IEI Technology DM-F08A/R-R10, DM-F15A/PC-R10, DM-F12A/R-R10, DM-F12A/PC-R10, DM-F17A/R-R10 User Manual

...

Download

DM-F Series Monitor

DM Series Industrial Monitor

MODEL:

DM-F Series

6.5”/8”/12”/15”/17”/19”/21.5”/24” LCD Monitor

DisplayPort, HDMI, VGA, IP 65 Protection, RoHS

User Manual

Rev. 1.16 – November 25, 2016

Page I

DM-F Series Monitor

Revision

Date Version Changes

November 25, 2016 1.16 Added Section 3.3.3: Cabinet and Rack Installation (for

F19A)

September 20, 2016 1.15 Updated Section 1.3: Model Variations

Updated Section 1.7.2: DM-F12A ~ DM-F19A Connec tors Updated Section 1.8: Technic al Specifications Updated Section 1.9.6: DM-F19A Physical Dimensions

fied Section 3.3.1: Panel Mounting

Modi

fied Section 3.3.2: Cabinet and Rack Installation

Modi January 21, 2016 1.14 Added 6.5”, 8” and 19” model information August 6, 2015 1.13 Added Section 3.2.8.1: Installing RS-232 Connector April 29, 2015 1.12 Update Figure 3-2: 3-pin Terminal Block March 4, 2015 1.11 Update Section 1.6: Technical Specifications

Update Section 1.8: Physical Dimensio ns

Update Section 3.4.1: Panel Mounting (cut-out

dimensions also updated) December 23, 2014 1.10 Update to R11 version June 10, 2014 1.01 Update Section 4.4.1: Panel Mounting March 25, 2014 1.00 Initial Release

Page II

DM-F Series Monitor

Safety Instructions

Warning! Read the user manual before connecting the system to the power

source.

Vorsicht! Bitte lesen Sie die Bedienungsanleitung, bevor Sie das System an eine

Stromquelle anschließen.

Attention! Avant de brancher le système à la source d'alimentation, consultez le

mode d'emploi.

Avvertenza! Consultare il manuale utente prima di collegare il sistema all'alimentatore. Atención! Lea atentamente este manual del usuario antes de operar la fuente de alimentación.

警告！在將系統連接到電源之前，請仔細閱讀使用手冊。警告！在将系统连接到电源之前，请仔细阅读使用手册。

Warning! To prevent the system from overheating, do not operate it in an area that

exceeds the maximum operating temperature described in the user manual.

Vorsicht! Um eine Überhitzung des Systems zu vermeiden, betreiben Sie es ausschließlich im zulässigen Betriebstemperaturbereich. Dieser ist in der Bedienungsanleitung vermerkt.

Attention! Pour éviter la surchauffe du système, ne l'utilisez pas dans une zone

dont la température dépasse les limites décrits dans le mode d'emploi.

Avvertenza! Per evitare che il sistema si surriscaldi, non utilizzarlo in aree che

superino la temperatura massima d'esercizio descritta nel manuale utente.

Atención! Para evitar el excesivo calentamiento del sistema, no opere en las

condiciones de temperatura superior a lo recomendado en este manual del usuario.

警告！為防止系統過熱，不要在超過使用手冊上記載的產品工作溫度範圍之外操作

此系統。

警告！为防止系统过热，不要在超过使用手册上记载的产品工作温度范围之外操作

此系统。

Page III

DM-F Series Monitor

Warning! Use only the adapter and power cord approved for this system. Use of

another type of adapter may risk fire or explosion. Please refer to the user manual

for the power adapter specifications. Vorsicht! Nur zugelassene Netzteile und Netzkabel dürfen verwendet werden. Die Benutzung von anderen Netzteilen kann einen Brand oder eine Explosion zur Folge haben. Prüfen Sie die jeweiligen Spezifikationen in der Bedienungsanleitung. Attention! Utilisez exclusivement le câble d'alimentation et l’adaptateur

homologués pour ce système. L’utilisation d’un autre type d’adaptateur risquerait

de provoquer un incendie ou une explosion. Veuillez référer au mode d'emploi

pour les spécifications de l'adaptateur d'alimentation. Avvertenza! Utilizzare solo l'adattatore e il cavo di alimentazione approvati per

questo sistema. L'uso di un altro tipo di adattatore può causare rischio d'incendio

o esplosione. Si prega di fare riferimento al manuale utente per le specifiche

sull'alimentazione. Atención! Utilice solamente el adaptador de corriente alterna (CA) con Marcas

Conformidad otorgadas. Cualquier otro adaptador no otorgado aumenta el riesgo

de explosión o incendio. Por favor consulte el manual del usuario para las

especificaciones del adaptador de alimentación.

警告！只能使用經過認證、適用於本系統的電源變壓器與電源線。使用不適用的電

源變壓器將可能導致火災或爆炸。電源變壓器規格請參考使用手冊。

警告！只能使用经过认证，适用于本系统的电源适配器与电源线。使用不适用的电

源适配器将可能导致火灾或爆炸。电源适配器规格请参考使用手册。

Warning! Ultimate disposal of this product should be handled according to all

national laws and regulations.

Vorsicht! Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und

Gesetzen des Landes erfolgen.

Attention! La mise au rebut ou le recyclage de ce produit sont généralement soumis aux lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.

Avvertenza! Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e i regolamenti locali. Atención! La disposición final de residuos de este producto se debe cumplir con las normativas y leyes del país.

警告！本產品的廢棄處理應根據該國家的法律和規章進行。警告！本产品的废弃处理应根据该国家的法律和规章进行。

Page IV

DM-F Series Monitor

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

Page V

DM-F Series Monitor

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the

equipment or result in personal injury. Warnings should be taken

seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of

losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical

information. These messages should be read carefully as any directions

or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without

taking care.

Page VI

DM-F Series Monitor

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 OVERVIEW.................................................................................................................. 2

1.2 FEATURES................................................................................................................... 2

1.3 MODEL VARIATIONS ................................................................................................... 3

1.4 APPLICATIONS ............................................................................................................ 3

1.5 FRONT VIEW .............................................................................................................. 4

1.6 REAR VIEW ................................................................................................................ 5

1.7 CONNECTORS ............................................................................................................. 6

1.7.1 DM-F65A and DM-F08A Connectors............................................................... 6

1.7.2 DM-F12A ~ DM-F19A Connectors...................................................................7

1.7.3 DM-F22A and DM-F24A Connectors............................................................... 7

1.8 TECHNICAL SPECIFICATIONS ...................................................................................... 8

1.9 PHYSICAL DIMENSIONS............................................................................................ 10

1.9.1 DM-F65A Physical Dimensions....................................................................... 10

1.9.2 DM-F08A Physical Dimensions........................................................................11

1.9.3 DM-F12A Physical Dimensions....................................................................... 12

1.9.4 DM-F15A Physical Dimensions....................................................................... 13

1.9.5 DM-F17A Physical Dimensions....................................................................... 14

1.9.6 DM-F19A Physical Dimensions....................................................................... 15

1.9.7 DM-F22A Physical Dimensions....................................................................... 16

1.9.8 DM-F24A Physical Dimensions....................................................................... 17

2 UNPACKING ............................................................................................................... 18

2.1 UNPACKING PROCEDURE.......................................................................................... 19

2.2 PACKING LIST........................................................................................................... 20

2.3 OPTIONAL ITEMS...................................................................................................... 21

3 INSTALLATION ......................................................................................................... 22

3.1 INSTALLATION PRECAUTIONS................................................................................... 23

3.2 EXTERNAL PERIPHERAL DEVICE CONNECTION ........................................................ 24

3.2.1 DC-in Jack....................................................................................................... 24

Page VII

DM-F Series Monitor

3.2.2 9 V–36 V Terminal Block (Optional)................................................................ 24

3.2.3 USB for Touch Panel Connector...................................................................... 25

3.2.4 VGA Connector................................................................................................ 25

3.2.5 DVI-D Connector (F65A, F08A and F19A Only)............................................ 26

3.2.6 DisplayPort Connector (F12A ~ F24A Only).................................................. 27

3.2.7 HDMI Connector (F12A, F15A, F17A, F22A and F24A Only)....................... 28

3.2.8 RS-232 Port for Touch Panel (Reserved for Resistive Touch) ......................... 28

3.2.8.1 Installing RS-232 Connector..................................................................... 29

MOUNTING THE MONITOR........................................................................................ 31

3.3

3.3.1 Panel Mounting................................................................................................ 31

3.3.2 Cabinet and Rack Installation (for F65A ~ F17A).......................................... 39

3.3.3 Cabinet and Rack Installation (for F19A)....................................................... 41

3.3.4 Wall Mounting.................................................................................................. 44

3.3.5 Stand Installation............................................................................................. 46

3.3.6 Arm Installation ............................................................................................... 47

4 ON-SCREEN-DISPLAY (OSD) CONTROLS.......................................................... 49

4.1

OSD KEYPAD........................................................................................................... 50

4.2 OSD MENU STRUCTURE .......................................................................................... 52

4.3 USING THE OSD....................................................................................................... 53

4.3.1 Image Menu ..................................................................................................... 53

4.3.1.1 Color Setting............................................................................................. 54

4.3.2 Display Menu................................................................................................... 55

4.3.3 System Menu .................................................................................................... 56

4.3.3.1 Input.......................................................................................................... 57

4.3.3.2 OSD Settings............................................................................................. 58

5 SOFTWARE DRIVERS.............................................................................................. 59

INTRODUCTION......................................................................................................... 60

5.1

5.2 RS-232 OR USB TOUCHSCREEN............................................................................... 60

5.3 TOUCH PANEL DRIVER INSTALLATION...................................................................... 61

5.4 CHANGE THE TOUCHSCREEN INTERFACE.................................................................. 65

5.5 CALIBRATING THE TOUCHSCREEN............................................................................ 65

6 AD BOARDS ................................................................................................................ 68

6.1 AD BOARD OVERVIEW............................................................................................. 69

Page VIII

DM-F Series Monitor

AV-6038 AD BOARD................................................................................................ 69

6.2

6.2.1 AV-6038 Peripheral Interface Connectors....................................................... 70

6.2.2 Backlight Inverter Connector (INVERTER1) .................................................. 71

6.2.3 LVDS Connector (LVDS1) ............................................................................... 71

6.2.4 OSD Keypad Connector (CN14)...................................................................... 72

6.2.5 Power Input Connector (CN9)......................................................................... 72

6.2.6 RS-232 Connector for Touchscreen (RS232_1)............................................... 72

6.2.7 USB Connector for Touchscreen (USB_TOUCH1)......................................... 73

6.2.8 Touchscreen Connector (J1)............................................................................ 73

6.2.9 LVDS Panel Voltage Select Jumper (JP2) ....................................................... 73

6.2.10 EIDE Firmware Update Jumper (JP3).......................................................... 73

6.3

AV-60381 AD BOARD.............................................................................................. 74

6.3.1 AV-60381 Peripheral Interface Connectors..................................................... 74

6.3.2 Backlight Inverter Connector (INVERTER1) .................................................. 75

6.3.3 LVDS Connector (LVDS1) ............................................................................... 76

6.3.4 OSD Keypad Connector (KEYPAD1) .............................................................. 76

6.3.5 Power Input Connector (PWR2)...................................................................... 77

6.3.6 RS-232 Connector for Touchscreen (RS232_1)............................................... 77

6.3.7 USB Connector for Touchscreen (USB_TOUCH1)......................................... 77

6.3.8 Touchscreen Connector (J1)............................................................................ 77

6.3.9 VGA Connector (VGA2)................................................................................... 78

6.3.10 Backlight Voltage Select Jumper (JP5).......................................................... 78

6.3.11 LVDS Panel Voltage Select Jumper (JP2)...................................................... 78

6.3.12 Power Input Setting Jumper (JP4)................................................................. 79

6.3.13 Touchscreen Type Select Jumper (JP1).......................................................... 79

A REGULATORY COMPLIANCE.............................................................................. 80

B SAFETY PRECAUTIONS......................................................................................... 82

SAFETY PRECAUTIONS............................................................................................. 83

B.1

B.1.1 General Safety Precautions............................................................................. 83

B.1.2 Anti-static Precautions.................................................................................... 84

B.1.3 Product Disposal............................................................................................. 85

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 86

B.2.1 Maintenance and Cleaning.............................................................................. 86

B.2.2 Cleaning Tools................................................................................................. 86

Page IX

DM-F Series Monitor

C SMARTOSD................................................................................................................ 88

IEI SMARTOSD QUICK INSTALLATION GUIDE ......................................................... 89

C.1

C.2 PRE-INSTALLATION NOTICE..................................................................................... 89

C.3 SMARTOSD INSTALLATION...................................................................................... 89

C.4 SOFTWARE ILLUSTRATION ....................................................................................... 92

C.4.1 Manage Page................................................................................................... 95

C.4.2 EDID Page...................................................................................................... 96

C.4.3 Image Page...................................................................................................... 97

C.4.4 Display Page (for analog signal).................................................................... 98

C.4.5 Color Page ...................................................................................................... 99

C.4.6 PIP Page........................................................................................................ 100

C.4.7 System Page................................................................................................... 101

C.4.8 About Page .................................................................................................... 102

C.5

SMARTOSD FAQ................................................................................................... 103

C.5.1 Windows 2000 Installation Failure............................................................... 103

C.5.2 Vista Installation Failure............................................................................... 103

C.5.3 Model Failure................................................................................................ 104

C.5.4 DDC Port Failure ......................................................................................... 105

Page X

DM-F Series Monitor

List of Figures

Figure 1-1: DM-F Series .................................................................................................................2

Figure 1-2: Typical Monitor Front View........................................................................................4

Figure 1-3: 6.5” and 8” Rear View.................................................................................................5

Figure 1-4: 12”–24” Rear View ......................................................................................................5

Figure 1-5: Bottom Panel Connectors (DM-F65A/08A)...............................................................6

Figure 1-6: Side Panel Connectors (DM-F65A/08A)....................................................................6

Figure 1-7: Bottom Panel Connectors (DM-F12A/15A/17A/19A)................................................7

Figure 1-8: Side Panel Connector (DM-F12A/15A/17A/19A).......................................................7

Figure 1-9: Bottom Panel Connectors (DM-F22A/24A)...............................................................7

Figure 1-10: DM-F65A Physical Dimensions (Unit: mm) ..........................................................10

Figure 1-11: DM-F08A Physical Dimensions (Unit: mm) ..........................................................11

Figure 1-12: DM-F12A Physical Dimensions (Unit: mm) ..........................................................12

Figure 1-13: DM-F15A Physical Dimensions (Unit: mm) ..........................................................13

Figure 1-14: DM-F17A Physical Dimensions (Unit: mm) ..........................................................14

Figure 1-15: DM-F19A Physical Dimensions (Unit: mm) ..........................................................15

Figure 1-16: DM-F22A Physical Dimensions (Unit: mm) ..........................................................16

Figure 1-17: DM-F24A Physical Dimensions (Unit: mm) ..........................................................17

Figure 3-1: DC Jack......................................................................................................................24

Figure 3-2: 3-pin Terminal Block.................................................................................................24

Figure 3-3: USB Touch Panel Connector...................................................................................25

Figure 3-4: VGA Connector .........................................................................................................25

Figure 3-5: DVI-D connector........................................................................................................26

Figure 3-6: DisplayPort connector..............................................................................................27

Figure 3-7: HDMI Connector........................................................................................................28

Figure 3-8: RS-232 Touch Panel Connector ..............................................................................29

Figure 3-9: Rear Panel Retention Screw Removal (6.5” & 8”) .................................................29

Figure 3-10: Rear Panel Retention Screw Removal (12”–24”).................................................30

Figure 3-11: Connecting RS-232 Cable ......................................................................................30

Figure 3-12: Hex Jack Screws for Securing RS-232 Connector..............................................31

Figure 3-13: Mounting Clamps Holder........................................................................................32

Page XI

Figure 3-14: Mounting Clamps....................................................................................................32

Figure 3-15: DM-F65A Cutout Dimensions (Unit: mm) .............................................................33

Figure 3-16: DM-F08A Cutout Dimensions (Unit: mm) .............................................................33

Figure 3-17: DM-F12A Cutout Dimensions (Unit: mm) .............................................................33

Figure 3-18: DM-F15A Cutout Dimensions (Unit: mm) .............................................................34

Figure 3-19: DM-F17A Cutout Dimensions (Unit: mm) .............................................................34

Figure 3-20: DM-F19A Cutout Dimensions (Unit: mm) .............................................................34

Figure 3-21: DM-F22A Cutout Dimensions (Unit: mm) .............................................................35

Figure 3-22: DM-F24A Cutout Dimensions (Unit: mm) .............................................................35

Figure 3-23: Secure the Mounting Clamp Holders....................................................................36

Figure 3-24: Slide into the Panel.................................................................................................36

Figure 3-25: Panel Mounting Clamp Installation.......................................................................37

Figure 3-26: Mounting Clamps Holder Dimensions..................................................................37

Figure 3-27: Ultra Set Plate Dimensions....................................................................................38

DM-F Series Monitor

Figure 3-28: Bolt Dimensions......................................................................................................38

Figure 3-29: Steering Button Dimensions..................................................................................38

Figure 3-30: Secure the Mounting Clamp Holders....................................................................39

Figure 3-31: Slide into the Rack/Cabinet Bracket .....................................................................40

Figure 3-32: Secure the Rack/Cabinet Bracket..........................................................................40

Figure 3-33: Install into a Rack/Cabinet .....................................................................................41

Figure 3-34: Slide DM-F19A into the Rack/Cabinet Bracket.....................................................42

Figure 3-35: Secure the Mounting Brackets..............................................................................42

Figure 3-36: Install DM-F19A into a Rack/Cabinet.....................................................................43

Figure 3-37: Attach Wall Mounting Kit to the Wall ....................................................................44

Figure 3-38: Hook Onto Wall Mounting Kit ................................................................................45

Figure 3-39: Tighten Retention Screw........................................................................................45

Figure 3-40: VESA Mounting Holes (6.5” & 8”)..........................................................................46

Figure 3-41: VESA Mounting Holes (12”–24”)...........................................................................46

Figure 3-42: Monitor Stand Mounting.........................................................................................47

Figure 3-43: Monitor Arm Mounting............................................................................................48

Figure 4-1: OSD Keypad for 6.5” and 8” Monitors....................................................................50

Figure 4-2: OSD Keypad for 12”–24” Monitors..........................................................................51

Figure 4-3: Image Menu ...............................................................................................................53

Figure 4-4: Color Settings............................................................................................................54

Figure 4-5: Display Menu.............................................................................................................55

Page XII

DM-F Series Monitor

Figure 4-6: System Menu.............................................................................................................56

Figure 4-7: Input Options.............................................................................................................57

Figure 4-8: OSD Settings Menu...................................................................................................58

Figure 5-1: Setup Icon..................................................................................................................62

Figure 5-2: Welcome Screen .......................................................................................................62

Figure 5-3: License Agreement...................................................................................................63

Figure 5-4: Initiate Install .............................................................................................................63

Figure 5-5: Installation Starts......................................................................................................64

Figure 5-6: Finish Installation......................................................................................................64

Figure 5-7: PenMount Monitor Icon............................................................................................65

Figure 5-8: PenMount Monitor Popup Menu..............................................................................66

Figure 5-9: Configuration Screen................................................................................................66

Figure 5-10: Calibration Initiation Screen..................................................................................67

Figure 5-11: Calibration Screen ..................................................................................................67

Figure 6-1: AV-6038 AD Board Layout Diagram........................................................................69

Figure 6-2: AV-60381 AD Board Layout Diagram......................................................................74

Page XIII

DM-F Series Monitor

List of Tables

Table 1-1: DM-F Series Model Variations.....................................................................................3

Table 1-2: DM-F Series Specifications..........................................................................................9

Table 2-1: Packing List.................................................................................................................20

Table 3-1: USB Touch Panel Connector Pinouts ......................................................................25

Table 3-2: VGA Connector Pinouts.............................................................................................25

Table 3-3: DVI-D Connector Pinouts...........................................................................................26

Table 3-4: Display Port Connector Pinouts ...............................................................................27

Table 3-5: HDMI Connector Pinouts ...........................................................................................28

Table 3-6: RS-232 Touch Panel Connector Pinouts..................................................................28

Table 3-7: Panel Mounting Clamps.............................................................................................32

Table 4-1: OSD Control Buttons for 6.5” and 8” Monitors .......................................................50

Table 4-2: OSD Control Buttons for 12”–24” Monitors.............................................................51

Table 4-3: OSD Menu Structure...................................................................................................52

Table 6-1: AV-6038 Peripheral Interface Connectors................................................................70

Table 6-2: Backlight Inverter Connector (INVERTER1) Pinouts..............................................71

Table 6-3: LVDS Connector (LVDS1) Pinouts............................................................................71

Table 6-4: OSD Keypad Connector (CN14) Pinouts..................................................................72

Table 6-5: Power Input Connector (CN9) Pinouts.....................................................................72

Table 6-6: RS-232 Connector for Touchscreen (RS232_1) Pinouts ........................................72

Table 6-7: USB Connector for Touchscreen (USB_TOUCH1) Pinouts....................................73

Table 6-8: Touchscreen Connector (J1) Pinouts.......................................................................73

Table 6-9: LVDS Panel Voltage Select Jumper (JP2) Pinouts..................................................73

Table 6-10: EIDE Firmware Update Jumper (JP3) Pinouts.......................................................73

Table 6-11: AV-60381 Peripheral Interface Connectors............................................................75

Table 6-12: Backlight Inverter Connector (INVERTER1) Pinouts............................................75

Table 6-13: LVDS Connector (LVDS1) Pinouts..........................................................................76

Table 6-14: OSD Keypad Connector (KEYPAD1) Pinouts........................................................76

Table 6-15: Power Input Connector (PWR2) Pinouts................................................................77

Table 6-16: RS-232 Connector for Touchscreen (RS232_1) Pinouts ......................................77

Table 6-17: USB Connector for Touchscreen (USB_TOUCH1) Pinouts..................................77

Table 6-18: Touchscreen Connector (J1) Pinouts.....................................................................78

Page XIV

DM-F Series Monitor

Table 6-19: VGA Connector (VGA2) Pinouts .............................................................................78

Table 6-20: Backlight Voltage Select Jumper (JP5) Pinouts....................................................78

Table 6-21: LVDS Panel Voltage Select Jumper (JP2) Pinouts................................................78

Table 6-22: Power Input Setting Jumper (JP4) Pinouts............................................................79

Table 6-23: Touchscreen Type Select Jumper (JP1) Pinouts..................................................79

Table C-1: SmartOSD Menu Structure........................................................................................94

Page XV

DM-F Series Monitor

Chapter

1 Introduction

Page 1

1.1 Overview

Figure 1-1: DM-F Series

DM-F Series Monitor

The DM-F series LCD monitor is the latest member of IEI’s line of sophisticated LCD

designs with flat bezel. It is designed to fit industrial automation, or any other applications

that require minimum installation space and flexible configuration. The flat front panel

provides IP 65 protection, which effectively wards off dust and water. Flexible analog or

digital interfaces are provided for ease of connection with a management computer.

1.2 Features

The DM-F series have the following standard features:

 Robust IP 65 aluminum front bezel

 Aesthetic ultra-thin bezel for seamless panel mount installation

 Wide range DC input: 9 V–36 V or 12 V

 Flexible video input solution: VGA, HDMI, DisplayPort or DVI-D

 Resistive single touch or projected capacitive multi-touch options available

Page 2

DM-F Series Monitor

1.3 Model Variations

The DM-F series LCD monitor base models have a variety of variants. The model

variations are listed in

Model Number LCD Touchscreen Power VGA HDMI/DVI DisplayPort

DM-F65A/R-R10 6.5” Resistive 12 V Yes DM-F08A/R-R10 8” Resistive 12 V Yes DM-F12A/R-R10 DM-F12A/PC-R10 DM-F15A/R-R10 Resistive 9~36 V Yes DM-F15A/PC-R10 DM-F17A/R-R10 DM-F17A/PC-R10 DM-F19A/R-R10 DM-F19A/PC-R10 DM-F22A/PC-R10 21.5” Capacitive 9~36 V Yes DM-F24A/PC-R10 24” Capacitive 9~36 V Yes

4Table 1-1.

12”

15”

17”

19”

Resistive 9~36 V Yes

Capacitive 9~36 V Yes

Resistive 9~36 V Yes

Capacitive 9~36 V Yes

Resistive 9~36 V Yes

Capacitive 9~36 V Yes

DVI-D No DVI-D No

HDMI Yes HDMI Yes HDMI Yes HDMI Yes HDMI Yes

HDMI Yes DVI-D Yes DVI-D Yes

HDMI Yes

Table 1-1: DM-F Series Model Variations

1.4 Applications

The DM-F series LCD monitor is designed for rigorous industrial environments where it

may be exposed to both heat and moisture. Its durability and strength also makes it an

ideal choice for public access computers. Some possible applications include:

 Digital surveillance

 Multimedia advertising platform

 General Computing

o Computer-based testing center o General purpose information system o Mobile nursing station o Interactive education use

 Automation & Control

o Plant environment monitoring o Factory automation HMI terminal

Page 3

o Shop-floor/MES control

 Self-service Kiosk

o Full-service receptionist kiosk o Hospital self-registration terminal o Interactive photo kiosk o Video rental kiosk o Self-service POS terminal

1.5 Front View

The front of the DM-F series LCD monitor is a flat panel LCD screen surrounded by an

aluminum frame.

4Figure 1-2 shows a typical monitor front view.

DM-F Series Monitor

Page 4

Figure 1-2: Typical Monitor Front View

DM-F Series Monitor

1.6 Rear View

The rear panel provides access to retention screw holes that support VESA mounting. A

5-key/7-key membrane OSD keypad is also located on the rear panel.

The following diagrams show the rear panel of the DM-F series.

Figure 1-3: 6.5” and 8” Rear View

Figure 1-4: 12”–24” Rear View

Page 5

1.7 Connectors

The following sections show the I/O interfaces of the DM-F series LCD monitor. All

DM-F Series Monitor

connectors are fully described in Section

1.7.1 DM-F65A and DM-F08A Connectors

Figure 1-5: Bottom Panel Connectors (DM-F65A/08A)

43.2.

Page 6

Figure 1-6: Side Panel Connectors (DM-F65A/08A)

DM-F Series Monitor

1.7.2 DM-F12A ~ DM-F19A Connectors

Figure 1-7: Bottom Panel Connectors (DM-F12A/15A/17A/19A)

Figure 1-8: Side Panel Connector (DM-F12A/15A/17A/19A)

1.7.3 DM-F22A and DM-F24A Connectors

Figure 1-9: Bottom Panel Connectors (DM-F22A/24A)

Page 7

DM-F Series Monitor

1.8 Technical Specifications

4Table 1-2 shows the DM-F series technical specifications.

Model DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A LCD Display 6.5” (4:3) 8” (4:3) 12” (4:3) 15” (4:3) 17” (5:4) 19” (5:4) 21.5” (16 :9) 24” (16:9) Max. Resolution 640x480 800x600 1024 x768 1024 x768 1280x1024 1280x1024 1920x1080 1920x1080 Brightness Contrast Ratio 600:1 500:1 700:1 800:1 1000:1 1000:1 1000:1 3000:1 LCD Color 16.2M 262K 16.2M 16.2M 16.7M 16.7M 16.7M 16.7M Pixel Pitch (mm) 0.207 x

Viewing Angle (H/V) Backlight MTBF (Hrs) Touchscreen 5-wire resistive type 5-wire resistive type or projected capacitive type Projected capacitive type Touch Controller

AD Board AV-60381 AV-60381 AV-6038 AV-6038 AV-6038 AV-6038 AV-6038 AV-6038 OSD Button 5-key 5-key 7-key 7-key 7-key 7-key 7-key 7-key Smart OSD Yes Yes Yes Yes Yes Yes Yes Yes Dimensions (mm)

(cd/m²)

800 500 600 450 350 350 250 250

0.0675 x

0.207

160°/140° 140°/120° 160°/140°

50,000 50,000 50,000 70,000 50,000 50,000 30,000 30,000

Penmount 6000

191.8 x

0.2025

222.2 x

0.24 x

0.24

Resistive type: Penmount 6000 Projected capacitive type: EETI EXC7200

322.2 x

0.29 x

0.29

160°/150° 170°/160° 170°/160° 170°/160° 178°/178°

378.5 x

0.26 x

0.26

408.4 x

0.294 x

0.294

447.4 x

0.25 x

0.25

550.4 x

0.28 x

0.28

EETI EXC3000

600 x

(W x H x D)

Cutout Dimensions (W x H) (mm) Weight (kg) (Net/Gross) Enclosure Color Black C Black C Black C Black C Black C Black C Black C Black C Front Frame Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Rear Cover Sheet

VESA Mount 75 75 100 100 100 100 100 100

Page 8

154.36 x

42.88

180 x 140 206 x 154 305 x 245

1.1/2.6 1.33/4.5 2.7/4.9 3.5/5.5 4.4/7.1 5.4/8.4 6.3/9.6 7.6/10.9

Metal

182.2 x

42.7

Sheet Metal

262.2 x

40.5

Sheet Metal

303 x

43.2

361 x 286 391 x 324 430 x 355 532 x 340 577 x 359

Sheet Metal

341.4 x

49.3

Sheet Metal

372.4 x

49.57

Sheet Metal

358.4 x

49.1

Sheet Metal

382 x

49.4

Sheet Metal

DM-F Series Monitor

Model DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A Optional Mounting Kit

Operating Temp.

Storage Temp. -20°C ~ 70°C -20°C ~ 60°C Humidity 10% ~ 95% (non-condensing) I/O Ports

Reserved Ports 1 x RS-232 (for resistive touch) N/A Power 1 x Lockable DC-in jack

Wall Rack Panel Arm Stand

-20°C ~ 60°C (with air flow)

1 x VGA 1 x DVI 1 x USB 2.0 (for touch)

Wall Rack Panel Arm Stand

1 x VGA 1 x HDMI 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)

Wall Rack Panel Arm Stand

Wall

Rack

Panel

Arm

Stand

1 x VGA 1 x HDMI (17” only) 1 x DVI (19” only) 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)

Wall Panel Arm Stand

-10°C ~ 50°C (with air flow)

1 x VGA 1 x HDMI 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)

Wall Panel Arm Stand

(12 V) Optional 9V - 36V power input terminal block

Power

12V@0.5A 12V@0.5A

Consumption IP Level IP 65 compliant front panel Safety & EMC CE, FCC

Table 1-2: DM-F Series Specifications

1 x Lockable DC-in jack (9 V - 36 V) 1 x Power input terminal block (9 V - 36 V)

9V@2.2A 36V@0.5A

9V@1.6A 36V@0.4A

9V@2.6A 36V@0.6A

9V@3.3A 36V@0.8A

9V@2.5A 36V@0.6A

9V@3.4A 36V@0.8A

Page 9

1.9 Physical Dimensions

The following sections describe the physical dimensions for each model of the DM-F

series LCD monitor.

1.9.1 DM-F65A Physical Dimensions

The physical dimensions of the DM-F65A are shown in 4Figure 1-12.

DM-F Series Monitor

Page 10

Figure 1-10: DM-F65A Physical Dimensions (Unit: mm)

DM-F Series Monitor

1.9.2 DM-F08A Physical Dimensions

The physical dimensions of the DM-F08A are shown in 4Figure 1-12.

Figure 1-11: DM-F08A Physical Dimensions (Unit: mm)

Page 11

1.9.3 DM-F12A Physical Dimensions

The physical dimensions of the DM-F12A are shown in 4Figure 1-12.

DM-F Series Monitor

Page 12

Figure 1-12: DM-F12A Physical Dimensions (Unit: mm)

DM-F Series Monitor

1.9.4 DM-F15A Physical Dimensions

The physical dimensions of the DM-F15A are shown in 4Figure 1-13.

Figure 1-13: DM-F15A Physical Dimensions (Unit: mm)

Page 13

1.9.5 DM-F17A Physical Dimensions

The physical dimensions of the DM-F17A are shown in 4Figure 1-14.

DM-F Series Monitor

Page 14

Figure 1-14: DM-F17A Physical Dimensions (Unit: mm)

DM-F Series Monitor

1.9.6 DM-F19A Physical Dimensions

The physical dimensions of the DM-F19A are shown in 4Figure 1-12.

Figure 1-15: DM-F19A Physical Dimensions (Unit: mm)

Page 15

1.9.7 DM-F22A Physical Dimensions

The physical dimensions of the DM-F22A are shown in 4Figure 1-16.

DM-F Series Monitor

Page 16

Figure 1-16: DM-F22A Physical Dimensions (Unit: mm)

DM-F Series Monitor

1.9.8 DM-F24A Physical Dimensions

The physical dimensions of the DM-F24A are shown in 4Figure 1-17.

Figure 1-17: DM-F24A Physical Dimensions (Unit: mm)

Page 17

DM-F Series Monitor

Chapter

2 Unpacking

Page 18

DM-F Series Monitor

2.1 Unpacking Procedure

To unpack the DM-F series LCD monitor, follow the steps below:

WARNING:

The front side LCD screen has a protective plastic cover stuck to the

screen. Only remove the plastic cover after the DM-F series LCD monitor

has been properly installed. This ensures the screen is protected during the

installation process.

Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

external (second) box.

Step 2: Open the external (second) box.

Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

internal (first) box.

Step 4: Lift the monitor out of the boxes.

Step 5: Remove both polystyrene ends, one from each side.

Step 6: Pull the plastic cover off the DM-F series LCD monitor.

Step 7: Make sure all the components listed in the packing list are present. Step 0:

Page 19

2.2 Packing List

The DM-F series monitor is shipped with the following components:

Quantity Item Image

1 DM-F series

1 USB cable (for touchscreen)

(P/N: 32001-006100-100-RS)

1 VGA cable

DM-F Series Monitor

(P/N: 32000-036200-RS)

1 Touch pen (resistive touch only)

(P/N: 43125-0002C0-00-RS)

1 60W 12V DC adapter with lockable

connector (6.5” and 8” models only) (P/N: 63040-010060-120-RS)

1 Utility CD (drivers and user manual)

Table 2-1: Packing List

If any of the above items are missing or damaged, contact the distributor or sales

representative immediately.

Page 20

DM-F Series Monitor

2.3 Optional Items

The following items are optional accessories for the DM-F series monitor:

Item DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A Arm

Stand

Wall Mount Kit

Panel Mount Kit

Rack Mount Kit

Cable Cover

RS-232 Touch

Cable Kit

HDMI Cable

DVI Cable

Display Port

Cable

Power Adapter

ARM-11-RS ARM-31-RS

STAND-B08

AFLWK-12 WK-190MS-R10

FPK-04-R10 FPK-01-R10 FPK-02-R10 FPK-03-R10

FRK65-R10 FRK08-R10 FRK12-R10 FRK15-R10 FRK17-R10 FRK19-R10 N/A

N/A DM-F-CC01-R10 DM-F-CC02-R10

N/A 32012-000100-200-RS N/A 32012-000100-200-RS

32000-086600-RS N/A 32000-086600-RS N/A

N/A 32004-000200-100-RS

N/A 63040-010060-120-RS (60W 12V DC adapter with lockable connector)

STAND-A12-RS

STAND-A19-RS, STAND-C19-RS or STAND-A21-RS

STAND-C12-RS

DM-F-COMKIT-R10 N/A

Page 21

DM-F Series Monitor

Chapter

3 Installation

Page 22

DM-F Series Monitor

3.1 Installation Precautions

When installing the DM-F series LCD monitor, please follow the precautions listed below:

 Read the user manual: The user manual provides a complete description of

the DM-F series LCD monitor, installation instructions and configuration

options.

 DANGER! Disconnect Power: Power to the monitor must be disconnected

when installing the DM-F series LCD monitor, or before any attempt is made

to access the rear panel. Electric shock and personal injury might occur if the

rear panel of the monitor is opened while the power cord is still connected to

an electrical outlet.

 Qualified Personnel: The DM-F series LCD monitor must be installed and

operated only by trained and qualified personnel. Maintenance, upgrades, or

repairs may only be carried out by qualified personnel who are familiar with

the associated dangers.

 Mounting: Since the monitor may weigh up to 8 kg (not including a swing arm

or other accessories), please ensure at least two people assist with mounting

the monitor.

 Air Circulation: Make sure there is sufficient air circulation when installing the

monitor. Leave at least 5 cm of clearance around the monitor to prevent

overheating.

 Grounding: The monitor should be properly grounded. The voltage feeds

must not be overloaded. Adjust the cabling and provide external overcharge

protection per the electrical values indicated on the label attached to the back

of the monitor.

 Anti-static Discharge : The rear panel of the monitor must to be removed to

configure the monitor’s AD board. When doing so, be sure the monitor is

disconnected from its power source and take all necessary safety precautions

to avoid electrocution and static discharge to the AD board. The use of a

grounded wrist strap and an anti-static work pad is recommended.

Page 23

3.2 External Peripheral Device Connection

The external I/O connector pinouts of the DM-F series industrial monitors are described in

the following sections.

3.2.1 DC-in Jack

The lockable power connector connects to the power adapter and provides power to the

monitor. Supported power voltage is varied among models as described below:

 DM-F65A/08A: 12 V  DM-F12A/15A/17A/19A/22A/24A: 9 V–36 V

DM-F Series Monitor

Figure 3-1: DC Jack

3.2.2 9 V–36 V Terminal Block (Optional)

Connect the leads of 9 V–36 V DC power supply into the terminal block. Make sure that

the power and ground wires are attached to the correct sockets of the connector.

Figure 3-2: 3-pin Terminal Block

Page 24

DM-F Series Monitor

3.2.3 USB for Touch Panel Connector

Use the rear panel standard USB touch panel connector to connect the monitor to the

system graphics interface.

PIN DESCRIPTION PIN DESCRIPTION

1 VCC 2 USB20_N11 3 USB20_P11 4 GND

Table 3-1: USB Touch Panel Connector Pinouts

Figure 3-3: USB Touch Panel Connector

3.2.4 VGA Connector

Use the rear panel standard 15-pin female VGA connector to connect the monitor to the

system graphics interface.

PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION

1 RED 6 GROUND 11 NC 2 GREEN 7 GROUND 12 DDCDAT 3 BLUE 8 GROUND 13 HSYNC 4 NC 9 NC 14 VSYNC 5 GROUND 10 GROUND 15 DDCCLK

Table 3-2: VGA Connector Pinouts

Figure 3-4: VGA Connector

Page 25

3.2.5 DVI-D Connector (F65A, F08A and F19A Only)

The 24-pin Digital Visual Interface (DVI) connector connects to high-speed,

high-resolution digital displays. The DVI-D connector supports only digital signals.

PIN DESCRIPTION PIN DESCRIPTION

DM-F Series Monitor

1 2 3 4 5 6 7 8 9 10 11 12

Table 3-3: DVI-D Connector Pinouts

TMDS Data2TMDS Data2+ GND N/C N/C DDC Clock [SCL] DDC Data [SDA] Analog vertical sync TMDS Data1TMDS Data1+ GND NC

13 14 15 16 17 18 19 20 21 22 23 24

NC PVDD1 GND GND TMDS Data0TMDS Data0+ GND NC NC GND TMDS Clock + TMDS Clock -

Page 26

Figure 3-5: DVI-D connector

DM-F Series Monitor

3.2.6 DisplayPort Connector (F12A ~ F24A Only)

The DisplayPort connector transmits a digital signal to compatible DisplayPort display

devices such as a TV or computer screen.

PIN DESCRIPTION PIN DESCRIPTION

1 ML_L3N 2 GND 3 ML_L3P 4 ML_L2N 5 GND 6 ML_L2P 7 ML_L1N 8 GND 9 ML_L1P 10 ML_L0N 11 GND 12 ML_L0P 13 GND 14 GND 15 C_DDI0_DP_AUXP 16 GND 17 C_DDI0_DP_AUXN 18 C_DDI0_DP_HPD 19 GND 20 VCC 21 GND 22 GND 23 GND 24 GND

Table 3-4: Display Port Connector Pinouts

Figure 3-6: DisplayPort connector

Page 27

DM-F Series Monitor

3.2.7 HDMI Connector (F12A, F15A, F17A, F22A and F24A Only)

The HDMI connector connects to a display device with HDMI interface.

PIN DESCRIPTION PIN DESCRIPTION

1 HDMI_TMDS_C_DATA2 2 GND 3 HDMI_TMDS_C_DATA2# 4 HDMI_TMDS_C_DATA1 5 GND 6 HDMI_TMDS_C_DATA1# 7 HDMI_TMDS_C_DATA0 8 GND 9 HDMI_TMDS_C_DATA0# 10 HDMI_TMDS_C_CLK 11 GND 12 HDMI_TMDS_C_CLK# 13 NC 14 NC 15 HDMI_DDC_SCLK 16 HDMI_DDC_SDATA 17 GND 18 +5V_HDMI 19 HDMI_HPD

Table 3-5: HDMI Connector Pinouts

Figure 3-7: HDMI Connector

3.2.8 RS-232 Port for Touch Panel (Reserved for Resistive Touch)

Use the side panel standard RS-232 DB-9 female touch panel connector to connect the

monitor to the system graphics interface.

PIN DESCRIPTION PIN DESCRIPTION

1 N/A 6 NDSR 2 NRX 7 NRTS 3 NTX 8 N/A

Page 28

4 NDTR 9 N/A 5 GND

Table 3-6: RS-232 Touch Panel Connector Pinouts

DM-F Series Monitor

Figure 3-8: RS-232 Touch Panel Connector

3.2.8.1 Installing RS-232 Connector

If the DM-F series doesn’t have the RS-232 connector on the side panel, the user can

purchase the RS-232 Touch Cable Kit (DM-F-COMKIT-R10) and install the RS-232

connector onto the system. Please note that the RS-232 port is only available for the

resistive type models of the 6.5”–19” monitors.

Step 1: Remove the rear cover retention screws and lift the rear panel off the monitor.

Figure 3-9: Rear Panel Retention Screw Removal (6.5” & 8”)

Page 29

Figure 3-10: Rear Panel Retention Screw Removal (12”–24”)

Step 2: Remove the RS-232 knockout hole on the side panel.

Step 3: Connect the RS-232 flat cable to the internal RS-232 connector (1x9 pin,

DM-F Series Monitor

RS232_1) on the AD board. See Figure 3-11.

Page 30

Figure 3-11: Connecting RS-232 Cable

Step 4: Insert the D-sub 9 connector of the RS-232 flat cable into the hole and secure

the connector with two hex jack screws.

DM-F Series Monitor

Figure 3-12: Hex Jack Screws for Securing RS-232 Connector

Step 5: Re-install the rear panel.

3.3 Mounting the Monitor

The DM-F series LCD monitor can be mounted in a panel, cabinet, rack or wall. The

monitor can also be mounted on a monitor arm or stand. The mounting methods are

described below.

CAUTION:

When mounting the monitor take care to tighten the retention screws or

bolts until fully secure, but do not over tighten. Over tightening the

retention screws or bolts may cause them to become stripped,

rendering them useless.

3.3.1 Panel Mounting

Each model of the DM-F series LCD monitor has a series of mounting slots located on the

top, side and bottom panels for mounting the monitor to a panel.

4Table 3-7 lists the number of mounting clamps and holders required to mount the monitor

to a panel.

Model Mounting Clamps Clamp Holders

DM-F65A 8 N/A

DM-F08A 8 N/A

DM-F12A 9 9

DM-F15A 9 9

Page 31

DM-F17A 9 9

DM-F19A 10 10

DM-F22A 10 10

DM-F24A 12 12

DM-F Series Monitor

Table 3-7: Panel Mounting Clamps

Figure 3-13: Mounting Clamps Holder

Figure 3-14: Mounting Clamps

Page 32

To mount the DM-F series LCD monitor into a panel, please follow the steps below.

Step 1: Select the position on the panel to mount the monitor.

Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of

the monitor. Take care that the panel section that is cut out is smaller than the

overall size of the metal frame that surrounds the monitor but just large enough

for the rear panel of the monitor to fit through.

DM-F Series Monitor

Figure 3-15: DM-F65A Cutout Dimensions (Unit: mm)

Figure 3-16: DM-F08A Cutout Dimensions (Unit: mm)

Figure 3-17: DM-F12A Cutout Dimensions (Unit: mm)

Page 33

DM-F Series Monitor

Figure 3-18: DM-F15A Cutout Dimensions (Unit: mm)

Figure 3-19: DM-F17A Cutout Dimensions (Unit: mm)

Page 34

Figure 3-20: DM-F19A Cutout Dimensions (Unit: mm)

DM-F Series Monitor

Step 3: Secure the mounting clamps holders to the corresponding holes on the rear of

Figure 3-21: DM-F22A Cutout Dimensions (Unit: mm)

Figure 3-22: DM-F24A Cutout Dimensions (Unit: mm)

the monitor (Figure 3-23).

NOTE:

It is not required to install the clamp holders to the DM-F65A and

DM-F08A monitors for panel/rack mounting. After sliding the monitor

through the panel, simply insert the panel mounting clamps into the

pre-formed holes along the top, side and bottom panels of the

monitors. Then, tighten the screws that pass through the panel

mounting clamps until the plastic caps at the front of all the screws are

firmly secured to the panel.

Page 35

Figure 3-23: Secure the Mounting Clamp Holders

DM-F Series Monitor

Step 4: Slide the monitor through the hole until the aluminum frame is flush against the

panel (Figure 3-24).

Page 36

Figure 3-24: Slide into the Panel

DM-F Series Monitor

Step 5: Insert the panel mounting clamps into the pre-formed holes of the clamp holders

(Figure 3-25).

Step 6: T

ighten the screws that pass through the panel mounting clamps until the plastic

caps at the front of all the screws are firmly secured to the panel (Figure 3-25).

Figure 3-25: Panel Mounting Clamp Installation

The dimensions of the clamp holder and the clamp are shown in the following diagrams.

Figure 3-26: Mounting Clamps Holder Dimensions

Page 37

DM-F Series Monitor

Figure 3-27: Ultra Set Plate Dimensions

Figure 3-28: Bolt Dimensions

Figure 3-29: Steering Button Dimensions

Page 38

DM-F Series Monitor

3.3.2 Cabinet and Rack Installation (for F65A ~ F17A)

NOTE:

When purchasing a cabinet/rack installation bracket, make sure it is

compatible with both the monitor and the cabinet/rack into which the

monitor is installed.

The DM-F series LCD monitor can be installed into a cabinet or rack. The installation

procedures are similar to the panel mounting installation. To do this, please follow the

steps below:

Step 1: Secure the mounting clamps holders to the corresponding holes on the rear of

the monitor (Figure 3-30).

NOTE:

It is not required to install the clamp holders to the DM-F65A and

DM-F08A monitors for panel/rack mounting. After sliding the monitor

through the panel, simply insert the panel mounting clamps into the

pre-formed holes along the top, side and bottom panels of the

monitors.

Figure 3-30: Secure the Mounting Clamp Holders

Page 39

Step 2: Slide the rear of the DM-F series LCD monitor through the rack/cabinet bracket

DM-F Series Monitor

until the aluminum frame is flush against the front of the bracket (Figure 3-31).

Figure 3-31: Slide into the Rack/Cabinet Bracket

Step 3: Insert the panel mounting clamps into the pre-formed holes of the clamp holders

(Figure 3-32).

Step 4: T

Figure 3-32: Secure the Rack/Cabinet Bracket

ighten the screws that pass through the rack mounting clamps until the plastic

caps at the front of all the screws are firmly secured to the bracket (Figure 3-3 2).

Page 40

DM-F Series Monitor

Step 5: Slide the LCD monitor with the attached rack/cabinet bracket into a rack or

cabinet (Figure 3-33).

Figure 3-33: Install into a Rack/Cabinet

Step 6: Once the LCD monitor with the attached rack/cabinet bracket has been properly

inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-33).

3.3.3 Cabinet and Rack Installation (for F19A)

NOTE:

When purchasing a cabinet/rack installation bracket, make sure it is

compatible with both the monitor and the cabinet/rack into which the

monitor is installed.

To install the DM-F19A to a cabinet or rack, please follow the steps below:

Step 1: Slide the rear of the DM-F series LCD monitor through the rack/cabinet bracket

until the aluminum frame is flush against the front of the bracket (Figure 3-34).

Page 41

Figure 3-34: Slide DM-F19A into the Rack/Cabinet Bracket

Step 2: Secure the rack/cabinet bracket to the monitor. To do this, secure the 10

DM-F Series Monitor

mounting brackets to the corresponding screw holes on the rear of the monitor using the provided retention screws (Figure 3-35).

Page 42

Figure 3-35: Secure the Mounting Brackets

DM-F Series Monitor

Step 3: Slide the LCD monitor with the attached rack/cabinet bracket into a rack or

cabinet (Figure 3-36).

Figure 3-36: Install DM-F19A into a Rack/Cabinet

Step 4: Once the LCD monitor with the attached rack/cabinet bracket has been properly

inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-33).

Page 43

3.3.4 Wall Mounting

CAUTION:

Due to safety concerns, it is highly recommended to use the VESA

mounting kits provided by IEI for wall, stand and arm mounting. If the

VESA mounting kit is purchased separately, please make sure the

mounting kit is UL-listed.

Each model of the DM-F series LCD monitor has four holes located on the rear panel for

mounting the monitor to a wall. To mount the DM-F series LCD monitor onto a wall, please

follow the steps below.

Step 1: Attach the wall mounting kit to the mounting surface with the included screws.

DM-F Series Monitor

Make sure it is attached securely (

5Figure 3-37).

Figure 3-37: Attach Wall Mounting Kit to the Wall

Step 2: Screw the mounting screws to the mounting holes on the rear of the DM-F series

Page 44

(Figure 3-38).

Step 3: Hoo

(Figure 3-38).

k the DM-F series into the mounting holes on the wall mounting kit

DM-F Series Monitor

Figure 3-38: Hook Onto Wall Mounting Kit

Step 4: Tighten the top screw on the wall mounting kit to securely hold the DM-F series

in place. After this screw is tightened, the DM-F series should not be able to

move.

Figure 3-39: Tighten Retention Screw

Page 45

3.3.5 Stand Installation

The DM-F series LCD monitor has Video Electronics Standards Association (VESA)

standard mounting holes tapped into the rear panel. The standard holes are M4 set at

75 mm x 75 mm or 100 mm x 100 mm apart (Figure 3-40 and Figure 3-41).

DM-F Series Monitor

Figure 3-40: VESA Mounting Holes (6.5” & 8”)

Figure 3-41: VESA Mounting Holes (12”–24”)

Page 46

DM-F Series Monitor

To mount the DM-F series LCD monitor onto a stand, please follow the steps below.

Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the

monitor stand mounting plate.

Step 2: Secure the monitor to the stand with the supplied retention screws (

Figure 3-42: Monitor Stand Mounting

5Figure 3-42).

3.3.6 Arm Installation

The DM-F series LCD monitor has VESA standard mounting holes tapped into the rear

panel. The standard holes are M4 set at 75 mm x 75 mm or 100 mm x 100 mm apart

(Figure 3-40 and Figure 3-41). To mount the DM-F series

please follow the steps below.

Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the

monitor arm mounting plate.

Step 2: Secure the monitor to the arm with the supplied retention screws (Figure 3-43).

Step 0:

LCD monitor onto a monitor arm,

Page 47

DM-F Series Monitor

Figure 3-43: Monitor Arm Mounting

Page 48

DM-F Series Monitor

Chapter

4 On-Screen-Display (OSD)

Controls

Page 49

4.1 OSD Keypad

There are several on-screen-display (OSD) control buttons of the OSD keypad on the

monitor rear panel. Figure 4-1 shows the 5-key membrane OSD keypad of the 6.5”and 8”

DM-F Series Monitor

LCD monito

rs.

Figure 4-1: OSD Keypad for 6.5” and 8” Monitors

Page 50

The function of each button is described in the following table.

LCD ON/OFF Press this button to turn on or turn off the LCD screen.

AUTO

LEFT

RIGHT

Press this button to automatically adjust the screen. When inside a menu, press this button to confirm the selection o f the item. Press this button to decrease the value, or to scroll up from one selected item to another. Press this button to increase the value, or to scroll down from one selected item to another. Press this button to open the OSD window, exit the main menu or the current menu.

Table 4-1: OSD Control Buttons for 6.5” and 8” Monitors

DM-F Series Monitor

Figure 4-2 shows the 7-key membrane OSD keypad of the 12”–24” LCD monitors.

Figure 4-2: OSD Keypad for 12”–24” Monitors

The function of each button is described in the following table.

LCD on/off Press this butto n to turn on or turn off the LCD screen. Auto Press this button to automatically adjust the screen.

Left

Right Press this button to decrease the value. Up Press this button to scroll up from one selected item to another. Down Press this button to scroll down from one selected item to another.

Press this button to open the OSD window, exit the main menu or the current menu. Press this button to increase the value. When inside a menu, press this button to enter the submenu or confirm the selection of the item.

Table 4-2: OSD Control Buttons for 12”–24” Monitors

Page 51

4.2 OSD Menu Structure

5Table 4-3 shows the OSD menu structure for all models of the DM-F series LCD monitor.

Level 0 Level 1 Level 2 Value

DM-F Series Monitor

Image

Display

System

Brightness 0 to 100 Contrast 0 to 100 Sharpness -4 to 4 Color

Auto Adjust Phase 0 to 100 Clock 0 to 100 Display Position Display Modes

Input

Auto Color temp

Display Port

5000K 6500K 9300K User Reset

Gamma off Gamma 2.2

OSD Setting

Information Reset

Table 4-3: OSD Menu Structure

Page 52

VGA DVI/HDMI autoscan Timer 10sec/30sec/60sec Rotation 0°/90°/180°/270° Position Transparency 0 to 100

DM-F Series Monitor

4.3 Using the OSD

OSD menu options are described below.

4.3.1 Image Menu

Image menu features are shown in Figure 4-3.

Figure 4-3: Image Menu

The brightness option adjusts the brightness of screen. This function

Brightness

Contrast

Sharpness

Color

adjusts the offset value of ADC. Setting this value too high or too low

will affect the quality of image.

This function adjusts the gain value of ADC. Adjusting this value too

high or too low will worsen the quality of image.

Adjusts the sharpness level. This option softens the edges around

objects on the screen.

Provides options for color settings. (Figure 4-4)

Page 53

4.3.1.1 Color Setting

Color settings are shown in Figure 4-3.

DM-F Series Monitor

Figure 4-4: Color Settings

auto

Color temp

Automatically adjusts the color settings.

This item allows adjustment of the following items.

 5000k – NTSC standard Kelvin

 6500k – NTSC standard Kelvin

 9300k – NTSC standard Kelvin

 User – This item allows fine-tuning the balance among Red,

Green, and Blue color hues if images look garish or unrealistic.

Page 54

DM-F Series Monitor

4.3.2 Display Menu

Display menu features are shown in Figure 4-5.

Figure 4-5: Display Menu

Auto Adjust

Phase

Clock

Display Position

Display Mode

Automatically adjusts the LCD screen position.

Adjusts the phase control of image

Adjusts frequency to fill display

Adjusts the horizontal and vertical position of the display screen

This item allows adjustment of the Gamma.

Page 55

4.3.3 System Menu

System menu features are shown in Figure 4-6.

DM-F Series Monitor

Figure 4-6: System Menu

Input

OSD Setting

Information

Reset

Allows selection of input device to use. (Figure 4-7)

Provides options for OSD configuration. (Figure 4-8)

Provide

release date and input resolution.

Restores the default OSD settings. Note that this will restore all default

display settings.

s information on the LCD monitor, such as firmware version,

Page 56

DM-F Series Monitor

4.3.3.1 Input

Input options are shown in Figure 4-7.

Figure 4-7: Input Options

Input options are described below.

Display Port

VGA

HDMI

autoscan

This item sets the input device to display port.

This item sets the input device to VGA.

This item sets the input device to HDMI.

Selects the input device to use automatically.

Page 57

4.3.3.2 OSD Settings

The OSD settings are shown in Figure 4-8.

DM-F Series Monitor

Figure 4-8: OSD Settings Menu

OSD settings are described below.

Timer

Rotation

Position

Transparency

Determines how many seconds the OSD screen stays on screen

before it disappears when OSD is left unattended.

Adjusts the OSD rotation angle on the screen.

Adjusts the OSD position on the screen.

Adjust the transparency of the OSD menu background.

Page 58

DM-F Series Monitor

Chapter

5 Software Drivers

Page 59

5.1 Introduction

The touch panel controller enables analog resistive touch panels for four-wire, five-wire &

eight-wire models. The controller directly communicates with the PC system through the

touch panel communications interface. The controller design is superior in sensitivity,

accuracy, and friendly operation. The touch panel driver emulates the left mouse button

and the right mouse button functions.

The touch panel driver supports the following operating systems:

DM-F Series Monitor

 Microsoft

o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft

 Microsoft

o Microsoft o Microsoft o Microsoft

 Linux Kernel 2.6

 DOS

Driver installation is described below.

Windows® versions:

Windows® 2000

Windows® XP

Windows® 2003

Windows® 2008

Windows® Vista

Windows® 7

Windows® 8

Windows® CE versions:

Windows® CE 4.2

Windows® CE 5.0

Windows® CE 6.0

5.2 RS-232 or USB Touchscreen

Before installing the driver, connect the DM-F series monitor to the motherboard. The

DM-F series monitors support touchscreen modality through a USB or an RS-232

interface connection. Decide through which interface the touchscreen is to be controlled.

Page 60

DM-F Series Monitor

NOTE:

The default touchscreen interface for the DM-F series monitor is USB

interface. The RS-232 interface is only reserved for the models with

resistive type touchscreen.

 RS-232 Interface: If the touchscreen interface connection is an RS-232

connection, connect the RS-232 connector on the single board computer to

the DB-9 connector of the DM-F series monitor.

 USB Interface: If the touchscreen interface connection is a USB connection,

connect the USB connector on the single board computer to the external USB

port connector of the DM-F series monitor.

5.3 Touch Panel Driver Installation

WARNING:

Before the touchscreen driver is installed, make sure the system is

connected to the monitor with a USB cable or an RS-232 null cable.

Also, make sure the VGA connector on the system is connected to the

VGA connector on the bottom of the monitor.

To install the touch panel driver for the DM-F series, please follow the instructions below:

Step 1: Connect the DM-F series monitor to the single board computer. See above.

Step 2: Install the driver CD. Install the driver CD into the system to which the DM-F

series monitor is connected.

Step 3: Select the Touch Screen option in the menu of driver CD. The directory in

Figure 5-1 a

ppears.

Page 61

DM-F Series Monitor

Figure 5-1: Setup Icon

Step 4: Double click the setup icon in Figure 5-1.

Step 5: The W

Figure 5-2: Welcome Screen

Step 6: Click Next to continue.

elcome screen in Figure 5-2 app

ears.

Page 62

Step 7: The license agreement in Figure 5-3 a

agreement by clicking I Agree.

ppears. Accept the terms of the

DM-F Series Monitor

Figure 5-3: License Agreement

Step 8: The installation destination screen appears. See Figure 5-4. C

Figure 5-4: Initiate Install

Step 9: The installation of the program begins. See Figure 5-5.

lick Install.

Page 63

DM-F Series Monitor

Figure 5-5: Installation Starts

Step 10: When the installation is complete, the complete screen appears. See Figure 5-6.

o complete the installation process click Finish.

Figure 5-6: Finish Installation

Page 64

DM-F Series Monitor

5.4 Change the Touchscreen Interface

If the touchscreen interface must be changed from a USB interface to an RS-232 interface

or from an RS-232 interface to a USB interface, the following steps must be followed.

Step 1: Uninstall the touchscreen driver

Step 2: Remove the interface cable i.e. remove the USB cable or the RS-232 cable

Step 3: Install the new cable i.e. install the RS-232 cable or the USB cable.

Step 4: Reinstall the driver CD as described above. Step 0:

5.5 Calibrating the Touchscreen

To calibrate the touchscreen cursor with the motion of the touch pen (or finger), please

follow the steps below:

Step 1: Make sure the system is properly connected through a USB or an RS-232

interface to the DM-F series monitor.

Step 2: Make sure the touchscreen driver is properly installed.

Step 3: Locate the PenMount Monitor icon in the bottom right corner of the screen.

Figure 5-7: PenMount Monitor Icon

Step 4: Click the icon. A pop up menu appears. See Figure 5-8.

Page 65

Figure 5-8: PenMount Monitor Popup Menu

Step 5: Click Control Panel in the pop up menu shown in Figure 5-8.

DM-F Series Monitor

Step 6: The co

Figure 5-9: Configuration Screen

nfiguration screen in Figure 5-9 a

ppears.

Page 66

Step 7: Double click the PenMount 6000 icon as shown in Figure 5-9.

Step 8: The cali

Step 9: Select the Standard Calibration button as shown in Figure 5-10.

bration initiation screen in Figure 5-10 ap

pears.

DM-F Series Monitor

Figure 5-10: Calibration Initiation Screen

Step 10: The calibration screen in is shown. See Figure 5-11.

Figure 5-11: Calibration Screen

Step 11: Follow the instructions. The user is asked touch the screen at five specified

points after which the screen is calibrated. Step 0:

Page 67

DM-F Series Monitor

Chapter

6 AD Boards

Page 68

DM-F Series Monitor

6.1 AD Board Overview

The DM series LCD monitor AD board provides a wide variety of control interfaces. There

are two AD boards used for the DM series monitors: AV-6038 and AV-60381. Refer to

5Table 1-2 for a listing of DM series monitors and their associated AD board. The following

sections describe each AD board in detail.

6.2 A V-6038 AD Board

The connector locations of the AV-6038 are shown in Figure 6-1. The Pin 1 locations of

the on-board connectors are also indicated in the diagrams below. The connector pinouts

for these connectors are listed in the following sections.

Figure 6-1: AV-6038 AD Board Layout Diagram

Page 69

6.2.1 AV-6038 Peripheral Interface Connectors

5Table 6-1 shows a list of the peripheral interface connectors on the AV-6038 AD board.

Pinouts of the connectors that are used in the DM-F series can be found in the following

sections.

Connector Type Label

Backlight Inverter connector 6-pin wafer, p=2.00 mm INVERTER1

COM debug port connector 2-pin wafer, p=2.00 mm CN2

Camera connector 4-pin wafer, p=1.25 mm USB_CAM1

DisplayPort firmware connector 4-pin wafer, p=1.25 mm DP_FW1

HDMI firmware connector 4-pin wafer, p=1.25 mm HDMI_FW1

DM-F Series Monitor

Infrared connector 2-pin wafer, p=2.00 mm CN3

LVDS connector 30-pin crimp, p=1.25 mm LVDS1

OSD keypad connector 12-pin wafer, p=1.00 mm CN14

Power input connector 4-pin wafer, p=3.96 mm CN9

RS-232 connector for touchscreen 6-pin wafer, p=1.25 mm RS232_1

SPI flash connector 6-pin wafer, p=1.25 mm JSPI1

USB connector for touchscreen 4-pin wafer, p=1.25 mm USB_TOUCH1

Touchscreen connector 9-pin wafer, p=1.25 mm J1

Jumper Type Label

LVDS panel voltage select jumper 6-pin header, p=2.54 mm JP2

EIDE firmware update jumper 2-pin header, p=2.00 mm JP3

Table 6-1: AV-6038 Peripheral Interface Connectors

Page 70

DM-F Series Monitor

6.2.2 Backlight Inverter Connector (INVERTER1)

PIN NO. DESCRIPTION

1 BKL_POWER1 2 BKL_POWER1 3 ENABKL 4 BRIGHTNESS 5 GND 6 GND

Table 6-2: Backlight Inverter Connector (INVERTER1) Pinouts

6.2.3 LVDS Connector (LVDS1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 GND 2 GND 3 A0P_C 4 A0M_C 5 A1P_C 6 A1M_C 7 A2P_C 8 A2M_C 9 CLK1P_C 10 CLK1M_C 11 A3P_C 12 A3M_C 13 GND 14 GND 15 A4P_C 16 A4M_C 17 A5P_C 18 A5M_C 19 A6P_C 20 A6M_C 21 CLK2P_C 22 CLK2M_C 23 A7P_C 24 A7M_C 25 GND 26 GND 27 VCC 28 VCC 29 VCC 30 VCC

Table 6-3: LVDS Connector (LVDS1) Pinouts

Page 71

6.2.4 OSD Keypad Connector (CN14)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 +5V_OSD 2 +12V

3 OSD1 4 OSD2 5 OSD3 6 OSD4 7 OSD5 8 OSD6 9 OSD7 10 MLED8 11 GND 12 +3.3V_DVDD

Table 6-4: OSD Keypad Connector (CN14) Pinouts

6.2.5 Power Input Connector (CN9)

PIN NO. DESCRIPTION

DM-F Series Monitor

1 GND 2 GND 3 VCC 4 VCC

Table 6-5: Power Input Connector (CN9) Pinouts

6.2.6 RS-232 Connector for Touchscreen (RS232_1)

PIN NO. DESCRIPTION

1 NDSR 2 NRX 3 NRTS 4 NTX 5 NDTR 6 GND

Table 6-6: RS-232 Connector for Touchscreen (RS232_1) Pinouts

Page 72

DM-F Series Monitor

6.2.7 USB Connector for Touchscreen (USB_TOUCH1)

PIN NO. DESCRIPTION

1 VCC_TOUCH 2 D2F3 D2F+ 4 GND

Table 6-7: USB Connector for Touchscreen (USB_TOUCH1) Pinouts

6.2.8 Touchscreen Connector (J1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 X+ 2 X-

3 Y+ 4 SENSE 5 X+ 6 X7 Y+ 8 Y+ 9 GND

Table 6-8: Touchscreen Connector (J1) Pinouts

6.2.9 LVDS Panel Voltage Select Jumper (JP2)

DESCRIPTION

Short 1-2 +3.3 V (for 12” and 15”) Short 3-4 +5 V (for 17”, 19”, 21.5” and 24”) Short 5-6 NC

Table 6-9: LVDS Panel Voltage Select Jumper (JP2) Pinouts

6.2.10 EIDE Firmware Update Jumper (JP3)

DESCRIPTION

1 EDID_WP 2 GND

Table 6-10: EIDE Firmware Update Jumper (JP3) Pinouts

Page 73

6.3 A V-60381 AD Board

The connector locations of the AV-60381 are shown in Figure 6-1. The Pin 1 locations of

the on-board connectors are also indicated in the diagrams below. The connector pinouts

for these connectors are listed in the following sections.

DM-F Series Monitor

Figure 6-2: AV-60381 AD Board Layout Diagram

6.3.1 AV-60381 Peripheral Interface Connectors

5Table 6-11 shows a list of the peripheral interface connectors on the AV-60381 AD board.

Pinouts of the connectors that are used in the DM-F series can be found in the following

sections.

Connector Type Label

Auto dimming connector 6-pin wafer, p=1.25 mm CN4

Backlight Inverter connector 6-pin wafer, p=2.00 mm INVERTER1

COM debug port connector 2-pin wafer, p=2.00 mm CN2

LVDS connector 30-pin crimp, p=1.25 mm LVDS1

OSD keypad connector 12-pin wafer, p=1.00 mm KEYPAD1

Page 74

DM-F Series Monitor

Power input connector 3-pin wafer, p=3.96 mm PWR2

Power input connector (+12 V) 2-pin wafer, p=2.00 mm CN15

Power output connector 2-pin wafer, p=2.00 mm CN16

RS-232 connector for touchscreen 6-pin wafer, p=1.25 mm RS232_1

SPI flash connector 6-pin wafer, p=1.25 mm JSPI1

USB connector for touchscreen 4-pin wafer, p=1.25 mm USB_TOUCH1

Touchscreen connector 9-pin wafer, p=1.25 mm J1

VGA connector 10-pin box header, p=2.00 mm VGA2

Jumper Type Label

Backlight voltage select jumper 6-pin header, p=2.54 mm JP5

LVDS panel voltage select jumper 6-pin header, p=2.54 mm JP2

Power input setting jumper 6-pin header, p=2.54 mm JP4

Touchscreen type select jumper 2-pin header, p=2.00 mm JP1

Table 6-11: AV-60381 Peripheral Interface Connectors

6.3.2 Backlight Inverter Connector (INVERTER1)

PIN NO. DESCRIPTION

1 BKL_POWER1 2 BKL_POWER1 3 ENABKL 4 BRIGHTNESS 5 GND 6 GND

Table 6-12: Backlight Inverter Connector (INVERTER1) Pinouts

Page 75

6.3.3 LVDS Connector (LVDS1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 GND 2 GND 3 A0P_C 4 A0M_C 5 A1P_C 6 A1M_C 7 A2P_C 8 A2M_C 9 CLK1P_C 10 CLK1M_C 11 A3P_C 12 A3M_C 13 GND 14 GND 15 A4P_C 16 A4M_C 17 A5P_C 18 A5M_C 19 A6P_C 20 A6M_C 21 CLK2P_C 22 CLK2M_C

DM-F Series Monitor

23 A7P_C 24 A7M_C 25 GND 26 GND 27 VCC 28 VCC 29 VCC 30 VCC

Table 6-13: LVDS Connector (LVDS1) Pinouts

6.3.4 OSD Keypad Connector (KEYPAD1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 +5V_OSD(NC) 2 +12V(NC)

3 Left 4 Auto 5 Right 6 Power 7 Menu 8 Led_GREED (UP) 9 Down (NC) 10 Led_RED 11 GND 12 +3.3V_DVDD(NC)

Table 6-14: OSD Keypad Connector (KEYPAD1) Pinouts

Page 76

DM-F Series Monitor

6.3.5 Power Input Connector (PWR2)

PIN NO. DESCRIPTION

1 +9 V ~ +36 V to external power module 2 GND 3 +12 V input

Table 6-15: Power Input Connector (PWR2) Pinouts

6.3.6 RS-232 Connector for Touchscreen (RS232_1)

PIN NO. DESCRIPTION

1 NDSR 2 NRX 3 NRTS 4 NTX 5 NDTR 6 GND

Table 6-16: RS-232 Connector for Touchscreen (RS232_1) Pinouts

6.3.7 USB Connector for Touchscreen (USB_TOUCH1)

PIN NO. DESCRIPTION

1 VCC_TOUCH 2 D2F3 D2F+ 4 GND

Table 6-17: USB Connector for Touchscreen (USB_TOUCH1) Pinouts

6.3.8 Touchscreen Connector (J1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 X+ 2 X-

3 Y+ 4 SENSE 5 X+ 6 X-

Page 77

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

7 Y+ 8 Y+ 9 GND

Table 6-18: Touchscreen Connector (J1) Pinouts

6.3.9 VGA Connector (VGA2)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 RED 2 SMCLK

3 GREEN 4 SMDATA 5 BLUE 6 GND 7 H-SYNC 8 GND 9 V-SYNC 10 GND

Table 6-19: VGA Connector (VGA2) Pinouts

DM-F Series Monitor

6.3.10 Backlight Voltage Select Jumper (JP5)

DESCRIPTION

Short 1-2 +3.3 V Short 3-4 +5 V Short 5-6 +12 V

Table 6-20: Backlight Voltage Select Jumper (JP5) Pinouts

6.3.11 LVDS Panel Voltage Select Jumper (JP2)

DESCRIPTION

Short 1-2 +3.3 V (for 6.5” and 8”) Short 3-4 +5 V Short 5-6 NC

Table 6-21: LVDS Panel Voltage Select Jumper (JP2) Pinouts

Page 78

DM-F Series Monitor

6.3.12 Power Input Setting Jumper (JP4)

DESCRIPTION

Short 1-3, 2-4 +12 V from power jack (PRW1)

Short 3-5, 4-6

Input with external connector (external power module is needed)

Table 6-22: Power Input Setting Jumper (JP4) Pinouts

6.3.13 Touchscreen Type Select Jumper (JP1)

DESCRIPTION

1 5-wire touchscreen 2 4-wire/8-wire touchscreen

Table 6-23: Touchscreen Type Select Jumper (JP1) Pinouts

Page 79

DM-F Series Monitor

Appendix

A Regulatory Compliance

Page 80

DM-F Series Monitor

DECLARATION OF CONFORMITY

This equipment has been tested and found to comply with specifications for CE marking.

If the user modifies and/or installs other devices in the equipment, the CE conformity

declaration may no longer apply.

FCC WARNING

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Page 81

DM-F Series Monitor

Appendix

B Safety Precautions

Page 82

DM-F Series Monitor

WARNING:

The precautions outlined in this chapter should be strictly followed.

Failure to follow these precautions may result in permanent damage to

the DM-F Series.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the DM-F

Series is opened.

 Make sure the power is turned off and the power cord is disco nnected

whenever the DM-F Series is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock.

 Electric shocks can occur if the DM-F Series chassis is opened when the

DM-F Series is running.

 Do not drop or insert any objects into the ventilation openings of the DM-F

Series.

 If considerable amounts of dust, water, or fluids enter the DM-F Series,

turn off the power supply immediately, unplug the power cord, and contact the

DM-F Series vendor.

 DO NOT:

o Drop the DM-F Series against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature

Page 83

B.1.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the DM-F

Series may result in permanent damage to the DM-F Series and severe

injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the DM-F Series. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the DM-F Series is opened and any of the electrical components are

handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

DM-F Series Monitor

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component, touch any

grounded conducting material. During the time the electrical component is

handled, frequently touch any conducting materials that are connected to the

ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an antic-static pad. This reduces the possibility of ESD

damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical component by its edges.

Page 84

IEI Technology DM-F08A/R-R10, DM-F15A/PC-R10, DM-F12A/R-R10, DM-F12A/PC-R10, DM-F17A/R-R10 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 Overview

1.2 Features

1.3 Model Variations

1.4 Applications

1.5 Front View

1.6 Rear View

1.7 Connectors

1.7.1 DM-F65A and DM-F08A Connectors

1.7.2 DM-F12A ~ DM-F19A Connectors

1.7.3 DM-F22A and DM-F24A Connectors

1.8 Technical Specifications

1.9 Physical Dimensions

1.9.1 DM-F65A Physical Dimensions

1.9.2 DM-F08A Physical Dimensions

1.9.3 DM-F12A Physical Dimensions

1.9.4 DM-F15A Physical Dimensions

1.9.5 DM-F17A Physical Dimensions

1.9.6 DM-F19A Physical Dimensions

1.9.7 DM-F22A Physical Dimensions

1.9.8 DM-F24A Physical Dimensions

2 Unpacking

2.1 Unpacking Procedure

2.2 Packing List

2.3 Optional Items

3 Installation

3.1 Installation Precautions

3.2 External Peripheral Device Connection

3.2.1 DC-in Jack

3.2.2 9 V–36 V Terminal Block (Optional)

3.2.3 USB for Touch Panel Connector

3.2.4 VGA Connector

3.2.5 DVI-D Connector (F65A, F08A and F19A Only)

3.2.6 DisplayPort Connector (F12A ~ F24A Only)

3.2.7 HDMI Connector (F12A, F15A, F17A, F22A and F24A Only)

3.2.8 RS-232 Port for Touch Panel (Reserved for Resistive Touch)

3.2.8.1 Installing RS-232 Connector

3.3 Mounting the Monitor

3.3.1 Panel Mounting

3.3.2 Cabinet and Rack Installation (for F65A ~ F17A)

3.3.3 Cabinet and Rack Installation (for F19A)

3.3.4 Wall Mounting

3.3.5 Stand Installation

3.3.6 Arm Installation

4.1 OSD Keypad

4.2 OSD Menu Structure

4.3 Using the OSD

4.3.1 Image Menu

4.3.1.1 Color Setting

4.3.2 Display Menu

4.3.3 System Menu

4.3.3.1 Input

4.3.3.2 OSD Settings

5 Software Drivers

5.1 Introduction

5.2 RS-232 or USB Touchscreen

5.3 Touch Panel Driver Installation

5.4 Change the Touchscreen Interface

5.5 Calibrating the Touchscreen

6 AD Boards

6.1 AD Board Overview

6.2 A V-6038 AD Board

6.2.1 AV-6038 Peripheral Interface Connectors

6.2.2 Backlight Inverter Connector (INVERTER1)

6.2.3 LVDS Connector (LVDS1)

6.2.4 OSD Keypad Connector (CN14)

6.2.5 Power Input Connector (CN9)

6.2.6 RS-232 Connector for Touchscreen (RS232_1)

6.2.7 USB Connector for Touchscreen (USB_TOUCH1)

6.2.8 Touchscreen Connector (J1)

6.2.9 LVDS Panel Voltage Select Jumper (JP2)

6.2.10 EIDE Firmware Update Jumper (JP3)

6.3 A V-60381 AD Board

6.3.1 AV-60381 Peripheral Interface Connectors

6.3.2 Backlight Inverter Connector (INVERTER1)

6.3.3 LVDS Connector (LVDS1)