IDT IDT23S05E User Manual

查询IDT23S05E供应商

IDT23S05E

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE

FEA TURES:

• Phase-Lock Loop Clock Distribution

• 10MHz to 200MHz operating frequency

• Distributes one clock input to one bank of five outputs

• Zero Input-Output Delay

• Output Skew < 250ps

• Low jitter <200 ps cycle-to-cycle

• IDT23S05E-1 for Standard Drive

• IDT23S05E-1H for High Drive

• No external RC network required

• Operates at 3.3V VDD

• Power down mode

• Spread spectrum compatible

• Available in SOIC package

IDT23S05E

DESCRIPTION:

The IDT23S05E is a high-speed phase-lock loop (PLL) clock buffer, designed to address high-speed clock distribution applications. The zero delay is achieved by aligning the phase between the incoming clock and the output clock, operable within the range of 10 to 200MHz.

The IDT23S05E is an 8-pin version of the IDT23S09E. IDT23S05E accepts one reference input, and drives out five low skew clocks. The -1H version of this device operates up to 200MHz frequency and has a higher drive than the -1 device. All parts have on-chip PLLs which lock to an input clock on the REF pin. The PLL feedback is on-chip and is obtained from the CLKOUT pad. In the absence of an input clock, the IDT23S05E enters

power down. In this mode, the device will draw less than 12µA for Commercial Temperature range and less than 25µA for Industrial temperature range, the outputs are tri-stated, and the PLL is not running, resulting

in a significant reduction of power.

The IDT23S05E is characterized for both Industrial and Commercial operation.

FUNCTIONAL BLOCK DIAGRAM

PLL

REF

Control

Logic

CLKOUT

CLK1

CLK2

CLK3

CLK4

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

2003 Integrated Device Technology, Inc. DSC - 6398/5c

OCTOBER 2003

IDT23S05E

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

PIN CONFIGURATION

REF CLK2 CLK1

GND

2 3 4

SOIC

TOP VIEW

ABSOLUTE MAXIMUM RATINGS

Symbol Rating Max. Unit

VDD Supply Voltage Range –0.5 to +4.6 V

(2)

7 6 5

CLKOUT CLK4 V

CLK3

VI V

I Input Voltage Range –0.5 to V

IIK (VI < 0) Input Clamp Current –5 0 mA IO (VO = 0 to VDD) Continuous Output Current ±50 mA VDD or GND Continuous Current ±100 mA T

A = 55°C Maximum Power Dissipation 0.7 W

(in still air) TSTG Storage Temperature Range –65 to +150 °C Operating Commercial Temperature 0 to +70 °C Temperature Range Operating Industrial Temperature -40 to +85 °C Temperature Range

NOTES:

1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause

2. The input and output negative-voltage ratings may be exceeded if the input and output

3. The maximum package power dissipation is calculated using a junction temperature

(3)

permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

clamp-current ratings are observed. of 150°C and a board trace length of 750 mils.

Input Voltage Range (REF) –0.5 to +5.5 V

(except REF) VDD+0.5

(1)

APPLICA TIONS:

• SDRAM

• Telecom

• Datacom

• PC Motherboards/Workstations

• Critical Path Delay Designs

PIN DESCRIPTION

Pin Name Pin Number Type Functional Description

(1)

REF

(2)

CLK2

(2)

CLK1 GND 4 Ground Ground

(2)

CLK3 VDD 6 PWR 3.3V Supply

(2)

CLK4 CLKOUT

NOTES:

1. Weak pull down.

2. Weak pull down on all outputs.

(2)

1 IN Input reference clock, 5 Volt tolerant input 2 Ou t Output clock 3 Ou t Output clock

5 Ou t Output clock

7 Ou t Output clock 8 Ou t Output clock, internal feedback on this pin

IDT23S05E

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

OPERATING CONDITIONS - COMMERCIAL

Symbol Parameter Min. Max. Unit

VDD Supply Voltage 3 3.6 V

TA Operating Temperature (Ambient Temperature) 0 7 0 °C

CL Load Capacitance < 100MHz — 30 pF

Load Capacitance 100MHz - 200MHz — 10

IN Input Capacitance — 7 pF

DC ELECTRICAL CHARACTERISTICS - COMMERCIAL

Symbol Parameter Conditions Min. Max. Unit

VIL Input LOW Voltage Level — 0.8 V VIH Input HIGH Voltage Level 2 — V

IIL Input LOW Current VIN = 0V — 50 µA IIH Input HIGH Current VIN = VDD — 100 µA

VOL Output LOW Voltage Standard Drive IOL = 8mA — 0.4 V

High Drive IOL = 12mA (-1H)

VOH Output HIGH Voltage Standard Drive IOH = -8mA 2.4 — V

High Drive IOH = -12mA (-1H)

IDD_PD Power Down Current REF = 0MHz — 12 µA

IDD Supply Current Unloaded Outputs at 66.66MHz — 32 mA

SWITCHING CHARACTERISTICS (23S05E-1) - COMMERCIAL

(1,2)

Symbol Parameter Conditions Min. Typ. Max. Unit

1 Output Frequency 10pF Load 1 0 — 20 0 MHz

30pF Load 1 0 — 10 0

Duty Cycle = t2 ÷ t1 Measured at 1.4V, FOUT = 66.66MHz 4 0 50 60 % t3 Rise Time Measured between 0.8V and 2V — — 2.5 ns t4 Fall Time Measured between 0.8V and 2V — — 2.5 ns t5 Output to Output Skew All outputs equally loaded — — 250 ps t6 Delay, REF Rising Edge to CLKOUT Rising Edge Measured at VDD/2 — 0 ±350 ps t7 Device-to-Device Skew Measured at VDD/2 on the CLKOUT pins of devices — 0 70 0 ps tJ Cycle-to-Cycle Jitter, pk - pk Measured at 66.66MHz, loaded outputs — — 200 ps

LOCK PLL Lock Time Stable power supply, valid clock presented on REF pin — — 1 ms

NOTES:

1. REF Input has a threshold voltage of VDD/2.

2. All parameters specified with loaded outputs.

+ 5 hidden pages