IDTECK Star Finger007, Star Finger007SR User Manual

Download

STAR

FINGER007

1 DOOR ACCESS CONTROLLER WITH FINGERPRINT

USER’S MANUAL

Access Controller

Rev. V1.0

20030516 User’s Manual

STAR

FINGER007

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS Page 4

2. INTRODUCTION Page 6

2.1 IDENTIFYING SUPPLIED PARTS

2.2 ABOUT STAR FINGER007

2.3 SPECIFICATION

3. PRODUCT OVERVIEW Page 8

3.1 FUNCTIONS

3.2 PRODUCT EXPLANATION

3.2.1 Panel Description

3.2.2 Color Coded & Wiring Table

4. INSTALLATION REQUIREMENTS Page 12

4.1 WIRE/CABLE

5. INSTALLATION Page 13

5.1 TEMPLATE (Wall Mount)

5.2 BACKUP BATTERY S/W

5.4 SYSTEM INITIALIZATION (Extra Reader Port)

5.4 WIRING

5.4.1 POWER

5.4.2 INPUT CONNECTIONS

5.4.3 OUTPUT CONNECTIONS

5.4.4 READER CONNECTIONS (Extra Reader)

6. COMMUNICATIONS Page 17

6.1 RS232 COMMUNICATION PORT CONNECTION

6.2 RS-422 COMMUNICATION PORT CONNECTION

6.2.1 RS-422 COMMUNICATION (STANDALONE)

6.2.2 RS-422 COMMNUNICATION (MULTIPLE FINGER007 CONNECTIONS)

6.3 DIAL UP MODEM

6.4 TCP/IP CONVERTER (EXTERNAL VERSION)

7. BASIC SETTINGS Page 20

7.1 INITIALIZATION OF FINGER007

7.2 HOW TO ENTER THE SETUP MENU

7.3 DATE AND TIME SETTING

7.4 ID REGISTRATION

20030516 User’s Manual

8. OPERATION Page 25

8.1 NORMAL OPERATION

8.2 DEFAULT SETTING

STAR

FINGER007

9. SETTING CHANGES Page 26

9.1 SETUP MENU F1

9.2 SETUP MENU F2

9.3 SETUP MENU F3

9.4 SETUP MENU F4

APPENDIX Page 50

A. THE RELATION BETWEEN INPUT AND OUTPUT (DEFAULT) B. TROUBLE SHOOTING

WARRANTY AND SERVICE Page 56

TEMPLATE Page 57

20030516 User’s Manual

STAR

FINGER007

1. IMPORTANT SAFETY INSTRUCTIONS

To prevent injuries to persons and damages to property, please read all the instructions and follow them whenever you deal with this product.

After reading, please put this instruction manual where it can be easily seen for the system operator.

ON INSTALLATION AND POWER

Use 12V DC power ONLY.

- Connecting to higher than 12V DC may result in a risk of electric shock, fire, or heavy damage of the unit.

Do NOT install this product at places with wet or metallic dust, or that can be watered.

- There may be risks of electric shock and fire.

Do NOT install this product near electric motors running.

- The unit may not operate normally.

Do NOT set this product near heaters or any thing that produces heat.

- There may be a risk of fire.

Be ALWAYS careful not to short-circuit any part of the circuitry with tools like a screwdriver in hand.

- There may be a risk of fire or heavy damage of the unit.

ON MAINTENANCE

Do NOT use any kind of liquid for cleaning.

- There may be a risk of electric shock, fire or heavy damage of the unit. Use an air spray, if needed. Users are cautioned NOT to attempt repair of this product or modify the wirings set by the installer at their own discretion.

- It may pose the risk of fire, hardware damages, or abnormal operations of the unit. It is recommended not to use a flammable spray or something easy to burn near this product.

- There may be the risk of an explosion or fire. Keep the unit away from any unauthorized people.

- It may cause abnormal operations of the unit.

20030516 User’s Manual

STAR

FINGER007

NOTICE

Please, contact a designated service center or the outlet at which the product was purchased when

A. Any liquid has been spilt or sprayed onto the product. In this case, cut the power off first.

B. The product seems to be operating abnormally. C. The unit exhibits a distinct change in performance. D. The unit has fallen to be broken down or damaged on its case.

* The cost of repairing can be charged for troubles due to the improper handling or negligence of users or the operator.

20030516 User’s Manual

STAR

FINGER007

2. INTRODUCTION

2.1 IDENTIFYING SUPPLIED PARTS

Please unpack and check the contents of the box. (Optional accessories, if purchased, may be included in the package)

2.2 ABOUT STAR FINGER007

The STAR FINGER007 is a highly advanced, intelligent single door controller with a powerful 32bit and dual 8bit microprocessor to meet the market requirement for a robust integrated solution for access control and time & attendance. The unit is designed to be flexible and reliable as well as provide the ultimate in biometric high security at a reasonable cost. This user-friendly device allows you to register up to 720 fingerprint IDs (optional 2,000/4,500); add / delete user IDs conveniently; store up to 26,000 transactions in its event buffer; easily report and archive information to Excel or Access databases; and ultimately successfully manage all access control and time & attendance issues. With a built-in 4" RF reader, keypad for Personal Identification Numbers (PIN), and a sophisticated biometric fingerprint analyzer, the FINGER007 offers up to three levels of ID verification. Any combination of prox, PIN, and biometric may be used and different verification levels can be custom programmed for each user or user group. Four independent input ports can be utilized for a wide variety of controls including exit buttons, door contacts, PIR sensors and fire detection equipment. Actions to be taken and time settings can be programmed with the front keypad or via the intuitive Windows based software program. The FINGER007 can be used both as a stand-alone system and also be networked. All control setting values such as ID numbers, inputs/outputs, real-time clock, time schedules, and event transaction reports can be uploaded and/or downloaded to and from the host computer. The compact and contemporary unit is easily installed and programming requires no significant knowledge of access control or time & attendance. The Three-LED indicator lights inform you of the systems operating status at real time and the digital display acts as a programming aid as well as a regulation time clock. By bundling the ultimate in high security access control and comprehensive employee management tools into a compact user friendly unit, the field proven STAR FINGER007 has made real what until recently was thought only to be possible in science fiction.

20030516 User’s Manual

STAR

FINGER007

2.3 SPECIFICATION

CPU 32bit, dual 8bit Microprocessor

Memory

Program Memory : 64KB EEPROM

Data Memory : 512KB SRAM(battery backup) Power DC 12V/ 350mA max.(excluding lock current) Card Holders/ Event Buffer

Card Holders : 720(optional 2,000/4,500)

Event Buffer : 26,000 Reader Port 1 Extra port, 1 Internal port

Standard 26bit Wiegand(STAR FINGER007) Reader Data Format

Standard 34bit Wiegand(STAR FINGER007SR)

8 bit burst Format for keypad reader

RS232/RS422(up to 32 channels) selectable 4800, Communication port

9600(Default), 19200, 38400bps communication speed

4 Input ports/ DC12V/ 20mA

Input/Output

Keypad LCD Light source

2 Relay Output ports/ DC12V/ FORM-C Relay 2A max.

2 TTL Output ports: DC5V/ 20mA

16 Keypad (Back lighting)

1 x LCD module, 2Lines x 16ch, 65.6 x 13.8mm view area

LED (finger unit) Mounting Color Material

Wall mounted

Dark pearl gray

Polycarbonate Self diagnostic Yes Reset Power on Reset and Watchdog timer reset Operation Status 3 LED (red, green, yellow) in dicators Operation Environment

0°C ~ +40°C, 10% ~ 90%(Humidity)

Weight 525g Dimensions 161.6mm x 122.6mm x 36.5mm Certification FCC Class A part 15, UL294, MIC

20030516 User’s Manual

STAR

FINGER007

3. PRODUCT OVERVIEW

3.1 FUNCTIONS

Stand-Alone Operation

The STAR FINGER007(STAR FINGER007SR) is capable of having two readers(entry and exit). The unit receives card data signals from the RF readers and determines whether or not to unlock the door. When an input signal is sent, for example from and activated sensor or if the exit button pressed, the controller generates and logs an appropriate response. All events are kept in its own memory and sent to the host computer. The access controller is a true standalone device that in the event of a malfunction, will not affect other units, even if used in conjunction with one another.

Operation with Host Computer

All event transactions can be managed via the host computer. The data transmitted from the controller can be displayed and stored on the host PC.

Data Backup

The controller retains all user information and event data for 30 days, even in the event of power failure. CAUTION : Battery S/W must be set correctly before the unit running. (See the INSTALLATION section)

Keypad

If the STAR FINGER007 is not connected to host PC, the integrated keypad and LCD display module can also be used for the entire programming process manually.

Anti-Pass-Back

Using an additional proximity reader foe exiting, the Anti-Pass-Back mode can be set. Anti-Pass-Back mode prevents any entry or exit when the registered user did not properly followed one entry and one exit by the Anti-Pass-Back rule. APB only allowed exit for the user once got into the door first and it doesn’t allow any user trying twice entry or twice exit

Input/Output

The STAR FINGER007 has built-in 4 inputs and 4 outputs (2 relay outputs and 2 TTL outputs) which can

be used to manipulate a wide variety of controls.

20030516 User’s Manual

Time Schedule Setup

You can program 10 time schedules and apply one time schedule to each user. Each time schedule has 8 different time zones from Monday to Sunday(7 time zones) and one holiday. Each time zone has 5 different time codes so you can program 5 different time codes to each day. Also you can program time schedule for individual inputs and outputs. Note that the time schedule for input is activated time code for input device so that the input is activated during the time code on this time schedule. Each time schedule is linked to one of holiday schedule and this linked holiday only validates to holiday time code

STAR

FINGER007

of the time schedule.

Holiday Schedule Setup

Excepting Sunday, you can program 32 holidays to one holiday schedule. Each holiday schedule is linked to one time schedule which has time code for holidays. So you can program all holidays to holiday schedule and the time code for holidays is programmed to holiday time zone of time schedule. Example : A : Holiday schedule 01 linked to time schedule 01,

Holiday schedule 02 linked to time schedule 02.

B : Holiday schedule 02 linked to time schedule 01, Holiday schedule 01 linked to time schedule 02.

Forced Door Open and Door Open Alarm

When door is opened by force, Door Contact Output is generated. And, when the door is being opened by normal operation, after 20 sec. door-open alarm(blink buzzer) will be generated until the door is closed.

Duress Alarm

You can select Duress Mode enable or disable. If you select Duress Mode enable, in case of Duress, enter the 2 digit Duress Password and press <ENT> and open the door using general process. If you registered ID, then Duress Output will be generated, and alarm event will be sent to the host PC.

1:N Certification (IDENTIFICATION)

You can certify using the fingerprint alone without RF card or PIN. You can set this function through the <TYPE SELECTION> in SETUP MENU F1. In the IDENTIFICATION MODE, the security level gets higher automatically, FRR(False Rejection Ratio) as well, but FAR(False Accept Ratio) gets lower, which may result in a lower recognition ratio. When using this mode, you have to press the <ENT> key first, then the fingerprint scanner waits for a fingerprint to be scanned. When a fingerprint-scanning is completed, FINGER007 compares the data and makes corresponding outputs.

* CAUTION : The number of registrants must be 50 or less.

20030516 User’s Manual

STAR

FINGER007

Input window

3.2 Product Explanation

3.2.1 Panel Description

3 LED (showing

system status)

• FINGER007(of V4.70 or higher) has a S/W(reverse side – Template hole) for the backup battery

connection. Before the FINGER007 installation, it needs to be connected before H/W initialize so that backup battery can retain the memory during power failure.

LCD

16 Numeric keypad

Fingerprint

Function Key

OFF state ON state

BAT connection S/W

20030516 User’s Manual

STAR

FINGER007

3.2.2 Color Coded & Wiring Table

IO PORT NAME SIGNAL NAME COLOR CODED

POWER

Main Power(+12V) +12V RED Power Ground GND BLACK

OUTPUT

Door Relay(COM) COM(1) Gray with Red stripe Door Relay(NC) NC(1) Blue with White stripe

Door Relay(NO) Alarm Relay(COM) Alarm Relay(NC) Alarm Relay(NO) TTL Output1 TTL Output2

INPUT

Exit Button EXIT Orange Door Sensor CONTACT Yellow with Red stripe Aux Input 1 IN1 Green Aux Input 2 IN2 Green with White stripe

EXTRA READER

Wiegand Data0 DATA0 Pink Wiegand Data1 DATA1 Cyan

RS232 INTERFACE

RS232-TX TXD Black with White stripe

NO(1) White with Red stripe

COM(2) White

NC(2) Purple with White stripe

NO(2) Purple

TTL1 Orange with White stripe

TTL2 Brown with White stripe

20030516 User’s Manual

RS232-RX RXD Red with White stripe

RS422 INTERFACE

RS422-TX(-) TX(-) Yellow RS422-TX(+) TX(+) Gray RS422-RX(-) RX(-) Blue RS422-RX(+) RX(+) Brown

STAR

FINGER007

4. INSTALLATION REQUIREMENTS

Installing the FINGER007 is a relatively easy task. It can be installed with common hand tools and readily available communications wire. This section provides information about wiring, wire runs and other information to make the installation quick and easy.

4.1 WIRE/CABLE

Good electrical connections will minimize the line losses and avoid damages to the FINGER007 control electronics. Use good quality and proper thickness of wire with durable insulation such as vinyl or PVC. It may be faster and much economical to run multiple, twisted pair cable rather than individual pairs. The following cable and wire thickness from the Belden Master Catalog 885 are adequate for the most FINGER007 applications. These are offered as a reference only.

Belden No. 9745 3 twisted pairs, 22 AWG, 7/30 stranded, unshielded, PVC insulation and jacket,

14.7 ohms/1000 feet (about 300meter). Belden No. 9750 3 twisted pairs, 20 AWG, 10/30 stranded, unshielded, PVC insulation and jacket,

10.3 ohms/1000 feet (about 300meter). Belden No. 8303 3 twisted pairs, 22 AWG, 7/30 stranded, shielded, overall foil/braid shield, PVC insulation and

jacket, 14.7 ohms/1000 feet (about 300meter).

CONDUIT

The FINGER007 does not normally require conduit. However, some location may require conduit for wire protection. Check installation requirements and specifications for your site.

COMMUNICATIONS WIRING

FINGER007 communication is required for using twisted pair wires.

RS232C : 15 meters RS422 : 1200 meters

POWER WIRING

Wires supplying power to FINGER007 may be either twisted or non-twisted pairs. Select the proper wire size to minimize line losses.

OTHER WIRING

Other wiring not mentioned above may be twisted or non-twisted pair wires. This would include wires to door contact sensors, door lock devices and other auxiliary devices. Wire runs should dictate the wire size used. CAUTION : Install a surge absorber or reverse surge protector(diode) at any relay contact that switches DC voltages to an inductive load.

EARTH GROUND

The FINGER007 must be properly grounded to the earth for safety reasons and to prevent damage to the micro-electronics due to electrostatic discharges. The FINGER007 must be connected to earth ground either through conduit, if used, or through a separate ground wire. On-site connection to earth ground can be accomplished through: A earth ground rod, A metal water pipe, The building’s structural steel, A ground grid

20030516 User’s Manual

STAR

FINGER007

5. INSTALLATION

5.1 TEMPLATE

• Tear off last page and use provided template to drill two 6-32 holes and one ½” hole on the proper location

of the wall to mount the Wall Mount bracket as shown below.

(If the gang box is already installed on the wall then skip this step.)

• Using 2 screws, install wall mount to the wall.

* CAUTIONS *

Before mounting the STAR FINGER007 unit to the Wall Mount bracket, an operational test of the unit should be completed, because the locking pins will lock the unit to the Wall Mount. Removing the unit from the Wall Mount bracket after it has been snapped in place may cause damage to the bracket and prevent reattachment.

• Insert 5 O-Rings to the Wall Mount as indicated, then run the cable from the main unit through the center

hole and snap in place the main unit to Wall Mount. Make sure that the main unit is securely locked in place with Wall Mount.

20030516 User’s Manual

STAR

FINGER007

Errore.

5.2 BACKUP BATTERY S/W

FINGER007(of V4.70 or higher) has a S/W(reverse side – Template hole) for the backup battery connection, which is left open circuit to prevent any current consumption of backup battery(Figure : S/W setting). Before the FINGER007 installation, it needs to be connected so that backup battery can retain the memory during power failure.

Figure : S/W SETTING Figure : S/W location

5.3 SYSTEM INITIALIZATION (Extra Reader Port)

You must operate H/W initialization, before the FINGER007 installation. Of V4.70 or higher, you must connect battery backup S/W in reverse side before H/W initialization.

You can H/W initialize using extra reader port. First, turn off the system power and connect 3 wires (pink, cyan and black(GND)), and turn on the system power. Then you can hear “Initialize beep” and display picture.

System Initialize

1 – Yes, 0 - No

System

Initializing...

Master Password

[ _ _ _ _ ]

System is Clear

Remove Wires!!

1. : If you want H/W initializing, enter key <1>.

2. : Enter initial master password(<3141>).

3. : Showing initializing.

4. : After initializing – Main power OFF and separate 3 wire and main power ON again.

5.4 WIRING

5.4.1 POWER

20030516 User’s Manual

STAR

FINGER007

- Connect (+) wire of DC 12V power to +12V(Red wire) terminal.

- Connect GND(-) wire of DC 12V power to GND(Black wire) terminal.

5.4.2 INPUT CONNECTIONS

Exit Button Connection (EXIT)

- Connect one wire from an Exit Button to EXIT(Orange wire).

- Connect the other wire from the Exit Button to the GND(Black wire).

Door Contact Sensor Connection (CONTACT)

- Connect one wire from a Door Contact Sensor to CONTACT(Yellow with Red stripe).

- Connect the other wire from the Door Contact Sensor to GND(Black wire). Auxiliary Input Connection (Applied IN1, IN2)

- Connect one wire from an Auxiliary Input Device to one of the IN1(Green wire), IN2(Green with White stripe).

- Connect the other wire from the Auxiliary Input Device to GND(Black wire).

Figure : INPUT DEVICES CONNECTION

5.4.3 OUTPUT CONNECTIONS

Door Lock (Power Fail Safe) Connection (Relay 1)

- Connect COM port of Relay 1 to + 12V.

- Connect NC port of Relay 1 to (+)wire of door lock device.

- Connect GND port to (-)wire of door lock devices.

Door Lock (Power Fail Secure) Connection (Relay 1)

- Connect COM port of Relay 1 to + 12V.

- Connect NO port of Relay 1 to (+)wire of door lock device

- Connect GND port to (-)wire of door lock devices

Alarm Device Connection (Relay 2)

- Connect COM port of Relay 2 to + 12V.

20030516 User’s Manual

STAR

FINGER007

- Connect NO port of Relay 2 to (+)wire of Alarm devices.

- Connect GND port to (-)wire of Alarm devices

Figure : DOOR LOCK, ALARM DEVICE CONNECTIOIN

CAUTION : Please add one DIODE as shown above. DIODE : Fast recovery DIODE(current : Min. 1A), 1N4001 ~ 1N4007 or similar

5.4.4 READER CONNECTIONS(Extra Reader) Proximity Reader Connection

- Connect (+)wire of the Proximity Reader to +12V(Red wire)

- Connect (-)wire of the Proximity Reader to GND(Black wire)

- Connect Data-0 wire of the Proximity Reader to DATA0(Pink wire)

- Connect DATA-1 wire of the Proximity Reader to DATA1(Cyan wire)

• Compatible Readers(Extra Reader) :

FINGER007/iPFINGER007: Standard 26bit Wiegand Format Proximity Readers Standard 26bit Wiegand + 8bit Burst Format Proximity and keypad Reader FINGER007SR : Standard 34bit Wiegand Format Proximity Reader Standard 34bit Wiegand + 8bit Burst Format Proximity and keypad Reader

• Recommended Readers :

FINGER007 : RF-TINY, RF10/20/30/70/500, RFK101, FGR006, FGR006EX

20030516 User’s Manual

iPFINGER007: iP10/20/30, iPK101

FINGER007SR : SR10/20/30, SRK101, FGR006SRB

STAR

FINGER007

Figure : READER CONNECTION

6. COMMUNICATIONS

6.1 RS232 COMMUNICATION PORT CONNECTION

A 9-pin connector (Serial communication connector, female) is required to connect the FINGER007 to a host computer via RS232 communication Please follow the instructions.

- Connect RS232-TX port of FINGER007 to the pin 2 of the 9-pin connector.

- Connect RS232-RX port of FINGER007 to the pin 3 of the 9-pin connector.

- Connect RS232-GND of Finger007 to the pin 5 of the 9-pin connector.

- Plug in the 9-pin connector to COM1 or COM2 Port of the host PC.

- Install and run FINGER007 Application Software.

6.2 RS-422 COMMUNICATION PORT CONNECTION

6.2.1 RS-422 CONNECTION (STAND ALONE)

RS422/RS232 converter(CNP200) is required to use RS422 communication between the FINGER007 and a host computer. Please follow the instructions.

- Connect RS422-TX(+) of the FINGER007 to RS422-RX(+) port of the converter.

- Connect RS422-TX(-) of the FINGER007 to RS422-RX(-) port of the converter.

- Connect RS422-RX(+) of the FINGER007 to RS422-TX(+) port of the converter.

- Install and run FINGER007 Application Software.

20030516 User’s Manual

- Connect RS422-RX(-) of the FINGER007 to RS422-TX(-) port of the converter.

- Plug in the RS232 9pin connector of the converter to the COM1 or COM2 Port of the PC.

STAR

FINGER007

Figure : RS-422 Communication between FINGER007 and Host Computer

6.2.2 RS-422 CONNECTION (MULTIPLE FINGER007 CONNECTIONS)

RS422/RS232 converter is required to use RS422 communication between multiple FINGER007s and a host computer. Please follow the following instructions.

First, you have to connect all RS422 port of all FINGER007s in parallel.

- Connect RS422-TX(+) of one FINGER007 to RS422-TX(+) of another FINGER007.

- Connect RS422-TX(-) of one FINGER007 to RS422-TX(-) of another FINGER007.

- Connect RS422-RX(+) of one FINGER007 to RS422-RX(+) of another FINGER007.

- Connect RS422-RX(-) of one FINGER007 to RS422-RX(-) of another FINGER007.

Second, you have to connect one of RS422 port of FINGER007 to RS422/RS232 converter.

- Connect RS422-TX(+) of the one FINGER007 to RX(+) port of the converter.

- Connect RS422-TX(-) of the one FINGER007 to RX(-) port of the converter.

- Connect RS422-RX(+) of the one FINGER007 to TX(+) port of the converter.

- Connect RS422-RX(-) of the one FINGER007 to TX(-) port of the converter.

- Plug in the RS232 9pin connector of the converter to the COM1 or COM2 port of the PC.

- Install and run FINGER007 Application Software.

20030516 User’s Manual

STAR

FINGER007

Figure : RS-422 Communication between FINGER007s and Host Computer.

6.3 DIAL UP MODEM

Please, see the Software manual.

6.4 TCP/IP CONVERTER (EXTERNAL VERSION)

Please, see the Software manual.

20030516 User’s Manual

STAR

FINGER007

7. BASIC SETTINGS

In the system ready, LCD

display model name,

current date and time

POWER ON

GENERAL BOOT

INITIAL BEEP( - - - -)

SYSTEM READY

If you turn on the system power after connected 3 wires (pink, cyan and black(GND)), you can enter system initialize mode.

H/W RESET MODE

INITIALIZE BEEP( - - -)

SYS. INITIALIZE ?

ENTER SETUP MENU

SETTINGIN SETUP MODE

END SETTING ?

ID INPUT ?

YES

MASTER ID ?YES

DURESS P/W ?

REGISTERED ID ?

YES

CHECK REGISTERED

ID'S FLAGS

YES

DURESS FLAG

SET

WAIT INITIIAL MASTER P/W

P/W, T/S, Door, Finger, APB etc...

YES

("3141")

RIGHT ?

YES

SYSTEM INITIALIZE

RF_PIN_ENABLE SETTING

WAITING REBOOT

20030516 User’s Manual

YES

RIGHT ?

YES

OUTPUT CONTROL OF EACH

STATUS

You can select output of each status in "setup menu F2"

STAR

FINGER007

7.1 INITIALIZATION OF FINGER007

Before system installation and when you can’t enter setup menu(system error or something wrong) then you have to H/W initialize. You can H/W initialize using extra reader port. Turn off the system power and connect 3 wires (pink, cyan and black(GND)), and turn on the system power. (Ref. 5.3 FINGER007 INITIALIZATION). Initializing will erase all stored data incl. registered IDs event data. Then you have to setting system parameter.

Before first installation, you must H/W initialize.

In case of over V4.70, you must connect battery backup S/W in reverse side before H/W initialization.

System Initialize

1 – Yes, 0 - No

7.2 HOW TO ENTER THE SETUP MENU

Master Password

[3141]

System is Clear

Remove Wires!!

To setup or to change the FINGER007 settings, you have to enter the SETUP MENU first. To do so, press the 8 times <0> key for Master ID(Default setting “00000000”) and <ENT> key and press Master P/W (Default setting “3141”) then you can get into SETUP MENU. There are 4 main SETUP MENU and you first get into [SETUP MENU F1]. You can move to other SETUP MENU by pressing <F1> key for [SETUP MENU F1], <F2> key for [SETUP MENU F2], <F3> key for [SETUP MENU F3] and <F4> key for [SETUP MENU F4]. There are several SUB MENU in the main SETUP MENU and you can scroll up and down the SUB MENU by pressing <4> and <6> key in the main SETUP MENU. If you press <ESC> key then FINGER007 will exit the SETUP MENU then return to normal operation. You can also change the Master ID in the [SETUP MENU F1]. The Master ID for FINGER007SR is 10 times <0> key (Default setting “0000000000” ), and default Master P/W is <3141>.

7.3 DATE AND TIME SETTING

Select [TIME SETTING] in the [SETUP MENU F1] and enter the Year / Month / Date / Hour / Minute / Second / Day(Total 15 digits) as shown below. LCD will display the new Date and Time after the time setting completed but year and day will not be displayed. FINGER007 has 24 hours system and day

20030516 User’s Manual

codes are 1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday and 7 for Saturday. The Master ID for FINGER007SR is 10 digits number (Default setting “0000000000”).

STAR

FINGER007

Master card(PIN)/

FINGER_007 [F1]

MM/DD hh:mm:ss

Initial display

Password/Fingerprint

Initial Master key <00000000>)/

Initial password(<3141>)

Select ‘Time Setting’

TIME SETTING

MM/DD hh:mm:ss

ENT

YYYYMMDDhhmmssW

200107050918305

TIME SETTING

07/05 09:18:30

ESC

FINGER_007 [F1]

Initial display after time setting

: After change Master : Initial Master

à Day code 1 : Sun., 2 : Mon., 3 : Tue., 4 : Wed., 5 : Thu., 6 : Fri., 7 : Sat.

For example, <200106071330253> for Tuesday, June 7, 2001 01:30:25PM.

7.4 ID REGISTRATION

You can register the User ID into FINGER007. Select [SETUP MENU F3] à [ID REGISTRATION] then follow the steps below.

07/05 09:18:30

The Master ID for FINGER007SR is 10 digits number(Default setting “0000000000”).

FINGER_007 [F1]

MM/DD hh:mm:ss

Initial display

ID REGISTRATION

20030516 User’s Manual

Master Card(PIN)/

Password/Fingerprint

Initial Master pin(<00000000>)/

Initial password(<3141>)

ENT

Select ID Registration menu

(Setup menu F3)

ID REGISTRATION

1 - Card, 2 - Key

STAR

FINGER007

Using Fingerprint

Using fingerprint

Registration Key

Display false message, and return

1. Registration by RF Cards (FINGER007 only)

<1>Key

(FP:1)

Put ID CARD

Scanning…

Not using Fingerprint (FP:0)

To Register FP

Put Your FP On..

Input fingerprint first time

False

Approach card

reader1

success

Waiting…

Input fingerprint second time

Display false message, and return

Registration mode.

2. Registration by Keypad (FINGER007 & FINGER007P)

<2>Key

Key InPut ID

à ¦ ________

Input

Not using fingerprint (FP:0)

Lift and Put FP

25500100

PW1234 TS00 RD3 FPX

Input PW/TS/RD/FP

success

completion

False

00000100

PW1234 TS00 RD3 FPX

Input PW/TS/RD/FP

Success

Completion

(FP:1)

To Register FP

Put Your FP On..

Input fingerprint first time

False

Registration mode.

Success

Lift and Put FP

Waiting…

Input fingerprint second time

False

3. After ID Registration complete, return initial display by enter <ESC> Key.

4. When register more than one ID, register first ID and continuously register other IDs.

5. If the ID number has a fingerprint already, in case of re-registration, the current fingerprint should be scanned first.

6. You can’t register using RF card in FINGER007P.

20030516 User’s Manual

STAR

FINGER007

• The [ID] is Personal Identification Number What you can use RF Card or Keypad. In case of RF Card,

ID number consists of 3-digits Facility code from 000 to 255 and 5-digits ID number form 00000 to 65535 so that the 8-digits ID number can not exceed 25565535. But, in case of Keypad, you can use 4 ~ 8 digit for ID number. (ID number of FINGER007SR has 10-digits decimal numbers.)

• The [PW] is for password input the password is needed to access doors when the controller is

operating in RF+Finger(P/W) or RF+P/W+Finger mode. But regardless of the operating mode, it is necessary to input a password when registering.

• The [TS] is Time Schedule code (00-10). [TS] is the Time Schedule for the Main Reader, Extra Reader.

When you present the card to Reader then the cardholder is only allowed the access of the door during the Time Schedule code entered to TS__ . To control the accessible Time Schedule for each cardholder, you must setup the Time schedules first and enter the Time Schedule code here. If you want to access the door anytime for the cardholder then enter default Time Schedule code '00' for the value.

• The [RD] is reader usage codes for the cardholder. If you put ‘1’ for RD then Main Reader is accessible

and if you put ‘0’ for RD then the cardholder can not access through the Main and Extra Reader, and FINGER007 generates an error message “Access Door Error!” and displays on the LCD. To get access through all Readers, you have to input “3” value for RD.

• The [FP] is for using fingerprint. If “1” is entered for the value, the user has to register fingerprint. And

the user certification of fingerprint in RF+Finger(P/W) and RF+P/W+Finger mode. If “0” is entered for the value, fingerprint substitute by password.

20030516 User’s Manual

STAR

FINGER007

8. OPERATION

8.1 NORMAL OPERATION

Power ON

When the Power is applied to FINGER007, the RED LED is turned on.

Registered Card Reading

When a registered card (or PIN) is read, the Door(Relay 1) will open for 3 seconds(Defaults) with the Green LED on.

Exit Button

To request for exit from the inside, an Exit Button(or Extra Reader) can be used. The Door(Relay 1) will open for 3 seconds(Defaults) with the GREEN LED on.

Alarms (unregistered/password/fingerprint/time schedule/door ERROR)

When an unregistered card is read, wrong password is input, wrong fingerprint is input, over the time schedule, and access wrong door, the access is denied and the alarm(Relay 2) will be activated for 3 seconds(Defaults) with RED LED on.

8.2 DEFAULT SETTING

When you operate the FINGER007 first time or you initialize the FINGER007, the controller will setup all values defaults (factory settings). You can change the settings for desired application. Please refer to the APPENDIX for the default setting values.

20030516 User’s Manual

STAR

FINGER007

9. SETTING CHANGES

INITIAL DISPLAY

(MODEL NAME, CURRENT TIME)

ID INPUT?

YES

MASTER ID /PW/

FINGERPRINT ?

YES

SETUP MODE

SETUP F1 MODE SETUP F2 MODE SETUP F3 MODE SETUP F4 MODE

1. MODE SELECTION

2. TIME SETTING

3. TYPE SELECTION

4. APB SETUP

5. COMM ID SETTING

6. DURESS MODE SET

7. BAUD RATE

8. EVENT CLEAR

9. MASTER ID CHANGE

10. SYS INITIALIZE

11. ID CLEAR

12. TIME SCHE CLEAR

13. RF_PIN_INPUT

1. TIME SCHEDULE

2. HOLIDAY T/S

3. IN/OUT DEFINE

4. HOLIDAY INDEX

5. MODE INDEX

6. LCD DISPLAY

7. OUTPUT TIME

1. ID REGISTRATION

2. ID DELETE

3. ID LIST

4. ID COUNT

5. EVENT COUNT

OPERATE GENERAL

MODE

1. F/W VERSION

2. SRAM TEST

3. OUTPUT TEST

4. LCD TEST

5. KEYPAD TEST

6. READER TEST

7. INPUT TEST

8. COMM TEST

9. GET GAIN IN FDA

10. SET GAIN IN FDA

. To setup or to change the FINGER007 settings, you have to enter the SETUP MENU first. To do so, input Master

ID(Default setting “00000000”), input Master P/W(Default setting “3141”) and input Master Fingerprint then you can get

into SETUP MENU. There are 4 main SETUP MENU and you first get into [SETUP MENU F1]. You can move to other

SETUP MENU by pressing <F1> key for [SETUP MENU F1], <F2> key for [SETUP MENU F2], <F3> key for [SETUP

MENU F3] and <F4> key for [SETUP MENU F4]. There are several SUB MENU in the main SETUP MENU and you can

scroll up and down the SUB MENU by pressing <4> and <6> key in the main SETUP MENU. If you press <ESC> key

then FINGER007 will exit the SETUP MENU and return to normal operation.

The Master ID for FINGER007SR is 10 times <0> key(Default setting).

20030516 User’s Manual

STAR

FINGER007

9.1 SETUP MENU F1

Seach Key

MODE SELECTION

RF+FINGER(P/W) (ID+FINGER(P/W))

Seach Key <4>,<6>

TIME SETTING

Seach Key

TYPE SELECTION STAND ALONE USE/NOT USE

Seach Key

RF+P/W+FINGER (ID+P/W+FINGER)

RF Only (ID Only)

FINGER007P

USE/NOT USE

USE/NOT USEUSE DUAL FINGER

USE/NOT USEADAPTIVE MODE

USE/NOT USEIDENTIFICATION

APB SETUP NOT USE/USE/ALL CLEAR

Seach Key

20030516 User’s Manual

STAR

FINGER007

Seach Key

DURESS MODE SET USE/NOT USE

USE

Seach Key

DURESS P/W

BAUD RATE 4800/9600(DEFAULT)/19200

Seach Key

EVENT CLEAR

MASTER ID CHANGE

Seach Key

SYSTEM INITIALIZE YES/NO

Seach Key

ID CLEAR YES/NO

Seach Key

TIME SCHE CLEAR YES/NO

Seach Key

YES/NO

20030516 User’s Manual

RF_PIN_INPUT

ENABLE/ DISABLE

STAR

FINGER007

> NOT USE

> USE

You can select whether the anti

pass

back(APB) mo

de is used or

Press

<4>

<6>

to toggle the mode, from

NOT USE

USE

or the

. When the cursor is blinking, enter a new ID(Two Digit number), then the

9.1.4 ANTI-PASS-BACK MODE SETTING

APB SETUP NOT USE

APB SETUP

--> All Clear

NOT USE : Anti-pass-back mode is not applied. USE : Anti-pass-back mode is separately applied. All Clear : Ignore all registered ID’s APB flag only once.

not. To change mode, press <ENT> key. (It only applies when the Door has Exit Reader)

reverse, and finish selecting by pressing <ENT> key.

9.1.5 COMMUNICATION ID(ADDRESS) DISPLAY

COMM ID SETTING

COMM ADDRESS

COMM ADDRESS 01

. This is communication ID setting menu.

To change the communication ID, press <ENT> key.

. The number on the LCD is the current communication ID(Device NO.)

Press <ENT> key again to set a new communication ID.

setting is completed.

Possible ID is between 00 ~ 31 inclusive.

20030516 User’s Manual

STAR

FINGER007

, then system display current DURESS P/W. To change

: You can setting duress output in setup menu F2(in/out define). In

and

g general process. If you registered ID, then duress

9.1.6 Setting Duress Mode

DURESS MODE SET NOT USE

'ENT'

Seach key <4>,<6>

USE

If you select <USE>

DURESS P/W

DISPLAY CURRENT P/W

'ENT'

ENTER NEW P/W

( 2DIGIT)

DURESS MODE SET NOT USE

. You can select whether the Duress mode is used or not.

To change mode, press <ENT> key.

DURESS MODE SET

--> USE

DURESS P/W 00

DURESS P/W 99

. If you select USE

P/W, press <ENT> key.

NOTE

case of Duress, enter the 2 digit Duress Password and press <ENT> open the door usin output will be generated.

20030516 User’s Manual

STAR

FINGER007

9600

--> 9600

--> 19200

supports 4800, 9600 and 19200 of baud rate and default

setting is 9600bps. Wrong baud rate setting will cause communication

and host PC. If

select desired baud rate

key then

events is not necessary to upload to the host PC

9.1.7 BAUD RATE SETTING

BAUD RATE

9.1.8 EVENT CLEAR

EVENT CLEAR

1 – YES, 0 - NO

. FINGER007

errors and you have to set same baud rate to FINGER007 you have communication problem, please check followings;

- Check COMM ID of FINGER007 and host PC

- Check BAUD RATE of FINGER007 and host PC

- Check communication port and cable

- Check COM port setup of host PC Parity: None, Data Bit: 8 bit, Stop Bit: 1 bit

To change the baud rate, press <ENT> key and

by pressing <4> or <6> key then press <ENT> key.

. You can clear the event memory in this menu. Press <ENT> press <1> key to clear event memory or <0> key to cancel the operation

CAUTION : Before you clear the events, make sure that the stored

otherwise you may lose important data.

20030516 User’s Manual

STAR

FINGER007

key, if an

initialization is needed. (First time installation or resetting in the event of a

ser ID

from the memory. Press <ENT> key then press <1> key to clear all User ID

Before you clear all User ID, make sure that the registered

you may lose all registered

MASTER ID CHANGE WAITING NEW MASTER CARDCARD

MASTER ID CHANGE

KEY

WAITING NEW MASTER ID

(MASTER ID : "00000000"

P/W : "3141")

9.1.10 SYSTEM INITIALIZE

SYS INITIALIZE

Sys Initializing

1 – Yes, 0 - No

System

Initializing …

9.1.11 CARD ID CLEAR

CARD ID CLEAR

Card ID Clear

1 – Yes, 0 - No

EXIST MASTER ID? YES

WAIT NEW MASTER FINGERPRINT

(FIRST TIME, SECOND TIME)

SUCCESS?

YES

ENTER NEW MASTER P/W

END MASTER ID CHANGE

YES

CERTIFICATION OLD MASTER

SUCCESS?

. This operation will initialize the FINGER007. Press <ENT>

malfunction)

After the initialization, FINGER007 will return to the setup menu.

CAUTION : Initializing will erase all stored data in the memory.

(ID, EVENT, T/S, In/Out define, etc...)

. When you want to delete all User ID (Card ID), you can clear all U

or <0> key to cancel the operation.

CAUTION :

User ID is no longer used otherwise User ID.

20030516 User’s Manual

STAR

FINGER007

. You can enable

PIN(card number) to be input

through the keypad,

, must be replaced

with a new Master card number before disabling keypad input, or you

When you want to delete all

Time

Schedule (01~1

), you can clear all T/S

from the memory. Press <ENT> key then press <1> key to clear all T/S or

Before you clear all T/S, make sure that the stored T/S

9.1.12 TIME SCHEDULE CLEAR

TIME SCHE CLEAR

Time Sche Clear

1 – Yes, 0 - No

9.1.13 KEYPAD INPUT SETTING

RF_PIN_INPUT

ENABLE

RF_PIN_INPUT

--> DISABLE

<0> key to cancel the operation.

CAUTION :

is no longer used otherwise you may lose all stored T/S in the

memory.

that someone who doesn't carry RF cards with him can access the door. When it is disabled, accessing the door by keypad will be denied.

Press <ENT> key to toggle the mode.

CAUTION: The default Master number, “00000000”

CANNOT access the setup menu again.

In case of that, the only thing you can do is hardware initializing.

Do not use this menu in FINGER007P.

20030516 User’s Manual

STAR

FINGER007

INDEX : 01 ~ 10

9.2 SETUP MENU F2

Seach Key

TIME SCHEDULE

Seach Key

HOLIDAY T/S

Seach Key

IN/OUT DEFINE

Seach Key

HOLIDAY INDEX

Seach Key

MODE INDEX

WEEKLY : HOL, SUN, MON,.., SAT NO. : 01 ~ 05

INDEX : 01 ~ 10 NO. : 01 ~ 32

01 : EXIT OUTPUT 02 : DOOR CONTACT OUTPUT 03 : AUX1 OUTPUT 04 : AUX2 OUTPUT 05 : TAMPER OUTPUT 06 : R1 ID OK OUTPUT 07 : R1 ID ERROR OUTPUT 08 : R1 ID T/S ERROR OUTPUT 09 : R1 APB ERROR OUTPUT 10 : R2 ID OK OUTPUT 11 : R2 ID ERROR OUTPUT 12 : R2 ID T/S ERROR OUTPUT 13 : R2 APB ERROR OUTPUT 14 : DURESS MODE OUTPUT 15 : OUTPUT T/S 16 : IN/OUT T/S

Seach Key

LCD DISPLAY

Seach Key

OUTPUT TIME

Status Card No.

1 SEC

0.1 SEC

20030516 User’s Manual

STAR

FINGER007

?. Possible values for time scheduling

You may program time schedules to grant and restrict access for each

user. There can be up to ten different schedules. A minimum of one

If only one schedule is programmed the most common setting allows

4 hours / day. A time schedule can be programmed

for each day of the week and holidays, and five shifts can be defined for

10)

Sun and ‘HOL’). Define which shift of the

key. ‘HOL’ refers to specific

key, and the cursor will blink,

digit) and the ending time in the same form. Then the

lower line will indicate the defined period. For more schedules, repeat

9.2.1 REGISTERING AND CHANGING TIME SCHEDULE

TIME SCHEDULE DISPLAY CURRENT T/S

'ENT'

SELECT T/S NUMBER AND INDEX

(USE "2","8","4","6"KEY)

'ENT'

(START TIME(hh:mm) - END TIME(hh:mm))

ENTER T/S (8 DIGIT)

YES

'ESC'

COMPLETION

TIME SCHEDULE

? .

schedule must be defined.

access for all users 2

each day. To set time schedules, press <ENT> key from this menu.

If you want to set time schedules, press <ENT> key when this figure displayed.

T/S : 01 HOL : 1

00:00 - 00:00

. Press <2> key or <8> key to adjust the Time Schedule (T/S) number (1-

and the day of the week (Monday (1-5), using the <4> key and <6> holidays you will register. Press <ENT> then enter the beginning time of the period, in the form of hour(2digit):minute(2-

the process. To end time scheduling, press <ESC> key.

1) Time schedule number : 01 ~ 10 (Needed when IDs are registered)

2) A day of the week : MON, TUE, WED, THU, FRI, SAT, SUN, HOL

3) Index : 1 ~ 5(referred to the five periods of time of a day)

20030516 User’s Manual

STAR

FINGER007

. 1)

Holiday Time schedule(Date registration set) number : 01 ~ 10(10 years)

You can register up to 32 specified “holidays,” per year for each schedule

setting. There can be 10 other registration sets created, meaning holidays

With

<2>

key and

<8>

key, select the date registration set number (1~10), and

elect the index for the days (1~32). Then, press

key, and the cursor will blink, then enter the date, in the form of Month

(1~12):date, Then the LCD will indicate the defined date. Now, a day has been

9.2.2 REGISTERING AND CHANGING HOLIDAY TIME SCHEDULE

HOLIDAY T/S DISPLAY CURRENT T/S'ENT'

YES

'ESC'

SELECT T/S NUMBER AND INDEX

(USE "2","8","4","6"KEY)

ENTER T/S (4 DIGIT)

COMPLETION?

'ENT'

(MM:DD)

HOLIDAY T/S

HOL T/S : 01 #01 00:00

can be set for up to 10 years. Press <ENT> to register the days.

with <4> key and <6> key, s

<ENT>

registered. For further registration, repeat the process.

2) Index for the days : 01 ~ 32(32 days)

20030516 User’s Manual

STAR

FINGER007

9.3 SETUP MENU F3

Search key

ID REGISTRATION

Search key

ID DELETE

Search key

ID LIST

Search key

SELECT REGISTRATION METHOD

(FINGER007)

ENTER ID NUMBER (4 ~ 8 digits)

(FINGER007P)

CARD or ID INPUT(KEY PAD)

(FINGER007)

ID INPUT(KEY PAD)

(FINGER007P)

DISPLAY ID, PW, TS, DOOR and

FINGERPRINT FLAG

CARD/KEY

KEY

CARD/KEY

KEY

ID COUNT

Search key

EVENT COUNT

DISPLAY REGISTERED ID COUNT

DISPLAY STORE EVENT COUNT

20030516 User’s Manual

STAR

FINGER007

9.3.1 CARD REGISTRATION

ID REGISTRATION

FINGER007

FINGER007P

YES

SELECT REGISTRATION METHOD

(FINGER007)

CARD or KEY ?

KEY

ENTER NEW ID

(4 ~ 8 Digits)

MASTER ID ?

INPUT

P/W, T/S, DOOR and FINGERPRINT

flag

USE FINGERPRINT ?

YES

ALREADY EXIST ID ?

YES

CARD PRESENT CARD

CERTIFICATION ID's FINGERPRINT

SUCCESS ?

YES

REGISTRATION NEW ID's

FINGERPRINT

(First time)NO

SUCCESS ?NO

REGISTRATION NEW ID's

FINGERPRINT

(Second time)

SUCCESS ?

YES

COMPLETION ID REGISTRATION

20030516 User’s Manual

STAR

FINGER007

1) PW(password) :

he password used in RF

+ fingerprint(

password

) and RF + password + fing

erprint

mode.

: To register a fingerprint for the ID number being registered.(If the ID number has a fingerprint

is set to operate in

key, the

is waiting for an RF card which is to be registered. And In case register

for the FP flag to register a fingerprint for the ID number, you will

rprint input window.

As the fingerprint should be scanned twice, Put a finger to the window, according

: 1. The fingerprint registration needs two a little different images of a

fingerprint. For that reason, after the first scan, the finger must be lifted off

registered for changing

ID REGISTRATION

? . ID number is registered in the FINGER007 by RF cards or through the keypad. For RF cars, Press <1>

keypad, <2> key, or you can quit the registration by pressing <ESC> key.

FINGER007 - Over V4.70 : 4 ~ 8 Digits.

CARD & Key Use

1 – CARD, 2 - Key

Put ID CARD

Scanning …

Key Input ID à : ¦ _______

XXXXXXXX PW____TS__RD_FP_

XXXXXXXX

ID Registered

To Register FP

Put Your FP On ..

Lift and Put FP

Waiting ...

Under V4.70 : 4 Digits.

FINGER007SR - 4 ~ 8 Digits.

. In case register by RF card, FINGER007

by keypad, you can register 4 ~ 8 digits ID.

* CAUTION :

Under V4.70 : In case register by keypad, you have to enter only

4digits ID.

This figure appears, indicating the ID number you just entered on the upper line, and you are to enter the following information for the ID number : Four-digit password, two-digit Time Schedule number, Reader number(see the NOTE below) and FP flag(enter <1> to register a fingerprint, <0>, not to.). If you enter <0> for the FP flag, the message ‘ID Registered’ will be shown for a moment and the controller waits for another PIN number to be input. You can register other PINs in the same way. Press <ESC> key to quit the registration. (You can change the TS, the RD and the FP flag in the same way as the new registration)

If you enter <1>

see this figure showing and the red light fleshing in the finge

to the message displayed, lift the finger off briefly and put it again.

NOTE

briefly. 2. When a ID number using fingerprint is reoptions, the current fingerprint is needed to be scanned.

2) TS(Time schedule) 00 : Anytime accessible 01 ~ 10 : Accessible according to each T/S index

3) RD(Reader code) 1 : for using reader 1 alone 2 : for using reader 2 alone, 3 : for using both reader 1 and 2.

4) FP(Fingerprint flag)

already, in case of re-registration, the current fingerprint should be scanned first.)

0 : When the ID don’t need a fingerprint registered. If the controller

RF+FINGER(P/W) or RF+P/W+FINGER mode, it will operate in RF+P/W(Password)mode.

20030516 User’s Manual

STAR

FINGER007

key in this

message will be displayed when there is no

r ID, 4 digit password, the applied T/S, reader

code and fingerprint flag are displayed on the LCD, and you can scroll up

key to return

first when the first registered

message will be displayed first when the last

This menu displays the total number of registered user ID count. It

9.3.3 ID LIST

ID LIST

MEMORY EMPTY

XXXXXXXX

XXXX XX XX X

ID List TOP

ID List BOTTOM

. If you want to see the list of registered user ID, press the <ENT> menu.

“MEMORY EMPTY”

registered user ID.

From four to eight digit use

and down the list by pressing <4> and <6> keys. Press <ESC> to the setup menu.

“ID LIST TOP” message will be displayed

user ID is displayed on the LCD.

“ID LIST BOTTOM”

registered user ID is displayed on the LCD.

9.3.4 REGISTERED ID COUNT

ID COUNT XXXX

9.3.5 STORED EVENT COUNT

EVENT COUNT XXXXX

automatically counts when you register or delete user ID.

. This menu displays the total number of stored event count.

20030516 User’s Manual

STAR

FINGER007

9.4 SETUP MENU F4

Search key

F/W VERSION

Search key

SRAM TEST

Search key

OUTPUT TEST

Search key

LCD TEST

Search key

KEYPAD TEST

Search key

READER TEST

Search key

DISPLAY CURRENT F/W VERSION

SRAM TEST

OUTPUT TEST

LCD TEST

KEYPAD TEST

READER TEST

(FINGER007)

DO NOT USE THIS MENU

(FINGER007P)

INPUT TEST INPUT TEST

Search key

COMM TEST COMMUNICATION TEST (RS-232)

Search key

GET GAIN IN FDA CHECK FINGERPRINT DARKNESS

Search key

SET GAIN IN FDA SET FINGERPRINT DARKNESS

20030516 User’s Manual

STAR

FINGER007

<4>

problems, LCD will show the memory block number

message. In this case, you have to contact technical

9.4.1 VERSION CHECK

F/W Version X.XX

9.4.2 SRAM TEST

SRAM TEST

Memory fail !!!

RAM testing …

RAM test pass !!!

Press any key …

. The version of the controller’s firmware is displayed on the LCD. Press

or <6> key to look for other menus of setup menu F4.

. To test the SRAM memory, press <ENT> key.

If the SRAM has with “Memory fail!!!” support.

If the SRAM is working properly then LCD will show “RAM test pass!!!” message.

9.4.3 OUTPUTS TEST

OUTPUT TEST

'ENT'

RELAY 1 TEST

(Activated two times)

RELAY 2 TEST

(Activated two times)

TTL OUTPUT1 TEST

(Activated two times)

TTL OUTPUT2 TEST

(Activated two times)

BUZZER OUTPUT TEST

(Activated two times)

OUTPUT TEST END

This test is applicable to Relay1 and green LED

This test is applicable to Relay2 and green LED

This test is applicable to TTL1 (0V ~ 5V)

This test is applicable to TTL2 (0V ~ 5V)

This test is applicable to Buzzer.

20030516 User’s Manual

STAR

FINGER007

As the test proceeds several characters will move quickly from right to left.

the keys on the keypad will

To test the output performances, press

<ENT>

key

If the output

, the green LED blinks twice as the relay is being shorted and opened

, the yellow LED blinks twice as the relay is being shorted and

s no other

OUTPUT TEST

OUTPUT 5 Press any key …

9.4.4 LCD TEST

LCD TEST

Last Update XXXX/XX/XX

9.4.5 KEYPAD TEST

KEYPAD TEST

0123456789ABCDEF

performance has no problems, the test will proceeds as follows :

First

twice. The relay ticktack as it works, you can hear the sound.

Second

opened twice. The relay ticktack as it works, you can hear the sound.

Third, the LCD changes its figure, <ON, OFF, ON, OFF>. There’

presentation you can see.

Fourth, the buzzer beeps twice.

. To test the performance of LCD, press <ENT> key.

. Press <ENT> key to start the keypad test.

When operating normally, pressing

display the corresponding letter on the LCD.

Note : The letters on the LCD, A, B, C, D, E and F are referred to <F1>, <F2>, <F3>, <F4>, <ESC> and <ENT>key, respectively.

20030516 User’s Manual

STAR

FINGER007

Card No.

Reader No.

CD displays the ID card

232 RX, TX wires

If there is a problem with the communication performance, check

9.4.6 READER TEST

READER TEST

Scanning …

. To test the performance of the reader, press <ENT> key.

NOTE : In case FINGER007P, you don’t using this menu.

The reader is waiting for an RF card to read. Present an RF card to the reader. The test has completed successfully if the L number(example shown to left)

Reader 1

XXXXXXXX

9.4.7 INPUT TEST

INPUT TEST

1 1 1 1 1

9.4.8 COMMUNICATION TEST

COMM TEST

TX data = 0 COMM fail

COMM test pass !!

Press any key …

. To test performance of input ports, press <ENT> key.

The lower line on the LCD indicates the status of the five input signals.

Note:

1. Input 1~4 − <1> : No input signal, <0> : Exist input signal

2. Input 5 − <0> : No input signal, <1> : Exist input signal

. To test performance of input ports, press <ENT> key.

(Before this communication test, connect the RS-

to each other.)

connections and try again.

As the test proceeds, you can see the characters being transmitted an received. Finally LCD display communication test pass message.

20030516 User’s Manual

STAR

FINGER007

: Fingerprint darkness gain and fingerprint certification ration is not

an adjust the fingerprint darkness at this menu. Press <ENT> key to

9.4.9 CHECK FINGERPRINT DARKNESS

GET GAIN in FDA

9.4.10 SET FINGERPRINT DARKNESS

SET GAIN in FDA

. You can see the current fingerprint darkness for scan.

The gain is the higher, scan fingerprint is the dark.

CAUTION

always direct proportion.

. You c

adjust the fingerprint darkness. You can 1,2,4(default) or 8 as the value.

20030516 User’s Manual

STAR

FINGER007

APPENDIX

A. THE RELATION BETWEEN INPUT AND OUTPUT(DEFAULT)

1. The relation between input and output

Index No Relay #1 Relay #2 TTL1 TTL2 BUZZER

[1] Exit Button [2] Door Contact 00 [3] AUX 1 00 [4] AUX 2 [5] Tamper S/W 00 [6] Reader1 ID OK [7] Reader1 ID Error 00 [8] Reader1 ID T/S Error 00 [9] Reader1 APB Error 00 [10] Reader2 ID OK [11] Reader2 ID Error 00 [12] Reader2 ID T/S Error 00 [13] Reader2 APB Error 00 [14] DURESS MODE [15] OUTPUT TIME SCHEDULE 00 00 00 00 00

[16] INPUT TIME SCHEDULE

Exit Contact AUX 1 AUX 2 Tamper

00 00 00 00 00

* Index No. [1] ~[14] : The value indicates operation time (second) of each output for the input signal. * Index No. [15] : The value indicates time schedule code (index) that each output operation is to be applied. * Index No. [16] : The value indicates the time schedule code (index) that each input:1 (Exit button) ~ 5(Tamper S/W) operation is to be applied.

00 00 00 00

03 03 03 03 03 03 03 03

99 99 99 99

00 00 00 00

03 03 03

00 00 00 00

03 03 03

00 00 00 00 00 00 00 00 00

00 00 00 00 00 00 00 00 00 03 03

20030516 User’s Manual

STAR

FINGER007

B. TROUBLE SHOOTING

? Broken or abnormal letters show on the LCD, when powered on.

Cause Of troubles of its battery in charge of the internal back-up or of circuits near around

Solution 1. Initialize the controller referring “hardware initialization of the manual”

2. Set the current time in Set-Up menu of F1 and turn its power off and on again.

3. If the problem remains after performing 1, 2 of the above, please contact designated service center.

? Unable to enter set-up mode with MASTER ID (default value:‘00000000’) and P/W(default value: ’3141’)

(cf. In case FINGER007SR, master ID consists 10digits character. Default ID “0000000000”)

Cause

Solution 1. Check Master ID and Master P/W.

Of internal element error, of unconsciously changed Master ID or of Set-up error

Try changing the RF_PIN_ENABLE setting to “ENABLE” through the application S/W.

Try changing the Master ID and P/W through the application S/W.

2. When it is not feasible, initialize the unit in the light of the manual.

Check Backup BAT S/W (Mount hole in the reverse side. Of V4.70 or higher)

- It must be placed “ON”.

* Note that all the value will be set to default, including the IDs after initializing.

3. If the trouble remains after the procedure above, contact a designated service center.

? Randomly changed value of in/out define from previously setting value after power reset.

Cause Discharge of RAM Back-Up battery problem during the main power off.

Solution 1. Check Backup Battery S/W : It must be placed ON. (Of V4.70 or higher)

2. Check if the voltage of Back-Up Battery is over 3.6V..

3. If it is over 3.6V, make initialization process as below.

- Turn off the system power and connect 3 wires (pink, cyan and black(GND)).

20030516 User’s Manual

- Turn on the system power. Then you can enter system initialization mode. Enter <1>key,

then system is initializing.

- After initializing, keep the main power on more than 5 days.

* Aware that all the setting value be back to the default value and data memory be clear.

(ID data clear/Event data clear/ Time Schedule data clear etc.)

4. If after all the above, the problem remains, please contact a designated service center.

STAR

FINGER007

? “ACCESS DOOR ERR” message shows when the RF ID card is read.

Cause Incorrect user setting or false of internal circuit.

Solution 1. If it is of properly operating unit before, there has been electric shock that damaged internal memory

and data. Please initialize the unit as instructed in the manual.

2. Check if ID information is put incorrectly during its registration.

* Register ID again checking the following points.

- Since the controller has two reader ports, define “RD” – door for the user to be allowed to access.

Reader1 only(Main reader) : “1”, Reader 2 only(Extra reader) : “2”, Reader 1 & 2 both: “3”

- If RD is set as “1”, only when the card is read at reader 1, the door opens but not at reader2. If it is

read at reader 2, “ACCESS DOOR ERROR” message shows.

- If RD is set as “2”, only when the card is read at reader 2, the door opens but not at reader1. If it is

read at reader 1, “ACCESS DOOR ERROR” message shows.

- If RD is set as “3”, reader 1 & 2 both opens each door.

3. Use software for time schedule setting in case it is connected to PC as the software manual.

4. If the trouble remains after checking the above, contact a designated service center.

? “SCHEDULE ERROR” message shows when RFID card is read.

Cause Error in RFID card registration, time schedule setting or the system itself.

Solution 1. If it is of properly operating unit before, there has been electric shock that damaged internal memory

and data. Please initialize the unit as instructed in the manual.

2. Check if ID information is put incorrectly during its registration.

* Register ID again checking the following points.

-In order to restrict access of the ID user for specific time zone as instructed in the manual, register

time schedule in advance and apply the time schedule code(1~10) in the registration of the user ID.

- In order to allow the user to access at all times put “00”.

3. Use software for time schedule setting in case it is connected to PC as the software manual.

4. If the trouble remains after checking the above, contact a designated service center.

20030516 User’s Manual

STAR

FINGER007

? A valid card became unregistered after batch-downloading IDs from PC.

Cause Wrong procedure during download, or a component defect.

Solution 1. The card ID might be registered only to the controller and not registered in PC. The process of

downloading IDs, FINGER007 first erase the ID memory of the unit, therefore if the IDs from the PC

didn’t contain the card ID, this can happen.

2. Check whether the card ID is registered in PC

3. If not, please register the number and try downloading again.

If the trouble remains after the procedure above, contact a designated service center.

? The controller does not communicate with PC.

Cause Defective cable is used, errors in wiring, an error in setting COMM ID of the controller, or damage on the

communication port (either on PC side or on the controller side).

Solution 1. Please, check the settings of the application S/W and the controller.

- Check the controller’s COMM ID is listed on the application S/W.

- Set the different COMM ID when two or more controllers are installed.

- Check the communication speed(Default 9600bps) is the same as the setting on the S/W.

- Make sure that the PC’s COM port is set correctly on the S/W.

- The parameters at the S/W should be set as follows.

Parity bit : NONE

Data bit : 8bit

Stop bit : 1bit

2. Check the line connection for communication

FINGER007

RS232 RS422( )

PC FINGER007

RX TX RX(-) TX(-)

TX RX RX(+) TX(+)

GND GND TX(-) RX(-)

TX(+) RX(+)

RS422(Multi Drop)

FINGER007 FINGER007

RX(-) RX(-) TX(-)

RX(+) RX(+) TX(+)

TX(-) TX(-) RX(-)

TX(+) TX(+) RX(+)

RS232/422

Converter

RS232/422

Converter

The RS232 cable from the converter.

The RS232 cable from

the converter

20030516 User’s Manual

STAR

FINGER007

3. In case of setting RS422 communication, recommend to use line-end resistors of 120 Ohm between the RX(+) and RX(-) lines and between the TX(+) and TX(-) lines, and apply the same resistors to the converter RS422 lines. Consult a service center or an electric technician if you cannot be sure how to do it.

4. When a multi-drop communication doesn’t work, test one-by-one communication first.

5. If the trouble remains after the procedure above, contact a designated service center.

20030516 User’s Manual

STAR

FINGER007

? Keep making buzzer sound: “beep~ beep ~ beep” or “beep~~~~”.

Cause Error in installation, door status or internal circuits.

Solution 1. Check the door status. It occurs in case that the door is opened over 20 sec after the proper door

open time.

2. Check the door contact sensor type: it should be NO type.

3. Check in “IN/OUT DEFINE” of F2, the fifth Time schedule code(01~10) value of 15 output T/S. If the

time schedule code is set between 01-10 and if the present time is included in the schedule.

If it is set to unintended value, change it to “00” ( Programmable via PC software)

4. If the trouble remains after checking the above, contact a designated service center.

? The extra reader seems to read cards, but the controller does not respond or does not respond properly, such as displaying wrong card numbers in the reader test mode.

Cause Reader defect, wiring error between the reader and the controller, or the electric noises around.

Solution 1. Be sure that the reader reads the card ID when you present a card.

2. Be sure that the reader format is correct. 26bit Wiegand or 34bit Wiegand for FINGER007SR.

3. Check the wiring between the reader and FINGER007.

- Check the wires of Wiegand data lines D0 and D1 which is connected correctly.

- Connect the controller ground to the ground wire of the reader and it is recommended to

connect them to an earth ground.

4. Using oscilloscope, check the shape of signals from the reader at the controller’s side.

When noises are shown on the signals, it is recommended to use shielded wires and the unused

wires to the common ground. You can use repeaters, also.

5. Check the maximum cable length, which may be indicated on the reader manual.

6. If the trouble remains after the procedure above, contact a designated service center.

? No problem with accessing by cards, but cannot access with the PIN input.

Cause An error in Setup or possible component defect.

Solution 1. Check whether a beep sound is generated when you press a key.

When it is, the problem may be an error in setup. Proceed followings.

- Enter the Master ID(“00000000” default), P/W(“3141” default) and Fingerprint to enter the Setup

mode. (Note that the default Master ID for FINGER007SR is 10 times <0>, “0000000000”.)

20030516 User’s Manual

- Press <F1> key.

- ‘MODE SELECTION’ will appear on the LCD, then use the key <6> to choose ‘RF_PIN_INPUT’

and select ‘Enable’ as wanted.

2. When there is no beep sound or already enabled Key-in functions, contact a designated service

center.

STAR

FINGER007

? “Fingerprint error” shows in the LCD repeatedly during fingerprint registration.

Cause Of that fingerprint is damaged, fingerprint is extremely dried or the fingerprint module is defective of the

device.

Solution 1. Of fingerprint registration, it read a fingerprint twice. If the first one and the second one are perfectly

accord, its registration fails. After the first fingerprint reading, take the finger out and put again on

the fingerprint reading window.

2. If the fingerprint is extremely dry or seriously damaged, it can not find its specifications. Of version

4.00 or over, get into the setting mode, F1, TYPE SLECTION and change ADAPTIVE MODE “USE”

and then try again its fingerprint registration. (ADAPTIVE MODE “USE” provides more delicate

reading of fingerprint but it delays a little more than normal.)

3. If the problem remains after performing 1, 2 of the above, it could be of fingerprint module defect or

the device defect, please contact IDTECK service center

? “Door Closed”& CONTACT MASTER“ it shows on LCD with buzzer sounds after card reading.

Cause Of setting error, P/W deletion, defect of internal elements

Solution 1. Check the communication status. If the communication of the device with PC is normal and this

problem occurs, check if the yellow LED is on in normal. If normally the yellow LED is ON, the door

is locked by output time schedule setting.

2. If it is case of “1”check OUTPUT T/S or reinitialize the device. If the problem remains after

performing it, please contact IDTECK service center.

3. If it is not the case of “1”, no communication, its yellow LED light off, it is of saved P/W deletion.

Please contact IDTECK service center.

4. Of V4.5 or higher, in case of “3” it shows message “CONTACT IDTECK”WWW.IDTECK.COM with

buzzer sound when the power is turn on.

20030516 User’s Manual

STAR

FINGER007

WARRANTY AND SERVICE

STAR FINGER007 warranty is 2 years from the shipping date; returns must have an RMA (Return Material Authorization) number. The customer is to provide a description of the specific problem. The customer is to include serial numbers, formats, and model numbers with the items to be returned.

Technical Support

OUTSIDE OF THE UNITED STATES

ID TECK Co., Ltd. Service Center 5F. Ace Techno Tower Bldg., 684-1 Deungchon-dong, Gangsuh-gu, SEOUL 157-030, KOREA Tel.: +82 (2) 2659-0055

Fax.: +82 (2) 2659-0086

E-mail: webmaster@idteck.com Web-site: www.idteck.com

IN THE UNITED STATES

RF Logics Inc. Service Center 3026 Scott Blvd., SANTA CLARA, CA95054 Tel.: (408) 980-0001 Fax.: (408) 980-8060 E-mail: rflogics@rflogics.com

Web-site: www.rflogics.com

CAUTION: Damage occurring during shipment is deemed the responsibility of the carrier, and

20030516 User’s Manual

claims should be made directly to the carrier.

STAR

FINGER007

TEMPLATE

20030516 User’s Manual

STAR

FINGER007

www.idteck.com

webmaster@idteck.com

Rev 2.0 ( 2003. 06. 19 )

20030516 User’s Manual

IDTECK Star Finger007, Star Finger007SR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual