IEI Integration IDDV-6304140A User Manual

IDDV-6304140A
140W DC/DC
ATX Converter Module
Version: 1.0
Quick Installation Guide
ABOUT THE IDDV-6304140A
The highly efficient, high-performance 140-watt IDDV-6304140A DC-to-DC vehicle ATX converter module provides 5V, 3.3V, 12V,
-12V and 5VSB outputs. The IDDV-6304140A is designed for vehicle PC and receives a wide range of inputs between 6 and 30 VDC. The IDDV-6304140A is built on an intelligent design and provides outstanding line and load regulations. The IDDV-6304140A is capable of sustaining 90% power efficiency.
The power module also solves the 5V standby problem by cutting off the 5VSB rail after an amount of time (defined by jumper settings) to prevent the battery from draining. When the battery voltage is below
10.7V for more than thirty seconds, the IDDV-6304140A shuts down. The IDDV-6304140A reactivates again only when the input voltage is higher than 10.7V.
SPECIFICATIONS
Highly compact design Smart system on/off control High efficiency up to 90% Load down protection Over voltage protection Over current protection Short circuit protection Battery voltage monitor Amplifier on-delay control RoHS compliant IrDA remote control Off (optional) Electrical Specifications:
o Total output capacity: 140W
5V@10A Max. 3.3V@10A Max.
12V@4A Max.
-12V@0.15A Max. 5VSB@1.5A Max.
o Input Voltage: 6VDC to 30VDC
Min. input operating voltage: 5.7V Max. input operating voltage: 30V
o Min. Power Up Voltage: 8V o Deep discharged shut down voltage: 10.6V
Dimensions: 45mm x 160mm Environment:
o Operating temperature: -20°C ~ +85°C o Storage temperature: -40°C ~ +125°C
Weight: NW: 118g Power Capacity:
Voltage
5V output 10A 50mV 1.5%
3.3V output 10A 50mV 1.5% 12V output 4A 50mV 1.5%
-12V output 0.15A 150mV 1.5% 5VSB output 1.5A 150mV 1.5%
Table 1: Maximum Power Capacity
Current (Max.)
Ripple (Vp-p)
Line Regulation
PACKING LIST
When you unpack the power module, make sure the following items have been shipped.
1 x IDDV-6304140A ATX converter module 1 x QIG (Quick Installation Guide) 1 x 20-pin ATX to 20-pin ATX/SATA/HDD cable
(optional)
1 x Wire to battery and ACC on (optional)
IDDV-6304140A QIG IEI Technology Corp. Page 1
IDDV-6304140A SYSTEM BLOCK DIAGRAM
The system block diagram of the IDDV-6304140A are shown below.
Figure 1: IDDV-6304140A System Block Diagram
IDDV-6304140A QIG IEI Technology Corp. Page 2
IDDV-6304140A DIMENSION DRAWING
The dimensions of the IDDV-6304140A are shown below.
Figure 2: IDDV-6304140A Dimension Drawing (measurement units: milli meter)
IDDV-6304140A CONNECTOR AND JUMPER LOCATIONS
The following diagram shows the connector and jumper locations of the IDDV-6 304140A.
Figure 3: IDDV-6304140A Connector and Jumper Locations
IDDV-6304140A QIG IEI Technology Corp. Page 3

AMPLIFIER ON DELAY FUNCTION (CN19)

PIN NO. DESCRIPTION
3 AMP 4 GROUND
Table 2: Amplifier On Delay Function Connector Pinouts
ATX POWER CONNECTOR (J1)
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 3.3V 11 3.3V 2 3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON 5 GND 15 GND 6 +5V 16 GND 7 GND 17 GND 8 Power good 18 -5V 9 5VSB 19 +5V 10 +12V 20 +5V
Table 3: ATX Power Connector Pinouts
BATTERY LOW LED CONNECTOR (CN19)
PIN NO. DESCRIPTION
1 LEDA 2 LEDB
Table 4: Battery Low LED Connector Pinouts

INFRARED INTERFACE CONNECTOR (OPTIONAL) (CN22)

PIN NO. DESCRIPTION
1 GROUND 2 Vcc (P5V) 3 IRRX
Table 7: Infrared Interface Connector Pinouts

POWER ON/OFF SWITCH CONNECTOR (EXTERNAL) (CN20)

PIN NO. DESCRIPTION
1 PWRSW 2 GROUND
Table 8: Power On/Off Switch (External) Connector Pinouts

POWER ON/OFF SWITCH CONNECTOR (MOTHERBOARD) (CN21)

PIN NO. DESCRIPTION
1 MB_SW 2 MB_SW1
Table 9: Power On/Off Switch (Motherboard) Connector Pinouts
BURNER PROGRAM FOR MICROCHIP (CN5)
PIN NO. DESCRIPTION
1 MODEDD/MCLR 2 Vcc 3 GROUND 4 LED/RB7 5 AMPLIFTER/RB6 6 NC
Table 5: Burner Program for Microchip Connector Pinouts
INPUT POWER CONNECTORS (CN15, CN16, CN17)
Connector DESCRIPTION
CN15 Battery(+) CN16 ACC On (signal) (Ignition) CN17 Battery(-) (GND)
Table 6: Input Power Connector Pinouts
IDDV-6304140A QIG IEI Technology Corp. Page 4

OPERATION MODE SELECT JUMPER (CN18)

Jumper Soft Off Delay Hard Off Delay Case 1
Case 2
Case 3
Case 4
Case 5
Case 6
Table 10: Operation Modes
After 10 seconds, shut down motherboard.
After 15 seconds, shut down motherboard.
After 15 seconds, shut down motherboard.
After 15 seconds, shut down motherboard.
After 40 seconds, shut down motherboard.
After 30 minutes, shut down motherboard.
After 10 seconds, shut down motherboard and cut off 5VSB rail.
After 45 seconds, cut off 5VSB rail.
After 1 hour, cut off 5VSB rail.
Never deactivate 5VSB. (Still monitor batter status)
After 1 hour, cut off 5VSB rail.
Never deactivate 5VSB. (Still monitor batter status)
FUNCTION Pin 1-2 Pin 3-4 Pin 5-6 Pin 7-8 Pin 9-10
Case 1 Case 2 Case 3 Case 4 Case 5 Case 6 Auto_On Manual_On
Table 0-11: Operation Mode Select Jumper Pinouts
short open open open open short open open short short open open open open short open short open short open open short short open
short open
IDDV-6304140A QIG IEI Technology Corp. Page 5
Loading...