IEI Technology DM-150GS/R-R30, DM-150GMS/R-R30, DM-170GS/R-R30, DM-170GMS/R-R30, DM-190GS/R-R30 User Manual

...
DM Series Monitor
Page I
IEI Technology Co rp.
User Manual
MODEL:
DM Series
15”~19” LCD Monitor
VGA/DVI-D, IP 65 Protection, RoHS
Re v. 3.00 – 7 June , 2013
DM Series Monitor
Page II
Revision
Date Version Changes
7 June, 2013 3.00 Initial Release
DM Series Monitor
Page III
Copyright
COP YRIGHT NOTICE
The information in this document is subject to change without prior notice in order to improve rel iabilit y, design and funct ion and d oes not r epresent a com mitm ent on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, e lectronic, or other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered tradem ark s and produc t nam es ment ioned here in are us ed for identif icatio n purposes only and m ay be trademarks and/or registe red trademarks of their respective owners.
DM Series Monitor
Page IV
Table of Contents
1 INTRODUCTION .......................................................................................................... 1
1.1 OVERVIEW .................................................................................................................. 2
1.2 FEATURES ................................................................................................................... 2
1.3 MODEL VARIATIONS ................................................................................................... 3
1.4 APPLICATIONS ............................................................................................................ 3
1.5 EXTERNAL OVERVIEW ................................................................................................ 4
1.5.1 Front View .......................................................................................................... 4
1.5.2 Bottom Panel View ............................................................................................. 5
1.5.3 AD Board ........................................................................................................... 6
1.6 SERIES SPECIFICATIONS .............................................................................................. 7
1.7 CERTIFICATIONS ......................................................................................................... 8
2 MECHANICAL OVERVIEW ...................................................................................... 9
2.1 INTRODUCTION ......................................................................................................... 10
2.2 FRONT PANEL ........................................................................................................... 10
2.2.1 Front Panel Variants ........................................................................................ 10
2.2.2 Front Panel Variant 1 ....................................................................................... 10
2.2.3 Front Panel Variant 2 ........................................................................................ 11
2.2.4 Bottom Panel .................................................................................................... 12
2.2.5 A vailable Connectors ....................................................................................... 12
2.3 PHYSICAL DIMENSIONS ............................................................................................ 13
2.3.1 General Physical Dimensions .......................................................................... 13
2.3.2 DM-150 Physical Dimensions ......................................................................... 14
2.3.3 DM-170 Physical Dimensions ......................................................................... 15
2.3.4 DM-190 Physical Dimensions ......................................................................... 16
2.3.5 Optional Mounting Kits ................................................................................... 17
2.3.6 DM-150 Mounting Kits .................................................................................... 17
2.3.7 DM-170 Mounting Kits .................................................................................... 17
2.3.8 DM-190 Mounting Kits .................................................................................... 18
3 LCD SPECIFICATIONS ............................................................................................ 19
DM Series Monitor
Page V
3.1 LCD SPECIFICATIONS ............................................................................................... 20
3.1.1 LCD Overview ................................................................................................. 20
3.1.2 DM-150 LCD Specifications ............................................................................ 20
3.1.3 DM-170 LCD Specifications ............................................................................ 21
3.1.4 DM-190 LCD Specifications ............................................................................ 21
4 AD BOARD ................................................................................................................... 23
4.1 AD BOARD OVERVIEW ............................................................................................. 24
4.2 AV-6600 AD BOARD OVERVIEW .............................................................................. 24
4.2.1 AV-6600 Peripheral Interface Connectors ....................................................... 24
4.2.2 AV-6600 Rear Panel Connectors ..................................................................... 25
5 INSTALLATION ......................................................................................................... 26
5.1 INSTALLATION PRECAUTIONS ................................................................................... 27
5.2 UNPACKING .............................................................................................................. 28
5.2.1 Packaging ........................................................................................................ 28
5.2.2 Unpacking Procedure ...................................................................................... 28
5.2.3 Packing List ..................................................................................................... 29
5.3 PRE-INSTALLATION PREPARATION ............................................................................ 29
5.3.1 Tools ................................................................................................................. 29
5.3.2 Voltage Select Jumper Settings ........................................................................ 30
5.4 CONNECTORS ........................................................................................................... 31
5.4.1 Rear Panel Connectors Overview .................................................................... 31
5.4.2 VGA Connector ................................................................................................ 32
5.4.3 DVI-D Connector ............................................................................................. 32
5.4.4 12V Power Connector ...................................................................................... 33
5.4.5 RS-232 for Touch Panel Connector ................................................................. 33
5.4.6 USB for Touch Panel Connector ...................................................................... 34
5.4.7 Optional Terminal Block .................................................................................. 34
5.5 MOUNTING THE MONITOR ........................................................................................ 35
5.5.1 Panel Mounting ................................................................................................ 35
5.5.2 Cabinet and Rack Installation ......................................................................... 38
5.5.2.1 Standard Cabinet and Rack Installation .................................................... 39
5.5.2.2 DM-190 Cabinet and Rack Installation .................................................... 41
5.5.3 Wall Mounting .................................................................................................. 43
DM Series Monitor
Page VI
5.5.4 Monitor Stand Installation ............................................................................... 45
5.5.5 Monitor Arm Installation ................................................................................. 47
6 ON-SCREEN-DISPLAY (OSD) CONTROLS .......................................................... 48
6.1 USER MODE OSD STRUCTURE ................................................................................. 49
6.1.1 OSD Buttons ..................................................................................................... 49
6.1.2 OSD Menu Structure ........................................................................................ 50
6.2 USING THE OSD ....................................................................................................... 51
6.2.1 Main Display Features ..................................................................................... 51
6.2.2 Color ................................................................................................................ 52
6.2.3 OSD Configurations ......................................................................................... 53
7 SOFTWARE DRIVERS .............................................................................................. 54
7.1 INTRODUCTION ......................................................................................................... 55
7.2 RS-232 OR USB TOUCH SCREEN ............................................................................. 55
7.3 TOUCH PANEL DRIVER INSTALLATION ...................................................................... 56
7.4 CHANGE THE TOUCH SCREEN INTERFACE ................................................................ 59
7.5 CALIBRATING THE TOUCH SCREEN ........................................................................... 59
8 GASKET REPLACEMENT ....................................................................................... 62
8.1 GASKET REPLACEMENT ........................................................................................... 63
A SAFETY PRECAUTIONS ......................................................................................... 64
A.1 SAFETY PRECAUTIONS ............................................................................................ 65
A.1.1 General Safety Precautions ............................................................................. 65
A.1.2 Anti-static Precautions .................................................................................... 66
A.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 66
A.2.1 Maintenance and Cleaning .............................................................................. 66
A.2.2 Cleaning T ools ................................................................................................. 67
B CERTIFICATIONS .................................................................................................... 68
B.1 ROHS COMPLIANT .................................................................................................. 69
B.2 IP 65 COMPLIANT FRONT PANEL ............................................................................. 69
C SMARTOSD ................................................................................................................ 70
C.1 IEI SMARTOSD QUICK INSTALLATION GUIDE ......................................................... 71
C.2 PRE-INSTALLATION NOTICE ..................................................................................... 71
DM Series Monitor
Page VII
C.3 SMARTOSD INSTALL ............................................................................................... 71
C.4 SOFTWARE ILLUSTRATION ....................................................................................... 75
C.4.1 Manage Page ................................................................................................... 77
C.4.2 EDID Page ...................................................................................................... 78
C.4.3 Image Page ...................................................................................................... 79
C.4.4 Display Page (for analog signal) .................................................................... 80
C.4.5 Color Page ...................................................................................................... 81
C.4.6 PIP Page .......................................................................................................... 82
C.4.7 System Page ..................................................................................................... 83
C.4.8 About Page ...................................................................................................... 84
C.5 SMARTOSD FAQ ..................................................................................................... 85
C.5.1 Windows 2000 Installation Failure ................................................................. 85
C.5.2 Vista Installation Failure ................................................................................. 85
C.5.3 Model Failure .................................................................................................. 86
C.5.4 DCC Port Failure ............................................................................................ 87
DM Series Monitor
Page VIII
List of Figures
Figure 1-1: DM Series ..................................................................................................................... 2
Figure 1-2: Typical Monitor Front View
........................................................................................ 5
Figure 1-3: Bottom Panel View
...................................................................................................... 5
Figure 1-4: AV-6600 AD Board
...................................................................................................... 6
Figure 2-1: Front Panel Variant 1
................................................................................................11
Figure 2-2: Front Panel Variant 2
................................................................................................12
Figure 2-3: DM-150 Physical Dimensions (millimeters)
............................................................14
Figure 2-4: DM-170 Physical Dimensions (millimeters)
............................................................15
Figure 2-5: DM-190 Physical Dimensions (millimeters)
............................................................16
Figure 4-1: AV-6600 AD Board Overview
...................................................................................24
Figure 5-1: Monitor Rear Panel Connec tions
............................................................................31
Figure 5-2: VGA Connector
.........................................................................................................32
Figure 5-3: DVI-D Connector
.......................................................................................................33
Figure 5-4: 12V Power Connector
...............................................................................................33
Figure 5-5: RS-232 Touch Panel Connector
..............................................................................34
Figure 5-6: USB Touch Panel Connector
...................................................................................34
Figure 5-7: Terminal Block
..........................................................................................................35
Figure 5-8: DM-150 Panel Opening (Unit: mm)
..........................................................................36
Figure 5-9: DM-170 Panel Opening (Unit: mm)
..........................................................................36
Figure 5-10: DM-190 Panel Opening (Unit: mm)
........................................................................37
Figure 5-11: Insert the Monitor
....................................................................................................37
Figure 5-12: Panel Mounting Clamp Position
............................................................................38
Figure 5-13: Secure the Cabinet/Rack Bracket
..........................................................................40
Figure 5-14: Install into a Cabinet/Rack
.....................................................................................40
Figure 5-15: Rack Mounting Nuts and Bolts Installation (DM-190)
.........................................41
Figure 5-16: Rack Mounting Bracket Installation (DM-190)
......................................................42
Figure 5-17: Rack Mounting (DM-190)
........................................................................................42
Figure 5-18: Wall-mounting Bracket
...........................................................................................43
Figure 5-19: Monitor Support Screws
.........................................................................................44
Figure 5-20: Wall Mounting the Monitor
.....................................................................................45
DM Series Monitor
Page IX
Figure 5-21: VESA Mounting Holes ............................................................................................46
Figure 5-22: Monitor Stand Mounting
.........................................................................................46
Figure 5-23: Monitor Arm Mounting
............................................................................................47
Figure 6-1: OSD Control Buttons
................................................................................................49
Figure 6-2: Main Display Features
..............................................................................................51
Figure 6-3: Color Options
............................................................................................................52
Figure 6-4: OSD Configurations Menu
.......................................................................................53
Figure 7-1: Setup Icon
..................................................................................................................56
Figure 7-2: Welcome Screen
.......................................................................................................57
Figure 7-3: License Agreement
...................................................................................................57
Figure 7-4: Initiate Install
.............................................................................................................58
Figure 7-5: Installation Starts
......................................................................................................58
Figure 7-6: Finish Installation
......................................................................................................59
Figure 7-7: PenMount Monitor Icon
............................................................................................60
Figure 7-8: PenMount Monitor Popup Menu
..............................................................................60
Figure 7-9: Configuration Screen
................................................................................................60
Figure 7-10: Calibration Initiation Screen
..................................................................................61
Figure 7-11: Calibration Screen
..................................................................................................61
Figure 8-1: Gasket Replacement
.................................................................................................63
Figure 8-2: smartOSD Installer
....................................................................................................72
Figure 8-3: smartOSD Welcome Screen
.....................................................................................72
Figure 8-4: smartOSD Folder Select Screen
..............................................................................73
Figure 8-5: smartOSD Confirm Installati o n
................................................................................73
Figure 8-6: smartOSD Installation Prog ress
..............................................................................74
Figure 8-7: smartOSD Installation Complete
.............................................................................74
Figure 8-8: Manage Page
.............................................................................................................77
Figure C-9: DLL Missing ..............................................................................................................85
Figure C-10: Windows Vista Error
..............................................................................................85
Figure C-11: Install as Administrator
..........................................................................................86
Figure C-12: Firmware Incompatibility
.......................................................................................86
Figure C-13: DCC Port Fai lure
.....................................................................................................87
DM Series Monitor
Page X
List of Tables
Table 1-1: DM Series Model Variations ........................................................................................ 3
Table 1-2: DM Series Specifications
............................................................................................. 8
Table 2-1: Front Panel Variants
...................................................................................................10
Table 2-2: General Physical Dimensions
...................................................................................13
Table 2-3: DM-150 Mounting Kits
................................................................................................17
Table 2-4: DM-170 Mounting Kits
................................................................................................18
Table 2-5: DM-190 Mounting Kits
................................................................................................18
Table 3-1: DM-150 LCD Specifications
.......................................................................................20
Table 3-2: DM-170 LCD Specifications
.......................................................................................21
Table 3-3: DM-190 LCD Specifications
.......................................................................................22
Table 4-1: AV-6600 Peripheral Interface Con ne ct or s
................................................................25
Table 4-2: AV-6600 Rear Panel Connectors
...............................................................................25
Table 5-1: Rear Panel Connectors
..............................................................................................31
Table 5-2: VGA Connector Pinouts
.............................................................................................32
Table 5-3: DVI-D Connector Pinouts
...........................................................................................33
Table 5-4: RS-232 Touch Panel Connector Pinouts
..................................................................33
Table 5-5: USB Touch Panel Connector Pinouts
......................................................................34
Table 5-6: Panel Mounting Clamps
.............................................................................................35
Table 6-1: OSD Menus
..................................................................................................................50
Table C-1: SmartOSD Menu Structure
........................................................................................76
DM Series Monitor
Page 1
Chapter
1
1 Introduction
DM Series Monitor
Page 2
1.1 Overview
Figure 1-1: DM Series
The DM series LCD monitor is the latest member of IEI’s line of sophisticated LCD designs, and it has been improved to be R oHS compliant. It is designe d to fit industrial automation, or an y other applications that r equir e m inim um ins tallation s pace and f lexible configuration. The f lat front panel provides I P 65 protection, which effectively wards off dust and water. Flexible anal og or digital interfaces are provided f or ease of connection with a management computer.
1.2 Features
The DM series have the following standard features:
IP 65 compliant aluminum front panel  Analog VGA interface supports most general system boards  Over 300 cd/m
2
high brightness LCD panel
Analog resistive type touch panel  Advanced thermal and air-flow design  Supports panel, rack, wall, DIN rail, stand and arm mounting  M models support 9~36V DC power input for mobile application  Long product life support  RoHS compliant
DM Series Monitor
Page 3
1.3 Model Variations
The DM series LCD monitor has the following three base models.
DM-150: 15” LCD screen  DM-170: 17” LCD screen  DM-190: 19” LCD screen
The DM series LCD monitor base models have a variety of variants. The model variations are listed in Table 1-1.
Model Number LCD
9~36V Power
Input
DM-150GS/R-R30
15”
­DM-150GMS/R-R30 Yes DM-170GS/R-R30
17”
­DM-170GMS/R-R30 Yes DM-190GS/R-R30
19”
­DM-190GMS/R-R30 Yes
Table 1-1: DM Series Model Variations
1.4 Applications
The DM series LCD monitor is designed for rigorous industrial environments where it may be exposed to both heat and m oisture. Its durability and str ength also makes it an idea l choice for public access computers. Some possible applications include:
Digital surveillance  X-ray imaging terminal  Multimedia advertising platform  General Computing
o Computer-based testing center o General purpose information system o Mobile nursing station o Interactive education use
Automation & Control
DM Series Monitor
Page 4
o Plant environment monitoring o Factory automation HMI terminal o Shop-floor/MES control
Self-service Kiosk
o Full-service receptionist kiosk o Hospital self-registrating terminal o Interactive photo kiosk o Video rental kiosk o Self-service POS terminal
1.5 Extern al Overview
The DM series LCD monitors are durable devices that can be used in harsh industrial environments. The f ollowing sections desc ribe the physical layout of the D M series LCD monitors.
1.5.1 Front View
The front of the DM series LCD monitor is a flat panel LCD screen surrounded by an aluminum fram e. A control butto n panel (OSD ), if available, is located either vertic ally on the right side of the f rame or hor izontall y along the bo ttom of the fram e with the follo wing control buttons:
LCD On/Off  Auto  Left  Right  Menu
The OSD panel also has one power LED.
Figure 1-2 shows a typical monitor front view.
DM Series Monitor
Page 5
Figure 1-2: Typical Monitor Front View
1.5.2 Bottom Panel View
Figure 1-3 shows the bottom panel of the DM series LCD monitor. All connectors are fully described in Section 5.4.
Figure 1-3: Bottom Panel View
DM Series Monitor
Page 6
1.5.3 AD Board
The DM series LCD monitor AD board provides a wide variety of control interfaces, receiving and m anaging signals from a CPU card through cabli ng. Figure 1-4 shows the AV-6600 AD bo ard as a sample of a typical AD board for the DM series LCD monitor. Refer to Chapter 4 for a complete description of AD boards and their connectors.
Figure 1-4: AV-6600 AD Board
DM Series Monitor
Page 7
1.6 Series Specifications
Table 1-2 shows the DM Series specifications.
Model DM-150GS DM-150GMS DM-170GS DM-170GMS DM-190GS DM-190GMS
LCD Size 15” 15” 17” 17” 19” 19”
Resolution 1024x768 1024x768 1024x768 1024x768 1024x768 1024x768
Brightness
(cd/m2)
400 400 350 350 350 350
Contrast
Ratio
700:1 700:1 800:1 800:1 1000:1 1000:1
LCD Color 16.2M 16.2M 16.7M 16.7M 16.7M 16.7M
Pixel Pitch
(mm)
0.297 0.297 0.264 0.264 0.264 0.264
Viewing
Angle (H/V)
160/140 160/140 170/160 170/160 170/160 170/160
Touch
Resistive 5-wire
USB/RS-232
interface
Resistive 5-wire
USB/RS-232
interface
Resistive 5-wire
USB/RS-232
interface
Resistive 5-wire
USB/RS-232
interface
Resistive 5-wire
USB/RS-232
interface
Resistive 5-wire
USB/RS-232
interface
AD Board AV-6600 Aluminum AV-6600 AV-6600 AV-6600 AV-6600
Input
Interface
Analog VGA
+ DVI-D
Analog VGA
+ DVI-D
Analog VGA
+ DVI-D
Analog VGA
+ DVI-D
Analog VGA
+ DVI-D
Analog VGA
+ DVI-D
OSD function
Yes Yes Yes Yes Yes Yes
Smart-OSD Yes Yes Yes Yes Yes Yes
Dimension
(WxHxD)
(mm)
410 x
309 x
64.4
410 x
309 x
64.4
452.0 x
356.0 x
65.2
452.0 x
356.0 x
65.2
482 x
399 x
73
482 x
399 x
73
Operating
Temperature
-10°C~50°C -10°C~50°C -10°C~50°C -10°C~50°C 0~50°C 0~50°C
Storage
Temperature
-20°C~60°C -20°C~60°C -20°C~60°C -20°C~60°C -10°C~60°C -10°C~60°C
Net Weight 6kg 6kg 8.6kg 8.6kg 10kg 10kg
Input
Voltage
12VDC 9-36VDC 12VDC 9-36VDC 12VDC 9-36VDC
DM Series Monitor
Page 8
Model DM-150GS DM-150GMS DM-170GS DM-170GMS DM-190GS DM-190GMS
Power
Adapter
60W N/A 60W N/A 60W N/A
Certificates
Internal
Prescan
EMC Class A
Internal
Prescan
EMC Class A
Internal
Prescan
EMC Class A
Internal
Prescan
EMC Class A
Internal
Prescan
EMC Class A
Internal
Prescan
EMC Class A
Table 1-2: DM Series Specifications
1.7 Certifications
All DM series LCD monitor models comply with the following international standards:
RoHS  IP 65
For a more detailed description of these standards, please refer to Appendix B.
DM Series Monitor
Page 9
Chapter
2
2 Mechanical Overview
DM Series Monitor
Page 10
2.1 Introduction
This chapter describes the general mechanical overview of the DM series monitors including front and bottom panel variations, available interfaces and overall dimensions.
2.2 Front Panel
The front panel of the DM series LCD monitor is comprised of a LCD in an alum inum frame with an OSD co ntr ol pane l.
2.2.1 Front Panel Variants
Table 2-1 shows the three front panel variants for the DM series LCD monitor.
Model OSD Control Panel Location
Va ria n t
Number
DM-150, DM-170
Vertically along the right side of the aluminum frame
1
DM-190
Horizontally along the bottom of the aluminum frame
2
Table 2-1: Front Panel Variants
2.2.2 Front Panel Variant 1
The following models of the DM series LCD monitor have an OSD control panel loc ated vertically along the right side of the aluminum frame:
DM-150  DM-170
Figure 2-1 shows the location of the front panel variant 1 OSD controls.
DM Series Monitor
Page 11
Figure 2-1: Front Panel Variant 1
2.2.3 Front Panel Variant 2
The following model of the DM series LCD monitor has an OSD control panel located horizontally along the bottom of the aluminum frame:
DM-190
Figure 2-2 shows the location of the front panel variant 2 OSD controls.
DM Series Monitor
Page 12
Figure 2-2: Front Panel Variant 2
2.2.4 Bottom Panel
All peripheral device conn ectors are located on the bottom panel of the DM series LCD monitor. The follo wing sections describe t he bottom panel variants and their associated connectors.
2.2.5 Available Connectors
There are a number of bottom panel peripheral device c onnectors available for the D M series LCD monitor.
VGA connector  DVI-D connector  12V power connector  9~36V terminal block (Optional for M model, refer to Table 1-1) RS-232 serial connector  USB connector
DM Series Monitor
Page 13
2.3 Phy sical Dimensions
The following sections des cribe the p hysical dim ensions f or each model of the DM series LCD monitor.
2.3.1 Gener al Phys ical Dimens ions
General physical dimensions for the DM series LCD monitors are shown in Table 2-2.
Model Width
(mm)
Height
(mm)
Depth
(mm)
DM-150 410 309 64.4 DM-170 452 356 65.2 DM-190 482 399 73
Table 2-2: General Physical Dimensions
DM Series Monitor
Page 14
2.3.2 DM-150 Phys ical Dimens ions
The physical dimensions of the DM-150 are shown in Figure 2-3.
Figure 2-3: DM-150 Physical Dimensions (millimeters)
DM Series Monitor
Page 15
2.3.3 DM-170 Phys ical Dimens ions
The physical dimensions of the DM-170 are shown in Figure 2-4.
Figure 2-4: DM-170 Physical Dimensions (millimeters)
DM Series Monitor
Page 16
2.3.4 DM-190 Phys ical Dimens ions
The physical dimensions of the DM-190 are shown in Figure 2-5.
Figure 2-5: DM-190 Physical Dimensions (millimeters)
DM Series Monitor
Page 17
2.3.5 Optional Mounting Kits
The following sections describe the various optional mounting kits available for each model of the DM series LCD monitor. Refer to Sectio n 5.5 for detailed instructions on t he different mounting methods for the monitors.
CAUTION:
Due to safety conc erns, it is highly r ecommended to use th e VESA mounting kits provided by IEI for w all, s tand and ar m moun ting. If the VESA m ountin g kit is purchased separately, please make sure the mounting kit is UL-listed.
2.3.6 DM-150 Mounting Kits
Table 2-3 lists the mounting kits available for the DM-150 monitor.
Model DM-150 Panel Mounting Kit PK-150M Rack Mounting Kit RK-150MS-R10
Wall Mounting Kit WK-150MS-R10 LCD Monitor Arm ARM-31 LCD Monitor Stand STAND-100-RS
Table 2-3: DM-150 Mounting Kits
2.3.7 DM-170 Mounting Kits
Table 2-4 lists the mounting kits available for the DM-170 monitor.
Model DM-170 Panel Mounting Kit PK-170M Rack Mounting Kit RK-170MS-R10 Wall Mounting Kit WK-170MS-R10
LCD Monitor Arm ARM-31
DM Series Monitor
Page 18
LCD Monitor Stand STAND-100-RS
Table 2-4: DM-170 Mounting Kits
2.3.8 DM-190 Mounting Kits
Table 2-5 lists the mounting kits available for the DM-190 monitor.
Model DM-190 Panel Mounting Kit PK-190M Rack Mounting Kit RK-190MS-R10
Wall Mounting Kit WK-190MS-R10 LCD Monitor Arm ARM-31
LCD Monitor Stand -
Table 2-5: DM-190 Mounting Kits
DM Series Monitor
Page 19
Chapter
3
3 LCD Specifications
DM Series Monitor
Page 20
3.1 LCD Specifications
3.1.1 LCD Overview
The DM series LCD monitors use the following LCD panels.
DM-150: AUO G150XG01 V3  DM-170: AUO G170EG01 V1  DM-190: AUO G190EG01 V1
Detailed specifications for the LCD screens are listed in the following sections.
3.1.2 DM-150 LCD Specifications
Table 3-1 lists the DM-150 LCD specifications.
Items DM-150
Size 15” Brand AUO Model G150XG01 V3 Backlight LED Brightness (cd/m2) 400 Resolution 1024 x 768 Screen Scale 4:3 Life Time 50000H Contrast Ratio 700:1 View Angle (H/V) 160/140 Interface 1ch LVD S Operating Temperature -30~85°C Active Area (mm) 304.1 x 228.1 Pixel Pitch (mm) 0.297 Display Mode Normal White Number of Colors 16.2M Supply Voltage (V) 3.3
Table 3-1: DM-150 LCD Specifications
DM Series Monitor
Page 21
3.1.3 DM-170 LCD Specifications
Table 3-2 lists the DM-170 LCD specifications.
Items DM-170
Size 17” Brand AUO Model G170EG01 V1 Backlight LED Brightness (cd/m2) 350 Resolution 1280 x 1024 Screen Scale 4:3 Life Time 50000H Contrast Ratio 800:1 View Angle (H/V) 170/160 Interface 2ch LVD S Operating Temperature -30~85°C Active Area (mm) 337.9 x 270.3 Pixel Pitch (mm) 0.264 Display Mode Normal White Number of Colors 16.7M Supply Voltage (V) 5
Table 3-2: DM-170 LCD Specifications
3.1.4 DM-190 LCD Specifications
Table 3-3 lists the DM-190 LCD specifications.
Items DM-190
Size 19” Brand AUO Model G190EG01 V1 Backlight LED
DM Series Monitor
Page 22
Brightness (cd/m2) 350 Resolution 1280 x 1024 Screen Scale 4:3 Life Time 50000H Contrast Ratio 1000:1 View Angle (H/V) 170/160 Interface 2ch LVDS Operating Temperature 0~50°C Active Area (mm) 376.32 x 301.06 Pixel Pitch (mm) 0.294 Display Mode Normal White Number of Colors 16.7M Supply Voltage (V) 5
Table 3-3: DM-190 LCD Specifications
DM Series Monitor
Page 23
Chapter
4
4 AD Board
DM Series Monitor
Page 24
4.1 AD Board Overview
The DM series LCD monitor AD board provides a wide variety of control interfaces, receiving and managing i nterf ace s ignals fr om a CPU card through c abling . The following sections describe each AD board in detai l.
4.2 AV-6600 AD B oard Overview
The AV-6600 AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-6600 AD board in detail.
Figure 4-1: AV-6600 AD Board Overview
4.2.1 AV-6600 Peripheral Interface Connectors
Table 4-1 shows a list of the peripheral interface connectors on the AV-6600 AD board.
DM Series Monitor
Page 25
Connector Type Label
Audio input connector 4-pin wafer connector CN11
Audio speaker output connector 4-pin wafer connector CN12
Auto-dimming connector 6-pin wafer connector CN7
Debug connector 4-pin wafer connector CN9
External OSD and LED indication connector 9-pin wafer connector CN10
Infrared connector 6-pin wafer connector CN8
Inverter interface connector 6-pin wafer connector CN6
LVDS connector 30-pin connector CN5
Power output connector (+12 V) 2-pin wafer connector CN3
Power output connector (+5 V) 2-pin wafer connector CN4
Power input connector 3-pin connector CN2
RS-232 and USB signal input connector 12-pin wafer connector CN14
Touchscreen connector 9-pin wafer connector J4
VGA connector 10-pin box header VGA2
Table 4-1: AV-6600 Peripheral Interface Connectors
4.2.2 AV-6600 Rear Panel Connectors
Table 4-2 lists the rear panel connectors on the AV-6600 AD board.
Connector Type Label
12V DC power connector DC Power Jack CN13
DVI connector 24-pin DVI-D connector J2
VGA connector 15-pin VGA connector VGA1
Table 4-2: AV-6600 Rear Panel Connectors
DM Series Monitor
Page 26
Chapter
5
5 Installation
DM Series Monitor
Page 27
5.1 Installation Pre cautions
When installing the DM series LCD monitor, please follow the precautions listed below:
Read the user manual: The user manual provides a complete description of
the DM series LCD monitor, installation instructions and configuration options.
DANGER! Disconnect Power: Power to the monitor must be disconnected
when installing the DM series LCD monitor, or before any attempt is made to access the rear panel. Electric shock and personal injury might occur if the rear panel of the monitor is opened while the power cord is still connected to an electrical outlet.
Qualified Personnel: The DM series LCD monitor must be installed and
operated only by trained and qualif ied pers onn el. Ma intenanc e , upgr ad es , or repairs may only be carried out by qualified personnel who are familiar with the associated dangers.
Mounting: Since the monitor may weigh up to 10 kg (not including a swing
arm or other accessories), please ensure at least two people assist with mounting the monitor.
Air Circulation: Make sure there is sufficient air circulation when installing the
monitor. The monitor’s cooling vents must not be obstructed by any objects. Blocking the vents can cause overheating of the monitor. Leave at least 5 cm of clearance around the monitor to prevent overheating.
Grounding: The monitor should be properly grounded. The voltage feeds
must not be overloaded. Adjust the cabling and provide external overcharge protection per the electrical values indicated on the label attached to the back of the monitor.
Anti-static Discharge: The rear panel of the monitor must to be removed to
configure the monitor’s AD board voltage select jumper. When doing so, be sure the monitor is disconnected from its power source and take all necessary safety precautions to avoid electrocution and static discharge to the AD board. The use of a grounded wrist strap and an anti-static work pad is recommended.
DM Series Monitor
Page 28
5.2 Unpacking
5.2.1 Packaging
When shipped, the D M series LCD monitor is wrapped in a plastic bag. Two pol ystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box.
5.2.2 Unpacking Procedure
To unpack the DM series LCD monitor, follow the steps below:
WARNING:
The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the DM series LCD monitor has been properly installed. This ensures the screen is protected during the installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the DM series LCD monitor.
Step 7: Make sure all the components listed in the packing list are present. Step 0:
DM Series Monitor
Page 29
5.2.3 Packing Lis t
All the monitors in the DM series are shipped with the following components:
1 x DM-150/170/190 series LCD monitor.  1 x AC power cable  1 x VGA cable  1 x 60W power adapter  5 x Replacement round head screw  5 x Replacement flat head screw  5 x Replacement wire strain band  1 x Touch panel RS-232 cable  1 x Touch panel USB cable
1 x Touch Pen  1 x Utility CD  1 x Power cable for terminal block (Optional for M model)
If any of these items are missing or damaged, contact the distributor or sales representative imm ediately.
5.3 Pre-installat ion Pr eparat ion
5.3.1 Tools
Before installing the DM series LCD monitor, make sure the following tools are on hand:
Philips (crosshead) screwdriver: All the retention screws on the system are
Philips screws.
Soft working mat: When the DM series LCD monitor is installed, the screen
is placed on the working surface. It is therefore important to rest the MPC industrial workstation on a soft at that cannot damage the LCD screen on the front of the DM series LCD monitor.
DM Series Monitor
Page 30
5.3.2 Voltage Select Jumper Settings
If the monitor com es with both 12V and 9~36V DC power connectors , the voltage sel ect jumper on the inte grated AD boar d must be configured f or the D C connect or that is used to power the monitor. Refer to Chapter 4 for the appropriate jum per settings of each AD board.
NOTE:
The default voltage select jumper is configured for a 12V power source.
Do not change the jumper setting unless a 9~36V DC power connector is present on the rear panel and is to be used as the monitor’s power source.
To properly set the voltage select jumper, the following steps must be completed:
Step 1: Use a screwdriver to remove all the screws holding the rear panel to the monitor .
Step 2: Remove the rear panel.
Step 3: Locate the voltage select jumper. (See Chapter 4)
Step 4: Use the jumper(s) to set the correct voltage input. (See Chapter 4)
Step 5: Replace the rear panel.
Step 6: Replace all removed screws.Step 0:
DM Series Monitor
Page 31
5.4 Connectors
Table 5-1 lists the rear panel connectors for the DM series LCD monitors.
Connectors DM-150 DM-170 DM-190
VGA Yes Yes Yes DVI-D Yes Yes Yes Powe r (12V Jack) Yes Yes Yes RS-232 for Touch Panel Yes Yes Yes USB for Touch Panel Yes Yes Yes
Powe r (9~36V Termin al Block) (Optional for M model)
Yes Yes Yes
Table 5-1: Rear Panel Connectors
5.4.1 Rear Panel Connectors Overview
Figure 5-1: Monitor Rear Panel Connection s
DM Series Monitor
Page 32
Figure 5-1 shows all the pos sible rear panel con nectors for the DM series LCD monitor. Refer to Table 5-1 for a list of the monitors and their corresponding connectors. The following sections fully describe the rear panel connectors for the DM series LCD monitor.
5.4.2 VGA Connector
Use the rear pane l standard 15-pin female VGA connector to connect the m onitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION 1 RED 6 GROUND 11 NC 2 GREEN 7 GROUND 12 DDCDAT 3 BLUE 8 GROUND 13 HSYNC 4 NC 9 NC 14 VSYNC 5 GROUND 10 GROUND 15 DDCCLK
Table 5-2: VGA Connector Pinouts
Figure 5-2: VGA Connector
5.4.3 DVI-D Connector
Use the rear panel standar d 24-pin female DVI-D connec tor to con nect the m onit or to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION 1 TMDS Data2- 9 TMDS Data1- 17 TMDS Data0­2 TMDS Data2+ 10 TMDS Data1+ 18 TMDSData0+ 3 TMDS Data2/4 Shield 11 TMDS Data1/3 Shield 19 TMDS Data0/5 Shield 4 TMDS Data4- 12 TMDS Data3- 20 TMDS Data5­5 TMDS Data4+ 13 TMDS Data3+ 21 TMDS Data5+ 6 DDC Clock [SCL] 14 +5 V Power 22 TMDS Clock Shield 7 DDC Data [SDA] 15 Ground (for +5 V) 23 TMDS Clo ck +
DM Series Monitor
Page 33
8 Analog vertical sync 16 Hot Plug Detect 24 TMDS Clock -
Table 5-3: DVI-D Connector Pinouts
Figure 5-3: DVI-D Connector
5.4.4 12V P ower Connector
Use the rear panel +12V DC jack to connect the monitor to a power source.
Figure 5-4: 12V Power Connector
5.4.5 RS-232 for Touch Panel Connector
Use the rear panel standard RS-232 DB-9 female touc h panel connector to connect the monitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION 1 N/A 6 NDSR 2 NRX 7 NRTS 3 NTX 8 N/A 4 NDTR 9 N/A 5 GND
Table 5-4: RS-232 Touch Panel Connector Pinouts
DM Series Monitor
Page 34
Figure 5-5: RS-232 Touch Panel Connector
5.4.6 USB for Touch Panel Connector
Use the rear panel standard USB touch pa nel connector to connect the monitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION 1 VCC 5 VCC 2 Data- 6 Data­3 Data+ 7 Data+ 4 GND 8 GND
Table 5-5: USB Touch Panel Connector Pinouts
Figure 5-6: USB Touch Panel Connector
5.4.7 Optional Terminal Block
Use the rear pane l 3-pin terminal block DC power connector to connect the monitor to a DC power source.
DM Series Monitor
Page 35
Figure 5-7: Terminal Block
5.5 Mounting the Monitor
The DM series LCD monitor can be mounted in a panel, cabinet, rack or wall. The monitor can also be mounted on a monitor arm or stand. T he mounting methods are described below.
CAUTION:
When mounting th e monitor take care t o tighten the retentio n screws or bolts until fully secure, but do no t over tighten. Over ti ghtening the retentio n screws or bolts may cause them to become stripped, rendering them useless.
5.5.1 Panel Mounting
Each model of the DM series LCD monitor has a series of mounting slots locate d on the top and bottom panel for mounting the monitor to a panel.
Table 5-5 lists the number of mounting clamps required to mount the monitor to a panel.
Model Mounting Clamps
DM-150 10 DM-170 10 DM-190 14
Table 5-6: Panel Mounting Clamps
DM Series Monitor
Page 36
To mount the DM series LCD monitor into a panel, please follow the steps below.
Step 1: Select the position on the panel to mount the monitor.
Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of
the monitor. Take care that the panel section that is cut out is smaller than the overall size of the metal frame that surrounds the monitor but just large enough for the rear panel of the monitor to fit through.
Figure 5-8: DM-150 Panel Opening (Unit: mm)
Figure 5-9: DM-170 Panel Opening (Unit: mm)
DM Series Monitor
Page 37
Figure 5-10: DM-190 Panel Opening (Unit: mm)
Step 3: Slide the monitor through the hole until the metal frame is flush against the panel
(Figure 5-11).
Figure 5-11: Insert the Monitor
DM Series Monitor
Page 38
Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of
the monitor, behind the metal frame. Refer to the mounting kit packing list for the required number of mounting clamps.
Figure 5-12: Panel Mounting Clamp Position
Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic
caps at the front of all the screws are firmly secured to the panel (Figure 5-12).
5.5.2 Cabinet and Rack Ins tallation
Each model of the DM series LCD monitor has a series of holes located on the rear of the front panel for mounting the monitor to a rack or cabinet.
NOTE:
1. The DM-190 monit or requires two spec ial mounting brackets for ins tallation into a rack or cabinet. Refer to Section 5.5.2.2 for details.
DM Series Monitor
Page 39
5.5.2.1 Standard Cabinet and Rack Ins tallation
The standard cabinet/r ack mounting procedure applies to the following DM series LCD monitors:
DM-170
DM-150
To mount the DM series LCD monitor into a cabinet/rack, please follow the steps below.
Step 1: The back of the metal frame surrounding the DM series LCD monitor has
several retention screw holes for a cabinet/rack installation bracket.
NOTE:
When purchasing a cabinet/rack
installation bracket, make sure it is
compatible with both the monitor and the cabinet/rack into which the monitor is installed.
Step 2: Slide the monitor through the cabinet/rack bracket until the rear side of the
monitor frame is flush against the front of the bracket.
Step 3: Make sure the retention screw holes at the rear of the monitor frame are aligned
with the retention screw holes in the cabinet/rack bracket.
Step 4: Secure the cabinet/rack bracket to the monitor by inserting and tightening the
retention screws (Figure 5-13).
DM Series Monitor
Page 40
Figure 5-13: Secure the Cabinet/Rack Bracket
Step 5: Slide the monitor with the attached cabinet/rack bracket into a rack or cabinet
(Figure 5-14).
Figure 5-14: Install into a Cabinet/Rack
DM Series Monitor
Page 41
Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into
the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-14).
5.5.2.2 DM-190 Cabinet and Rack Ins tallation
To mount the DM-190 monitor into a cabinet/rack, please follow the steps below.
Step 1: Insert and tighten the supplied mounting nuts and bolts to the rack for the rack
mounting bracket. Each bracket requires three nuts and bolts for installation. (See Figure 5-15)
Figure 5-15: Rack Mounting Nuts and Bolts Installation (DM-190)
Step 2: Secure the rack mounting bracket to two sides of the monitor using the supplied
retention screws. Each bracket requires four screws. (See Figure 5-16)
DM Series Monitor
Page 42
Figure 5-16: Rack Mounting Bracket Installation (DM-190)
Step 3: Carefully insert the slotted holes of the brackets on the monitor through the bolts
on the rack and gently pull the monitor downwards until the bolts rests securely in the slotted holes. (See Figure 5-17). Ensure that all six of the bolts fit snuggly into their respective slotted holes.
Figure 5-17: Rack Mounting (DM-190)
DM Series Monitor
Page 43
5.5.3 Wall Mounting
CAUTION:
Due to safety conc erns, it is highly r ecommended to use the V ESA mounting kits provided by IEI for w all, s tand and ar m moun ting. If the VESA m ountin g kit is purchased separately, please make sure the mounting kit is UL-listed.
Each model of the DM s eries LCD monitor has f our holes located on the rear panel for mounting the monit or to a w all. To mount the DM series LCD m onitor onto a wall, please follow the steps below.
Step 1: Select a location on the wall for the wall-m ounting bracket.
Step 2: Carefully mark the locations of the four bracket screw holes on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into
the four pilot holes and tightening them (Figure 5-18).
Figure 5-18: Wall-mounting Bracket
DM Series Monitor
Page 44
Step 6: Insert the four monitor mounting screws (M4 screws) provided in the wall
mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel (Figure 5-19).
Figure 5-19: Monitor Support Screws
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes (Figure 5-20). Ensure that all four of the mounting screws fit snuggly into their respective slotted holes.
DM Series Monitor
Page 45
NOTE:
In the diagram below the bracket is already installed on the wall.
Figure 5-20: Wall Mounting the Monitor
5.5.4 Monitor Stand Ins tallation
The DM series LCD monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-21).
DM Series Monitor
Page 46
Figure 5-21: VESA Mounting Holes
The monitor stand mounting plate has a matching VESA hole pattern. To mount the DM series LCD monitor onto a stand, please follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor stand mounting plate.
Step 2: Secure the monitor to the stand with the supplied retention screws (Figure
5-22).
Figure 5-22: Monitor Stand Mounting
DM Series Monitor
Page 47
5.5.5 Monitor Arm Ins tallation
The DM series LCD monitor has Video Electronics Standards Association (VESA) standard mounting holes t apped into the rear panel. The standard holes ar e M4 set at 100m x 100mm apart (Figure 5-21). The monitor arm mounting plate has a matching VESA hole pattern. To mount the DM series LCD monitor onto a monitor arm, please follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the
monitor arm mounting plate.
Step 2: Secure the monitor to the arm with the supplied retention screws (Figure 5-23).
Step 0:
Figure 5-23: Monitor Arm Mounting
DM Series Monitor
Page 48
Chapter
6
6 On-Screen-Display (OSD)
Controls
DM Series Monitor
Page 49
6.1 User Mode OSD Structure
6.1.1 OSD Buttons
There are several on-screen-display (OSD) control buttons oriented either vertica lly a lon g the right hand sid e or horizontally along the bottom of the monitor f ront panel. Refer to Section 2.2 for availability and orientation of the OSD controls on specific DM series monitors.
Figure 6-1 shows a typical arrangement of OSD controls of the DM series LCD monitor.
Figure 6-1: OSD Control Buttons
DM Series Monitor
Page 50
6.1.2 OSD Menu Structure
Table 6-1 shows the OSD menu structure for all models of the SRM series LCD monitor.
Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100
Contrast 0 to 100 Clock 0 to 100 Phase 0 to 100 H. Position 0 to 100 V. Position 0 to 100 Sharpness 1 to 5
Color Menu 6500K - Preset NTSC value
7500K - Preset NTSC value 9300K - Preset NTSC value Red RGB values from 0 to 100 Green RGB values from 0 to 100 Blue RGB values from 0 to 100
OSD Menu OSD Time Out 0 to 60 sec
OSD Position 1 to 5 OSD Transparency 20, 40, 60, 80, 10 0 Factory Reset Select Auto Adjust Select Auto Color Select Gamma Off, On
Exit Menu Exit Select
Table 6-1: OSD Menus
DM Series Monitor
Page 51
6.2 Using the OSD
OSD menu options are described below.
6.2.1 Main Dis play Features
Main display features are shown in Figure 6-2.
Figure 6-2: Main Display Features
Brightness
The brightness opt ion adjusts t
he brightness of screen. This function
adjusts the offset value of ADC. S
etting this valu e too high or to o low
will affect the quality of image. When the auto-
dimming function is
turned on, the brightness control is not effective.
Contrast
This function adjusts the g ain value of ADC. A
djusting this value too
high or too low will worsen the quality of image.
Clock
Adjusts the width of the display screen.
Phase
Adjusts the input signal.
H. Position
Adjusts the horizontal position of the display screen.
V. Position
Adjusts the vertical position of the display screen
Sharpness
Adjust the sharpness of the display
DM Series Monitor
Page 52
6.2.2 Color
Color options are shown in Figure 6-3.
Figure 6-3: Color Options
The Color menu fine-tunes the palette of color hues for the LCD.
6500k
NTSC standard Kelvin
7500k
NTSC standard Kelvin
9300k
NTSC standard Kelvin
User
This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic.
DM Series Monitor
Page 53
6.2.3 OSD Configurations
The OSD configurations are shown in Figure 6-4.
Figure 6-4: OSD Configurations Menu
OSD Configurations are described below.
OSD Time Out
Determines how many seconds the OSD screen stays on screen
before it disappears when OSD is left unattended.
OSD Position
Adjusts the OSD position on the screen. Position 1 is i
n the upper left
of the screen, position 2 in the upper right and position 3 in
the
center.
OSD Transparency
Adjust the transparency of the OSD menu background.
Factory Reset
Restores the default OSD settings. Note that this will restore all
default display settings.
Auto Adjust
Automatically adjusts the position of the display screen
Auto Color
Automatically adjusts the color settings.
DM Series Monitor
Page 54
Chapter
7
7 Software Drivers
DM Series Monitor
Page 55
7.1 Introduction
The touch panel contro ller enables ana log res istive t ouc h panels f or four -wire, fiv e-wir e & eight-wire models. The c ontroller directl y communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendl y operation. The touch pa nel driver emulates the left m ouse button and the right mouse bu tton functions.
The touch panel driver supports the following operating systems:
Microsoft
®
Windows® versions:
o Microsoft
®
Windows® 2000
o Microsoft
®
Windows® XP
o Microsoft
®
Windows® 2003
o Microsoft
®
Windows® 2008
o Microsoft
®
Windows® Vista
o Microsoft
®
Windows® 7
Microsoft
®
Windows® CE versions:
o Microsoft
®
Windows® CE 4.2
o Microsoft
®
Windows® CE 5.0
o Microsoft
®
Windows® CE 6.0
Linux Kernel 2.6
DOS
Driver installation is described below.
7.2 RS-232 or US B Touch Screen
Before installing the driver, connect the DM Series monitor to the m otherboard. The DM Series monitors support touch screen modality through an RS-232 or USB interface connection. Decide through which interface the touch screen is to be controlled.
RS-232 Interface: If the touch screen interface connection is an RS-232
connection, connect the RS-232 connector on the single board computer to the DB-9 connector of the DM Series monitor.
DM Series Monitor
Page 56
USB Interface: If the touch screen interface connection is a USB connection,
connect the USB connector on the single board computer to the external USB port connector of the DM Series monitor.
7.3 Touch Panel Driver Ins tallation
WARNING:
Before the touch screen driver is installed, make sure the system is connected to the m onitor with a USB cable or an RS-232 null cab le. Also, make sure the VG A connect or on th e system is connec ted to t he VGA connector on the bottom of the monitor.
To install the touch panel driver for the DM Series, please follow the instructions below:
Step 1: Connect the DM Series monitor to the single board computer. See above.
Step 2: Install the driver CD. Install the driver CD into the system to which the DM
Series monitor is connected.
Step 3: Select the Touch Screen option in the menu of driver CD. The directory in
Figure 7-1 appears.
Figure 7-1: Setup Icon
DM Series Monitor
Page 57
Step 4: Double click the setup icon in Figure 7-1.
Step 5: The Welcome screen in Figure 7-2 appears.
Figure 7-2: Welcome Screen
Step 6: Click Next to continue.
Step 7: The license agreement in Figure 7-3 appears. Accept the terms of the
agreement by clicking I Agree.
Figure 7-3: License Agreement
DM Series Monitor
Page 58
Step 8: The installation destination screen appears. See Figure 7-4. Click Install.
Figure 7-4: Initiate Install
Step 9: The installation of the program begins. See Figure 7-5.
Figure 7-5: Installation Starts
Step 10: When the installation is complete, the complete screen appears. See Figure 7-6.
To complete the installation process click Finish.
DM Series Monitor
Page 59
Figure 7-6: Finish Installation
7.4 Change the Touch Screen Interface
If the touch screen interface must be changed from an RS-232 interface to a USB interface or, from a USB interface to an RS-232 i nterface, the following steps m ust be followed.
Step 1: Uninstall the touch screen driver
Step 2: Remove the interface cable i.e. remove the RS-232 cable or the USB cable
Step 3: Install the new cable i.e. install the USB cable or the RS-232 cable.
Step 4: Reinstall the driver CD as described above. Step 0:
7.5 Calibrating the Touch Screen
To calibrate the touch sc reen cursor with th e motion of the touch scr een pen (or finger) , please follow the steps below:
Step 1: Make sure the sy stem is properly connected through an RS-232 or a USB
interface to the DM Seri es monitor.
Step 2: Make sure the touch screen driver is properly installed.
DM Series Monitor
Page 60
Step 3: Locate the PenMount Monitor icon in the bottom left corner of the screen.
Figure 7-7: PenMount Monitor Icon
Step 4: Click the icon. A pop up menu appears. See Figure 7-8.
Figure 7-8: PenMount Monitor Popup Menu
Step 5: Click Control Panel in the pop up menu shown in Figure 7-8.
Step 6: The configuration screen in Figure 7-9 appears.
Figure 7-9: Configuration Screen
DM Series Monitor
Page 61
Step 7: Double click the PenMount 6000 icon as shown in Figure 7-9.
Step 8: The calibration initiation screen in Figure 7-10 appears.
Step 9: Select the Standard Calibration button as shown in Figure 7-10.
Figure 7-10: Calibration Initiation Screen
Step 10: The calibration screen in is shown. See Figure 7-11.
Figure 7-11: Calibration Screen
Step 11: Follow the instructions. The user is asked touch the screen at five specified
points after which the screen is calibrated. Ste p 0:
DM Series Monitor
Page 62
Chapter
8
8 Gasket Replacement
DM Series Monitor
Page 63
8.1 Gasket Replacement
A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly.
NOTE:
If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket.
Step 1: Remove the old gasket from the sides of the monitor.
Step 2: Attach the new gasket to the monitor. Make sure the gasket fits precisely into the
groove along the edges of the monitor’s front panel (Figure 8-1).
Figure 8-1: Gasket Replacement
NOTE:
Compliance with the IP 65 standard depends on correct installation of the gasket. Be sure to check that the gasket is properly installed after changing it.
DM Series Monitor
Page 64
Appendix
A
A Safety Precautions
DM Series Monitor
Page 65
WARNING:
The precautions outlined in this chapter should be strictly followed. Failure to follow thes e pr ecaut ions may result in permanent d amage to the DM Series.
A.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
A.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
Follow the electrostatic precautions outlined below whenever the DM
Series is opened.
Make sure the power is turned off and the power cord is disconnected
whenever the DM Series is being installed, moved or modified.
Do not apply voltage levels that excee d th e sp ecified voltage range.
Doing so may cause fire and/or an electrical shock.
Electric shocks can occur if the DM Series chassis is opened when the DM
Series is running.
Do not drop or insert any objects into the ventilation openings of the DM
Series.
If considerable amounts of du st, wa ter, or fluids enter the DM Series, turn
off the power supply immediately, unplug the power cord, and contact the DM Series vendor.
DO NOT:
o Drop the DM Series against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature
DM Series Monitor
Page 66
A.1.2 Anti-s tatic Precautions
WARNING:
Failure to take ESD precautions during the installation of the DM Series may result in permanent damage to the DM Series and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the DM Series . Dry climates are especially susceptibl e to ESD. It is therefore critical that whenever the DM Series is opened a nd any of t he electrical components are handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging any electrical component.
Self-grounding: Before handling any electrical component, touch any
grounded conducting material. During the time the electrical component is handled, frequently touch any conducting materials that are connected to the ground.
Use an anti-static pad: When configuring or working with an electrical
component, place it on an antic-static pad. This reduces the possibility of ESD damage.
Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
A.2 Maintenance and Cleaning Precautions
When maintaining or cleaning the DM Series, please follow the guidelines below.
A.2.1 Maintenance and Cleaning
Prior to cleaning any part or component of the DM Series, please read the details below.
Except for the LCD panel, never spray or squirt liquids directly onto any other
components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened cloth.
DM Series Monitor
Page 67
The interior of the D M Seri es does not require cleaning. Keep fluids away
from the DM Series interior.
Be cautious of all small removable components when vacuuming the DM
Series.
Turn the DM Series off before cleaning the DM Series.
Never drop any objects or liquids through the openings of the DM Series.
Be cautious of any possible allergic reactions to solvents or chemicals used
when cleaning the DM Series.
Avoid eating, drinking and smoking within vicinity of the DM Series.
A.2.2 Cleaning Tools
Some components in the DM Series may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the DM Series.
Cloth – Although paper towels or tissues can be used, a soft, clean piece of
cloth is recommended when cleaning the DM Series.
Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol
can be used to clean the DM Series.
Using solvents – The use of solvents is not recommended when cleaning the
DM Series as they may damage the plastic parts.
Vacuum cleaner – Using a vacuum specifically designed for computers is one
of the best methods of cleaning the DM Series. Dust and dirt can restrict the airflow in the DM Series and cause its circuitry to corrode.
Cotton swabs - Cotto n s waps moistene d with rub bi ng alcoh ol or wat er are
excellent tools for wiping hard to reach areas.
Foam swabs - Whenever possible, it is best to use lint free swabs such as
foam swabs for cleaning.
DM Series Monitor
Page 68
Appendix
B
B Certifications
DM Series Monitor
Page 69
B.1 RoHS Compliant
All models in the DM LCD monitor series comply with the Restriction of Hazardous Materials (RoHS) Directi ve. This means that all component s used to build the industrial workstations and the workstation itself are RoHS compliant.
The RoHS Directive bans the placing on the EU market of new el ectrical and electronic equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants.
B.2 IP 65 Compliant Front Panel
The front panels on all five models in the DM series LCD monitors have an ingress protection rating (IP) of 65, IP65. The front panels are protec ted from dust particles and water spray.
DM Series Monitor
Page 70
Appendix
C
C smartOSD
DM Series Monitor
Page 71
C.1 IEI s martOSD Quick Ins tallation Guide
IEI smartOSD is a proprietary On-Screen-Displ ay (OSD) software solution f rom IEI that enables easy, remote monitor setting adjustments in a Windows environment. IEI smartOSD delivers excellent performance and provides more flexibility than the typical OSD hardware solutions when adjusting a monitor. smartOSD also allows monitor settings such as brightness, contrast, screen position, size, color gain to be read and changed over normal video cable (VGA or DVI). The smartOSD function is only supported by revision 1.1 models and above.
C.2 Pre-installat ion Notice
Before installing smartOSD software, please make sure one of the following operating systems is instal led:
Windows 95
Windows NT 4.0
Windows 98
Windows 2000
Windows 2003
Windows XP
Windows Vista
C.3 smartOSD Ins tall
Connect the DM Series to a host computer. Inser t the CD that cam e with the s ystem and follow the instructions below.
Step 1: When the CD is installed, the screen shown in Figure 8-2 appears.
DM Series Monitor
Page 72
Figure 8-2: smartOSD Installer
Step 2: Click “Smart OSD” in Figure 8-2.
Step 3: The welcome screen shown in Figure 8-3 appears.
Figure 8-3: smartOSD Welcome Screen
Step 4: Click Next to continue.
Step 5: The Folder Select screen in Figure 8-4 appears.
DM Series Monitor
Page 73
Figure 8-4: smartOSD Folder Select Screen
Step 6: Select the installation folder in Figure 8-4 shown above.
Step 7: Click Next to continue.
Step 8: The screen in Figure 8-5 appears.
Figure 8-5: smartOSD Confirm Installation
Step 9: Confirm the installation by clicking Next in the screen above.
Step 10: The program starts to install and the progress bar shown in Figure 8-6 appears.
DM Series Monitor
Page 74
Figure 8-6: smartOSD Installation Progress
Step 11: When the installation is complete the “Complete Installation” screen in Figure
8-7 appears.
Figure 8-7: smartOSD Installation Compl ete
Step 12: Click Close in the screen above.
Step 13: After quick setup is complete, the IEI smartOSD wizard logo appears on the
desktop as shown in the screen below.
Step 14: To access the smartOSD, click the smartOSD wizard logo.S tep 0:
DM Series Monitor
Page 75
C.4 Software Illustration
The table below shows the smartOSD menu structure for all IEI LCD monitors.
NOTE:
To update the display setting status immediately, push the refresh button on every page
To turn the system on, press ALT + P.
Item Elements
Management
Save/Load File Power Management
EDID
EDID contains basic information about the monitor and its capabilities.
Image
Brightness Contrast Sharpness
DM Series Monitor
Page 76
Display
Auto Adjust Phase Clock
Color
Auto Color User Red Gain User Green Gain User Blue Gain Color T emperature (5000k and 4200k disabled in the DM Series) Gamma
PIP
PIP (disabled in the DM Series) PIP Source Input (disabled in the DM Series) PIP Size (disabled in the DM Series)
System
Monitor Power Control Auto Brightness (disabled in the DM Series) Main Source Input (S-Video and CVBS disabled) Volume (disabled in the DM Series) Factory Presets/OSD Lock/OSD Unlock Mute (disabled in the DM Series)
Table C-1: SmartOSD Menu Structure
DM Series Monitor
Page 77
C.4.1 Manage Page
Figure 8-8: Manage Page
DM Series Monitor
Page 78
C.4.2 EDID Page
DM Series Monitor
Page 79
C.4.3 Imag e Page
DM Series Monitor
Page 80
C.4.4 Display Page (for analog signal)
DM Series Monitor
Page 81
C.4.5 Color Page
DM Series Monitor
Page 82
C.4.6 PIP Page
NOTE:
The functions in the PIP page are only available in the MDM Series and
AFOLUX Series monitors.
DM Series Monitor
Page 83
C.4.7 Sys tem Page
NOTE:
Some of the functions in th e System
Page are only available to som e of the
IEI LCD series as following:
Auto Brightness: SRM, MDM and AFOLUX series only  Main Source Input: MDM and AFOLUX series only  Volume: AFOLUX series only Mute: AFOLUX series only
DM Series Monitor
Page 84
C.4.8 About Page
DM Series Monitor
Page 85
C.5 smartOSD FAQ
For troubleshooting, please see the steps below:
C.5.1 Windows 2000 Ins tallation Failure
Installation fails under Windows 2000 and shows the following image:
Figure C-9: DLL Missing
Solution: Download and install service pack Windows Installer 3.1
C.5.2 Vista Installation Failure
Installation fail under Vista while showing following image:
Figure C-10: Windows Vista Error
DM Series Monitor
Page 86
Solution: Install SmartOSD.exe as the administrator authority
Figure C-11: Install as Ad ministrator
C.5.3 Model Failur e
The Model Fail error message shown below appears.
Figure C-12: Firmware Incompatibility
Solution: SmartOSD only supports firmware version 2.0 and following versions.
DM Series Monitor
Page 87
C.5.4 DDC Por t F ailur e
The DDC port fail error message shown below appears.
Figure C-13: DCC Port Failure
Solutions:
Check VGA or DVI cable
Check an IEI monitor is being used
Make sure the version is version 2.3 for the AFOLUX/MDM series and version
1.5 for the DM/ISDM/TDM/SRM/LCD-KIT series that have the SmartOSD functions
Check if the OSD control status is busy. A busy signal may cause the signal
message for a short time.
Loading...