Integrated Device Technology Inc IDT71L016L100PH, IDT71L016L100PHI, IDT71L016L70PH, IDT71L016L70PHI Datasheet
Integrated Device Technology, Inc.
LOW POWER 3V CMOS SRAM
1 MEG (64K x 16-BIT)
ADVANCE
INFORMATION
IDT71L016
FEATURES:
• 64K x 16 Organization
• Wide Operating Voltage Range: 2.7V to 3.6V
• Speed Grades: 70ns, 100ns
• Low Operating Power: 45mA (max)
• Low Standby Power: 5µA (max)
• Low-Voltage Data Retention: 1.5V (min)
• Available in a 44-pin TSOP package
FUNCTIONAL BLOCK DIAGRAM
OE
Output
Enable
Buffer
DESCRIPTION:
The IDT71L016 is a 1,048,576-bit very low-power Static
RAM organized as 64K x 16. It is fabricated using IDT’s highreliability CMOS technology. This state-of-the-art technology,
combined with innovative circuit design techniques, provides
a cost-effective solution for low-power memory needs. It uses
a 6-transistor memory cell.
All input and output signals of the IDT71L016 are LVTTLcompatible and operation is from a single extended-range
3.3V supply. This extended supply range makes the device
ideally suited for unregulated battery-powered applications.
Fully static asynchronous circuitry is used, requiring no clocks
or refresh for operation.
The IDT71L016 is packaged in a JEDEC standard 44-pin
TSOP Type II.
A0 - A15
CS
WE
BHE
BLE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
Address
Buffers
Chip
Enable
Buffer
Write
Enable
Buffer
Byte
Enable
Buffers
Row / Column
Decoders
64K x 16
Memory
Array
I/O 15
8
Sense
16
Amps
and
Write
Drivers
8
High
Byte
I/O
Buffer
Low
Byte
I/O
Buffer
8
I/O 8
I/O 7
8
I/O 0
3771 drw 01
INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES MAY 1997
1997 Integrated Device Technology, Inc. DSC-3771/2
1
IDT71L016
LOW POWER 3V CMOS STATIC RAM 1 MEG (64K x 16-BIT) COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
A4
A3
A2
A1
A0
CS
I/O 0
I/O 1
I/O 2
I/O 3
V
DD
V
I/O 4
I/O 5
I/O 6
I/O 7
WE
A15
A14
A13
A12
NC
1
2
3
4
5
6
7
8
9
10
11
SS
12
13
14
15
16
17
18
19
20
21
22
SO44-2
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
A5
A6
A7
OE
BHE
BLE
I/O 15
I/O 14
I/O 13
I/O 12
SS
V
V
DD
I/O 11
I/O 10
I/O 9
I/O 8
NC
A8
A9
A10
A11
NC
3771 drw 02
CAPACITANCE
(TA = +25°C, f = 1.0MHz)
Symbol Parameter
IN Input Capacitance VIN = 3dV 6 pF
C
I/O I/O Capacitance VOUT = 3dV 7 pF
C
NOTE: 3771 tbl 06
1. This parameter is guaranteed by device characterization, but not production tested.
(1)
Conditions Max. Unit
TSOP
TOP VIEW
PIN DESCRIPTIONS
A0 – A15 Address Inputs Input
CS
WE
OE
BHE
BLE
I/O
0 - I/O15 Data Input/Output I/O
V
DD Power Pwr
V
SS Ground Gnd
Chip Select Input
Write Enable Input
Output Enable Input
High Byte Enable Input
Low Byte Enable Input
3771 tbl 01
TRUTH TABLE
CS
CS
OE
OE
(1)
WE
WE
BLE
BLE
BHE
BHE
I/O0-I/O7 I/O8-I/O15 Function
H X X X X High-Z High-Z Deselected - Standby
L L H L H DATA
L L H H L High-Z DATA
L L H L L DATA
L X L L L DATA
L X L L H DATA
L X L H L High-Z DATA
OUT High-Z Low Byte Read
OUT High Byte Read
OUT DATAOUT Word Read
IN DATAIN Word Write
IN High-Z Low Byte Write
IN High Byte Write
L H H X X High-Z High-Z Outputs Disabled
L X X H H High-Z High-Z Outputs Disabled
NOTE: 3771 tbl 02
1.H = VIH, L = VIL, X = Don't care.
2
IDT71L016
LOW POWER 3V CMOS STATIC RAM 1 MEG (64K x 16-BIT) COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol Rating Com’l. and Ind'l. Unit
(2)
TERM
V
VTERM
Terminal Voltage with –0.5 to +4.6 V
Respect to V
(3)
Terminal Voltage with –0.5 to VDD+0.5V V
Respect to V
SS
SS
TBIAS Temperature Under Bias –55 to +125 °C
STG Storage Temperature –55 to +125 °C
T
T Power Dissipation 1.0 W
P
OUT DC Output Current 20 mA
I
NOTES: 3771 tbl 03
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
DD terminals only.
3. Input, Output,and I/O terminals; 4.6V maximum.
RECOMMENDED OPERATING
TEMPERATURE AND SUPPLY VOLTAGE
Grade Temperature VSS VDD
Commercial 0°C to +70°C 0V 2.7V to 3.6V
Industrial -40°C to +85°C 0V 2.7V to 3.6V
3771 tbl 04
RECOMMENDED DC OPERATING
CONDITIONS
Symbol Parameter Min. Typ. Max. Unit
VDD Supply Voltage 2.7 3.0 3.6 V
VSS Ground 0 0 0 V
VIH Input High Voltage 2.0 — VDD+0.3
V
IL Input Low Voltage –0.3
NOTE: 3771 tbl 05
1. VIH (max.) = VDD + 1.5V for pulse width less than 5ns, once per cycle.
2. V
IL (min.) = –1.5V for pulse width less than 5ns, once per cycle.
(2)
— 0.8 V
(1)
V
DC ELECTRICAL CHARACTERISTICS
VDD = 2.7V to 3.6V, Commercial and Industrial Temperature Ranges
Symbol Parameter Test Conditions Min. Max. Unit
LI| Input Leakage Current VDD = Max., VIN = VSS to VDD — 1 µA
|I
LO| Output Leakage Current VDD = Max.,
|I
OH Output High Voltage IOH = –1mA, VDD = Min. 2.4 — V
V
OL Output Low Voltage IOL = 2mA, VDD = Min. — 0.4 V
V
DC ELECTRICAL CHARACTERISTICS
VDD = 2.7 to 3.6V, VLC = 0.2V, VHC = VDD–0.2V, Commercial and Industrial Temperature Ranges
Symbol Parameter Test Conditions Typ.
I
CC2 Dynamic Operating Current
CC Static Operating Current
I
ISB1 Standby Supply Current
NOTES: 3771 tbl 08
1. All values are maximum guaranteed values.
2. Input low and high voltage levels are 0.2V and V
MAX = 1/tRC (all address inputs are cycling at fMAX).
3. f
4. f = 0 means no address input lines are changing
5. Typical conditions are V
DD = 3.0V and specified temperature.
CS
= VLC, Outputs Open, -70 ns — 45 mA
V
DD = 3.6V, f = fMAX
CS
= VLC, Outputs Open, — 10 mA
WE
= V
HC, VDD = 3.6V, f = 0
CS
= VHC, Outputs Open, -40 to 85°C— 10µA
DD = 3.6V 0 to 70°C— 5
V
DD-0.2V respectively for all tests.
.
(1, 2)
CS
= VIH, VOUT = VSS to VDD — 1 µA
(5)
(3)
(4)
-100 ns — 35
Max. Unit
40°C—2
25°C—1
3771 tbl 07
3
Loading...