IEI Technology DM-F12A/R-R10, DM-F12A/PC-R10, DM-F15A/R-R10, DM-F15A/PC-R10, DM-F17A/R-R10 User Manual
...
DM-F Series Monitor
Page I
User Manual
DM Series Industrial Monitor
MODEL:
DM-F Series
12”~24” LCD Monitor
DisplayPort/HDMI/VGA, IP 65 Protection, RoHS
Rev. 1.00 – 25 March , 2014
DM-F Series Monitor
Page II
Revision
Date Version Changes
25 March, 2014 1.00 Initial Release
DM-F Series Monitor
Page III
Copyright
COP YRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliabilit y, design and functi on and d oes not r epresent a com mitm ent on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, e lectronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered tradem ark s and produc t nam es ment ioned here in are us ed for identif icatio n
purposes only and m ay be trademarks and/or registe red trademarks of their respective
owners.
DM-F Series Monitor
Page IV
Table of Contents
1 INTRODUCTION ........................................................................................................... 1
1.1 OVERVIEW ................................................................................................................... 2
1.2 FEATURES ................................................................................................................... 2
1.3 MODEL VARIATIONS ..................................................................................................... 3
1.4 APPLICATIONS ............................................................................................................. 3
1.5 EXTERNAL OVERVIEW .................................................................................................. 4
1.5.1 Front View .......................................................................................................... 4
1.5.2 Rear Vie w ........................................................................................................... 5
1.5.3 Connectors ......................................................................................................... 5
1.6 TECHNICAL SPECIFICATIONS ........................................................................................ 7
1.7 CERTIFICATIONS .......................................................................................................... 8
1.8 PHYSICAL DIMENSIONS ................................................................................................ 9
1.8.1 DM-F12A Physical Dimensions ......................................................................... 9
1.8.2 DM-F15A Physical Dimensions ....................................................................... 10
1.8.3 DM-F17A Physical Dimensions ........................................................................ 11
1.8.4 DM-F22A Physical Dimensions ....................................................................... 12
1.8.5 DM-F24A Physical Dimensions ....................................................................... 13
2 UNPACKING ................................................................................................................ 14
2.1 UNPACKING PROCEDURE ........................................................................................... 15
2.2 PACKING LIST ............................................................................................................ 16
2.3 OPTIONAL ITEMS ....................................................................................................... 17
3 AD BOARD ................................................................................................................... 18
3.1 AD BOARD OVERVIEW ............................................................................................... 19
3.2 AV-6038 AD BOARD OVERVIEW ................................................................................ 19
3.2.1 AV-6038 Peripheral Interface Connectors ....................................................... 19
3.2.2 AV-6038 Rear Panel Connectors ..................................................................... 20
4 INSTALLATION ........................................................................................................... 22
4.1 INSTALLATION PRECAUTIONS ..................................................................................... 23
DM-F Series Monitor
Page V
4.2 PRE-INSTALLATION PREPARATION ............................................................................... 24
4.2.1 Tools ................................................................................................................. 24
4.2.2 Voltage Select Jumper Settings ........................................................................ 24
4.3 EXTERNAL PERIPHERAL DEVICE CONNECTION ........................................................... 25
4.3.1 DisplayPort Connector .................................................................................... 26
4.3.2 9V-36V Terminal Block .................................................................................... 26
4.3.3 9V-36V DC Jack ............................................................................................... 27
4.3.4 HDMI Connector ............................................................................................. 27
4.3.5 RS-232 for Touch Panel Connector (Reserved for resistive touch ATO) ......... 28
4.3.6 USB for Touch Panel Connector ...................................................................... 28
4.3.7 VGA Connector ................................................................................................ 29
4.4 MOUNTING THE MONITOR ......................................................................................... 29
4.4.1 Panel Mounting ................................................................................................ 30
4.4.2 Cabinet and Rack Installation ......................................................................... 32
4.4.3 Wall Mounting .................................................................................................. 35
4.4.4 Monitor Stand Installation ............................................................................... 37
4.4.5 Monitor Arm Installation ................................................................................. 38
5 ON-SCREEN-DISPLAY (OSD) CONTROLS ............................................................. 40
5.1 USER MODE OSD STRUCTURE .................................................................................. 41
5.1.1 OSD Keypad ..................................................................................................... 41
5.1.2 OSD Menu Structure ........................................................................................ 42
5.2 USING THE OSD ........................................................................................................ 43
5.2.1 Image Menu ..................................................................................................... 43
5.2.1.1 Color Setting ............................................................................................. 44
5.2.2 Display Menu ................................................................................................... 44
5.2.3 System Menu .................................................................................................... 45
5.2.3.1 Input .......................................................................................................... 46
5.2.3.2 OSD Settings ............................................................................................. 48
6 SOFTWARE DRIVERS ................................................................................................ 49
6.1 INTRODUCTION ......................................................................................................... 50
6.2 RS-232 OR USB TOUCH SCREEN ............................................................................... 50
6.3 TOUCH PANEL DRIVER INSTALLATION ......................................................................... 51
6.4 CHANGE THE TOUCH SCREEN INTERFACE ................................................................... 55
DM-F Series Monitor
Page VI
6.5 CALIBRATING THE TOUCH SCREEN ............................................................................. 55
A SAFETY PRECAUTIONS ........................................................................................... 58
A.1 SAFETY PRECAUTIONS ............................................................................................... 59
A.1.1 General Safety Precautions ............................................................................. 59
A.1.2 Anti-static Precautions .................................................................................... 60
A.2 MAINTENANCE AND CLEANING PRECAUTIONS ............................................................ 60
A.2.1 Maintenance and Cleaning .............................................................................. 60
A.2.2 Cleaning T ools ................................................................................................. 61
B CERTIFICATIONS ...................................................................................................... 62
B.1 ROHS COMPLIANT .................................................................................................... 63
B.2 IP 65 COMPLIANT FRONT PANEL ............................................................................... 63
C SMARTOSD .................................................................................................................. 64
C.1 IEI SMARTOSD QUICK INSTALLATION GUIDE ............................................................ 65
C.2 PRE-INSTALLATION NOTICE ....................................................................................... 65
C.3 SMARTOSD INSTALL .................................................................................................. 65
C.4 SOFTWARE ILLUSTRATION .......................................................................................... 68
C.4.1 Manage Page ................................................................................................... 71
C.4.2 EDID Page ...................................................................................................... 72
C.4.3 Image Page ...................................................................................................... 73
C.4.4 Display Page (for analog signal) .................................................................... 74
C.4.5 Color Page ...................................................................................................... 75
C.4.6 PIP Page .......................................................................................................... 76
C.4.7 System Page ..................................................................................................... 77
C.4.8 About Page ...................................................................................................... 78
C.5 SMARTOSD FAQ ...................................................................................................... 79
C.5.1 Windows 2000 Installation Failure ................................................................. 79
C.5.2 V ista Installation Failure ................................................................................. 79
C.5.3 Model Failure .................................................................................................. 80
C.5.4 DDC Port Failure ........................................................................................... 81
DM-F Series Monitor
Page VII
List of Figures
Figure 1-1: DM-F Series ................................................................................................................. 2
Figure 1-2: Typical Monitor Front View
........................................................................................ 4
Figure 1-3: Typical Rear View
........................................................................................................ 5
Figure 1-4: Connectors (DM-F12A/15A/17A)
................................................................................ 5
Figure 1-5: Connectors (DM-F22A/24A)
........................................................................................ 6
Figure 1-6: DM-F12A Physical Dimensions (millimeters)
........................................................... 9
Figure 1-7: DM-F15A Physical Dimensions (millimeters)
.........................................................10
Figure 1-8: DM-F17A Physical Dimensions (millimeters)
.........................................................11
Figure 1-9: DM-F22A Physical Dimensions (millimeters)
.........................................................12
Figure 1-10: DM-F24A Physical Dimensions (millimeters)
.......................................................13
Figure 3-1: AV-6038 AD Board Overview
...................................................................................19
Figure 4-1: Connectors (DM-F12A/15A/17A)
..............................................................................25
Figure 4-2: Connectors (DM-F22A/24A)
......................................................................................25
Figure 4-3: DisplayPort connector
..............................................................................................26
Figure 4-4: 3-pin Terminal Block
.................................................................................................27
Figure 4-5: 9V-36V DC Jack
.........................................................................................................27
Figure 4-6: HDMI Connector
........................................................................................................28
Figure 4-7: RS-232 Touch Panel Connector
..............................................................................28
Figure 4-8: USB Touch Panel Connector
...................................................................................29
Figure 4-9: VGA Connector
.........................................................................................................29
Figure 4-10: DM-F12A Cutout Dimensions (Unit: mm)
.............................................................31
Figure 4-11: DM-F15A Cutout Dimensions (Unit: mm)
.............................................................31
Figure 4-12: DM-F17A Cutout Dimensions (Unit: mm)
.............................................................31
Figure 4-13: DM-F22A Cutout Dimensions (Unit: mm)
.............................................................31
Figure 4-14: DM-F24A Cutout Dimensions (Unit: mm)
.............................................................32
Figure 4-15: Panel Mounting Clamp Position
............................................................................32
Figure 4-16: Secure the Cabinet/Rack Bracket
..........................................................................33
Figure 4-17: Install into a Cabinet/Rack
.....................................................................................34
Figure 4-18: Wall-mounting Bracket
...........................................................................................35
Figure 4-19: Mount the Chassis
..................................................................................................36
DM-F Series Monitor
Page VIII
Figure 4-20: VESA Mounting Holes ............................................................................................37
Figure 4-21: Monitor Stand Mounting
.........................................................................................38
Figure 4-22: Monitor Arm Mounting
............................................................................................39
Figure 5-1: OSD Keypad
..............................................................................................................41
Figure 5-2: Image Menu
...............................................................................................................43
Figure 5-3: Color Settings
............................................................................................................44
Figure 5-4: Display Menu
.............................................................................................................45
Figure 5-5: System Menu
.............................................................................................................46
Figure 5-6: Input Options
.............................................................................................................47
Figure 5-7: OSD Settings Menu
...................................................................................................48
Figure 6-1: Setup Icon
..................................................................................................................52
Figure 6-2: Welcome Screen
.......................................................................................................52
Figure 6-3: License Agreement
...................................................................................................53
Figure 6-4: Initiate Install
.............................................................................................................53
Figure 6-5: Installation Starts
......................................................................................................54
Figure 6-6: Finish Installation
......................................................................................................54
Figure 6-7: PenMount Monitor Icon
............................................................................................55
Figure 6-8: PenMount Monitor Popup Menu
..............................................................................56
Figure 6-9: Configuration Screen
................................................................................................56
Figure 6-10: Calibration Initiation Screen
..................................................................................57
Figure 6-11: Calibration Screen
..................................................................................................57
Figure 6-12: smartOSD Welcome Screen
...................................................................................66
Figure 6-13: smartOSD Folder Select Screen
............................................................................66
Figure 6-14: smartOSD Confirm Installation
..............................................................................67
Figure 6-15: smartOSD Installation Progress
............................................................................67
Figure 6-16: smartOSD Installation Complete ...........................................................................68
Figure C-17: Manage Page
...........................................................................................................71
Figure C-18: EDID Page
...............................................................................................................72
Figure C-19: Image Page
..............................................................................................................73
Figure C-20: Display Page
...........................................................................................................74
Figure C-21: Color Page
...............................................................................................................75
Figure C-22: PIP Page
..................................................................................................................76
Figure C-23: System Page
...........................................................................................................77
Figure C-24: About Page
..............................................................................................................78
Figure C-25: DLL Missing
............................................................................................................79
DM-F Series Monitor
Page IX
Figure C-26: Windows Vista Error ..............................................................................................79
Figure C-27: Install as Administrator
..........................................................................................80
Figure C-28: Firmware Incompatibility
.......................................................................................80
Figure C-29: DDC Port Failure
.....................................................................................................81
DM-F Series Monitor
Page X
List of Tables
Table 1-1: DM-F Series Model Variations ..................................................................................... 3
Table 1-2: DM-F Series Sp ecificat io n s
.......................................................................................... 8
Table 2-1: Packing List
.................................................................................................................16
Table 2-2: Optional Items
.............................................................................................................17
Table 3-1: AV-6038 Peripheral Interface Connectors
................................................................20
Table 3-2: AV-6038 Rear Panel Connectors
...............................................................................21
Table 4-1: LCD Panel Voltage Select Jumper Settings
.............................................................24
Table 4-2: Display Port Connector Pinouts
...............................................................................26
Table 4-3: HDMI Connector Pinouts
...........................................................................................28
Table 4-4: RS-232 Touch Panel Connector Pinouts
..................................................................28
Table 4-5: USB Touch Panel Connector Pinouts
......................................................................29
Table 4-6: VGA Connector Pinouts
.............................................................................................29
Table 4-7: Panel Mounting Clamps
.............................................................................................30
Table 5-1: OSD Menu Structure
...................................................................................................42
Table C-1: SmartOSD Menu Structure
........................................................................................70
DM-F Series Monitor
Page 1
Chapter
1
1 Introduction
DM-F Series Monitor
Page 2
1.1 Overview
Figure 1-1: DM-F Series
The DM-F series LCD monitor is the latest member of IEI’s line of sophisticated LCD
designs, and it has been improved to b e RoHS compliant. It is designed to fit industrial
automation, or an y other applications that require minim um installat ion spac e and flexibl e
configuration. The f lat front panel provides I P 65 protection, whic h effectively w ards off
dust and water. Flexibl e analog or digital interf aces are provided for ease of connect ion
with a management computer.
1.2 Features
The DM-F series have the following standard features:
Robust IP 65 aluminum front bezel
Aesthetic ultra-thin bezel for seamless panel mount installation
Wide range 9V~36V DC input
HDMI/Display Port/VGA flexible video input solution
Projected capacitive multi-touch/ resistive single touch options
DM-F Series Monitor
Page 3
1.3 Model Variations
The DM-F series LCD monitor base models have a variety of variants. The model
variations are listed in Table 1-1.
Model Number LCD Touch Screen
DM-F12A/R-R10
12”
W/ USB resistive touch screen
DM-F12A/PC-R10 W/ USB projected capacitive touch screen
DM-F15A/R-R10
15”
W/ USB resistive touch screen
DM-F15A/PC-R10 W/ USB projected capacitive touch screen
DM-F17A/R-R10
17”
W/ USB resistive touch screen,
DM-F17A/PC-R10 W/ USB projected capacitive touch screen
DM-F22A/PC-R10 21.5” W/ USB projected capacitive touch screen
DM-F24A/PC-R10 24” W/ USB projected capacitive touch screen
Table 1-1: DM-F Series Model Variations
1.4 Applications
The DM-F series LCD m onitor is designed for rigorous industrial environments where it
may be exposed to bot h heat and moisture. Its dura bility and strength also m akes it an
ideal choice for public access computers. Some possible applications include:
Digital surveillance
Multimedia advertising platform
General Computing
o Computer-based testing center
o General purpose information system
o Mobile nursing station
o Interactive education use
Automation & Control
o Plant environment monitoring
o Factory automation HMI terminal
o Shop-floor/MES control
Self-service Kiosk
DM-F Series Monitor
Page 4
o Full-service receptionist kiosk
o Hospital self-registration terminal
o Interactive photo kiosk
o Video rental kiosk
o Self-service POS terminal
1.5 External Overview
The DM-F series LCD monitors are durable devices that can be used in harsh industrial
environments. The following sections describe the physical layout of the DM-F series LCD
monitors.
1.5.1 Front View
The front of the DM-F series LCD monitor is a flat panel LCD screen surroun ded by an
aluminum frame.
Figure 1-2 shows a typical monitor front view.
Figure 1-2: Typical Monitor Front View
DM-F Series Monitor
Page 5
1.5.2 Rear View
The rear panel provides ac cess to retention screw holes that support various mounting.
There is a 7-key membrane OSD keypad on the rear panel.
Figure 1-3 shows a typical DM-F rear panel.
Figure 1-3: Typical Rear View
1.5.3 Connectors
Figure 1-4 and Figure 1-5 shows t he bottom pane l of the DM-F series LCD monitor. All
connectors are fully described in Section 4.3.
Figure 1-4: Connectors (DM-F12A/15A/17A)
DM-F Series Monitor
Page 6
Figure 1-5: Connectors (DM-F22A/24A)
DM-F Series Monitor
Page 7
1.6 Technical Specifications
Table 1-2 shows the DM-F series technical specifications.
Model DM-F12A DM-F15A DM-F17A DM-F22A DM-F24A
LCD Display 12" (4:3) 15'' (4:3) 17'' (5:4) 21.5'' (16:9) 24'' (16:9)
Max. Resolution 1024(W) x 768(H) 1024(W) x 768(H) 1280(W) x 1024(H) 1920(W) x 1080(H) 1920(W) x 1080(H)
Brightness (cd/m²) 500 400 350 250 250
Contrast Ratio 700:1 700:1 1000:1 1000:1 3000:1
LCD Color 16.2M 16.2M 16.7M 16.7M 16.7M
Pixel Pitch (mm) 0.24 x 0.24 0.29 x 0.29 0.26 x 0.26 0.25 x 0.25 0.28 x 0.28
Viewing Angle (H/V) 160°/140° 160°/140° 170°/160° 170°/160° 178°/178°
Backlight MTBF (Hrs) 50000 50000 50000 30000 30000
Touch
Resistive type 5-wire flat touch window/ Penmount 6000
Projected capacitive flat touch window/ EETI EXC7200
Projected
capacitive
flat touch window/
EETI
EXC7200
Projected
capacitive
flat touch window/
EETI
EXC3000
AD Board AV-6038 AV-6038 AV-6038 AV-6038 AV-6038
I/O Ports
1 x VGA (DB-15)
1 x HDMI
1 x DisplayPort 1.1
1 x USB 2.0 (touch)
1 x RS-232 (touch) [reserved for resistive touch ATO]
1 x Lockable 9V-36V DC jack
1 x 9V-36V terminal block
OSD Button 7-key membrane OSD keypad
Smart OSD Smart OSD Software
Construction Material Aluminum front cover and sheet metal rear cover
Mounting Panel Mount/ Rack Mount/ 10 0*1 00 VESA Mou nt
Enclosure Color Black C
Dimension
262.2 x 322.2 x
40.5 mm
303 x 378.5 x 43.2
mm
341.4 x 408.4 x 49. 3
mm
350.4 x 550.4 x
49.1 mm
382 x 600 x 49.4
mm
Cutout Dimensions 234.8 x 303.8 mm 284.6 x 68.1 mm 323 x 398 mm 340 x 532 mm 358.6 x 578.6 mm
DM-F Series Monitor
Page 8
Model DM-F12A DM-F15A DM-F17A DM-F22A DM-F24A
Weight (Net/Gross)
Kg
2.7/4.9 3.5/5.5 4.4/7.1 6.3/9.6 7.6/10.9
Operating
Temperature
-20°C ~ 60°C (with air flow) -10°C ~ 50°C (with air flow)
Storage
Temperature
-20°C ~ 70°C -20°C ~ 60°C
Humidity 10% to 95% (non-condensing)
IP Level IP 65 compliant front panel
Safety and EMC CE & FCC certified
Power Input 9V~36V DC
Table 1-2: DM-F Series Specifications
1.7 Certifications
All DM-F series LCD monitor models comply with the following international standards:
RoHS
IP 65
For a more detailed description of these standards, please refer to Appendix B.
DM-F Series Monitor
Page 9
1.8 Phy s ical Dimensions
The following sections describe the physical dimensions for each model of the DM-F
series LCD monitor.
1.8.1 DM-F12A Phys ical Dimensions
The physical dimensions of the DM-F12A are shown in Figure 1-6.
Figure 1-6: DM-F12A Physical Dimensions (millimeters)
DM-F Series Monitor
Page 10
1.8.2 DM-F15A Phys ical Dimensions
The physical dimensions of the DM-F15A are shown in Figure 1-7.
Figure 1-7: DM-F15A Physical Dimensions (millimeters)
DM-F Series Monitor
Page 11
1.8.3 DM-F17A Phys ical Dimensions
The physical dimensions of the DM-F17A are shown in Figure 1-8.
Figure 1-8: DM-F17A Physical Dimensions (millimeters)
DM-F Series Monitor
Page 12
1.8.4 DM-F22A Phys ical Dimensions
The physical dimensions of the DM-F22A are shown in Figure 1-9.
Figure 1-9: DM-F22A Physical Dimensions (millimeters)
DM-F Series Monitor
Page 13
1.8.5 DM-F24A Phy s ical Dimens ions
The physical dimensions of the DM-F24A are shown in Figure 1-10.
Figure 1-10: DM-F24A Physical Dimensions (millimeters)
DM-F Series Monitor
Page 14
2 Unpacking
Chapter
2
DM-F Series Monitor
Page 15
2.1 Unpacking Procedure
To unpack the DM-F series LCD monitor, follow the steps below:
WARNING:
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover a fter the DM-F series LCD monitor
has been properly installed. This ensures the screen is protected during the
installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the DM-F series LCD monitor.
Step 7: Make sure all the components listed in the packing list are present. St ep 0:
DM-F Series Monitor
Page 16
2.2 Packing Lis t
The DM-F series monitor is shipped with the following components:
Quantity Ite m Image
1 DM-F series
1 USB Cable (For touch screen)
(P/N: 32001-006100-100-RS)
1 VGA Cable
(P/N: 32000-036200-RS)
1 Touch pen (Resistive touch only)
(P/N: 43125-0002C0-00-RS)
1 Utility CD (Drivers and user manual)
Table 2-1: Packing List
If any of the above items are missing or damaged, contact the distributor or sales
representative imm ediately.
DM-F Series Monitor
Page 17
2.3 Optional Ite ms
The following items are optional accessories for the DM-F series monitor:
Ite m DM-F12A DM-F15A DM-F17A DM-F22A DM-F24A
Arm ARM-11-RS ARM-31-RS
Stand
STAND-A12-RS
STAND-A19-RS
STAND-B19-RS
STAND-C19-RS
STAND-A21-R10
Wall Mount Kit WK-190MS-R10
Panel Mount Kit FPK-01-R10 FPK-02-R10 FPK-03-R10
Rack Mount Kit FRK12-R10 FRK15-R10 FRK17-R10 N/A
Cable Cover N/A DM-F-CC01-R10 DM-F-CC02-R10
RS-232 Touch
Cable Kit
DM-F-COMKIT01-R10 N/A
HDMI Cable 32012-000100-200-RS
Display Port Cable
32004-000200-100-RS
Power Adapter 63040-010060-040-RS (60W 12V DC adapter with lock)
Power cord Depends on shipping region
Table 2-2: Optional Items
DM-F Series Monitor
Page 18
Chapter
2
3 AD Board
DM-F Series Monitor
Page 19
3.1 AD Board Overview
The DM-F series LCD monitor AD board provides a wide variety of control interfaces,
receiving and managing i nterf ace s ignals fr om a CPU card through cabling . The following
sections describe each AD board in detai l.
3.2 AV-6038 AD Boar d Overview
The AV-6038 AD board provides a wide variety of control interfaces, receiving and
managing interface signals from a CPU card through cabling. The following sections
describe the AV-6038 AD board in detail.
Figure 3-1: AV-6038 AD Board Overview
3.2.1 AV-6038 Peripheral Interface Connectors
Table 3-1 shows a list of the peripheral interface connectors on the AV-6038 AD board.
DM-F Series Monitor
Page 20
Connector Type Label
Audio speaker output connector 4-pin wafer connector Audio_LOUT1
Audio speaker output connector 4-pin wafer connector Audio_ROUT1
RS-232 input connector 6-pin wafer connector RS232_1
Power input connector 4-pin connector CN9
Touch screen connector 9-pin wafer connector J1
External OSD connector 12-pin wafer connector CN14
LVDS connector 30-pin connector LVDS1
Backlight Inverter connector 6-pin wafer connector INVERTER1
Webcam USB connector 4-pin wafer connector USB_CAM1
USB for touch screen connector 4-pin wafer connector USB_TOUCH1
Infrared connector 3-pin wafer connector CN3
COM debug connector 4-pin wafer connector CN2
SPI ROM connector 6-pin wafer connector JSPI1
Display port EDID connector 4-pin wafer connector DP_FW1
HDMI EDID connector 4-pin wafer connector HDMI1_FW1
Table 3-1: AV-6038 Peripheral Interface Connectors
3.2.2 AV-6038 Rear Panel Connectors
Table 3-2 lists the rear panel connectors on the AV-6038 AD board.
Connector Type Label
Display port connector DisplayPort 1.1 DISPLAY_PORT1
HDMI connector HDMI type A connector HDMI1
Power input connector DC Power Jack CN8
DM-F Series Monitor
Page 21
USB connector USB 2.0 USB1
VGA connector 15-pin VGA connector VGA1
Table 3-2: AV-6038 Rear Panel Connectors
DM-F Series Monitor
Page 22
Chapter
3
4 Ins tallation
DM-F Series Monitor
Page 23
4.1 Ins tallation Precautions
When installing the DM-F series LCD monitor, please follow the precautions listed below:
Read the user manual: The user manual provides a complete description of
the DM-F series LCD monitor, installation instructions and configuration
options.
DANGER! Disconnect Power: Power to the monitor must be disconnected
when installing the DM-F series LCD monitor, or before any attempt is made
to access the rear panel. Electric shock and personal injury might occur if the
rear panel of the monitor is opened while the power cord is still connected to
an electrical outlet.
Qualified Personnel: The DM-F series LCD monitor must be installed and
operated only by trained and qualif ied pers onn el. Ma intenanc e , upgrades, or
repairs may only be carried out by qualified personnel who are familiar with
the associated dangers.
Mounting: Since the monitor may weigh up to 10 kg (not including a swing
arm or other accessories), please ensure at least two people ass ist with
mounting the monitor.
Air Circulation: Make sure there is sufficient air circulation when installing the
monitor. The monitor’s cooling vents must not be obstructed by any objects.
Blocking the vents can cause overheating of the monitor. Leave at least 5 cm
of clearance around the monitor to prevent overheating.
Grounding: The monitor should be properly grounded. The voltage feeds
must not be overloaded. Adjust the cabling and provide external overcharge
protection per the electrical values indicated on the label attached to the back
of the monitor.
Anti-static Discharge: The rear panel of the monitor must to be removed to
configure the monitor’s AD board voltage select jumper. When doing so, be
sure the monitor is disconnected from its power source and take all necessary
safety precautions to avoid electrocution and static discharge to the AD board.
The use of a grounded wrist strap and an anti-static work pad is
recommended.
DM-F Series Monitor
Page 24
4.2 Pre-inst allation Prepar at ion
4.2.1 Tools
Before installing the DM-F series LCD monitor, make sure the following tools are on hand:
Philips (crosshead) screwdriver: All the retention screws on the system are
Philips screws.
Soft working mat: When the DM-F series LCD monitor is installed, the
screen is placed on the working surface. It is therefore important to rest the
MPC industrial workstation on a soft at that cannot damage the LCD screen
on the front of the DM-F series LCD monitor.
4.2.2 Voltage Select Jumper Settings
The voltage select jum per on the integrated AD board mus t be configured to select the
input voltage required to po w er the monitor. Refer to Table 4-1 for the appropriate j um per
settings of the AD board.
JP2 Des cription
1-2 DM-F12A, DM-F15A
3-4 DM-F17A, DM-F22A, DM-F24A
5-6 NC
Table 4-1: LCD Panel Voltage Select Jumper Settings
To properly set the voltage select jumper, the following steps must be completed:
Step 1: Use a screwdriver to remove all the screws holding the rear panel to the monitor.
Step 2: Remove the rear panel.
Step 3: Locate the voltage select jumper. (See Figure 3-1)
Step 4: Use the jumper(s) to set the correct voltage input. (See Table 4-1)
Step 5: Replace the rear panel.
Step 6: Replace all removed screws.S tep 0:
DM-F Series Monitor
Page 25
4.3 External Peripheral Device Connection
The external periphera l i nte rface panel connectors f or t he DM-F series industri al monitors
are listed below.
1 x DisplayPort 1.1
1 x 9V-36V terminal block
1 x Lockable 9V-36V DC jack
1 x HDMI
1 x RS-232 (reserved for resistive touch ATO)
1 x USB 2.0 for touch screen
1 x VGA
Figure 4-1 and Figure 4-2 shows the E PIC panel connectors for the DM-F series LCD
monitor. The following sections fully describe EPIC panel connectors.
Figure 4-1: Connectors (DM-F12A/15A/17A)
Figure 4-2: Connectors (DM-F22A/24A)
DM-F Series Monitor
Page 26
4.3.1 DisplayPort Connector
The DisplayPort connector transmits a digital signal to compatible DisplayPort display
devices such as a TV or computer screen.
PIN DESCRIPTION PIN DESCRIPTION
1 ML_L3N 2 GND
3 ML_L3P 4 ML_L2N
5 GND 6 ML_L2P
7 ML_L1N 8 GND
9 ML_L1P 10 ML_L0N
11 GND 12 ML_L0P
13 GND 14 GND
15 C_DDI0_DP_AUXP 16 GND
17 C_DDI0_DP_AUXN 18 C_DDI0_DP_HPD
19 GND 20 VCC
21 GND 22 GND
23 GND 24 GND
Table 4-2: Display Port Connector Pinouts
Figure 4-3: DisplayPort connector
4.3.2 9V-36V Terminal Block
Connect the leads of 9V-36V DC po w er s upp l y into the t erm inal b lock. Make sure that the
power and ground wires are attached to the correct sockets of the connector.
DM-F Series Monitor
Page 27
Figure 4-4: 3-pin Terminal Block
4.3.3 9V-36V DC Jack
The power connector connects to the 9V-36V DC power adapter.
Figure 4-5: 9V-36V DC Jack
4.3.4 HDMI Connector
The HDMI connector con ne cts to a display device wit h H DMI interface.
PIN DESCRIPTION PIN DESCRIPTION
1 HDMI_TMDS_C_DATA2 2 GND
3 HDMI_TMDS_C_DATA2# 4 HDMI_TMDS_C_DATA1
5 GND 6 HDMI_TMDS_C_DATA1#
7 HDMI_TMDS_C_DATA0 8 GND
9 HDMI_TMDS_C_DATA0# 10 HDMI_TMDS_C_CLK
11 GND 12 HDMI_TMDS_C_CLK#
13 NC 14 NC
15 HDMI_DDC_SCLK 16 HDMI_DDC_SDATA
17 GND 18 +5V_HDMI
19 HDMI_HPD
DM-F Series Monitor
Page 28
PIN DESCRIPTION PIN DESCRIPTION
Table 4-3: HDMI Connector Pinouts
Figure 4-6: HDMI Connector
4.3.5 RS-232 for Touch Panel Connector (Reserved for resistive touch
ATO)
Use the rear panel standard RS-232 DB-9 female touch pane l connector to connec t the
monitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
1 N/A 6 NDSR
2 NRX 7 NRTS
3 NTX 8 N/A
4 NDTR 9 N/A
5 GND
Table 4-4: RS-232 Touch Panel Connector Pinouts
Figure 4-7: RS-232 Touch Panel Connector
4.3.6 USB for Touch Panel Connector
Use the rear panel standard USB touch pane l connector to connec t the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
DM-F Series Monitor
Page 29
1 VCC 2 USB20_N11
3 USB20_P11 4 GND
Table 4-5: USB Touch Panel Connector Pinouts
Figure 4-8: USB Touch Panel Connector
4.3.7 VGA Connector
Use the rear pane l standard 15-pin female VGA connector to connect t he monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION
1 RED 6 GROUND 11 NC
2 GREEN 7 GROUND 12 DDCDAT
3 BLUE 8 GROUND 13 HSYNC
4 NC 9 NC 14 VSYNC
5 GROUND 10 GROUND 15 DDCCLK
Table 4-6: VGA Connector Pino u ts
Figure 4-9: VGA Connector
4.4 Mounting the Monitor
The DM-F series LCD monitor can be mounted in a panel, cabinet, rack or wall. The
monitor can also be mounted on a monitor arm or stand. The mounting methods are
described below.
CAUTION:
DM-F Series Monitor
Page 30
When mounting th e monitor take care t o tighten the retentio n screws or bolts
until fully secure, but do no t over tighten. Over ti ghtening the retentio n screws
or bolts may cause them to become stripped, rendering them useless.
4.4.1 Panel Mounting
Each model of the DM-F series LCD monitor has a series of mounting slots located on the
top and bottom panel for mounting the monitor to a panel.
Table 4-7 lists the number of mounting clamps required to mount the monitor to a panel.
Model Mounting Clamps
DM-F12A 9
DM-F15A 9
DM-F17A 9
DM-F22A 10
DM-F24A 12
Table 4-7: Panel Mounting Clamps
To mount the DM-F series LCD monitor into a panel, please follow the steps below.
Step 1: Select the position on the panel to mount the monitor.
Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of
the monitor. Take care that the panel section that is cut out is smaller than the
overall size of the metal frame that surrounds the monitor but just large enough
for the rear panel of the monitor to fit through.
DM-F Series Monitor
Page 31
Figure 4-10: DM-F12A Cutout Dimensions (Unit: mm)
Figure 4-11: DM-F15A Cutout Dimensions (Unit: mm)
Figure 4-12: DM-F17A Cutout Dimensions (Unit: mm)
Figure 4-13: DM-F22A Cutout Dimensions (Unit: mm)
DM-F Series Monitor
Page 32
Figure 4-14: DM-F24A Cutout Dimensions (Unit: mm)
Step 3: Slide the monitor through the hole until the aluminum frame is flush against the
panel.
Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of
the monitor, behind the metal frame. Refer to the mounting kit packing list for the
required number of mounting clamps.
Figure 4-15: Panel Mounting Clamp Position
Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic
caps at the front of all the screws are firmly secured to the panel (Figure 4-15).
4.4.2 Cabinet and Rack Ins tallation
To mount the DM-F series LCD monitor into a cabinet/rack, please follow the steps below.
DM-F Series Monitor
Page 33
Step 1: The back of the metal frame surrounding the DM-F series LCD monitor has
several retention screw holes for a cabinet/rack installation bracket.
NOTE:
When purchasing a cabinet/rack installation bracke
t, make sure it is
compatible with both the monitor and the cabinet/rack into which the
monitor is installed.
Step 2: Slide the monitor through the cabinet/rack bracket until the rear side of the
monitor frame is flush against the front of the bracket.
Step 3: Make sure the retention screw holes at the rear of the monitor frame are aligned
with the retention screw holes in the cabinet/rack bracket.
Step 4: Secure the cabinet/rack bracket to the monitor by inserting and tightening the
retention screws (Figure 4-16).
Figure 4-16: Secure the Cabinet/Rack Bracket
DM-F Series Monitor
Page 34
Step 5: Slide the monitor with the attached cabinet/rack bracket into a rack or cabinet
(Figure 4-17).
Figure 4-17: Install into a Cabinet/Rack
Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into
the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the
rack or cabinet (Figure 4-17).
DM-F Series Monitor
Page 35
4.4.3 Wall Mounting
CAUTION:
Due to safety conc erns, it is highly r ecommended to use the VESA mounti ng
kits provided by IEI for w all, s tand and ar m moun ting. If the VESA m ountin g kit
is purchased separately, please make sure the mounting kit is UL-listed.
Each model of the DM-F series LCD monitor has four holes located o n the rear panel f or
mounting the monitor to a wall. To mount the DM-F series LCD monitor onto a wall , ple ase
follow the steps below.
Step 1: Select a location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four bracket screw holes on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into
the four pilot holes and tightening them (Figure 4-18).
Figure 4-18: Wall-mounting Bracket
DM-F Series Monitor
Page 36
Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the
four screw holes on the real panel of the monitor and tighten until the screw
shank is secured against the rear panel (Figure 4-19).
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes (Figure 4-19).
Ensure that all four of the mounting screws fit snuggly into their respective
slotted holes.
NOTE:
In the diagram below the bracket is already installed on the wall.
Figure 4-19: Mount the Chassis
DM-F Series Monitor
Page 37
4.4.4 Monitor Stand Installation
The DM-F series LCD monitor has Video Electronics Standards Association (VESA)
standard mounting holes tapped into the rear panel. The standard holes are M4 set at
100m x 100mm apart (Figure 4-20).
Figure 4-20: VESA Mounting Holes
The monitor stand mounting plate has a matching VESA hole pattern. To mount the DM-F
series LCD monitor onto a stand, please follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor stand mounting plate.
Step 2: Secure the monitor to the stand with the supplied retention screws (Figure
4-21).
DM-F Series Monitor
Page 38
Figure 4-21: Monitor Stand Mounting
4.4.5 Monitor Arm Ins tallation
The DM-F series LCD monitor has Video Electronics Standards Association (VESA)
standard mounting holes t apped into the rear panel. The standard holes ar e M4 set at
100m x 100mm apart (Figure 4-20). The monitor arm mounting plate has a matching
VESA hole pattern. T o mount the DM-F series LCD m onitor onto a monitor arm, please
follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor arm mounting plate.
Step 2: Secure the monitor to the arm with the supplied retention screws (Figure 4-22).
Step 0:
DM-F Series Monitor
Page 39
Figure 4-22: Monitor Arm Mounting
DM-F Series Monitor
Page 40
Chapter
4
5 On-Screen-Display (OSD)
Controls
DM-F Series Monitor
Page 41
5.1 User Mode OSD Structure
5.1.1 OSD Keypad
There are several on-screen-display (OSD) control buttons of the OSD keypad on the
monitor rear panel. Figure 5-1 shows the 7-key membrane OSD keypad of the DM-F
series LCD monitor.
Figure 5-1: OSD Keypad
DM-F Series Monitor
Page 42
5.1.2 OSD Menu Structure
Table 5-1 shows the OSD menu structure for all models of the DM-F series LCD monitor.
Level 0 Level 1 Level 2 Value
Image Brightness 0 to 100
Contrast 0 to 100
Sharpness -4 to 4
Color Auto
Color temp 5000K
6500K
9300K
User
Reset
Display Auto Adjust
Phase 0 to 100
Clock 0 to 100
Display Position
Display Modes Gamma off
Gamma 2.2
System Input Display Port
VGA
DVI/HDMI
autoscan
OSD Setting Timer 10sec/30sec/60sec
Rotation
0°/90°/180°/270°
Position
Transparency 0 to 100
Information
Reset
Table 5-1: OSD Menu Structure
DM-F Series Monitor
Page 43
5.2 Us ing the OSD
OSD menu options are described below.
5.2.1 Image Menu
Image menu features are shown in Figure 5-2.
Figure 5-2: Image Menu
Brightness
The brightness opt ion adjusts the brightnes s of screen. This functi on
adjusts the offset value of ADC. S
etting this valu e too high or to o low
will affect the quality of image. When the auto-
dimming function is
turned on, the brightness control is not effective.
Contrast
This function adjusts the g ain value of ADC. A
djusting this value too
high or too low will worsen the quality of image.
Sharpness
Adjusts the
sharpness level. This option softens the edges around
objects on the screen.
Color Provides options for color settings. (Figure 5-3)
DM-F Series Monitor
Page 44
5.2.1.1 Color Setting
Color settings are shown in Figure 5-2.
Figure 5-3: Color Settings
auto
Automatically adjusts the color settings.
Color temp
This item allows adjustment of the following items.
5000k – NTSC standard Kelvin
6500k – NTSC standard Kelvin
9300k – NTSC standard Kelvin
User – This item allows fine-tuning t he ba lance among Red,
Green, and Blue color hues if images look garish or unrealistic.
5.2.2 Display Me n u
Display menu features ar e s ho wn in Figure 5-4.
DM-F Series Monitor
Page 45
Figure 5-4: Display Menu
Auto Adjust
Automatically adjusts the LCD screen position.
Phase
Adjusts the input signal (Analog only)
Clock
Adjusts the dot clock position
Display Position
Adjusts the horizontal and vertical position of the display screen
Display Mode
This item allows adjustment of the Gamma.
5.2.3 System Me n u
System menu featur es are s ho wn in Figure 5-5.
DM-F Series Monitor
Page 46
Figure 5-5: System Menu
Input Allows selection of input device to use. (Figure 5-6)
OSD Settings Provides options for OSD configuration. (Figure 5-7)
Information
Provides inform ation on the LCD monitor, such as firmware
version,
release date and input resolution.
Reset
Restores the default OSD settings. Note that this will restore all default
display settings.
5.2.3.1 Input
Input options are shown in Figure 5-6.
DM-F Series Monitor
Page 47
Figure 5-6: Input Options
Input options are described below.
Display Port
This item sets the input device to display port.
VGA
This item sets the input device to VGA.
DVI/HDMI
This item sets the input device to DVI/HDMI.
autoscan
Selects the input device to use automatically.
DM-F Series Monitor
Page 48
5.2.3.2 OSD Settings
The OSD settings are shown in Figure 5-7.
Figure 5-7: OSD Settings Menu
OSD settings are described below.
Timer
Determines how many seconds the
OSD screen stays on screen
before it disappears when OSD is left unattended.
Rotation
Adjusts the OSD rotation angle on the screen.
Position
Adjusts the OSD position on the screen.
Transparency
Adjust the transparency of the OSD menu background.
DM-F Series Monitor
Page 49
Chapter
5
6 Software Drivers
DM-F Series Monitor
Page 50
6.1 Introduction
The touch panel contro ller enables ana log res istive t ouc h panels f or f our-wire, five-wire &
eight-wire models. The c ontroller directl y communicates with the PC system through the
touch panel communications interface. The controller design is superior in sensitivity,
accuracy, and friendl y operation. The touch pa nel driver emulates the left mouse butt on
and the right mouse bu tton functions.
The touch panel driver supports the following operating systems:
Microsoft
®
Windows® versions:
o Microsoft
®
Windows® 2000
o Microsoft
®
Windows® XP
o Microsoft
®
Windows® 2003
o Microsoft
®
Windows® 2008
o Microsoft
®
Windows® Vista
o Microsoft
®
Windows® 7
o Microsoft
®
Windows® 8
Microsoft
®
Windows® CE versions:
o Microsoft
®
Windows® CE 4.2
o Microsoft
®
Windows® CE 5.0
o Microsoft
®
Windows® CE 6.0
Linux Kernel 2.6
DOS
Driver installation is described below.
6.2 RS-232 or USB Touch Screen
Before installing the driver, connect the DM-F series monitor to the motherboard. The
DM-F series monitors s upp ort touch s c reen modality through an R S-232 or USB interface
connection. Decide through which interface the touch screen is to be controlled.
NOTE:
DM-F Series Monitor
Page 51
The default touch screen interface for the DM-F series monitor is USB interface.
The RS-232 interface is only reserved for resistive touch ATO
RS-232 Interface: If the touch screen interface connection is an RS-232
connection, connect the RS-232 connector on the single board computer to
the DB-9 connector of the DM-F series monitor.
USB Interface: If the touch screen interface connection is a USB connection,
connect the USB connector on the single board computer to the external USB
port connector of the DM-F series monitor.
6.3 Touch Panel Driver Installation
WARNING:
Before the touch screen driver is installed, make sure th e system is
connected to the m onitor with a USB cable or an RS-232 null cab le.
Also, make sure the VG A connect or on th e system is connec ted to t he
VGA connector on the bottom of the monitor.
To install the touch panel driver for the DM-F series, please follow the instructions below:
Step 1: Connect the DM-F series monitor to the single board computer. See above.
Step 2: Install the driver CD. Install the driver CD into the system to which the DM-F
series monitor is connected.
Step 3: Select the Touch Screen option in the menu of driver CD. The directory in
Figure 6-1 appears.
DM-F Series Monitor
Page 52
Figure 6-1: Setup Icon
Step 4: Double click the setup icon in Figure 6-1.
Step 5: The Welcome screen in Figure 6-2 appears.
Figure 6-2: Welcome Screen
Step 6: Click Next to continue.
Step 7: The license agreement in Figure 6-3 appears. Accept the terms of the
agreement by clicking I Agree.
DM-F Series Monitor
Page 53
Figure 6-3: License Agreement
Step 8: The installation destination screen appears. See Figure 6-4. Click Install.
Figure 6-4: Initiate Install
Step 9: The installation of the program begins. See Figure 6-5.
DM-F Series Monitor
Page 54
Figure 6-5: Installation Starts
Step 10: When the installation is complete, the complete screen appears. See Figure 6-6.
To complete the installation process click Finish.
Figure 6-6: Finish Installation
DM-F Series Monitor
Page 55
6.4 Change the Touch Screen Interface
If the touch screen interface must be changed from an RS-232 interface to a USB
interface or, from a USB interface to an RS-232 i nterface, the following steps m ust be
followed.
Step 1: Uninstall the touch screen driver
Step 2: Remove the interface cable i.e. remove the RS-232 cable or the USB cable
Step 3: Install the new cable i.e. install the USB cable or the RS-232 cable.
Step 4: Reinstall the driver CD as described above. S tep 0:
6.5 Calibrating the Touch Screen
To calibrate the touch sc reen cursor with th e motion of the touch scr een pen (or finger),
please follow the steps below:
Step 1: Make sure the system is properly connected through an RS-232 or a USB
interface to the DM-F series monitor.
Step 2: Make sure the touch screen driver is properly installed.
Step 3: Locate the PenMount Monitor icon in the bottom left corner of the screen.
Figure 6-7: PenMount Monitor Icon
Step 4: Click the icon. A pop up menu appears. See Figure 6-8.
DM-F Series Monitor
Page 56
Figure 6-8: PenMount Monitor Popup Menu
Step 5: Click Control Panel in the pop up menu shown in Figure 6-8.
Step 6: The configuration screen in Figure 6-9 appears.
Figure 6-9: Configuration Screen
Step 7: Double click the PenMount 6000 icon as shown in Figure 6-9.
Step 8: The calibration initiation screen in Figure 6-10 appears.
Step 9: Select the Standard Calibration button as shown in Figure 6-10.
DM-F Series Monitor
Page 57
Figure 6-10: Calibration Initiation Screen
Step 10: The calibration screen in is shown. See Figure 6-11.
Figure 6-11: Calibration Screen
Step 11: Follow the instructions. The user is asked touch the screen at five specified
points after which the screen is calibrated. Step 0:
DM-F Series Monitor
Page 58
Appendix
A
A Safety Precautions
DM-F Series Monitor
Page 59
WARNING:
The precautions outlined in this chapter should be strictly followed.
Failure to follow thes e pr ecaut ions may result in permanen t damage to
the DM-F Series.
A.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
A.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
Follow the electrostatic precautions outlined below whenever the DM-F
Series is opened.
Make sure the power is turned off and the power cord is disconnected
whenever the DM-F Series is being installed, moved or modified.
Do not apply voltage levels that exce ed the specified voltage range.
Doing so may cause fire and/or an electrical shock.
Electric shocks can occur if the DM-F Series chassis is opened when the
DM-F Series is running.
Do not drop or insert any objects into the ventilation openings of the DM-F
Series.
If considerable amounts of dust, water, or fluids enter the DM-F Series,
turn off the power supply immediately, unplug the power cord, and contact the
DM-F Series vendor.
DO NOT:
o Drop the DM-F Series against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated temperature
DM-F Series Monitor
Page 60
A.1.2 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the DM-F
Series may result in permanent damage to the DM-F Series and severe
injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the DM-F Series. Dry climat es are especiall y susceptible to ESD. It is therefor e
critical that whenever the DM-F Series is opened and any of the electrical components are
handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging any electrical component.
Self-grounding: Before handling any electrical component, touch any
grounded conducting material. During the time the electrical component is
handled, frequently touch any conducting materials that are connected to the
ground.
Use an anti-static pad: When configuring or working with an electr ical
component, place it on an antic-static pad. This reduces the possibility of ESD
damage.
Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
A.2 Maintenance and Cleaning Precautions
When maintaining or cleaning the DM-F Series, please follow the guidelines below.
A.2.1 Maintenance and Cleaning
Prior to cleaning any part or component of the DM-F Series, pl e ase re ad t he de tai ls b elow .
Except for the LCD panel, never spray or squirt liquids directly onto any other
components. To clean the LCD panel, gently wipe it with a piece of soft dry
cloth or a slightly moistened cloth.
DM-F Series Monitor
Page 61
The interior of the DM-F Series does not require cleaning. Keep fluids away
from the DM-F Series interior.
Be cautious of all small removable components when vacuuming the DM-F
Series.
Turn the DM-F Series off before cleaning the DM-F Series.
Never drop any objects or liquids through the openings of the DM-F Series.
Be cautious of any possible allergic reactions to solvents or chemicals used
when cleaning the DM-F Series.
Avoid eating, drinking and smoking within vicinity of the DM-F Series.
A.2.2 Cleaning Tools
Some components i n the DM-F Series m ay only be clean ed using a produc t specifically
designed for the purpose. In such case, t he product will be explicitly mentioned in the
cleaning tips. Below is a list of items to use when cleaning the DM-F Series.
Cloth – Although paper towels or tissues can be used, a soft, clean piece of
cloth is recommended when cleaning the DM-F Series.
Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol
can be used to clean the DM-F Series.
Using solvents – The use of solvents is not recommended when cleaning the
DM-F Series as they may damage the plastic parts.
Vacuum cleaner – Using a vacuum specifically designed for computers is one
of the best methods of cleaning the DM-F Series. Dust and dirt can restrict the
airflow in the DM-F Series and cause its circuitry to corrode.
Cotton swabs - Cotto n s waps moistene d with rub bi ng alcoh ol or wat er are
excellent tools for wiping hard to reach areas.
Foam swabs - Whenever possible, it is best to use lint free swabs such as
foam swabs for cleaning.
DM-F Series Monitor
Page 62
Appendix
B
B Certifications
DM-F Series Monitor
Page 63
B.1 RoHS Compliant
All models in the DM-F LCD monitor series comply with the Restriction of Hazardous
Materials (RoHS) Directive. This means that all com ponents used to build the industrial
workstations and the workstation itself are RoHS compliant.
The RoHS Directi ve bans the placing on the EU market of n ew electrical and ele ctronic
equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent
chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE)
flame retardants.
B.2 IP 65 Compliant Front Panel
The front panels on all five models in the DM-F series LCD monitors have an ingress
protection rating (IP) of 65, IP65. The front panels are protec ted from dust particles and
water spray.
DM-F Series Monitor
Page 64
Appendix
C
C smartOSD
DM-F Series Monitor
Page 65
C.1 IEI smartOS D Quick Installation Guide
IEI smartOSD is a proprietary On-Screen-Displ ay (OSD) software solution f rom IEI that
enables easy, remote monitor setting adjustments in a Windows environment. IEI
smartOSD delivers excellent performance and provides more flexibility than the typical
OSD hardware solutions when adjusting a monitor. smartOSD also allows monitor
settings such as brightness, contrast, screen position, size, color gain to be read and
changed over normal video cable (VGA or DVI).
C.2 Pre-inst allation Not ice
Before installing smartOSD software, please make sure one of the following operating
systems is installed:
Windows 95
Windows NT 4.0
Windows 98
Windows 2000
Windows 2003
Windows XP
Windows Vista
Windows 7
C.3 smartOSD Install
Connect the DM-F series to a host computer. Insert the CD that came with the system and
follow the instructions below.
Step 1: Insert the CD into a CD drive connected to the system.
Step 2: Locate the setup file and double click on it.
Step 3: The welcome screen shown in Figure 6-12 appears.
DM-F Series Monitor
Page 66
Figure 6-12: smartOSD Welcome Screen
Step 4: Click Next to continue.
Step 5: The Folder Select screen in Figure 6-13 appears.
Figure 6-13: smartOSD Folder Select Screen
Step 6: Select the installation folder in Figure 6-13 shown above.
Step 7: Click Next to continue.
Step 8: The screen in Figure 6-14 appears.
DM-F Series Monitor
Page 67
Figure 6-14: smartOSD Confirm Installation
Step 9: Confirm the installation by clicking Next in the screen above.
Step 10: The program starts to install and the progress bar shown in Figure 6-15 appears.
Figure 6-15: smartOSD Installation Progress
Step 11: When the installation is complete the “Complete Installation” screen in Figure
6-16 appears.
DM-F Series Monitor
Page 68
Figure 6-16: smartOSD Installation Complete
Step 12: Click Close in the screen above.
Step 13: After quick setup is complete, the IEI smartOSD wizard logo appears on the
desktop as shown in the screen below.
Step 14: To access the smartOSD, click the smartOSD wizard logo.Ste p 0:
C.4 Software Illus tration
The table below shows the smartOSD menu structure for all IEI LCD monitors.
DM-F Series Monitor
Page 69
NOTE:
To update the display setting status immediately, push the refresh
button on every page
To turn the system on, press ALT + P.
Ite m Elements
Management
Save/Load File
Power Management
EDID
EDID contains basic information about the monitor and its
capabilities.
Image
Brightness
Contrast
Sharpness
Display
Auto Adjust
Phase
Clock
Color
Auto Color
User Red Gain
User Green Gain
User Blue Gain
Color T emperature
Gamma (disabled in the DM-F Series)
PIP
PIP (disabled in the DM-F Series)
PIP Source Input (disabled in the DM-F Series)
PIP Size (disabled in the DM-F Series)
System
Monitor Power Control
DM-F Series Monitor
Page 70
Auto Brightness (disabled in the DM-F Series)
Main Source Input (YPbPr, S-Video and CVBS disabled)
Volume (disabled in the DM-F Series)
Factory Presets/OSD Lock/OSD Unlock
Mute (disabled in the DM-F Series)
Table C-1: SmartOSD Menu Structure
DM-F Series Monitor
Page 71
C.4.1 Manage Page
Figure C-17: Manage Page
DM-F Series Monitor
Page 72
C.4.2 E DID Page
Figure C-18: EDID Page
DM-F Series Monitor
Page 73
C.4.3 Ima g e Page
Figure C-19: Image Page
DM-F Series Monitor
Page 74
C.4.4 Display Page (for analog signal)
Figure C-20: Display Page
DM-F Series Monitor
Page 75
C.4.5 Color Page
Figure C-21: Color Page
DM-F Series Monitor
Page 76
C.4.6 PIP Page
NOTE:
The functions in the PIP page are only available in the MLCD-KIT
Series and AFOLUX Series monitors.
Figure C-22: PIP Page
DM-F Series Monitor
Page 77
C.4.7 System Page
Figure C-23: System Page
NOTE:
Some of the functions in the System Page are only available to some of
the IEI LCD series as following:
Auto Brightness: SRM, MLCD-KIT and AFOLUX series
only
Main Source Input: MLCD-KIT and AFOLUX series only
Volume: AFOLUX series only
Mute: AFOLUX series only
DM-F Series Monitor
Page 78
C.4.8 About Page
Figure C-24: About Page
DM-F Series Monitor
Page 79
C.5 smartOSD FAQ
For troubleshooting, please see the steps below:
C.5.1 Windows 2000 Installation Failure
Installation fails under Windows 2000 and shows the following image:
Figure C-25: DLL Missing
Solution: Download and install service pac k Windows Installer 3.1
C.5.2 Vis ta Installation Failure
Installation fail under Vista while showing following image:
Figure C-26: Windows Vista Error
DM-F Series Monitor
Page 80
Solution: Install SmartOSD.exe as the administrator authority
Figure C-27: Install as Administrator
C.5.3 Model Failure
The Model Fail error message shown below appears.
Figure C-28: Firmware Incompatibility
Solution: SmartOSD only supports firmware version 2.0 and following versions.
DM-F Series Monitor
Page 81
C.5.4 DDC Port F ailure
The DDC port fail error message shown below appears.
Figure C-29: DDC Port Failure
Solutions:
Check VGA or DVI cable
Check an IEI monitor is being used
Make sure the version is version 2.3 for the AFOLUX/MDM series and version
1.5 for the DM/ISDM/TDM/SRM/LCD-KIT series that have the SmartOSD
functions
Check if the OSD control status is busy. A busy signal may cause the signal
message for a short time.
Loading...