IDT Technology RM382PA 01 User Manual
EN
1
TimeSphere
Wireless Projection Clock
Model No: RM382P / RM382PA
USER MANUAL
CONTENTS
Introduction .............................................................. 2
Overview ................................................................... 2
Front View ............................................................. 2
Base View ............................................................. 3
LCD Display .......................................................... 3
Getting Started ........................................................ 3
Power .................................................................... 3
Clock Display Modes ............................................ 4
Clock Reception ...................................................... 4
Reception Signal .................................................. 5
Clock Settings ......................................................... 5
Alarm ......................................................................... 5
Projector .................................................................. 6
Temperature ............................................................. 7
Reset ......................................................................... 7
Precautions .............................................................. 7
Specifications ......................................................... 8
About Oregon Scientific ........................................ 9
EU-Declaration of Conformity ...........................9
FCC Statement ........................................................ 9
Declaration of Conformity ................................... 10
RM382P_M_EN_OP_REVISED1.indd 1 4/19/06 5:51:28 PM
EN
2
1
2
3
4
5
6
7
8
INTRODUCTION
Thank you for selecting the Oregon Scientific™
projection clock (RM382P / RM382PA).
NOTE Please keep this manual handy as you use
your new product. It contains practical step-by-step
instructions, as well as technical specifications and
warnings you should know about.
OVERVIEW
FRONT VIEW
1. Projection ball: Projects time on the wall or ceiling.
(Twist the closed projection unit to adjust the
focus.)
2. Charging pad
3. SNOOZE / PROJECTION: Activates 8-minute
snooze; turns the continuous projection function ON
/ OFF
4. AL ON / OFF: Activates / deactivates the alarm(s)
5.
: Increases setting; enables clock radio
reception signal
6. MODE: Toggles between different clock displays;
enters clock setting mode
7. ALARM: Toggles between alarm 1, alarm 2 and
calendar mode; enters alarm setting mode
8. : Decreases setting; disables clock radio
reception signal
RM382P_M_EN_OP_REVISED1.indd 2 4/19/06 5:51:33 PM
EN
3
1
2
3
4
5
6
7
BASE VIEW
1. Charging base circles: Position the unit to project
the time vertically at 3 different angles
2. Indoor temperature sensor
3. Ventilation holes
4. Adapter slot
5. °C / °F: Selects temperature unit
6. EU / UK switch (RM382P only): Slide to select your
nearest radio signal base
7. RESET: Press to reset
8. Rechargeable battery compartment
9. RESET: Press to reset
10. : Press to turn projector ON / OFF
11. Light sensor: Control the brightness of backlight
LCD DISPLAY
1. Time
2. Clock radio reception signal
3. Rechargeable battery icon
4. Indoor temperature reading
5. Time zone / day of the week
6. Alarm 1 / 2 is activated
7. Alarm time / calendar
GETTING STARTED
POWER
MAIN UNIT
Plug in the AC adapter.
1
8
9
10
11
2
3
4
5
6
7
RM382P_M_EN_OP_REVISED1.indd 3 4/19/06 5:51:44 PM
EN
4
PROJECTION UNIT
Insert rechargeable batteries (2 x AAA 1.5V) before first
use, matching the polarity (+ and -):
1. Twist the ball counter-clockwise until it loosens.
2. Pull the top half upwards.
3. Lift up the battery compartment cover.
4. Slide the battery in.
5. Insert the plastic plug into the slot.
6. Press to turn the projector ON.
NOTE Make sure it is fully charged before first use.
NOTE When opening or closing the ball you will hear a
click signifying that it has opened or closed. Do not
keep
1
2
3
4
5
6
twisting beyond the click noise or you may break the unit.
NOTE appears with the projected time when the
projection unit batteries are low.
To charge the projection unit, place it on the main unit,
making sure that 1 of its 3 base circles is in contact with
the main unit, charging pad.
Charge the projection unit for 12 hours the first time and
8 hours from then on. This will provide the projection
unit with 10 hours continuous projection time.
is animated during charging and static when full.
CLOCK DISPLAY MODES
Press MODE to toggle between the clock displays:
•
Clock with seconds
•
Clock with weekday
•
Clock with time zone offset and weekday
NOTE The light sensor at the back of the clock will
detect the light level in the room and adjust the clock
display accordingly. Do not position the back of the
clock close to a wall or other object, otherwise the light
may not function.
CLOCK RECEPTION
This product is designed to synchronize its calendar
clock automatically once it is brought within range of
a radio signal:
RM382P_M_EN_OP_REVISED1.indd 4 4/19/06 5:51:58 PM
Loading...