High Performance Fanles s Embedded S ys tem with Int el® Core™ i5 -6300U/
Ce leron® 3855U processor, Dual HDMI, RS-232/422/485,
USB 3. 0, RoHS Compliant
User Manual
ECN-360A-ULT3 Embe dded System
Page ii
Date Version Changes
6 November, 2017 1.00 Initial release
Revision
ECN-360A-ULT3 Embe dded System
Page iii
Copyright
COP YRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliabilit y, design a nd functi on and d oes not r epresent a com mitm ent on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, e lectronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered tradem ark s and produc t nam es ment ioned here in are us ed for identif icatio n
purposes only and m ay be trademarks and/or registe red trademarks of their respec tive
owners.
ECN-360A-ULT3 Embe dded System
Page iv
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.
HO T SUR FAC E
This symbol indicates a hot surface that should not be touched without
taking care.
Figure 4-13: LAN LED Connector Locations
Figure 4-14: Full-size PCIe Mini Card Slot Location
Figure 4-15: Half-size PCIe Mini Slot Location
Figure 4-16: Power Button Location
Figure 4-17: Power Button Connector Location
Figure 4-18: Reset Button Connector Locati o n
Figure 4-19: RS-232 Serial Port Connector Locations
BIOS Menu 1: Main .......................................................................................................................63
BIOS Menu 2: Advanced
BIOS Menu 3: ACPI Settings
BIOS Menu 4: AMT Configuration
BIOS Menu 5: F81866 Super IO Configuration
BIOS Menu 6: Serial Port n Configuration
BIOS Menu 7: iWDD H/W Monitor
BIOS Menu 8: Smart Fan Mode Configuration
BIOS Menu 9: RTC Wake Settings
BIOS Menu 10: Serial Port Console Redirection
BIOS Menu 11: Legacy Console Redirection Settings
BIOS Menu 12: Console Redirection Settings
BIOS Menu 13: CPU Configuration
BIOS Menu 14: SATA
BIOS Menu 15: USB Configuration
BIOS Menu 16: IEI Feature
BIOS Menu 17: Chipset
BIOS Menu 18: System Agent (SA) Configuration
BIOS Menu 19: Graphics Configuration
BIOS Menu 20: LCD Control
BIOS Menu 21: Memory Configuration
BIOS Menu 22: PCH-IO Configuration
BIOS Menu 23: PCI Express Configuration
BIOS Menu 24: HD Audio Configuration
BIOS Menu 25: Security
BIOS Menu 26: Boot
BIOS Menu 27: Exit
The ECN-360A-ULT3 is a platform based on Intel® Core™ i5-6300U or Intel® Celeron®
3855U processor.
The ECN-360A-ULT3 contains two HDMI video outputs, which can be applied to
multi-display ap plication and sup port high Full HD video qualit y. The ECN-360A-ULT3 is
equipped with an abundant of I/O ports. Four USB 3.0 ports provide flexible ex pansion
options. Serial device connectivity is provided by two RS-232 ports and one
RS-232/422/485 port.
1.2 Mode l Variations
The model variations of the ECN-360A-ULT3 Series are listed below.
Model No.
ECN-360A-ULT3-i5/4G-R10
ECN-360A-ULT3-i5/WD/4G-R10 (Optional)
ECN-360A-ULT3-CE/4G-R10
ECN-360A-ULT3-CE/WD/4G-R10 (Optional)
Processor Power
Intel® Core™
i5-6300U 3.0GHz
Intel® Celeron®
3855U 1.6GHz
12 V DC 4GB memory pre-installed
9 V~36 V DC 4GB memory pre-installed
12 V DC 4GB memory pre-installed
9 V~36 V DC 4GB memory pre-installed
Memo ry
Table 1-1: ECN-360A-ULT3 Model Variations
ECN-360A-ULT3 Embe dded System
Page 3
1.3 Features
The ECN-360A-ULT3 features are listed below:
On-board CPU
» i5-6300U dual-core up t o 3.0GHz
» 3855U dual-core up to 1.6GHz
Two 2.5" SATA 6Gb/s HDD/SSD drive bay
Operating temperature: -20°C ~ 60°C
Two flexible E-Window for modularized expansion I/O
1.4 Technical Specifications
The ECN-360A-ULT3 technical specifications are listed in Table 1-2.
Specifications
Chassis
Color
Dimensions (WxDxH)
System Fan
Chassis Construction
Motherboard
Motherboard Model
SBC Size (mm)
Processor
System Memory
Storage
Black
255 x 130 x 75 mm
Fanless
SECC
NANO-ULT3
EPIC, 165 x 115
Intel® Core™ i5-6300U
Intel® Celeron® 3855U
2 x 260-pin 2133/1866 MHz dual-channel DDR4 SO-DIMMs support
up to 32GB
Pre-install 4GB DDR 4
Hard Drive
2 x 2.5” SATA HDD bay (No RAID support)
ECN-360A-ULT3 Embe dded System
Page 4
Specifications
I/O Interfaces
USB
Ethernet
C OM Po rt
Digital I/O
Display
Resolution
Audio
Wireles s
Expansions
PCIe Min i
4 x USB 3.0 ports
2 x RJ-45
LAN1: Intel® I219-LM
LAN2: Intel® I211-AT
1 x RS-232/422/485
2 x RS-232
8-bit Digital I/O
2 x HDMI
HDMI: up to 4096x2160@24Hz
1 x Line-out
2 x 802.11b/g/n (optional)
1 x Full-size PCIe Mini card slot (with SIM holder & mSATA support,
3855U do not support mSATA)
Power
Power Input
Power Consumption
Reliability
Mounting
Operating Temperature
Humidity
Operating Shock
1 x Half-size PCIe Mini card slot
*3855U belongs to Skylake ULT Base series CPU, PCIe signal
support only PCIe Gen 2
DC 12V (Optional 9~36V)
Power 1: DC jack
Power 2: Terminal block
12 V@2.4 A (Intel® i5-6300U with 4GB DDR4 memory)
Wall mount, VESA 100
-20°C~60°C with air flow (SSD)
5% ~ 95%, non-condensing
Half-sine wave shock 5G, 11ms, 3 shocks per axis
ECN-360A-ULT3 Embe dded System
Page 5
Specifications
Operating Vibration
Weight (Net/Gross)
Table 1-2: Technical Specifications
MIL-STD-810F 514.5C-2 (SSD)
2.2 kg/3 kg
1.5 Front Panel
The ECN-360A-ULT3 f r ont pane l contains:
1 x E-Window
1 x HDD LED
1 x Line-out port
1 x Power button
An overview of the front panel is shown in Figure 1-2.
Figure 1-2: ECN-360A-ULT3 Front Panel
1.6Rear Panel
The ECN-360A-ULT3 r ear pane l contains:
1 x DC jack for 12 V power input
1 x 3-pin terminal block for 9 V ~ 36 V power input for WD Model (Optional)
1 x DIO port
ECN-360A-ULT3 Embe dded System
Page 6
1 x E-Window
2 x HDMI ports
4 x USB 3.0 ports
1 x Reset button
2 x RJ-45 LAN ports
2 x RS-232 serial ports
1 x RS-232/422/485 serial port
2 x Wi-Fi antenna connectors (Optional)
An overview of the rear panel is shown in Figure 1-3 below.
Figure 1-3: ECN-360A-ULT3 Rear Panel
ECN-360A-ULT3 Embe dded System
Page 7
1.7 Dimensions
The physical dimensions are shown below:
Figure 1-4: Physical Dimensions (mm)
ECN-360A-ULT3 Embe dded System
Page 8
Chapter
2
2 Unpacking
ECN-360A-ULT3 Embe dded System
Page 9
may result in
2.1 Anti-s tatic Precautions
WARNING:
Failure to take ESD precautions during installation
permanent damage to the ECN-360A-ULT3 and severe injury to the
user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the ECN-360A-ULT3. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever t he ECN-360A-ULT3 or any other elect rical com ponent is
handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Touch any grounded conducting material before handling
the board. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the ECN-360A-ULT3, place it on
an antic-static pad. This reduces the possibility of ESD damaging the
ECN-360A-ULT3.
2.2 Unpacking Precautions
When the ECN-360A-ULT3 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 2.1.
Make sure the packing box is facing upwards so the ECN-360A-ULT3 does
not fall out of the box.
Make sure all the components shown in Section 2.3 are present.
ECN-360A-ULT3 Embe dded System
Page 10
2.3 1Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI res eller or
vendor you purchased the ECN-360A-ULT3 from or contact an IEI
sales representative directly. To contact an IEI sales representative,
please send an email to
The ECN-360A-ULT3 is shipped with the following components:
Quantity Item and Part Number Im age
Standard
1 ECN-360A-ULT3 Series
2 Mounting brackets
1 Screw set
sales@iei.com.tw.
1 Utility CD
1 One Key Recovery CD
The following table lists the optional items that can be purchased separately.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.