page 72
ICEROCK3-T10 Tablet PC
Chapter
5
5 BIOS Setup
Page 60
Page 73
ICEROCK3-T10 Tablet PC
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the E
2. Press the E
appears on the screen. 0.
If the message disappears before the E
again.
NTER key as soon as the system is turned on or
NTER key when the “Press Enter to enter SETUP” message
NTER key is pressed, restart the computer and try
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press E
keys are shown in Table 5-1.
Key Function
Up arrow Move to the item above
Down arrow Move to the item below
Left arrow Move to the item on the left hand side
SC to quit. Navigation
Right arrow Move to the item on the right hand side
+ Increase the numeric value or make changes
Page 61
Page 74
Key Function
- Decrease the numeric value or make changes
Page up Move to the next page
Page down Move to the previous page
Esc Main Menu – Quit and do not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu --
Exit current page and return to Main Menu
F1 key General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key Load previous values
F3 key Load optimized defaults
F4 key Save changes and Exit BIOS
ICEROCK3-T10 Tablet PC
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press E
the F1 key again.
5.1.4 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main – Changes the basic system configuration.
Advanced – Changes the advanced system settings.
Chipset – Changes the chipset settings.
Boot – Changes the system boot configuration.
Security – Sets User and Supervisor Passwords.
Save & Exit – Selects exit options and loads default settings
SC or
Page 62
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 75
S
ICEROCK3-T10 Tablet PC
5.2 Main
The Main BIOS menu (584BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.3
Compliency UEFI 2.3; PI 1.2
Project Version Z255AR01.ROM
Build Date and Time 06/16/2014 17:29:48
iWDD Vendor iEi
iWDD Version B252ET10.bin
Processor Information
Name IvyBridge
Brand String Intel(R) Core(TM) i7-351
Frequency 1600 MHz
Processor ID 306a9
Stepping E1
Number of Processors 2Core(s) / 4Thred(s)
Microcode Revision 13
GT Info GT2 (1000 MHz)
IGFX VBIOS Version 2143
Memory RC Version 1.7.0.0
Total Memory 8192 MB (DDR3)
Memory Frequency 1333 Mhz
PCH Information
Name PantherPoint
Stepping 04/C1
LAN PHY Revision N/A
ME FW Version 8.1.2.1318
ME Firmware SKU 1.5MB
SPI Clock Frequency
DDFR Support Unsupported
Read Status Clock Frequency 33 MHz
Write Status Clock Frequency 33 MHz
Fast Read Status Clock Frequency33 MHz
System Date [Tue 07/04/2011]
System Time [14:20:27]
Access Level Administrator
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
et the Time. Use Tab to
switch between Time
elements.
----------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
BIOS Menu 1: Main
Page 63
Page 76
The Main menu has two user configurable fields:
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (584BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
ICEROCK3-T10 Tablet PC
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Page 64
Page 77
S
w
ICEROCK3-T10 Tablet PC
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> ACPI Settings
> RTC Wake Settings
> Trusted Computing
> CPU Configuration
> SATA Configuration
> Intel Rapid Start Technology
> USB Configuration
> iWDD Serial Ports Configuration
> H/M Monitor
> iEi Feature
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 2: Advanced
System ACPI Parameters
----------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
5.3.1 ACPI Settings
The ACPI Settings menu (84BIOS Menu 3) configures the Advanced Configuration and
Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State [S3 only (Suspend to…]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
elect ACPI sleep state
the system will enter
hen the SUSPEND button
is pressed.
----------------------
: Select Item
Enter
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
BIOS Menu 3: ACPI Configuration
Page 65
Page 78
E
ACPI Sleep State [S3 onl y (Suspend to RAM)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.
ICEROCK3-T10 Tablet PC
S1 only (CPU Stop
Clock)
S3 only (Suspend
to RAM)
DEFAULT
The system enters S1 (POS) sleep state. The
system appears off. The CPU is stopped; RAM is
refreshed; the system is running in a low power
mode.
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
5.3.2 RTC Wake Settings
The RTC Wake Settings menu (4BIOS Menu 4) configures RTC wake event.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Wake system with Fixed Time [Disabled]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
nable or disable System
wake on alarm event.
When enabled, System
will wake on the
dat::hr::min::sec
specified
----------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
: Select Screen
BIOS Menu 4: RTC Wake Settings
Page 66
Page 79
ICEROCK3-T10 Tablet PC
Wake System with Fixed Time [Disabled]
Use the Wake System with Fixed Time option to specify the time the system should be
roused from a suspended state.
Disabled DEFAULT
Enabled
The real time clock (RTC) cannot generate a wake
event
If selected, the following appears with values that
can be selected:
*Wake up every day
*Wake up date
*Wake up hour
*Wake up minute
*Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
Page 67
Page 80
E
I
ICEROCK3-T10 Tablet PC
5.3.3 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the
Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Configuration
Security Device Support [Disable]
Current Status Information
No Security Device Found
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
nables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
NT1A interface will not
be available.
----------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 5: Trusted Computing
Security Device Support [Disable]
Use the Security Device Support option to configure support for the security device.
Disable DEFAULT
Enable
Security device is disabled
Security device is enabled
Page 68
Page 81
E
L
T
D
ICEROCK3-T10 Tablet PC
5.3.4 CPU Configuration
Use the CPU Configuration menu (584BIOS Menu 6) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Core(TM) i7-3517UE CPU @ 1.70GHz
CPU Signature 306a9
Microcode Patch 13
Max CPU Speed 1700 MHz
Min CPU Speed 800 MHz
CPU Speed 1600 MHz
Processor Cores 2
Intel HT Technology Supported
Intel VT-x Technology Supported
Intel SMX Technology Supported
64-bit Supported
L1 Data Cache 32 KB x 2
L1 Code Cache 32 KB x 2
L2 Cache 256 KB x 2
L3 Cache 4096 KB
Hyper-Threading [Enabled]
Intel Virtualization Technology [Disabled]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
nable for Windows XP and
inux (OS optimized for
Hyper-Threading
echnology) and Disabled
for other OS (OS not
optimized for
Hyper-Threading
Technology). When
isabled only thread per
enabled core is enabled.
----------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 6: CPU Configuration
The CPU Configuration menu (
CPU Signature: Lists the CPU signature value.
Microcode Patch: Lists the microcode patch being used.
Max CPU Speed: Lists the maximum CPU processing speed.
Min CPU Speed: Lists the minimum CPU processing speed.
CPU Speed: Lists the CPU processing speed.
Processor Cores: Lists the number of the processor core
Intel HT Technology: Indicates if Intel HT Technology is supported by the CPU.
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
584BIOS Menu 6) lists the following CPU details:
Page 69
Page 82
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
64-bit: Indicates if 64-bit system is supported by the CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
L2 Cache: Lists the amount of storage space on the L2 cache.
L3 Cache: Lists the amount of storage space on the L3 cache.
Hyper Threading [Enabled]
Use the Hyper Threading to enable or disable the CPU hyper threading function.
ICEROCK3-T10 Tablet PC
Disabled
Enabled DEFAULT
Intel Virtualization Technology [Disabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel® Virtualization technology allows
several OSs to run on the same system at the same time.
Disabled DEFAULT
Enabled
Disables the use of hyper threading technology
Enables the use of hyper threading technology
Disables Intel Virtualization Technology.
Enables Intel Virtualization Technology.
Page 70
Page 83
ICEROCK3-T10 Tablet PC
5.3.5 SATA Configuration
Use the SATA Configuration menu (584BIOS Menu 7) to change and/or set the
configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
SATA Controller(s) [Enabled]
SATA Mode Selection [IDE]
mSATA1 (M_SATA1) Port MRMAJ5A032GC2M (30.0GB)
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable or disable SATA
Device.
---------------------
: Select Screen
: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 7: SATA Configuration
SA TA Controller(s) [Enabled]
Use the SATA Controller(s) option to configure the SATA controller(s).
Enabled DEFAULT
Disabled
SATA Mode Selection [IDE]
Use the SATA Mode Selection option to determine how SATA devices operate.
IDE DEFAULT
AHCI
Configures SATA devices as AHCI device.
Enables the on-board SATA controller(s).
Disables the on-board SATA controller(s).
Configures SATA devices as normal IDE device.
Page 71
Page 84
ICEROCK3-T10 Tablet PC
5.3.6 Intel(R) Rapid Start Technology
The Intel® Rapid Start Technology is disabled by default.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Intel(R) Rapid Start Technology [Disabled]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
---------------------
: Select Screen
: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 8: Intel(R) Rapid Start Technology
Page 72
Page 85
d
ICEROCK3-T10 Tablet PC
5.3.7 USB Configuration
Use the USB Configuration menu (584BIOS Menu 9) to read USB configuration information
and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard
Legacy USB Support [Enabled]
Mass Storage Devices:
Generic STORAGE DEVICE 0208 [Auto]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enables Legacy USB
support. AUTO option
isables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 9: USB Configuration
USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
Enabled DEFAULT
Legacy USB support enabled
Page 73
Page 86
S
o
ICEROCK3-T10 Tablet PC
Disabled
Auto
Legacy USB support disabled
Legacy USB support disabled if no USB devices are
connected
5.3.8 iWDD Serial Ports Configuration
Use the iWDD Serial Ports Configuration menu (4BIOS Menu 10) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
iWDD Serial Ports Configuration
Super IO Chip iWDD
> Serial Port 1 Configuration
> Serial Port 2 Configuration
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
erial Port 1 can be used
nly when you are using
DOCKING board.
---------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
Page 74
BIOS Menu 10: iWDD Super IO Configuration
Page 87
ICEROCK3-T10 Tablet PC
5.3.8.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (4BIOS Menu 11) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 1 Configuration
Serial Port n Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4
Change Settings [Auto]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable or Disable
Serial Port (COM)
---------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 11: Serial Port 1 Configuration Menu
5.3.8.1.1 Serial Port 1 Configuration
Use the Serial Port 1 Configuration menu to configure the serial port 1 on the docking
station.
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Disabled
Enabled DEFAULT
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Disable the serial port
Enable the serial port
Auto DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Page 75
Page 88
ICEROCK3-T10 Tablet PC
IO=3F8h;
IRQ=4
IO=3E8h;
IRQ=3, 4
IO=2F8h;
IRQ=3, 4
IO=3E8h;
IRQ=3, 4
IO=2E8h;
IRQ=3, 4
5.3.8.1.2 Serial Port 2 Configuration
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ4
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ3, 4
Disabled
Enabled DEFAULT
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Auto DEFAULT
IO=2F8h;
IRQ=3
IO=3F8h;
IRQ=3, 4
IO=2F8h;
IRQ=3, 4
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Page 76
Page 89
ICEROCK3-T10 Tablet PC
IO=3E8h;
IRQ=3, 4
IO=2E8h;
IRQ=3, 4
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ3, 4
5.3.9 H/W Monitor
The H/W Monitor menu (584BIOS Menu 12) shows the operating temperature.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
H/W Monitor
CPU Temperature :+47 C
---------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
: Select Screen
BIOS Menu 12: Hardware Health Configuration
PC Health Status
The following system parameters and values are shown. The system parameter that is
monitored is:
CPU Temperature
Page 77
Page 90
c
s
ICEROCK3-T10 Tablet PC
5.3.10 IEI Feature
Use the IEI Feature menu (84BIOS Menu 13) to configure One Key Recovery function.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
iEi Feature
Auto Recovery Function [Disabled]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Auto Recovery Function
Reboot and recover
system automatically
within 10 min, when OS
rashes. Please install
Auto Recovery API
ervice before enabling
this function
---------------------
: Select Screen
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 13: IEI Feature
Auto Recovery Function [Disabled]
Use the Auto Recovery Function BIOS option to enable or disable the auto recovery
function of the IEI One Key Recovery.
Disabled DEFAULT
Enabled
Auto recovery function disabled
Auto recovery function enabled
Page 78
Page 91
ICEROCK3-T10 Tablet PC
5.4 Chipset
Use the Chipset menu (584BIOS Menu 14) to access the PCH and System Agent (SA)
configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> PCH-IO Configuration
> System Agent (SA) Configuration
PCH Parameters
---------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 14: Chipset
Page 79
Page 92
E
ICEROCK3-T10 Tablet PC
5.4.1 PCH-IO Configuration
Use the PCH-IO Configuration menu (84BIOS Menu 15) to configure the PCH IO settings.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
PCH-IO Configuration
Azalia [Enabled]
Azalia Internal HDMI Codec [Enabled]
Camera Function(Back, CAMERA1) [Enabled]
Camera Function(Front, CAMERA2) [Enabled]
Barcode Function [Disabled]
RFID Function [Enabled]
GPS Function [Enabled]
Micro-SD Function [Enabled]
3G Radio Function [Enabled]
WIFI Radio Function [Enabled]
Bluetooth Function [Enabled]
Windows Rotation Function [Disabled]
LCD ECO Mode Function [Disabled]
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Control Detection of
the Azalia device.
Disabled = Azalia will
be unconditionally
disabled.
nabled = Azalia will be
unconditionally
Enabled.
---------------------
: Select Item
Enter
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
BIOS Menu 15: Host Bridge Chipset Configuration
Azalia [Enabled]
The Azalia option enables or disables the HD Audio controller.
Disabled
Enabled DEFAULT
Azalia Internal HDMI Codec [Enabled]
The Azalia Internal HDMI Codec option enables or disables the HDMI codec for Azalia.
Disabled
Enabled DEFAULT
The onboard HD Audio controller is disabled.
The onboard HD Audio controller is enabled.
The HDMI codec for Azalia is disabled.
The HDMI codec for Azalia is enabled.
Page 80
Page 93
ICEROCK3-T10 Tablet PC
Camera Function (Back, CAMERA1) [Enabled]
Use the Camera Function (Back, CAMERA1) option to enable or disable the camera
function on the rear panel.
Disabled
Enabled DEFAULT
Camera Function (Front, CAMERA2) [Enabled]
Use the Camera Function (Front, CAMERA2) option to enable or disable the camera
function on the front panel.
Disabled
Enabled DEFAULT
Barcode Function [Disabled]
Use the Barcode Function option to enable or disable the barcode function.
Disabled DEFAULT
Enabled
Rear camera function disabled
Rear camera function enabled
Front camera function disabled
Front camera function enabled
Barcode function disabled
Barcode function enabled
GPS Function [Enabled]
Use the GPS Function option to enable or disable the GPS function.
Disabled
Enabled DEFAULT
Micro-SD Function [Enabled]
Use the Micro-SD Function option to enable or disable the microSD card slot.
Disabled
Enabled DEFAULT
GPS function disabled
GPS function enabled
microSD card slot disabled
microSD card slot enabled
Page 81
Page 94
3G Radio Function [Enabled]
Use the 3G Radio Function option to enable or disable the 3G function.
ICEROCK3-T10 Tablet PC
Disabled
Enabled DEFAULT
WIFI Radio Function [Enabled]
Use the WIFI Radio Function option to enable or disable the Wi-Fi function.
Disabled
Enabled DEFAULT
Bluetooth Function [Enabled]
Use the Bluetooth Function option to enable or disable the Bluetooth function.
Disabled
Enabled DEFAULT
3G function disabled
3G function enabled
Wi-Fi function disabled
Wi-Fi function enabled
Bluetooth function disabled
Bluetooth function enabled
Windows Rotation Function [Disabled]
Use the Windows Rotation Function option to enable or disable the screen rotation
function.
Disabled DEFAULT
Enabled
LCD ECO Mode Function [Disabled]
Use the LCD ECO Mode Function option to enable or disable the LCD ECO mode.
Disabled DEFAULT
Enabled
Screen rotation function disabled
Screen rotation function enabled
LCD ECO mode disabled
LCD ECO mode enabled
Page 82
Page 95
ICEROCK3-T10 Tablet PC
5.4.2 System Agent (SA) Configuration
Use the System Agent (SA) Configuration menu (BIOS Menu 16) to configure the
System Agent (SA) parameters.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
VT-d [Disabled]
> Graphics Configuration
> Memory Configuration
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Check to enable VT-d
function on MCH.
---------------------
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 16: System Agent (SA) Configuration
VT-d [Disabled]
Use the VT-d option to enable or disable VT-d support.
Disabled DEFAULT
Enabled
Disables VT-d support.
Enables VT-d support.
Page 83
Page 96
5.4.2.1 Graphics Configuration
Use the Graphics Configuration menu (4BIOS Menu 17) to configure the graphics
settings
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
Graphics Configuration
Primary Display [Auto]
DVMT Pre-Allocated [256M]
DVMT Total Gfx Mem [MAX]
Primary IGFX Boot Display [VBIOS Default]
Current LCD Panel Type 1280x800 24BIT
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
ICEROCK3-T10 Tablet PC
Select which of
IGFX/PEG/PCI Graphics
device should be Primary
Display Or select SG for
Switchable Gfx.
---------------------
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 17: Graphics Configuration
Primary Display [Auto]
Use the Primary Display option to select the graphics controller used as the primary boot
device.
Auto D
IGFX
PEG
DVMT Pre-Allocated [256M]
Use the DVMT Pre-Allocated option to specify a fixed amount of memory that can be
allocated for the internal graphics device. Configuration options are listed below.
32M
64M
EFAULT
Page 84
Page 97
ICEROCK3-T10 Tablet PC
128M
256M D
EFAULT
512M
DVMT Total Gfx Mem [MAX]
Use the DVMT Total Gfx Mem option to specify the maximum amount of memory that can
be allocated for the internal graphics device. Configuration options are listed below.
128M
256M
MAX D
EFAULT
Primary IGFX Boot Display [VBIOS Default]
Use the Primary IGFX Boot Display option to select the display device used by the
system when it boots. Configuration options are listed below.
VBIOS Default
CRT
DEFAULT
LVD S
HDMI
Page 85
Page 98
5.4.2.2 Memory Configuration
Use the Memory Configuration menu (BIOS Menu 18) to display the memory
information.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
Memory Information
Memory Frequency 1333 Mhz
Total Memory 8192 MB (DDR3)
On Board Memory 4096 MB (DDR3)
Memory Slot 4096 MB (DDR3)
ICEROCK3-T10 Tablet PC
---------------------
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 18: Memory Configuration
5.5 Boot
Use the Boot menu (584BIOS Menu 19) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Boot Configuration
Boot NumLock State [On]
Quiet Boot [Enabled]
Option ROM Messages [Force BIOS]
UEFI Boot [Disabled]
Boot Option Priorities
Boot Option #1 [SATA PM: MRMAJ5A03…]
Hard Drive BBS Priorities
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Select the keyboard
NumLock state
---------------------
: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
Page 86
BIOS Menu 19: Boot
Page 99
ICEROCK3-T10 Tablet PC
Bootup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.
On DEFAULT
Off
Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
Disabled
Enabled DEFAULT
Option ROM Messages [Force BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.
Force
BIOS
Keep
Current
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Sets display mode to force BIOS.
Sets display mode to current.
Page 87
Page 100
UEFI Boot [Disabled]
Use the UEFI Boot option to enable or disable to boot from the UEFI devices.
ICEROCK3-T10 Tablet PC
Enabled
Disabled DEFAULT
Boot Option #1 [SATA PM: MRMAJ5A03…]
Use the Boot Option #1 option to specify the boot priority from the available devices.
Hard Drive BBS Priorities
Use the Hard Drive BBS Priorities option to set the order of the legacy devices in this
group.
Boot from UEFI devices is enabled.
Boot from UEFI devices is disabled.
5.6 Security
Use the Security menu (584BIOS Menu 20) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be
in the following range:
Minimum length 3
Maximum length 20
Administrator Password
User Password
HDD Security Configuration:
HDD0:MRMAJ5A032GC
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Set Administrator
Password
---------------------
: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
Page 88
BIOS Menu 20: Security
Loading...