IEI Technology DM-F08A/R-R10, DM-F15A/PC-R10, DM-F12A/R-R10, DM-F12A/PC-R10, DM-F17A/R-R10 User Manual

...
DM-F Series Monitor
DM Series Industrial Monitor
MODEL:
DM-F Series
6.5”/8”/12”/15”/17”/19”/21.5”/24” LCD Monitor
DisplayPort, HDMI, VGA, IP 65 Protection, RoHS
User Manual
Rev. 1.16 – November 25, 2016
Page I
DM-F Series Monitor
Revision
Date Version Changes
November 25, 2016 1.16 Added Section 3.3.3: Cabinet and Rack Installation (for
F19A)
September 20, 2016 1.15 Updated Section 1.3: Model Variations
Updated Section 1.7.2: DM-F12A ~ DM-F19A Connec tors Updated Section 1.8: Technic al Specifications Updated Section 1.9.6: DM-F19A Physical Dimensions
fied Section 3.3.1: Panel Mounting
Modi
fied Section 3.3.2: Cabinet and Rack Installation
Modi January 21, 2016 1.14 Added 6.5”, 8” and 19” model information August 6, 2015 1.13 Added Section 3.2.8.1: Installing RS-232 Connector April 29, 2015 1.12 Update Figure 3-2: 3-pin Terminal Block March 4, 2015 1.11 Update Section 1.6: Technical Specifications
Update Section 1.8: Physical Dimensio ns
Update Section 3.4.1: Panel Mounting (cut-out
dimensions also updated) December 23, 2014 1.10 Update to R11 version June 10, 2014 1.01 Update Section 4.4.1: Panel Mounting March 25, 2014 1.00 Initial Release
Page II
DM-F Series Monitor
Safety Instructions
Warning! Read the user manual before connecting the system to the power
source.
Vorsicht! Bitte lesen Sie die Bedienungsanleitung, bevor Sie das System an eine
Stromquelle anschließen.
Attention! Avant de brancher le système à la source d'alimentation, consultez le
mode d'emploi.
Avvertenza! Consultare il manuale utente prima di collegare il sistema all'alimentatore. Atención! Lea atentamente este manual del usuario antes de operar la fuente de alimentación.
警告!在將系統連接到電源之前,請仔細閱讀使用手冊。 警告!在将系统连接到电源之前,请仔细阅读使用手册。
Warning! To prevent the system from overheating, do not operate it in an area that
exceeds the maximum operating temperature described in the user manual.
Vorsicht! Um eine Überhitzung des Systems zu vermeiden, betreiben Sie es ausschließlich im zulässigen Betriebstemperaturbereich. Dieser ist in der Bedienungsanleitung vermerkt.
Attention! Pour éviter la surchauffe du système, ne l'utilisez pas dans une zone
dont la température dépasse les limites décrits dans le mode d'emploi.
Avvertenza! Per evitare che il sistema si surriscaldi, non utilizzarlo in aree che
superino la temperatura massima d'esercizio descritta nel manuale utente.
Atención! Para evitar el excesivo calentamiento del sistema, no opere en las
condiciones de temperatura superior a lo recomendado en este manual del usuario.
警告!為防止系統過熱,不要在超過使用手冊上記載的產品工作溫度範圍之外操作
此系統。
警告!为防止系统过热,不要在超过使用手册上记载的产品工作温度范围之外操作
此系统。
Page III
DM-F Series Monitor
Warning! Use only the adapter and power cord approved for this system. Use of
another type of adapter may risk fire or explosion. Please refer to the user manual
for the power adapter specifications. Vorsicht! Nur zugelassene Netzteile und Netzkabel dürfen verwendet werden. Die Benutzung von anderen Netzteilen kann einen Brand oder eine Explosion zur Folge haben. Prüfen Sie die jeweiligen Spezifikationen in der Bedienungsanleitung. Attention! Utilisez exclusivement le câble d'alimentation et l’adaptateur
homologués pour ce système. L’utilisation d’un autre type d’adaptateur risquerait
de provoquer un incendie ou une explosion. Veuillez référer au mode d'emploi
pour les spécifications de l'adaptateur d'alimentation. Avvertenza! Utilizzare solo l'adattatore e il cavo di alimentazione approvati per
questo sistema. L'uso di un altro tipo di adattatore può causare rischio d'incendio
o esplosione. Si prega di fare riferimento al manuale utente per le specifiche
sull'alimentazione. Atención! Utilice solamente el adaptador de corriente alterna (CA) con Marcas
Conformidad otorgadas. Cualquier otro adaptador no otorgado aumenta el riesgo
de explosión o incendio. Por favor consulte el manual del usuario para las
especificaciones del adaptador de alimentación.
警告!只能使用經過認證、適用於本系統的電源變壓器與電源線。使用不適用的電
源變壓器將可能導致火災或爆炸。電源變壓器規格請參考使用手冊。
警告!只能使用经过认证,适用于本系统的电源适配器与电源线。使用不适用的电
源适配器将可能导致火灾或爆炸。电源适配器规格请参考使用手册。
Warning! Ultimate disposal of this product should be handled according to all
national laws and regulations.
Vorsicht! Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und
Gesetzen des Landes erfolgen.
Attention! La mise au rebut ou le recyclage de ce produit sont généralement soumis aux lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Avvertenza! Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e i regolamenti locali. Atención! La disposición final de residuos de este producto se debe cumplir con las normativas y leyes del país.
警告!本產品的廢棄處理應根據該國家的法律和規章進行。 警告!本产品的废弃处理应根据该国家的法律和规章进行。
Page IV
DM-F Series Monitor
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page V
DM-F Series Monitor
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.
HOT SURFACE
This symbol indicates a hot surface that should not be touched without
taking care.
Page VI
DM-F Series Monitor
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 FEATURES................................................................................................................... 2
1.3 MODEL VARIATIONS ................................................................................................... 3
1.4 APPLICATIONS ............................................................................................................ 3
1.5 FRONT VIEW .............................................................................................................. 4
1.6 REAR VIEW ................................................................................................................ 5
1.7 CONNECTORS ............................................................................................................. 6
1.7.1 DM-F65A and DM-F08A Connectors............................................................... 6
1.7.2 DM-F12A ~ DM-F19A Connectors...................................................................7
1.7.3 DM-F22A and DM-F24A Connectors............................................................... 7
1.8 TECHNICAL SPECIFICATIONS ...................................................................................... 8
1.9 PHYSICAL DIMENSIONS............................................................................................ 10
1.9.1 DM-F65A Physical Dimensions....................................................................... 10
1.9.2 DM-F08A Physical Dimensions........................................................................11
1.9.3 DM-F12A Physical Dimensions....................................................................... 12
1.9.4 DM-F15A Physical Dimensions....................................................................... 13
1.9.5 DM-F17A Physical Dimensions....................................................................... 14
1.9.6 DM-F19A Physical Dimensions....................................................................... 15
1.9.7 DM-F22A Physical Dimensions....................................................................... 16
1.9.8 DM-F24A Physical Dimensions....................................................................... 17
2 UNPACKING ............................................................................................................... 18
2.1 UNPACKING PROCEDURE.......................................................................................... 19
2.2 PACKING LIST........................................................................................................... 20
2.3 OPTIONAL ITEMS...................................................................................................... 21
3 INSTALLATION ......................................................................................................... 22
3.1 INSTALLATION PRECAUTIONS................................................................................... 23
3.2 EXTERNAL PERIPHERAL DEVICE CONNECTION ........................................................ 24
3.2.1 DC-in Jack....................................................................................................... 24
Page VII
DM-F Series Monitor
3.2.2 9 V–36 V Terminal Block (Optional)................................................................ 24
3.2.3 USB for Touch Panel Connector...................................................................... 25
3.2.4 VGA Connector................................................................................................ 25
3.2.5 DVI-D Connector (F65A, F08A and F19A Only)............................................ 26
3.2.6 DisplayPort Connector (F12A ~ F24A Only).................................................. 27
3.2.7 HDMI Connector (F12A, F15A, F17A, F22A and F24A Only)....................... 28
3.2.8 RS-232 Port for Touch Panel (Reserved for Resistive Touch) ......................... 28
3.2.8.1 Installing RS-232 Connector..................................................................... 29
MOUNTING THE MONITOR........................................................................................ 31
3.3
3.3.1 Panel Mounting................................................................................................ 31
3.3.2 Cabinet and Rack Installation (for F65A ~ F17A).......................................... 39
3.3.3 Cabinet and Rack Installation (for F19A)....................................................... 41
3.3.4 Wall Mounting.................................................................................................. 44
3.3.5 Stand Installation............................................................................................. 46
3.3.6 Arm Installation ............................................................................................... 47
4 ON-SCREEN-DISPLAY (OSD) CONTROLS.......................................................... 49
4.1
OSD KEYPAD........................................................................................................... 50
4.2 OSD MENU STRUCTURE .......................................................................................... 52
4.3 USING THE OSD....................................................................................................... 53
4.3.1 Image Menu ..................................................................................................... 53
4.3.1.1 Color Setting............................................................................................. 54
4.3.2 Display Menu................................................................................................... 55
4.3.3 System Menu .................................................................................................... 56
4.3.3.1 Input.......................................................................................................... 57
4.3.3.2 OSD Settings............................................................................................. 58
5 SOFTWARE DRIVERS.............................................................................................. 59
INTRODUCTION......................................................................................................... 60
5.1
5.2 RS-232 OR USB TOUCHSCREEN............................................................................... 60
5.3 TOUCH PANEL DRIVER INSTALLATION...................................................................... 61
5.4 CHANGE THE TOUCHSCREEN INTERFACE.................................................................. 65
5.5 CALIBRATING THE TOUCHSCREEN............................................................................ 65
6 AD BOARDS ................................................................................................................ 68
6.1 AD BOARD OVERVIEW............................................................................................. 69
Page VIII
DM-F Series Monitor
AV-6038 AD BOARD................................................................................................ 69
6.2
6.2.1 AV-6038 Peripheral Interface Connectors....................................................... 70
6.2.2 Backlight Inverter Connector (INVERTER1) .................................................. 71
6.2.3 LVDS Connector (LVDS1) ............................................................................... 71
6.2.4 OSD Keypad Connector (CN14)...................................................................... 72
6.2.5 Power Input Connector (CN9)......................................................................... 72
6.2.6 RS-232 Connector for Touchscreen (RS232_1)............................................... 72
6.2.7 USB Connector for Touchscreen (USB_TOUCH1)......................................... 73
6.2.8 Touchscreen Connector (J1)............................................................................ 73
6.2.9 LVDS Panel Voltage Select Jumper (JP2) ....................................................... 73
6.2.10 EIDE Firmware Update Jumper (JP3).......................................................... 73
6.3
AV-60381 AD BOARD.............................................................................................. 74
6.3.1 AV-60381 Peripheral Interface Connectors..................................................... 74
6.3.2 Backlight Inverter Connector (INVERTER1) .................................................. 75
6.3.3 LVDS Connector (LVDS1) ............................................................................... 76
6.3.4 OSD Keypad Connector (KEYPAD1) .............................................................. 76
6.3.5 Power Input Connector (PWR2)...................................................................... 77
6.3.6 RS-232 Connector for Touchscreen (RS232_1)............................................... 77
6.3.7 USB Connector for Touchscreen (USB_TOUCH1)......................................... 77
6.3.8 Touchscreen Connector (J1)............................................................................ 77
6.3.9 VGA Connector (VGA2)................................................................................... 78
6.3.10 Backlight Voltage Select Jumper (JP5).......................................................... 78
6.3.11 LVDS Panel Voltage Select Jumper (JP2)...................................................... 78
6.3.12 Power Input Setting Jumper (JP4)................................................................. 79
6.3.13 Touchscreen Type Select Jumper (JP1).......................................................... 79
A REGULATORY COMPLIANCE.............................................................................. 80
B SAFETY PRECAUTIONS......................................................................................... 82
SAFETY PRECAUTIONS............................................................................................. 83
B.1
B.1.1 General Safety Precautions............................................................................. 83
B.1.2 Anti-static Precautions.................................................................................... 84
B.1.3 Product Disposal............................................................................................. 85
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 86
B.2.1 Maintenance and Cleaning.............................................................................. 86
B.2.2 Cleaning Tools................................................................................................. 86
Page IX
DM-F Series Monitor
C SMARTOSD................................................................................................................ 88
IEI SMARTOSD QUICK INSTALLATION GUIDE ......................................................... 89
C.1
C.2 PRE-INSTALLATION NOTICE..................................................................................... 89
C.3 SMARTOSD INSTALLATION...................................................................................... 89
C.4 SOFTWARE ILLUSTRATION ....................................................................................... 92
C.4.1 Manage Page................................................................................................... 95
C.4.2 EDID Page...................................................................................................... 96
C.4.3 Image Page...................................................................................................... 97
C.4.4 Display Page (for analog signal).................................................................... 98
C.4.5 Color Page ...................................................................................................... 99
C.4.6 PIP Page........................................................................................................ 100
C.4.7 System Page................................................................................................... 101
C.4.8 About Page .................................................................................................... 102
C.5
SMARTOSD FAQ................................................................................................... 103
C.5.1 Windows 2000 Installation Failure............................................................... 103
C.5.2 Vista Installation Failure............................................................................... 103
C.5.3 Model Failure................................................................................................ 104
C.5.4 DDC Port Failure ......................................................................................... 105
Page X
DM-F Series Monitor
List of Figures
Figure 1-1: DM-F Series .................................................................................................................2
Figure 1-2: Typical Monitor Front View........................................................................................4
Figure 1-3: 6.5” and 8” Rear View.................................................................................................5
Figure 1-4: 12”–24” Rear View ......................................................................................................5
Figure 1-5: Bottom Panel Connectors (DM-F65A/08A)...............................................................6
Figure 1-6: Side Panel Connectors (DM-F65A/08A)....................................................................6
Figure 1-7: Bottom Panel Connectors (DM-F12A/15A/17A/19A)................................................7
Figure 1-8: Side Panel Connector (DM-F12A/15A/17A/19A).......................................................7
Figure 1-9: Bottom Panel Connectors (DM-F22A/24A)...............................................................7
Figure 1-10: DM-F65A Physical Dimensions (Unit: mm) ..........................................................10
Figure 1-11: DM-F08A Physical Dimensions (Unit: mm) ..........................................................11
Figure 1-12: DM-F12A Physical Dimensions (Unit: mm) ..........................................................12
Figure 1-13: DM-F15A Physical Dimensions (Unit: mm) ..........................................................13
Figure 1-14: DM-F17A Physical Dimensions (Unit: mm) ..........................................................14
Figure 1-15: DM-F19A Physical Dimensions (Unit: mm) ..........................................................15
Figure 1-16: DM-F22A Physical Dimensions (Unit: mm) ..........................................................16
Figure 1-17: DM-F24A Physical Dimensions (Unit: mm) ..........................................................17
Figure 3-1: DC Jack......................................................................................................................24
Figure 3-2: 3-pin Terminal Block.................................................................................................24
Figure 3-3: USB Touch Panel Connector...................................................................................25
Figure 3-4: VGA Connector .........................................................................................................25
Figure 3-5: DVI-D connector........................................................................................................26
Figure 3-6: DisplayPort connector..............................................................................................27
Figure 3-7: HDMI Connector........................................................................................................28
Figure 3-8: RS-232 Touch Panel Connector ..............................................................................29
Figure 3-9: Rear Panel Retention Screw Removal (6.5” & 8”) .................................................29
Figure 3-10: Rear Panel Retention Screw Removal (12”–24”).................................................30
Figure 3-11: Connecting RS-232 Cable ......................................................................................30
Figure 3-12: Hex Jack Screws for Securing RS-232 Connector..............................................31
Figure 3-13: Mounting Clamps Holder........................................................................................32
Page XI
Figure 3-14: Mounting Clamps....................................................................................................32
Figure 3-15: DM-F65A Cutout Dimensions (Unit: mm) .............................................................33
Figure 3-16: DM-F08A Cutout Dimensions (Unit: mm) .............................................................33
Figure 3-17: DM-F12A Cutout Dimensions (Unit: mm) .............................................................33
Figure 3-18: DM-F15A Cutout Dimensions (Unit: mm) .............................................................34
Figure 3-19: DM-F17A Cutout Dimensions (Unit: mm) .............................................................34
Figure 3-20: DM-F19A Cutout Dimensions (Unit: mm) .............................................................34
Figure 3-21: DM-F22A Cutout Dimensions (Unit: mm) .............................................................35
Figure 3-22: DM-F24A Cutout Dimensions (Unit: mm) .............................................................35
Figure 3-23: Secure the Mounting Clamp Holders....................................................................36
Figure 3-24: Slide into the Panel.................................................................................................36
Figure 3-25: Panel Mounting Clamp Installation.......................................................................37
Figure 3-26: Mounting Clamps Holder Dimensions..................................................................37
Figure 3-27: Ultra Set Plate Dimensions....................................................................................38
DM-F Series Monitor
Figure 3-28: Bolt Dimensions......................................................................................................38
Figure 3-29: Steering Button Dimensions..................................................................................38
Figure 3-30: Secure the Mounting Clamp Holders....................................................................39
Figure 3-31: Slide into the Rack/Cabinet Bracket .....................................................................40
Figure 3-32: Secure the Rack/Cabinet Bracket..........................................................................40
Figure 3-33: Install into a Rack/Cabinet .....................................................................................41
Figure 3-34: Slide DM-F19A into the Rack/Cabinet Bracket.....................................................42
Figure 3-35: Secure the Mounting Brackets..............................................................................42
Figure 3-36: Install DM-F19A into a Rack/Cabinet.....................................................................43
Figure 3-37: Attach Wall Mounting Kit to the Wall ....................................................................44
Figure 3-38: Hook Onto Wall Mounting Kit ................................................................................45
Figure 3-39: Tighten Retention Screw........................................................................................45
Figure 3-40: VESA Mounting Holes (6.5” & 8”)..........................................................................46
Figure 3-41: VESA Mounting Holes (12”–24”)...........................................................................46
Figure 3-42: Monitor Stand Mounting.........................................................................................47
Figure 3-43: Monitor Arm Mounting............................................................................................48
Figure 4-1: OSD Keypad for 6.5” and 8” Monitors....................................................................50
Figure 4-2: OSD Keypad for 12”–24” Monitors..........................................................................51
Figure 4-3: Image Menu ...............................................................................................................53
Figure 4-4: Color Settings............................................................................................................54
Figure 4-5: Display Menu.............................................................................................................55
Page XII
DM-F Series Monitor
Figure 4-6: System Menu.............................................................................................................56
Figure 4-7: Input Options.............................................................................................................57
Figure 4-8: OSD Settings Menu...................................................................................................58
Figure 5-1: Setup Icon..................................................................................................................62
Figure 5-2: Welcome Screen .......................................................................................................62
Figure 5-3: License Agreement...................................................................................................63
Figure 5-4: Initiate Install .............................................................................................................63
Figure 5-5: Installation Starts......................................................................................................64
Figure 5-6: Finish Installation......................................................................................................64
Figure 5-7: PenMount Monitor Icon............................................................................................65
Figure 5-8: PenMount Monitor Popup Menu..............................................................................66
Figure 5-9: Configuration Screen................................................................................................66
Figure 5-10: Calibration Initiation Screen..................................................................................67
Figure 5-11: Calibration Screen ..................................................................................................67
Figure 6-1: AV-6038 AD Board Layout Diagram........................................................................69
Figure 6-2: AV-60381 AD Board Layout Diagram......................................................................74
Page XIII
DM-F Series Monitor
List of Tables
Table 1-1: DM-F Series Model Variations.....................................................................................3
Table 1-2: DM-F Series Specifications..........................................................................................9
Table 2-1: Packing List.................................................................................................................20
Table 3-1: USB Touch Panel Connector Pinouts ......................................................................25
Table 3-2: VGA Connector Pinouts.............................................................................................25
Table 3-3: DVI-D Connector Pinouts...........................................................................................26
Table 3-4: Display Port Connector Pinouts ...............................................................................27
Table 3-5: HDMI Connector Pinouts ...........................................................................................28
Table 3-6: RS-232 Touch Panel Connector Pinouts..................................................................28
Table 3-7: Panel Mounting Clamps.............................................................................................32
Table 4-1: OSD Control Buttons for 6.5” and 8” Monitors .......................................................50
Table 4-2: OSD Control Buttons for 12”–24” Monitors.............................................................51
Table 4-3: OSD Menu Structure...................................................................................................52
Table 6-1: AV-6038 Peripheral Interface Connectors................................................................70
Table 6-2: Backlight Inverter Connector (INVERTER1) Pinouts..............................................71
Table 6-3: LVDS Connector (LVDS1) Pinouts............................................................................71
Table 6-4: OSD Keypad Connector (CN14) Pinouts..................................................................72
Table 6-5: Power Input Connector (CN9) Pinouts.....................................................................72
Table 6-6: RS-232 Connector for Touchscreen (RS232_1) Pinouts ........................................72
Table 6-7: USB Connector for Touchscreen (USB_TOUCH1) Pinouts....................................73
Table 6-8: Touchscreen Connector (J1) Pinouts.......................................................................73
Table 6-9: LVDS Panel Voltage Select Jumper (JP2) Pinouts..................................................73
Table 6-10: EIDE Firmware Update Jumper (JP3) Pinouts.......................................................73
Table 6-11: AV-60381 Peripheral Interface Connectors............................................................75
Table 6-12: Backlight Inverter Connector (INVERTER1) Pinouts............................................75
Table 6-13: LVDS Connector (LVDS1) Pinouts..........................................................................76
Table 6-14: OSD Keypad Connector (KEYPAD1) Pinouts........................................................76
Table 6-15: Power Input Connector (PWR2) Pinouts................................................................77
Table 6-16: RS-232 Connector for Touchscreen (RS232_1) Pinouts ......................................77
Table 6-17: USB Connector for Touchscreen (USB_TOUCH1) Pinouts..................................77
Table 6-18: Touchscreen Connector (J1) Pinouts.....................................................................78
Page XIV
DM-F Series Monitor
Table 6-19: VGA Connector (VGA2) Pinouts .............................................................................78
Table 6-20: Backlight Voltage Select Jumper (JP5) Pinouts....................................................78
Table 6-21: LVDS Panel Voltage Select Jumper (JP2) Pinouts................................................78
Table 6-22: Power Input Setting Jumper (JP4) Pinouts............................................................79
Table 6-23: Touchscreen Type Select Jumper (JP1) Pinouts..................................................79
Table C-1: SmartOSD Menu Structure........................................................................................94
Page XV
DM-F Series Monitor
Chapter
1

1 Introduction

Page 1

1.1 Overview

Figure 1-1: DM-F Series
DM-F Series Monitor
The DM-F series LCD monitor is the latest member of IEI’s line of sophisticated LCD
designs with flat bezel. It is designed to fit industrial automation, or any other applications
that require minimum installation space and flexible configuration. The flat front panel
provides IP 65 protection, which effectively wards off dust and water. Flexible analog or
digital interfaces are provided for ease of connection with a management computer.

1.2 Features

The DM-F series have the following standard features:
Robust IP 65 aluminum front bezel
Aesthetic ultra-thin bezel for seamless panel mount installation
Wide range DC input: 9 V–36 V or 12 V
Flexible video input solution: VGA, HDMI, DisplayPort or DVI-D
Resistive single touch or projected capacitive multi-touch options available
Page 2
DM-F Series Monitor

1.3 Model Variations

The DM-F series LCD monitor base models have a variety of variants. The model
variations are listed in
Model Number LCD Touchscreen Power VGA HDMI/DVI DisplayPort
DM-F65A/R-R10 6.5” Resistive 12 V Yes DM-F08A/R-R10 8” Resistive 12 V Yes DM-F12A/R-R10 DM-F12A/PC-R10 DM-F15A/R-R10 Resistive 9~36 V Yes DM-F15A/PC-R10 DM-F17A/R-R10 DM-F17A/PC-R10 DM-F19A/R-R10 DM-F19A/PC-R10 DM-F22A/PC-R10 21.5” Capacitive 9~36 V Yes DM-F24A/PC-R10 24” Capacitive 9~36 V Yes
4Table 1-1.
12”
15”
17”
19”
Resistive 9~36 V Yes
Capacitive 9~36 V Yes
Capacitive 9~36 V Yes
Resistive 9~36 V Yes
Capacitive 9~36 V Yes
Resistive 9~36 V Yes
Capacitive 9~36 V Yes
DVI-D No DVI-D No
HDMI Yes HDMI Yes HDMI Yes HDMI Yes HDMI Yes
HDMI Yes DVI-D Yes DVI-D Yes
HDMI Yes
HDMI Yes
Table 1-1: DM-F Series Model Variations

1.4 Applications

The DM-F series LCD monitor is designed for rigorous industrial environments where it
may be exposed to both heat and moisture. Its durability and strength also makes it an
ideal choice for public access computers. Some possible applications include:
Digital surveillance
Multimedia advertising platform
General Computing
o Computer-based testing center o General purpose information system o Mobile nursing station o Interactive education use
Automation & Control
o Plant environment monitoring o Factory automation HMI terminal
Page 3
o Shop-floor/MES control
Self-service Kiosk
o Full-service receptionist kiosk o Hospital self-registration terminal o Interactive photo kiosk o Video rental kiosk o Self-service POS terminal

1.5 Front View

The front of the DM-F series LCD monitor is a flat panel LCD screen surrounded by an
aluminum frame.
4Figure 1-2 shows a typical monitor front view.
DM-F Series Monitor
Page 4
Figure 1-2: Typical Monitor Front View
DM-F Series Monitor

1.6 Rear View

The rear panel provides access to retention screw holes that support VESA mounting. A
5-key/7-key membrane OSD keypad is also located on the rear panel.
The following diagrams show the rear panel of the DM-F series.
Figure 1-3: 6.5” and 8” Rear View
Figure 1-4: 12”–24” Rear View
Page 5

1.7 Connectors

The following sections show the I/O interfaces of the DM-F series LCD monitor. All
DM-F Series Monitor
connectors are fully described in Section

1.7.1 DM-F65A and DM-F08A Connectors

Figure 1-5: Bottom Panel Connectors (DM-F65A/08A)
43.2.
Page 6
Figure 1-6: Side Panel Connectors (DM-F65A/08A)
DM-F Series Monitor

1.7.2 DM-F12A ~ DM-F19A Connectors

Figure 1-7: Bottom Panel Connectors (DM-F12A/15A/17A/19A)
Figure 1-8: Side Panel Connector (DM-F12A/15A/17A/19A)

1.7.3 DM-F22A and DM-F24A Connectors

Figure 1-9: Bottom Panel Connectors (DM-F22A/24A)
Page 7
DM-F Series Monitor

1.8 Technical Specifications

4Table 1-2 shows the DM-F series technical specifications.
Model DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A LCD Display 6.5” (4:3) 8” (4:3) 12” (4:3) 15” (4:3) 17” (5:4) 19” (5:4) 21.5” (16 :9) 24” (16:9) Max. Resolution 640x480 800x600 1024 x768 1024 x768 1280x1024 1280x1024 1920x1080 1920x1080 Brightness Contrast Ratio 600:1 500:1 700:1 800:1 1000:1 1000:1 1000:1 3000:1 LCD Color 16.2M 262K 16.2M 16.2M 16.7M 16.7M 16.7M 16.7M Pixel Pitch (mm) 0.207 x
Viewing Angle (H/V) Backlight MTBF (Hrs) Touchscreen 5-wire resistive type 5-wire resistive type or projected capacitive type Projected capacitive type Touch Controller
AD Board AV-60381 AV-60381 AV-6038 AV-6038 AV-6038 AV-6038 AV-6038 AV-6038 OSD Button 5-key 5-key 7-key 7-key 7-key 7-key 7-key 7-key Smart OSD Yes Yes Yes Yes Yes Yes Yes Yes Dimensions (mm)
(cd/m²)
800 500 600 450 350 350 250 250
0.0675 x
0.207
160°/140° 140°/120° 160°/140°
50,000 50,000 50,000 70,000 50,000 50,000 30,000 30,000
Penmount 6000
191.8 x
0.2025
222.2 x
0.24 x
0.24
Resistive type: Penmount 6000 Projected capacitive type: EETI EXC7200
322.2 x
0.29 x
0.29
160°/150° 170°/160° 170°/160° 170°/160° 178°/178°
378.5 x
0.26 x
0.26
408.4 x
0.294 x
0.294
447.4 x
0.25 x
0.25
550.4 x
0.28 x
0.28
EETI EXC3000
600 x
(W x H x D)
Cutout Dimensions (W x H) (mm) Weight (kg) (Net/Gross) Enclosure Color Black C Black C Black C Black C Black C Black C Black C Black C Front Frame Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Rear Cover Sheet
VESA Mount 75 75 100 100 100 100 100 100
Page 8
154.36 x
42.88
180 x 140 206 x 154 305 x 245
1.1/2.6 1.33/4.5 2.7/4.9 3.5/5.5 4.4/7.1 5.4/8.4 6.3/9.6 7.6/10.9
Metal
182.2 x
42.7
Sheet Metal
262.2 x
40.5
Sheet Metal
303 x
43.2
361 x 286 391 x 324 430 x 355 532 x 340 577 x 359
Sheet Metal
341.4 x
49.3
Sheet Metal
372.4 x
49.57
Sheet Metal
358.4 x
49.1
Sheet Metal
382 x
49.4
Sheet Metal
DM-F Series Monitor
Model DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A Optional Mounting Kit
Operating Temp.
Storage Temp. -20°C ~ 70°C -20°C ~ 60°C Humidity 10% ~ 95% (non-condensing) I/O Ports
Reserved Ports 1 x RS-232 (for resistive touch) N/A Power 1 x Lockable DC-in jack
Wall Rack Panel Arm Stand
-20°C ~ 60°C (with air flow)
1 x VGA 1 x DVI 1 x USB 2.0 (for touch)
Wall Rack Panel Arm Stand
Wall Rack Panel Arm Stand
1 x VGA 1 x HDMI 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)
Wall Rack Panel Arm Stand
Wall
Wall
Rack
Panel
Panel
Arm
Arm
Stand
Stand
1 x VGA 1 x HDMI (17” only) 1 x DVI (19” only) 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)
Wall Panel Arm Stand
-10°C ~ 50°C (with air flow)
1 x VGA 1 x HDMI 1 x DisplayPort 1.1 1 x USB 2.0 (for touch)
Wall Panel Arm Stand
(12 V) Optional 9V - 36V power input terminal block
Power
12V@0.5A 12V@0.5A
Consumption IP Level IP 65 compliant front panel Safety & EMC CE, FCC
Table 1-2: DM-F Series Specifications
1 x Lockable DC-in jack (9 V - 36 V) 1 x Power input terminal block (9 V - 36 V)
9V@2.2A 36V@0.5A
9V@1.6A 36V@0.4A
9V@2.6A 36V@0.6A
9V@3.3A 36V@0.8A
9V@2.5A 36V@0.6A
9V@3.4A 36V@0.8A
Page 9

1.9 Physical Dimensions

The following sections describe the physical dimensions for each model of the DM-F
series LCD monitor.

1.9.1 DM-F65A Physical Dimensions

The physical dimensions of the DM-F65A are shown in 4Figure 1-12.
DM-F Series Monitor
Page 10
Figure 1-10: DM-F65A Physical Dimensions (Unit: mm)
DM-F Series Monitor

1.9.2 DM-F08A Physical Dimensions

The physical dimensions of the DM-F08A are shown in 4Figure 1-12.
Figure 1-11: DM-F08A Physical Dimensions (Unit: mm)
Page 11

1.9.3 DM-F12A Physical Dimensions

The physical dimensions of the DM-F12A are shown in 4Figure 1-12.
DM-F Series Monitor
Page 12
Figure 1-12: DM-F12A Physical Dimensions (Unit: mm)
DM-F Series Monitor

1.9.4 DM-F15A Physical Dimensions

The physical dimensions of the DM-F15A are shown in 4Figure 1-13.
Figure 1-13: DM-F15A Physical Dimensions (Unit: mm)
Page 13

1.9.5 DM-F17A Physical Dimensions

The physical dimensions of the DM-F17A are shown in 4Figure 1-14.
DM-F Series Monitor
Page 14
Figure 1-14: DM-F17A Physical Dimensions (Unit: mm)
DM-F Series Monitor

1.9.6 DM-F19A Physical Dimensions

The physical dimensions of the DM-F19A are shown in 4Figure 1-12.
Figure 1-15: DM-F19A Physical Dimensions (Unit: mm)
Page 15

1.9.7 DM-F22A Physical Dimensions

The physical dimensions of the DM-F22A are shown in 4Figure 1-16.
DM-F Series Monitor
Page 16
Figure 1-16: DM-F22A Physical Dimensions (Unit: mm)
DM-F Series Monitor

1.9.8 DM-F24A Physical Dimensions

The physical dimensions of the DM-F24A are shown in 4Figure 1-17.
Figure 1-17: DM-F24A Physical Dimensions (Unit: mm)
Page 17
DM-F Series Monitor
Chapter
2

2 Unpacking

Page 18
DM-F Series Monitor

2.1 Unpacking Procedure

To unpack the DM-F series LCD monitor, follow the steps below:
WARNING:
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the DM-F series LCD monitor
has been properly installed. This ensures the screen is protected during the
installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the DM-F series LCD monitor.
Step 7: Make sure all the components listed in the packing list are present. Step 0:
Page 19

2.2 Packing List

The DM-F series monitor is shipped with the following components:
Quantity Item Image
1 DM-F series
1 USB cable (for touchscreen)
(P/N: 32001-006100-100-RS)
1 VGA cable
DM-F Series Monitor
(P/N: 32000-036200-RS)
1 Touch pen (resistive touch only)
(P/N: 43125-0002C0-00-RS)
1 60W 12V DC adapter with lockable
connector (6.5” and 8” models only) (P/N: 63040-010060-120-RS)
1 Utility CD (drivers and user manual)
Table 2-1: Packing List
If any of the above items are missing or damaged, contact the distributor or sales
representative immediately.
Page 20
DM-F Series Monitor

2.3 Optional Items

The following items are optional accessories for the DM-F series monitor:
Item DM-F65A DM-F08A DM-F12A DM-F15A DM-F17A DM-F19A DM-F22A DM-F24A Arm
Stand
Wall Mount Kit
Panel Mount Kit
Rack Mount Kit
Cable Cover
RS-232 Touch
Cable Kit
HDMI Cable
DVI Cable
Display Port
Cable
Power Adapter
ARM-11-RS ARM-31-RS
STAND-B08
AFLWK-12 WK-190MS-R10
FPK-04-R10 FPK-01-R10 FPK-02-R10 FPK-03-R10
FRK65-R10 FRK08-R10 FRK12-R10 FRK15-R10 FRK17-R10 FRK19-R10 N/A
N/A DM-F-CC01-R10 DM-F-CC02-R10
N/A 32012-000100-200-RS N/A 32012-000100-200-RS
32000-086600-RS N/A 32000-086600-RS N/A
N/A 32004-000200-100-RS
N/A 63040-010060-120-RS (60W 12V DC adapter with lockable connector)
STAND-A12-RS
STAND-A19-RS, STAND-C19-RS or STAND-A21-RS
STAND-C12-RS
DM-F-COMKIT-R10 N/A
Page 21
DM-F Series Monitor
Chapter
3

3 Installation

Page 22
DM-F Series Monitor

3.1 Installation Precautions

When installing the DM-F series LCD monitor, please follow the precautions listed below:
Read the user manual: The user manual provides a complete description of
the DM-F series LCD monitor, installation instructions and configuration
options.
DANGER! Disconnect Power: Power to the monitor must be disconnected
when installing the DM-F series LCD monitor, or before any attempt is made
to access the rear panel. Electric shock and personal injury might occur if the
rear panel of the monitor is opened while the power cord is still connected to
an electrical outlet.
Qualified Personnel: The DM-F series LCD monitor must be installed and
operated only by trained and qualified personnel. Maintenance, upgrades, or
repairs may only be carried out by qualified personnel who are familiar with
the associated dangers.
Mounting: Since the monitor may weigh up to 8 kg (not including a swing arm
or other accessories), please ensure at least two people assist with mounting
the monitor.
Air Circulation: Make sure there is sufficient air circulation when installing the
monitor. Leave at least 5 cm of clearance around the monitor to prevent
overheating.
Grounding: The monitor should be properly grounded. The voltage feeds
must not be overloaded. Adjust the cabling and provide external overcharge
protection per the electrical values indicated on the label attached to the back
of the monitor.
Anti-static Discharge : The rear panel of the monitor must to be removed to
configure the monitor’s AD board. When doing so, be sure the monitor is
disconnected from its power source and take all necessary safety precautions
to avoid electrocution and static discharge to the AD board. The use of a
grounded wrist strap and an anti-static work pad is recommended.
Page 23

3.2 External Peripheral Device Connection

The external I/O connector pinouts of the DM-F series industrial monitors are described in
the following sections.

3.2.1 DC-in Jack

The lockable power connector connects to the power adapter and provides power to the
monitor. Supported power voltage is varied among models as described below:
DM-F65A/08A: 12 V  DM-F12A/15A/17A/19A/22A/24A: 9 V–36 V
DM-F Series Monitor
Figure 3-1: DC Jack

3.2.2 9 V–36 V Terminal Block (Optional)

Connect the leads of 9 V–36 V DC power supply into the terminal block. Make sure that
the power and ground wires are attached to the correct sockets of the connector.
Figure 3-2: 3-pin Terminal Block
Page 24
DM-F Series Monitor

3.2.3 USB for Touch Panel Connector

Use the rear panel standard USB touch panel connector to connect the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
1 VCC 2 USB20_N11 3 USB20_P11 4 GND
Table 3-1: USB Touch Panel Connector Pinouts
Figure 3-3: USB Touch Panel Connector

3.2.4 VGA Connector

Use the rear panel standard 15-pin female VGA connector to connect the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION
1 RED 6 GROUND 11 NC 2 GREEN 7 GROUND 12 DDCDAT 3 BLUE 8 GROUND 13 HSYNC 4 NC 9 NC 14 VSYNC 5 GROUND 10 GROUND 15 DDCCLK
Table 3-2: VGA Connector Pinouts
Figure 3-4: VGA Connector
Page 25

3.2.5 DVI-D Connector (F65A, F08A and F19A Only)

The 24-pin Digital Visual Interface (DVI) connector connects to high-speed,
high-resolution digital displays. The DVI-D connector supports only digital signals.
PIN DESCRIPTION PIN DESCRIPTION
DM-F Series Monitor
1 2 3 4 5 6 7 8 9 10 11 12
Table 3-3: DVI-D Connector Pinouts
TMDS Data2­TMDS Data2+ GND N/C N/C DDC Clock [SCL] DDC Data [SDA] Analog vertical sync TMDS Data1­TMDS Data1+ GND NC
13 14 15 16 17 18 19 20 21 22 23 24
NC PVDD1 GND GND TMDS Data0­TMDS Data0+ GND NC NC GND TMDS Clock + TMDS Clock -
Page 26
Figure 3-5: DVI-D connector
DM-F Series Monitor

3.2.6 DisplayPort Connector (F12A ~ F24A Only)

The DisplayPort connector transmits a digital signal to compatible DisplayPort display
devices such as a TV or computer screen.
PIN DESCRIPTION PIN DESCRIPTION
1 ML_L3N 2 GND 3 ML_L3P 4 ML_L2N 5 GND 6 ML_L2P 7 ML_L1N 8 GND 9 ML_L1P 10 ML_L0N 11 GND 12 ML_L0P 13 GND 14 GND 15 C_DDI0_DP_AUXP 16 GND 17 C_DDI0_DP_AUXN 18 C_DDI0_DP_HPD 19 GND 20 VCC 21 GND 22 GND 23 GND 24 GND
Table 3-4: Display Port Connector Pinouts
Figure 3-6: DisplayPort connector
Page 27
DM-F Series Monitor

3.2.7 HDMI Connector (F12A, F15A, F17A, F22A and F24A Only)

The HDMI connector connects to a display device with HDMI interface.
PIN DESCRIPTION PIN DESCRIPTION
1 HDMI_TMDS_C_DATA2 2 GND 3 HDMI_TMDS_C_DATA2# 4 HDMI_TMDS_C_DATA1 5 GND 6 HDMI_TMDS_C_DATA1# 7 HDMI_TMDS_C_DATA0 8 GND 9 HDMI_TMDS_C_DATA0# 10 HDMI_TMDS_C_CLK 11 GND 12 HDMI_TMDS_C_CLK# 13 NC 14 NC 15 HDMI_DDC_SCLK 16 HDMI_DDC_SDATA 17 GND 18 +5V_HDMI 19 HDMI_HPD
Table 3-5: HDMI Connector Pinouts
Figure 3-7: HDMI Connector

3.2.8 RS-232 Port for Touch Panel (Reserved for Resistive Touch)

Use the side panel standard RS-232 DB-9 female touch panel connector to connect the
monitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
1 N/A 6 NDSR 2 NRX 7 NRTS 3 NTX 8 N/A
Page 28
4 NDTR 9 N/A 5 GND
Table 3-6: RS-232 Touch Panel Connector Pinouts
DM-F Series Monitor
Figure 3-8: RS-232 Touch Panel Connector
3.2.8.1 Installing RS-232 Connector
If the DM-F series doesn’t have the RS-232 connector on the side panel, the user can
purchase the RS-232 Touch Cable Kit (DM-F-COMKIT-R10) and install the RS-232
connector onto the system. Please note that the RS-232 port is only available for the
resistive type models of the 6.5”–19” monitors.
Step 1: Remove the rear cover retention screws and lift the rear panel off the monitor.
Figure 3-9: Rear Panel Retention Screw Removal (6.5” & 8”)
Page 29
Figure 3-10: Rear Panel Retention Screw Removal (12”–24”)
Step 2: Remove the RS-232 knockout hole on the side panel.
Step 3: Connect the RS-232 flat cable to the internal RS-232 connector (1x9 pin,
DM-F Series Monitor
RS232_1) on the AD board. See Figure 3-11.
Page 30
Figure 3-11: Connecting RS-232 Cable
Step 4: Insert the D-sub 9 connector of the RS-232 flat cable into the hole and secure
the connector with two hex jack screws.
DM-F Series Monitor
Figure 3-12: Hex Jack Screws for Securing RS-232 Connector
Step 5: Re-install the rear panel.

3.3 Mounting the Monitor

The DM-F series LCD monitor can be mounted in a panel, cabinet, rack or wall. The
monitor can also be mounted on a monitor arm or stand. The mounting methods are
described below.
CAUTION:
When mounting the monitor take care to tighten the retention screws or
bolts until fully secure, but do not over tighten. Over tightening the
retention screws or bolts may cause them to become stripped,
rendering them useless.

3.3.1 Panel Mounting

Each model of the DM-F series LCD monitor has a series of mounting slots located on the
top, side and bottom panels for mounting the monitor to a panel.
4Table 3-7 lists the number of mounting clamps and holders required to mount the monitor
to a panel.
Model Mounting Clamps Clamp Holders
DM-F65A 8 N/A
DM-F08A 8 N/A
DM-F12A 9 9
DM-F15A 9 9
Page 31
DM-F17A 9 9
DM-F19A 10 10
DM-F22A 10 10
DM-F24A 12 12
DM-F Series Monitor
Table 3-7: Panel Mounting Clamps
Figure 3-13: Mounting Clamps Holder
Figure 3-14: Mounting Clamps
Page 32
To mount the DM-F series LCD monitor into a panel, please follow the steps below.
Step 1: Select the position on the panel to mount the monitor.
Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of
the monitor. Take care that the panel section that is cut out is smaller than the
overall size of the metal frame that surrounds the monitor but just large enough
for the rear panel of the monitor to fit through.
DM-F Series Monitor
Figure 3-15: DM-F65A Cutout Dimensions (Unit: mm)
Figure 3-16: DM-F08A Cutout Dimensions (Unit: mm)
Figure 3-17: DM-F12A Cutout Dimensions (Unit: mm)
Page 33
DM-F Series Monitor
Figure 3-18: DM-F15A Cutout Dimensions (Unit: mm)
Figure 3-19: DM-F17A Cutout Dimensions (Unit: mm)
Page 34
Figure 3-20: DM-F19A Cutout Dimensions (Unit: mm)
DM-F Series Monitor
Step 3: Secure the mounting clamps holders to the corresponding holes on the rear of
Figure 3-21: DM-F22A Cutout Dimensions (Unit: mm)
Figure 3-22: DM-F24A Cutout Dimensions (Unit: mm)
the monitor (Figure 3-23).
NOTE:
It is not required to install the clamp holders to the DM-F65A and
DM-F08A monitors for panel/rack mounting. After sliding the monitor
through the panel, simply insert the panel mounting clamps into the
pre-formed holes along the top, side and bottom panels of the
monitors. Then, tighten the screws that pass through the panel
mounting clamps until the plastic caps at the front of all the screws are
firmly secured to the panel.
Page 35
Figure 3-23: Secure the Mounting Clamp Holders
DM-F Series Monitor
Step 4: Slide the monitor through the hole until the aluminum frame is flush against the
panel (Figure 3-24).
Page 36
Figure 3-24: Slide into the Panel
DM-F Series Monitor
Step 5: Insert the panel mounting clamps into the pre-formed holes of the clamp holders
(Figure 3-25).
Step 6: T
ighten the screws that pass through the panel mounting clamps until the plastic
caps at the front of all the screws are firmly secured to the panel (Figure 3-25).
Figure 3-25: Panel Mounting Clamp Installation
The dimensions of the clamp holder and the clamp are shown in the following diagrams.
Figure 3-26: Mounting Clamps Holder Dimensions
Page 37
DM-F Series Monitor
Figure 3-27: Ultra Set Plate Dimensions
Figure 3-28: Bolt Dimensions
Figure 3-29: Steering Button Dimensions
Page 38
DM-F Series Monitor

3.3.2 Cabinet and Rack Installation (for F65A ~ F17A)

NOTE:
When purchasing a cabinet/rack installation bracket, make sure it is
compatible with both the monitor and the cabinet/rack into which the
monitor is installed.
The DM-F series LCD monitor can be installed into a cabinet or rack. The installation
procedures are similar to the panel mounting installation. To do this, please follow the
steps below:
Step 1: Secure the mounting clamps holders to the corresponding holes on the rear of
the monitor (Figure 3-30).
NOTE:
It is not required to install the clamp holders to the DM-F65A and
DM-F08A monitors for panel/rack mounting. After sliding the monitor
through the panel, simply insert the panel mounting clamps into the
pre-formed holes along the top, side and bottom panels of the
monitors.
Figure 3-30: Secure the Mounting Clamp Holders
Page 39
Step 2: Slide the rear of the DM-F series LCD monitor through the rack/cabinet bracket
DM-F Series Monitor
until the aluminum frame is flush against the front of the bracket (Figure 3-31).
Figure 3-31: Slide into the Rack/Cabinet Bracket
Step 3: Insert the panel mounting clamps into the pre-formed holes of the clamp holders
(Figure 3-32).
Step 4: T
Figure 3-32: Secure the Rack/Cabinet Bracket
ighten the screws that pass through the rack mounting clamps until the plastic
caps at the front of all the screws are firmly secured to the bracket (Figure 3-3 2).
Page 40
DM-F Series Monitor
Step 5: Slide the LCD monitor with the attached rack/cabinet bracket into a rack or
cabinet (Figure 3-33).
Figure 3-33: Install into a Rack/Cabinet
Step 6: Once the LCD monitor with the attached rack/cabinet bracket has been properly
inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-33).

3.3.3 Cabinet and Rack Installation (for F19A)

NOTE:
When purchasing a cabinet/rack installation bracket, make sure it is
compatible with both the monitor and the cabinet/rack into which the
monitor is installed.
To install the DM-F19A to a cabinet or rack, please follow the steps below:
Step 1: Slide the rear of the DM-F series LCD monitor through the rack/cabinet bracket
until the aluminum frame is flush against the front of the bracket (Figure 3-34).
Page 41
Figure 3-34: Slide DM-F19A into the Rack/Cabinet Bracket
Step 2: Secure the rack/cabinet bracket to the monitor. To do this, secure the 10
DM-F Series Monitor
mounting brackets to the corresponding screw holes on the rear of the monitor using the provided retention screws (Figure 3-35).
Page 42
Figure 3-35: Secure the Mounting Brackets
DM-F Series Monitor
Step 3: Slide the LCD monitor with the attached rack/cabinet bracket into a rack or
cabinet (Figure 3-36).
Figure 3-36: Install DM-F19A into a Rack/Cabinet
Step 4: Once the LCD monitor with the attached rack/cabinet bracket has been properly
inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-33).
Page 43

3.3.4 Wall Mounting

CAUTION:
Due to safety concerns, it is highly recommended to use the VESA
mounting kits provided by IEI for wall, stand and arm mounting. If the
VESA mounting kit is purchased separately, please make sure the
mounting kit is UL-listed.
Each model of the DM-F series LCD monitor has four holes located on the rear panel for
mounting the monitor to a wall. To mount the DM-F series LCD monitor onto a wall, please
follow the steps below.
Step 1: Attach the wall mounting kit to the mounting surface with the included screws.
DM-F Series Monitor
Make sure it is attached securely (
5Figure 3-37).
Figure 3-37: Attach Wall Mounting Kit to the Wall
Step 2: Screw the mounting screws to the mounting holes on the rear of the DM-F series
Page 44
(Figure 3-38).
Step 3: Hoo
(Figure 3-38).
k the DM-F series into the mounting holes on the wall mounting kit
DM-F Series Monitor
Figure 3-38: Hook Onto Wall Mounting Kit
Step 4: Tighten the top screw on the wall mounting kit to securely hold the DM-F series
in place. After this screw is tightened, the DM-F series should not be able to
move.
Figure 3-39: Tighten Retention Screw
Page 45

3.3.5 Stand Installation

The DM-F series LCD monitor has Video Electronics Standards Association (VESA)
standard mounting holes tapped into the rear panel. The standard holes are M4 set at
75 mm x 75 mm or 100 mm x 100 mm apart (Figure 3-40 and Figure 3-41).
DM-F Series Monitor
Figure 3-40: VESA Mounting Holes (6.5” & 8”)
Figure 3-41: VESA Mounting Holes (12”–24”)
Page 46
DM-F Series Monitor
To mount the DM-F series LCD monitor onto a stand, please follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor stand mounting plate.
Step 2: Secure the monitor to the stand with the supplied retention screws (
Figure 3-42: Monitor Stand Mounting
5Figure 3-42).

3.3.6 Arm Installation

The DM-F series LCD monitor has VESA standard mounting holes tapped into the rear
panel. The standard holes are M4 set at 75 mm x 75 mm or 100 mm x 100 mm apart
(Figure 3-40 and Figure 3-41). To mount the DM-F series
please follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor arm mounting plate.
Step 2: Secure the monitor to the arm with the supplied retention screws (Figure 3-43).
Step 0:
LCD monitor onto a monitor arm,
Page 47
DM-F Series Monitor
Figure 3-43: Monitor Arm Mounting
Page 48
DM-F Series Monitor
Chapter
4
4 On-Screen-Display (OSD)
Controls
Page 49

4.1 OSD Keypad

There are several on-screen-display (OSD) control buttons of the OSD keypad on the
monitor rear panel. Figure 4-1 shows the 5-key membrane OSD keypad of the 6.5”and 8”
DM-F Series Monitor
LCD monito
rs.
Figure 4-1: OSD Keypad for 6.5” and 8” Monitors
Page 50
The function of each button is described in the following table.
LCD ON/OFF Press this button to turn on or turn off the LCD screen.
AUTO
LEFT
RIGHT
MENU
Press this button to automatically adjust the screen. When inside a menu, press this button to confirm the selection o f the item. Press this button to decrease the value, or to scroll up from one selected item to another. Press this button to increase the value, or to scroll down from one selected item to another. Press this button to open the OSD window, exit the main menu or the current menu.
Table 4-1: OSD Control Buttons for 6.5” and 8” Monitors
DM-F Series Monitor
Figure 4-2 shows the 7-key membrane OSD keypad of the 12”–24” LCD monitors.
Figure 4-2: OSD Keypad for 12”–24” Monitors
The function of each button is described in the following table.
LCD on/off Press this butto n to turn on or turn off the LCD screen. Auto Press this button to automatically adjust the screen.
Menu
Left
Right Press this button to decrease the value. Up Press this button to scroll up from one selected item to another. Down Press this button to scroll down from one selected item to another.
Press this button to open the OSD window, exit the main menu or the current menu. Press this button to increase the value. When inside a menu, press this button to enter the submenu or confirm the selection of the item.
Table 4-2: OSD Control Buttons for 12”–24” Monitors
Page 51

4.2 OSD Menu Structure

5Table 4-3 shows the OSD menu structure for all models of the DM-F series LCD monitor.
Level 0 Level 1 Level 2 Value
DM-F Series Monitor
Image
Display
System
Brightness 0 to 100 Contrast 0 to 100 Sharpness -4 to 4 Color
Auto Adjust Phase 0 to 100 Clock 0 to 100 Display Position Display Modes
Input
Auto Color temp
Display Port
5000K 6500K 9300K User Reset
Gamma off Gamma 2.2
OSD Setting
Information Reset
Table 4-3: OSD Menu Structure
Page 52
VGA DVI/HDMI autoscan Timer 10sec/30sec/60sec Rotation 0°/90°/180°/270° Position Transparency 0 to 100
DM-F Series Monitor

4.3 Using the OSD

OSD menu options are described below.

4.3.1 Image Menu

Image menu features are shown in Figure 4-3.
Figure 4-3: Image Menu
The brightness option adjusts the brightness of screen. This function
Brightness
Contrast
Sharpness
Color
adjusts the offset value of ADC. Setting this value too high or too low
will affect the quality of image.
This function adjusts the gain value of ADC. Adjusting this value too
high or too low will worsen the quality of image.
Adjusts the sharpness level. This option softens the edges around
objects on the screen.
Provides options for color settings. (Figure 4-4)
Page 53
4.3.1.1 Color Setting
Color settings are shown in Figure 4-3.
DM-F Series Monitor
Figure 4-4: Color Settings
auto
Color temp
Automatically adjusts the color settings.
This item allows adjustment of the following items.
5000k – NTSC standard Kelvin
6500k – NTSC standard Kelvin
9300k – NTSC standard Kelvin
User – This item allows fine-tuning the balance among Red,
Green, and Blue color hues if images look garish or unrealistic.
Page 54
DM-F Series Monitor

4.3.2 Display Menu

Display menu features are shown in Figure 4-5.
Figure 4-5: Display Menu
Auto Adjust
Phase
Clock
Display Position
Display Mode
Automatically adjusts the LCD screen position.
Adjusts the phase control of image
Adjusts frequency to fill display
Adjusts the horizontal and vertical position of the display screen
This item allows adjustment of the Gamma.
Page 55

4.3.3 System Menu

System menu features are shown in Figure 4-6.
DM-F Series Monitor
Figure 4-6: System Menu
Input
OSD Setting
Information
Reset
Allows selection of input device to use. (Figure 4-7)
Provides options for OSD configuration. (Figure 4-8)
s
Provide
release date and input resolution.
Restores the default OSD settings. Note that this will restore all default
display settings.
s information on the LCD monitor, such as firmware version,
Page 56
DM-F Series Monitor
4.3.3.1 Input
Input options are shown in Figure 4-7.
Figure 4-7: Input Options
Input options are described below.
Display Port
VGA
HDMI
autoscan
This item sets the input device to display port.
This item sets the input device to VGA.
This item sets the input device to HDMI.
Selects the input device to use automatically.
Page 57
4.3.3.2 OSD Settings
The OSD settings are shown in Figure 4-8.
DM-F Series Monitor
Figure 4-8: OSD Settings Menu
OSD settings are described below.
Timer
Rotation
Position
Transparency
Determines how many seconds the OSD screen stays on screen
before it disappears when OSD is left unattended.
Adjusts the OSD rotation angle on the screen.
Adjusts the OSD position on the screen.
Adjust the transparency of the OSD menu background.
Page 58
DM-F Series Monitor
Chapter
5

5 Software Drivers

Page 59

5.1 Introduction

The touch panel controller enables analog resistive touch panels for four-wire, five-wire &
eight-wire models. The controller directly communicates with the PC system through the
touch panel communications interface. The controller design is superior in sensitivity,
accuracy, and friendly operation. The touch panel driver emulates the left mouse button
and the right mouse button functions.
The touch panel driver supports the following operating systems:
DM-F Series Monitor
Microsoft
o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft o Microsoft
Microsoft
o Microsoft o Microsoft o Microsoft
Linux Kernel 2.6
DOS
Driver installation is described below.
®
Windows® versions:
®
Windows® 2000
®
Windows® XP
®
Windows® 2003
®
Windows® 2008
®
Windows® Vista
®
Windows® 7
®
Windows® 8
®
Windows® CE versions:
®
Windows® CE 4.2
®
Windows® CE 5.0
®
Windows® CE 6.0

5.2 RS-232 or USB Touchscreen

Before installing the driver, connect the DM-F series monitor to the motherboard. The
DM-F series monitors support touchscreen modality through a USB or an RS-232
interface connection. Decide through which interface the touchscreen is to be controlled.
Page 60
DM-F Series Monitor
NOTE:
The default touchscreen interface for the DM-F series monitor is USB
interface. The RS-232 interface is only reserved for the models with
resistive type touchscreen.
RS-232 Interface: If the touchscreen interface connection is an RS-232
connection, connect the RS-232 connector on the single board computer to
the DB-9 connector of the DM-F series monitor.
USB Interface: If the touchscreen interface connection is a USB connection,
connect the USB connector on the single board computer to the external USB
port connector of the DM-F series monitor.

5.3 Touch Panel Driver Installation

WARNING:
Before the touchscreen driver is installed, make sure the system is
connected to the monitor with a USB cable or an RS-232 null cable.
Also, make sure the VGA connector on the system is connected to the
VGA connector on the bottom of the monitor.
To install the touch panel driver for the DM-F series, please follow the instructions below:
Step 1: Connect the DM-F series monitor to the single board computer. See above.
Step 2: Install the driver CD. Install the driver CD into the system to which the DM-F
series monitor is connected.
Step 3: Select the Touch Screen option in the menu of driver CD. The directory in
Figure 5-1 a
ppears.
Page 61
DM-F Series Monitor
Figure 5-1: Setup Icon
Step 4: Double click the setup icon in Figure 5-1.
Step 5: The W
Figure 5-2: Welcome Screen
Step 6: Click Next to continue.
elcome screen in Figure 5-2 app
ears.
Page 62
Step 7: The license agreement in Figure 5-3 a
agreement by clicking I Agree.
ppears. Accept the terms of the
DM-F Series Monitor
Figure 5-3: License Agreement
Step 8: The installation destination screen appears. See Figure 5-4. C
Figure 5-4: Initiate Install
Step 9: The installation of the program begins. See Figure 5-5.
lick Install.
Page 63
DM-F Series Monitor
Figure 5-5: Installation Starts
Step 10: When the installation is complete, the complete screen appears. See Figure 5-6.
T
o complete the installation process click Finish.
Figure 5-6: Finish Installation
Page 64
DM-F Series Monitor

5.4 Change the Touchscreen Interface

If the touchscreen interface must be changed from a USB interface to an RS-232 interface
or from an RS-232 interface to a USB interface, the following steps must be followed.
Step 1: Uninstall the touchscreen driver
Step 2: Remove the interface cable i.e. remove the USB cable or the RS-232 cable
Step 3: Install the new cable i.e. install the RS-232 cable or the USB cable.
Step 4: Reinstall the driver CD as described above. Step 0:

5.5 Calibrating the Touchscreen

To calibrate the touchscreen cursor with the motion of the touch pen (or finger), please
follow the steps below:
Step 1: Make sure the system is properly connected through a USB or an RS-232
interface to the DM-F series monitor.
Step 2: Make sure the touchscreen driver is properly installed.
Step 3: Locate the PenMount Monitor icon in the bottom right corner of the screen.
Figure 5-7: PenMount Monitor Icon
Step 4: Click the icon. A pop up menu appears. See Figure 5-8.
Page 65
Figure 5-8: PenMount Monitor Popup Menu
Step 5: Click Control Panel in the pop up menu shown in Figure 5-8.
DM-F Series Monitor
Step 6: The co
Figure 5-9: Configuration Screen
nfiguration screen in Figure 5-9 a
ppears.
Page 66
Step 7: Double click the PenMount 6000 icon as shown in Figure 5-9.
Step 8: The cali
Step 9: Select the Standard Calibration button as shown in Figure 5-10.
bration initiation screen in Figure 5-10 ap
pears.
DM-F Series Monitor
Figure 5-10: Calibration Initiation Screen
Step 10: The calibration screen in is shown. See Figure 5-11.
Figure 5-11: Calibration Screen
Step 11: Follow the instructions. The user is asked touch the screen at five specified
points after which the screen is calibrated. Step 0:
Page 67
DM-F Series Monitor
Chapter
6

6 AD Boards

Page 68
DM-F Series Monitor

6.1 AD Board Overview

The DM series LCD monitor AD board provides a wide variety of control interfaces. There
are two AD boards used for the DM series monitors: AV-6038 and AV-60381. Refer to
5Table 1-2 for a listing of DM series monitors and their associated AD board. The following
sections describe each AD board in detail.

6.2 A V-6038 AD Board

The connector locations of the AV-6038 are shown in Figure 6-1. The Pin 1 locations of
the on-board connectors are also indicated in the diagrams below. The connector pinouts
for these connectors are listed in the following sections.
Figure 6-1: AV-6038 AD Board Layout Diagram
Page 69

6.2.1 AV-6038 Peripheral Interface Connectors

5Table 6-1 shows a list of the peripheral interface connectors on the AV-6038 AD board.
Pinouts of the connectors that are used in the DM-F series can be found in the following
sections.
Connector Type Label
Backlight Inverter connector 6-pin wafer, p=2.00 mm INVERTER1
COM debug port connector 2-pin wafer, p=2.00 mm CN2
Camera connector 4-pin wafer, p=1.25 mm USB_CAM1
DisplayPort firmware connector 4-pin wafer, p=1.25 mm DP_FW1
HDMI firmware connector 4-pin wafer, p=1.25 mm HDMI_FW1
DM-F Series Monitor
Infrared connector 2-pin wafer, p=2.00 mm CN3
LVDS connector 30-pin crimp, p=1.25 mm LVDS1
OSD keypad connector 12-pin wafer, p=1.00 mm CN14
Power input connector 4-pin wafer, p=3.96 mm CN9
RS-232 connector for touchscreen 6-pin wafer, p=1.25 mm RS232_1
SPI flash connector 6-pin wafer, p=1.25 mm JSPI1
USB connector for touchscreen 4-pin wafer, p=1.25 mm USB_TOUCH1
Touchscreen connector 9-pin wafer, p=1.25 mm J1
Jumper Type Label
LVDS panel voltage select jumper 6-pin header, p=2.54 mm JP2
EIDE firmware update jumper 2-pin header, p=2.00 mm JP3
Table 6-1: AV-6038 Peripheral Interface Connectors
Page 70
DM-F Series Monitor

6.2.2 Backlight Inverter Connector (INVERTER1)

PIN NO. DESCRIPTION
1 BKL_POWER1 2 BKL_POWER1 3 ENABKL 4 BRIGHTNESS 5 GND 6 GND
Table 6-2: Backlight Inverter Connector (INVERTER1) Pinouts

6.2.3 LVDS Connector (LVDS1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 GND 3 A0P_C 4 A0M_C 5 A1P_C 6 A1M_C 7 A2P_C 8 A2M_C 9 CLK1P_C 10 CLK1M_C 11 A3P_C 12 A3M_C 13 GND 14 GND 15 A4P_C 16 A4M_C 17 A5P_C 18 A5M_C 19 A6P_C 20 A6M_C 21 CLK2P_C 22 CLK2M_C 23 A7P_C 24 A7M_C 25 GND 26 GND 27 VCC 28 VCC 29 VCC 30 VCC
Table 6-3: LVDS Connector (LVDS1) Pinouts
Page 71

6.2.4 OSD Keypad Connector (CN14)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V_OSD 2 +12V
3 OSD1 4 OSD2 5 OSD3 6 OSD4 7 OSD5 8 OSD6 9 OSD7 10 MLED8 11 GND 12 +3.3V_DVDD
Table 6-4: OSD Keypad Connector (CN14) Pinouts

6.2.5 Power Input Connector (CN9)

PIN NO. DESCRIPTION
DM-F Series Monitor
1 GND 2 GND 3 VCC 4 VCC
Table 6-5: Power Input Connector (CN9) Pinouts

6.2.6 RS-232 Connector for Touchscreen (RS232_1)

PIN NO. DESCRIPTION
1 NDSR 2 NRX 3 NRTS 4 NTX 5 NDTR 6 GND
Table 6-6: RS-232 Connector for Touchscreen (RS232_1) Pinouts
Page 72
DM-F Series Monitor

6.2.7 USB Connector for Touchscreen (USB_TOUCH1)

PIN NO. DESCRIPTION
1 VCC_TOUCH 2 D2F­3 D2F+ 4 GND
Table 6-7: USB Connector for Touchscreen (USB_TOUCH1) Pinouts

6.2.8 Touchscreen Connector (J1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 X+ 2 X-
3 Y+ 4 SENSE 5 X+ 6 X­7 Y+ 8 Y+ 9 GND
Table 6-8: Touchscreen Connector (J1) Pinouts

6.2.9 LVDS Panel Voltage Select Jumper (JP2)

DESCRIPTION
Short 1-2 +3.3 V (for 12” and 15”) Short 3-4 +5 V (for 17”, 19”, 21.5” and 24”) Short 5-6 NC
Table 6-9: LVDS Panel Voltage Select Jumper (JP2) Pinouts

6.2.10 EIDE Firmware Update Jumper (JP3)

DESCRIPTION
1 EDID_WP 2 GND
Table 6-10: EIDE Firmware Update Jumper (JP3) Pinouts
Page 73

6.3 A V-60381 AD Board

The connector locations of the AV-60381 are shown in Figure 6-1. The Pin 1 locations of
the on-board connectors are also indicated in the diagrams below. The connector pinouts
for these connectors are listed in the following sections.
DM-F Series Monitor
Figure 6-2: AV-60381 AD Board Layout Diagram

6.3.1 AV-60381 Peripheral Interface Connectors

5Table 6-11 shows a list of the peripheral interface connectors on the AV-60381 AD board.
Pinouts of the connectors that are used in the DM-F series can be found in the following
sections.
Connector Type Label
Auto dimming connector 6-pin wafer, p=1.25 mm CN4
Backlight Inverter connector 6-pin wafer, p=2.00 mm INVERTER1
COM debug port connector 2-pin wafer, p=2.00 mm CN2
LVDS connector 30-pin crimp, p=1.25 mm LVDS1
OSD keypad connector 12-pin wafer, p=1.00 mm KEYPAD1
Page 74
DM-F Series Monitor
Power input connector 3-pin wafer, p=3.96 mm PWR2
Power input connector (+12 V) 2-pin wafer, p=2.00 mm CN15
Power output connector 2-pin wafer, p=2.00 mm CN16
RS-232 connector for touchscreen 6-pin wafer, p=1.25 mm RS232_1
SPI flash connector 6-pin wafer, p=1.25 mm JSPI1
USB connector for touchscreen 4-pin wafer, p=1.25 mm USB_TOUCH1
Touchscreen connector 9-pin wafer, p=1.25 mm J1
VGA connector 10-pin box header, p=2.00 mm VGA2
Jumper Type Label
Backlight voltage select jumper 6-pin header, p=2.54 mm JP5
LVDS panel voltage select jumper 6-pin header, p=2.54 mm JP2
Power input setting jumper 6-pin header, p=2.54 mm JP4
Touchscreen type select jumper 2-pin header, p=2.00 mm JP1
Table 6-11: AV-60381 Peripheral Interface Connectors

6.3.2 Backlight Inverter Connector (INVERTER1)

PIN NO. DESCRIPTION
1 BKL_POWER1 2 BKL_POWER1 3 ENABKL 4 BRIGHTNESS 5 GND 6 GND
Table 6-12: Backlight Inverter Connector (INVERTER1) Pinouts
Page 75

6.3.3 LVDS Connector (LVDS1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 GND 3 A0P_C 4 A0M_C 5 A1P_C 6 A1M_C 7 A2P_C 8 A2M_C 9 CLK1P_C 10 CLK1M_C 11 A3P_C 12 A3M_C 13 GND 14 GND 15 A4P_C 16 A4M_C 17 A5P_C 18 A5M_C 19 A6P_C 20 A6M_C 21 CLK2P_C 22 CLK2M_C
DM-F Series Monitor
23 A7P_C 24 A7M_C 25 GND 26 GND 27 VCC 28 VCC 29 VCC 30 VCC
Table 6-13: LVDS Connector (LVDS1) Pinouts

6.3.4 OSD Keypad Connector (KEYPAD1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V_OSD(NC) 2 +12V(NC)
3 Left 4 Auto 5 Right 6 Power 7 Menu 8 Led_GREED (UP) 9 Down (NC) 10 Led_RED 11 GND 12 +3.3V_DVDD(NC)
Table 6-14: OSD Keypad Connector (KEYPAD1) Pinouts
Page 76
DM-F Series Monitor

6.3.5 Power Input Connector (PWR2)

PIN NO. DESCRIPTION
1 +9 V ~ +36 V to external power module 2 GND 3 +12 V input
Table 6-15: Power Input Connector (PWR2) Pinouts

6.3.6 RS-232 Connector for Touchscreen (RS232_1)

PIN NO. DESCRIPTION
1 NDSR 2 NRX 3 NRTS 4 NTX 5 NDTR 6 GND
Table 6-16: RS-232 Connector for Touchscreen (RS232_1) Pinouts

6.3.7 USB Connector for Touchscreen (USB_TOUCH1)

PIN NO. DESCRIPTION
1 VCC_TOUCH 2 D2F­3 D2F+ 4 GND
Table 6-17: USB Connector for Touchscreen (USB_TOUCH1) Pinouts

6.3.8 Touchscreen Connector (J1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 X+ 2 X-
3 Y+ 4 SENSE 5 X+ 6 X-
Page 77
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
7 Y+ 8 Y+ 9 GND
Table 6-18: Touchscreen Connector (J1) Pinouts

6.3.9 VGA Connector (VGA2)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 SMCLK
3 GREEN 4 SMDATA 5 BLUE 6 GND 7 H-SYNC 8 GND 9 V-SYNC 10 GND
Table 6-19: VGA Connector (VGA2) Pinouts
DM-F Series Monitor

6.3.10 Backlight Voltage Select Jumper (JP5)

DESCRIPTION
Short 1-2 +3.3 V Short 3-4 +5 V Short 5-6 +12 V
Table 6-20: Backlight Voltage Select Jumper (JP5) Pinouts

6.3.11 LVDS Panel Voltage Select Jumper (JP2)

DESCRIPTION
Short 1-2 +3.3 V (for 6.5” and 8”) Short 3-4 +5 V Short 5-6 NC
Table 6-21: LVDS Panel Voltage Select Jumper (JP2) Pinouts
Page 78
DM-F Series Monitor

6.3.12 Power Input Setting Jumper (JP4)

DESCRIPTION
Short 1-3, 2-4 +12 V from power jack (PRW1)
Short 3-5, 4-6
Input with external connector (external power module is needed)
Table 6-22: Power Input Setting Jumper (JP4) Pinouts

6.3.13 Touchscreen Type Select Jumper (JP1)

DESCRIPTION
1 5-wire touchscreen 2 4-wire/8-wire touchscreen
Table 6-23: Touchscreen Type Select Jumper (JP1) Pinouts
Page 79
DM-F Series Monitor
Appendix
A

A Regulatory Compliance

Page 80
DM-F Series Monitor
DECLARATION OF CONFORMITY
This equipment has been tested and found to comply with specifications for CE marking.
If the user modifies and/or installs other devices in the equipment, the CE conformity
declaration may no longer apply.
FCC WARNING
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Page 81
DM-F Series Monitor
Appendix
B

B Safety Precautions

Page 82
DM-F Series Monitor
WARNING:
The precautions outlined in this chapter should be strictly followed.
Failure to follow these precautions may result in permanent damage to
the DM-F Series.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.
Follow the electrostatic precautions outlined below whenever the DM-F
Series is opened.
Make sure the power is turned off and the power cord is disco nnected
whenever the DM-F Series is being installed, moved or modified.
Do not apply voltage levels that exceed the specified voltage range.
Doing so may cause fire and/or an electrical shock.
Electric shocks can occur if the DM-F Series chassis is opened when the
DM-F Series is running.
Do not drop or insert any objects into the ventilation openings of the DM-F
Series.
If considerable amounts of dust, water, or fluids enter the DM-F Series,
turn off the power supply immediately, unplug the power cord, and contact the
DM-F Series vendor.
DO NOT:
o Drop the DM-F Series against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature
Page 83

B.1.2 Anti-static Precautions

WARNING:
Failure to take ESD precautions during the installation of the DM-F
Series may result in permanent damage to the DM-F Series and severe
injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the DM-F Series. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the DM-F Series is opened and any of the electrical components are
handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
DM-F Series Monitor
help to prevent ESD from damaging any electrical component.
Self-grounding: Before handling any electrical component, touch any
grounded conducting material. During the time the electrical component is
handled, frequently touch any conducting materials that are connected to the
ground.
Use an anti-static pad: When configuring or working with an electrical
component, place it on an antic-static pad. This reduces the possibility of ESD
damage.
Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
Page 84
Loading...