I.D. Systems UTP 1.0 Installation & Verification Instructions
UTP 1.0
INSTALLATION &
VERIFICATION INSTRUCTIONS
©2017 I.D. Systems, Inc.
055-00000889 Rev B
UTP 1.0 Installation & Verification Instructions
I.D. Systems Confidential and Proprietary
1
055-00000889 Rev A
Copyright © 2017 I.D. Systems, Incorporated. All Rights Reserved.
The material contained in this document is protected by the copyright and trade secret laws of
the United States and other countries. It may not be reproduced, distributed, or altered in any
fashion by any entity (either internal or external to I.D. Systems, except in accordance with
applicable agreements, contracts, or licensing, without the express written consent of the Brand
or Marketing Communications Director or the business management owner of the material.
Disclaimer and Limitations of Liability
The information contained in this Guide is subject to change without notice and should not be
construed as a specification.
NOTICE: This device complies with Part 15 of the FCC Rules and with Industry Canada
license-exempt RSS standard(s)].
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
NOTICE: Changes or modifications made to this equipment not expressly approved by
I.D. Systems may void the FCC authorization to operate this equipment.
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
UTP 1.0 Installation & Verification Instructions
I.D. Systems Confidential and Proprietary
2
055-00000889 Rev A
I.D. Systems
www.id-systems.com/
Customer Support: 888-855-0913
UTP 1.0 Installation & Verification Instructions
I.D. Systems Confidential and Proprietary
3
055-00000889 Rev A
Table of Contents
1. OVERVIEW .............................................................................................................................................. 4
2. UTP 1.0 COMPONENTS ............................................................................................................................ 4
3. REQUIRED TOOLS (NOT PROVIDED) .......................................................................................................... 4
4. INSTALLATION STEPS ............................................................................................................................... 5
5. LED INDICATORS ................................................................................................................................... 11
6. INSTALLING ON MULTIPLE VEHICLES AT THE SAME TIME ......................................................................... 12
7. UNINSTALLING THE UTP 1.0 ................................................................................................................... 13
UTP 1.0 Installation & Verification Instructions
I.D. Systems Confidential and Proprietary
4
055-00000889 Rev A
1. Overview
• This document details UTP 1.0 (remote vehicle monitoring and control hardware) installation
and verification process.
• Failure to follow the installation and verification processes may result in improper device
operation and/or payment dispute for installation services.
• Contact Avis Budget Group customer support at xxxxxxxxxx with any questions regarding
installation and/or verification.
• This document can be download in electronic format from http://ww2.id-
systems.com/support/training/VMS_Guides/UTP1.0_installation_Rev1.pdf.
• Any recommendations and/or corrections should be forwarded to dflanagin@idsystems.com.
2. UTP 1.0 Components
• UTP 1.0 Enclosure
• Cable
• OBD-II Connector
• LED area
3. Required Tools (Not Provided)
• Five 8” tie wraps
• 4.5” wire cutter
Enclosure
Cable
OBD
-
II Connector
LED area
Loading...