IDS 816 Installer Manual

Download

Page 1

Page 2

IDS 816 700-283-02I Issued September 2009

Page 3

IDS 816 700-283-02I Issued September 2009

Contents

1. Introduction to the IDS 816 ----------------------------------------------------------------------------- 8

1.1 Features of the IDS 816 --------------------------------------------------------------------------------------8

2. Installation and Wiring ----------------------------------------------------------------------------------- 9

2.1 Additional Technical Data --------------------------------------------------------------------------------- 10

2.2 End-of-Line Resistors--------------------------------------------------------------------------------------- 10

2.3 Box Tamper Input ------------------------------------------------------------------------------------------- 12

2.4 Installing an Expander Module --------------------------------------------------------------------------- 12

2.5 Connecting the Telephone Communicator ------------------------------------------------------------ 12

2.6 Programmable Outputs ------------------------------------------------------------------------------------ 12

2.7 Key-switch or Remote Control Unit ---------------------------------------------------------------------- 12

2.8 IDS Remote Receiver --------------------------------------------------------------------------------------- 13

2.9 Radio Transmitter Connection ---------------------------------------------------------------------------- 13

3. Hardware Reset Switch --------------------------------------------------------------------------------- 13

4. Enrolling Keypads and Other Devices ------------------------------------------------------------- 13

4.1 Replacing a Faulty Keypad/Device ---------------------------------------------------------------------- 14

4.2 Defaulting Keypads ----------------------------------------------------------------------------------------- 14

5. Event Log --------------------------------------------------------------------------------------- 15

6. Download Code --------------------------------------------------------------------------------------- 15

6.1 Programming the Panel ------------------------------------------------------------------------------------ 15

6.2 Location Values ---------------------------------------------------------------------------------------------- 15

7. Programming the Panel --------------------------------------------------------------------------------- 16

7.1 Entering Program Mode ----------------------------------------------------------------------------------- 17

7.2 Programming Standard Locations ---------------------------------------------------------------------- 17

7.3 Programming Extended Locations ---------------------------------------------------------------------- 17

7.4 Programming a Bitmapped Location ------------------------------------------------------------------- 18

7.5 Incorrect Data Entries -------------------------------------------------------------------------------------- 18

7.6 Programming Location Summary ----------------------------------------------------------------------- 18

7.6.1 Zone Options ------------------------------------------------------------------------------------------------- 19

7.6.2 System Options ---------------------------------------------------------------------------------------------- 23

8. System Reporting Codes (4 x 2 and Domestic) ------------------------------------------------ 28

9. System Programmable Outputs ---------------------------------------------------------------------- 30

10. System Clock Options ----------------------------------------------------------------------------------- 32

11. Communicator Options --------------------------------------------------------------------------------- 34

11.1 Programming Telephone Numbers --------------------------------------------------------------------- 40

11.2 Telephone Number Storage Locations ----------------------------------------------------------------- 41

11.3 Download Options ------------------------------------------------------------------------------------------ 41

12. Partition Setup --------------------------------------------------------------------------------------- 42

13. User Options --------------------------------------------------------------------------------------- 48

Page 4

IDS 816 700-283-02I Issued September 2009

14. Programmable Output Options----------------------------------------------------------------------- 49

15. Keypad Options --------------------------------------------------------------------------------------- 51

16. Installer Options --------------------------------------------------------------------------------------- 52

Index of Programming Locations ------------------------------------------------------------------------------ 53

Index --------------------------------------------------------------------------------------- 56

Page 5

IDS 816 700-283-02I Issued September 2009

Figures

Figure 1 : Connection Diagram without Tamper per Zone -------------------------------------------- 9

Figure 2 : Tamper by Zone Connection --------------------------------------------------------------------- 10

Figure 3 : Zone Doubling Connection ----------------------------------------------------------------------- 11

Figure 4 : Resistors (Tamper per Zone or Zone Doubling) ------------------------------------------ 11

Figure 5 : Programmable Output Configuration --------------------------------------------------------- 12

Figure 6 : Fire Detect Output Sequence -------------------------------------------------------------------- 32

Tables

Table 1 : Values Represented by Each Zone LED ------------------------------------------------------- 16

Table 2 : Hexadecimal Value ----------------------------------------------------------------------------------- 17

Table 3 : Location / Zone Defaults ---------------------------------------------------------------------------- 19

Table 4 : Programmable Zone Types ------------------------------------------------------------------------ 20

Table 5 : Programmable Output Numbering -------------------------------------------------------------- 30

Table 6 : Output Actions--------------------------------------------------------------------------- --------- ----30

Table 7 : Event Driven Programmable Outputs ---------------------------------------------------------- 31

Table 8 : Function Driven Programmable Outputs ------------------------------------------------------ 31

Table 9 : Value for Day of the Week -------------------------------------------------------------------------- 33

Table 10 : Standard Contact ID Reporting Codes ------------------------------------------------------- 37

Table 11 : User Code Locations -------------------------------------------------------------------------------- 48

Page 6

IDS 816 700-283-02I Issued September 2009

Page 7

IDS 816 700-283-02I Issued September 2009

Page 8

IDS 816 700-283-02I Issued September 2009

1. Introduction to the IDS 816

The IDS 816 is a versatile, microprocessor based eight zone Alarm Panel. It has two partitions and can be expanded to sixteen zones. Most features are optional and may be programmed either directly through the keypads or via the telephone system, using the IDS download software and appropriate modem.

There are eight programmable burglary zones, a dedicated panic zone, monitored siren output, auxiliary power outputs and five programmable outputs, which may be programmed to perform various, trigger/switching functions.

For correct operation, the IDS 816 must be used in conjunction with the specified transformer/battery combination and appropriate peripheral sensors and signalling devices.

1.1 Features of the IDS 816

 Eight programmable, end-of-line supervised zone inputs  Expandable to sixteen zones via keypad zones, zone expander module, zone doubling or

wireless expansion.

 2 partitions  Optional tamper reporting per zone using double end-of-line resistors (12K and 4K7)  Fully programmable digital telephone communicator that supports most industry standard

formats.

 Five programmable outputs on alarm panel. Expandable to seven when using Wired Zone

Expander module.

 Non volatile EEPROM memory retains all program and event log data in the event of a total power

failure

 Programmable loop response time  Up and downloadable using IDS Windows based software, either directly via RS 232 or remotely

using a modem.

 Excellent protection against lightning (provided by specialised “zap tracking” and transient

suppressors)

 Auto arm/disarm capability per partition and by day of the week. The panel can be programmed

to arm/disarm at a pre-determined time

 Fax defeat/answering machine override  Dual reporting provides for duplicated reporting to two independent central base stations.  Dynamic battery self test  Low battery cut out circuit

Page 9

IDS 816 700-283-02I Issued September 2009

2. Installation and Wiring

Please refer to Figure 1: Connection Diagram and familiarise yourself with the following sections.

Figure 1 : Connection Diagram without Tamper per Zone

Page 10

IDS 816 700-283-02I Issued September 2009

2.1 Additional Technical Data

 A suitable transformer with an output voltage of 16 volts AC ±10% with a 16VA minimum rating

must be used. A 32 VA transformer is recommended for larger installations.

 A 12V sealed lead acid battery with a minimum capacity of 7AH must be used. The back up

period after mains failure will depend on the number of keypads, sensors and peripheral devices connected to the system.

 The panel can supply a total continuous current of 750mA to peripheral devices such as keypads,

remotes, receivers, passives etc.

 Connect a 12-volt self-driven siren or piezo siren [not a horn speaker] to the siren output.

2.2 End-of-Line Resistors

(Including Tamper by Zone / Zone Doubling)

 All zones must be end-of-line supervised.  Any unused zones must be terminated with a 3K3 resistor. The end of line resistor must be

placed inside or as close to the sensor as possible.

 If neither zone doubling nor tamper by zone are required the 3K3 resistor must be used.  For zone doubling or tamper per zone, the 4K7 and 12K end-of-line resistors must be connected

as per Figures 2 and 3.

Figure 2 : Tamper by Zone Connection

Tamper operation is as follows:

 If the panel is unarmed and a tamper condition occurs, the siren will not sound but a tamper

condition will be reported.

 If the panel is armed and a tamper condition occurs an audible alarm will register and a tamper

condition AND zone violation will be reported.

 Panic zones always register panic and tamper conditions.  The colour codes for the 12K and 4K7 resistors are as per in Figure 4.

Page 11

IDS 816 700-283-02I Issued September 2009

Figure 3 : Zone Doubling Connection

The following limitations apply to zone doubling:

1. Only normally closed contacts (n/c) may be used.

2. If the zone input to the panel is short or open circuited at the panel, both the zone and its double

will be violated.

3. If the 12K resistor is “open circuited” the primary zone will indicate a violation i.e. assuming zone

8 is doubled in this case zone 8 will be indicated as violated.

4. If the 4K7 resistor is “open circuited” the secondary zone will indicate a violation i.e. assuming the

example in 3 above zone 16 would indicate the violation.

5. The colour codes for the 4K7 and 12K resistors are shown in Figure 4.

Figure 4 : Resistors (Tamper per Zone or Zone Doubling)

Page 12

IDS 816 700-283-02I Issued September 2009

2.3 Box Tamper Input

The box tamper input does not require an end-of-line resistor and requires a normally closed contact.

2.4 Installing an Expander Module

When installing an expander module refer to the document supplied with the module. Note that only one (8-zone) expansion module may be added to the IDS 816 Alarm Panels.

2.5 Connecting the Telephone Communicator

Refer to Figure 1. Connection Diagram (Page 9).

For optimum lightning protection, connect a low impedance earth to the communicator earth input. Always connect the telephone communicator in line seizure mode and never in parallel with the telephone. Ensure the telephone receiver is connected to the communicator terminals marked “phone” and the incoming line to the terminals marked “line”.

2.6 Programmable Outputs

A relay board must be used when any device requiring a high current is connected to a programmable

output. The programmable output circuitry consists of a 12-volt source with a 56

Ω series resistor.

Current sink is via a 1 000

Ω resistor to negative. For information purposes, the output circuitry for a

single output is shown in Figure 5.

Figure 5 : Programmable Output Configuration

2.7 Key-switch or Remote Control Unit

A momentary key-switch or non-latching remote control receiver may be connected to any zone to allow remote arm/disarm and remote panic capability.

 When using a key-switch or remote control unit a 3K3 resistor must be connected between the

zone input and ground.

Page 13

IDS 816 700-283-02I Issued September 2009

 Use only a spring-loaded momentary key-switch or non-latching remote control unit.

2.8 IDS Remote Receiver

An IDS Remote Receiver (P/N 860-07-002DI) may be connected to the keypad bus. Using this facility allows remote arming and disarming of the panel while providing user identification for a maximum of 32 remotes.

2.9 Radio Transmitter Connection

When connecting a radio transmitter, use the TX terminal provided on the PCB to supply power to the transmitter. (Figure 1) The 4 Amp battery fuse protects this output.

3. Hardware Reset Switch

Should the need arise to return the panel to factory default, use the hardware reset switch (Figure 1).

The panel may be defaulted as follows:

Remove both battery and AC power from the panel. While depressing the reset switch reapply power to the panel by either connecting the battery or the AC power. Release the reset switch approximately 2 seconds after reapplying the power. Factory default values will now be restored to all locations and all attached keypad IDs will be defaulted. A default event will be logged and the existing event log will NOT be erased.

NOTE:

If reset switch has been disabled by programming a 10 into location 444, it will no longer be possible to default the panel using the reset switch. The panel can only be defaulted if a valid installer code is entered and a value of [0] is entered into location 0.

4. Enrolling Keypads and Other Devices

A new panel supplied from the factory will have factory default values in all locations (as indicated throughout this manual). Similarly new keypads will have no ID assigned to them. It is however good practice to default the system by using the reset switch prior to commencement of programming. This will ensure that the above is true and that no factory test values remain.

The keypad(s) attached to a system as defaulted above will have no ID and will therefore not

communicate with the panel. This is indicated by all keypad LED’s flashing simultaneously.

In order to enrol a keypad (thereby giving the keypad an ID) press the [#] key of the keypad

you wish to enrol. The enrolled keypad will now indicate the alarm status. Repeat this process with the remaining keypads where more than 1 keypad is used. The first keypad enrolled will have an ID of 1, the second enrolled will have an ID of 2, the third an ID of 3 etc. A maximum of 8 keypads may be used. (The [P] and [M] keys can be used to scroll up and down trough the menu functions).

NOTE:

If the keypad zone is to be used, consideration must be given to the sequence in which keypads are enrolled as this affects the LED zone designation. The keypad 1 will contain zone 16, keypad 2 will contain zone 15 etc. as per section 14 in this manual.

Page 14

IDS 816 700-283-02I Issued September 2009

To enrol other devices (IDS Remote Receivers or Zone Expanders); consult the installation instructions for those devices. The IDS 816 Alarm Panels can only accept one zone expander and/or one IDS Remote Receiver.

4.1 Replacing a Faulty Keypad/Device

NOTE: Should a faulty keypad be REPLACED with another keypad, the following applies:

1. Disconnect ONLY the faulty keypad.

2. Program a value 4 into location zero to free up all vacant addresses.

3. Connect the replacement keypad and enrol it - by pressing [#] – it will now be enrolled in the first

available address, which should now be the address just freed up in step 2.

NOTE:

If other devices (keypads) are disconnected (or faulty), at the time of performing step 2, their addresses will also be freed. Any new devices being enrolled will automatically be allocated addresses beginning from the lowest free address. This can cause devices to be associated with the wrong addresses/partitions. The resultant communications attempts made to the wrong addresses can result in sluggish system behaviour. Operation will become confusing.

Check

After enrolling a keypad, go to location 446 to check the keypad’s ID (which is a number that corresponds to the order that the keypads were enrolled). If the keypad ID is incorrect (2

keypad has ID

= 3, for example), then this must be rectified for the system is to operate correctly.

Solution

If the system is complex and has developed a keypad allocation problem, it is recommended that all keypads are defaulted and registered “from scratch”, as it were, in the correct, required sequence.

To re-enrol a zone expander, or an IDS Remote Receiver, consult the installation instructions for the relevant device.

4.2 Defaulting Keypads

To default the ID of an individual keypad:

Power off, Hold [1] & [3], Restore power, Release [1] & [3]

1. Remove power to the keypad (or the whole panel if easier). Whilst holding down the [1] and [3]

keys restore the power to the keypad.

2. All the keypad LED’s will flash simultaneously indicating that the keypad has now been de-

registered.

3. The ID of any (correctly registered) keypad can be interrogated by viewing the data in location

446 from the keypad of interest.

4. Wait for five seconds and then press the hash [#] key to allocate a new ID to the defaulted

keypad. Keypad IDs are allocated incrementally.

To default the ID of ALL keypads:

Programming a value of [3] into location [0] causes ALL keypads to be defaulted.

Page 15

IDS 816 700-283-02I Issued September 2009

[INSTALLER CODE] [*] [0] [*] [3] [*]

On pressing the final [*], wait a few seconds and ALL the keypads will begin flashing. (Do NOT press [#] at the end of this sequence, unless you wish the keypad you are using to be registered in the first address)

Re-enrol all keypads by pressing [#] on each keypad – in the CORRECT sequence to ensure that keypad zone and partition allocation is as required by the user.

5. Event Log

A comprehensive log of the 500 most recent events is retained in the non-volatile EEPROM. The log may be retrieved using the up/ download software. Alternatively, it can be viewed using an LCD keypad. (See LCD Keypad Manual)

6. Download Code

The download code (in conjunction with the installer code) is required for download access. The default download code is 9999. Using the downloading software, it is possible to program a location that will either allow or disallow defaulting of the download code.

This location is only accessible using the download software. If the panel is defaulted, the download code will revert back to 9999. A value of [1] [0] programmed into this location will prevent the download code from being defaulted when defaulting the panel.

6.1 Programming the Panel

The panel can be programmed either via a keypad or via the up/ download software. Programming the panel by means of an LED keypad is explained below:

NOTE: Before commencing programming, it is advisable to read the Installer Manual thoroughly.

6.2 Location Values

All values within a program location will be displayed by the zone indicators in binary coded decimal format i.e. zone indicators 1-4 indicate units (1’s) and zone indicator 5-8 indicate tens (10’s), and so on.

To read a binary value on the keypad sum the values represented by each LED that is on, as shown in Table 1.

Page 16

IDS 816 700-283-02I Issued September 2009

Table 1 : Values Represented by Each Zone LED

Zone LED

Value

Digit

Zone LED

Value

Digit

Zone 1 1

Units

Zone 9 1

Hundreds

Zone 2 2 Zone 10 2 Zone 3 4 Zone 11 4

Zone 4

Zone 12

Zone 5

Tens

Zone 13

Thousands

Zone 6

Zone 14

Zone 7 4 Zone 15 4 Zone 8 8 Zone 16 8

Example:

Assume the following zone indicators are on:

Zone 1, Zone 3 and Zone 5.

Units are represented by the sum of Zone 1 and Zone 3 (i.e. 1 + 4) and tens of units are represented by the value of Zone 5 (i.e. 1)

Thus, the value indicated by the LED’s that are on will be shown below.

Zone LED

Value

Digit

Zone 1 1

Units

Zone 2

Zone 3

Zone 4

Zone 5 1

Tens

Zone 6 2 Zone 7 4 Zone 8 8

Therefore, the displayed value is 15.

7. Programming the Panel

For all programming procedures, the [*] star key functions as the <ENTER> key and the [#] hash key functions as a <CLEAR> or an <EXIT> program key.

Invalid data entries are indicated by means of an error beep consisting of 3 short beeps of the keypad buzzer.

There are two location categories:

 Standard locations which are single tiered and do not contain any sub-locations.  Extended locations, which are double tiered and have sub-locations.

Both standard and extended locations may contain further subcategories referred to as bitmapped locations. For both main categories, clear visual keypad prompts are provided which aid the programming process.

Page 17

IDS 816 700-283-02I Issued September 2009

To read the data stored in multi-digit locations (e.g. a telephone number, account codes, etc.), enter the location. Upon initial entry into the location, the zone indicators will display the first digit. Pressing the [Panic] key will cause the next digit within the location to be displayed.

Where a hexadecimal number must be programmed, use the [MODE] key as per Table 2 below:

Table 2 : Hexadecimal Value

Hex Value

Decimal Value

Key Strokes

A 10 [MODE] key then [0] key B 11 [MODE] key then [1] key C 12 [MODE] key then [2] key D 13 [MODE] key then [3] key E 14 [MODE] key then [4] key F 15 [MODE] key then [5] key

7.1 Entering Program Mode

1. Ensure that all partitions are unarmed.

2. Press the [#] hash key followed by the [INSTALLER CODE].

3. The default installer code is 9999 or alternatively 999999 should a six digit default installer code

have been used.

4. Press the [*] star key and a long beep will confirm entry into program mode. If a correct code

has been entered, the green READY indicator will flash.

7.2 Programming Standard Locations

1. Ensure the panel is in program mode - the READY indicator will be flashing.

2. Enter the [LOCATION NUMBER] of the program location you wish to view or change.

3. Press the [*] star key. The READY indicator will continue flashing and the AWAY indicator will

come on.

4. The zone LED’s will display the data stored in the program location in binary format.

5. Enter the [NEW DATA] followed by the [*] star key. A long beep will indicate a valid entry and the

AWAY indicator will turn off.

6. If you do not wish to change the data, press the [#] key. The READY indicator will continue

flashing and the AWAY indicator will turn off.

7. Repeat steps 2 - 6 until all the necessary locations have been programmed.

8. Press the [#] hash key to exit program mode.

9. The READY indicator will stop flashing and the panel will return to the standby mode.

7.3 Programming Extended Locations

1. Ensure that the panel is in program mode - the READY indicator will be flashing.

2. Enter the [LOCATION NUMBER] of the program location that you wish to view or change.

3. Press the [*] star key. The READY indicator will continue flashing and the ARMED indicator will

come on.

4. Enter the [SUB-LOCATION NUMBER] for the program location that you wish to view or change.

5. Press the [*] star key, a long beep indicates a valid data entry. The READY indicator will continue

flashing and the ARMED and AWAY indicators will come on.

6. Enter the [NEW DATA] followed by the [*] star key. A long beep will indicate a valid entry. The

AWAY indicator will turn off.

Page 18

IDS 816 700-283-02I Issued September 2009

7. If you do not wish to change the data within this sub-location, press the [#] hash key. The

READY indicator will continue flashing and the AWAY indicator will turn off.

8. Repeat steps 4 to 7 until all sub-locations at the current location have been programmed as

required.

9. Press the hash [#] key to exit from the current location, the ARMED LED will turn off and the

READY indicator will continue flashing.

10. Repeat steps 2 to 9 until all locations, and their sub-locations, have been programmed as

required.

11. Press the [#] hash key again to exit from program mode (READY LED will stop flashing).

7.4 Programming a Bitmapped Location

1. A bitmapped location allows the installer to program multiple panel features within a single

location or sub-location. This is achieved using the individual zone LED’s to indicate which features are enabled or disabled.

2. By referring to the appropriate location reference tables, the installer can view the entire selection

of features associated with that location.

3. A zone LED that is on indicates that a feature is enabled. A LED that is off indicates that a feature

is disabled.

4. The installer is able to toggle a selected LED indicator ON or OFF by entering the corresponding

number followed by the [*] star key

5. Once a complete selection of features has been finalised, press the [#] key to leave the

location/sub-location with the state as indicated by the LED.

Example:

Location 40 allows the installer to select up to twelve trouble conditions which may be displayed. By default, only AC fail and low battery trouble conditions are enabled.

Entering program mode and viewing the contents of Location 40 it will be noted that the zone 1 and zone 5 LED’s will be on. All other zone LED indicators will be turn off.

To enable the Comms Fail Trouble Display (indicated by zone 2 LED) press the [2] key followed by the [*] star key. A long beep will indicate a valid entry and the zone 2 LED will come on indicating that Comms Fail Trouble Display has been enabled.

Continue selection (or de-selection) of the desired trouble conditions. Once a final selection has been made press the [#] hash key to exit the location. The AWAY indicator will turn off and a long beep will indicate acceptance of a valid data entry.

7.5 Incorrect Data Entries

1. When programming either standard or extended locations any attempt to enter invalid data will

result in an error beep (3 short beeps)

2. In the case of standard locations, the AWAY indicator will remain on after the error beeps. Re-

enter the correct data. There is no need to press the [#] hash key.

3. In the case of extended locations, the AWAY and ARMED indicators will remain on after the error

beeps. Re-enter the correct data. There is no need to press the [#] key.

7.6 Programming Location Summary

A detailed description of each location and its options follows.

Page 19

IDS 816 700-283-02I Issued September 2009

LOCATION 0 Defaulting of the Panel or Master User Code

Value

Action

Will reset all locations to the factory default values. (Master User Code 1234) and all keypad IDs will be defaulted.

Will default the master user code to 1234

- or 123456 if 6 digits are being used.

Master user code properties will also be defaulted. 2 Defaults ALL users 3 Defaults ALL keypads

Remove Missing Devices

A missing device (keypads, for example), will have its address freed up, making

its address available for a new device when it is enrolled. This MUST be done

when replacing a faulty device – see “Enrolling Keypads and other Devices”,

page 13.

7.6.1 Zone Options

LOCATIONS 1 - 16 Individual Zone Setup

Sub-location 1 Zone type

The first sub-locations of program locations 1 - 16 are used to define the zone characteristics of each of the sixteen zones. There are 13 zone types. Table 3 provides a location/zone cross-reference together with the default zone characteristics.

Table 3 : Location / Zone Defaults

Zone

Location

Sub-location 1 Default

Zone Type

1 1 1 Entry / Exit 2 2 2 Follower

Audible Instant

4 4 4 Audible Instant 5 5 4 Audible Instant 6 6 4 Audible Instant 7 7 4 Audible Instant 8 8 4 Audible Instant

9 9 0 Disabled 10 10 0 Disabled 11 11 0 Disabled 12 12 0 Disabled 13 13 0 Disabled

14 0 Disabled

15 15 0 Disabled 16 16 0 Disabled

Table 4 provides a complete list of the different zone types together with a description of their characteristics.

Page 20

IDS 816 700-283-02I Issued September 2009

Table 4 : Programmable Zone Types

Value

Zone Type

DISABLED

A Zone violation of a disabled zone is ignored by the control panel and will not be indicated on the keypad.

PRIMARY ENTRY / EXIT ZONE

Violations of an Entry/Exit zone are ignored during the exit delay period of the arming procedure. Violating an Entry/Exit zone when armed will initiate the entry delay. If valid User

Code is not entered before the entry delay period expires, an alarm condition will be registered. Failure to exit through an Entry/Exit zone after arming will cause the panel to Stay Arm. This zone may also function as an Entry/Exit zone that is COMMON to two partitions. In such a case, should a user violate this zone and then disarm his partition, the OTHER partition will rearm after the entry delay.

SECONDARY ENTRY / EXIT ZONE

The secondary entry delay will be activated if this zone is violated when the panel is armed.

FOLLOWER ZONE

A violation of a Follower zone is ignored during the entry/exit delay period (this allows the user to enter/exit via the Follower zone). A Follower zone will behave as an instant zone if the panel is armed and an Entry/Exit zone is not violated prior to violation of the follower zone.

PANIC / PRIORITY ZONE

Regardless of whether the panel is armed or not, a violation of a Priority zone will cause the

control panel to register a panic condition. This zone type CANNOT be bypassed.

INSTANT ZONE

When the panel is armed the violation of an instant zone will cause the control panel to register an alarm condition.

ARM/DISARM ZONE

The violation of an Arm/Disarm zone will cause the panel to toggle between (away) armed and disarmed. It is typical to connect a momentary key-switch, or non-latching remote control unit to this zone.

9 RESERVED

FIRE ZONE

Violation of a Fire zone will cause the siren to sound regardless of whether the panel is armed or not. The siren will sound intermittently (one second on, one second off) For correct operation a programmable output programmed as a fire detector power output must be used to control power to the fire detector. There is a 10 second violation when unarmed and instant when armed.

TAMPER ZONE

Violation of this zone will be reported to the base station regardless of whether the panel is armed or disarmed. If the panel is armed, the siren will be activated.

24 HOUR ALARM ZONE

This works the same as a panic zone – with the exception that it can be bypassed.

WARNING ZONE

When the panel is armed, violation of a warning zone will cause the siren to beep. The violation is logged in the event log but it is not reported to the base station. Warning zones may be included and will be counted when used as part of the cross-zone matrix.

PUSH TO ARM ZONE

Violation of a push to arm zone during the exit delay will immediately arm the panel.

OUTDOOR INSTANT ZONE

When the panel is armed violation of an outdoor instant zone will cause the panel to register an alarm condition.

Page 21

IDS 816 700-283-02I Issued September 2009

Sub-location 2 Zone Properties

NOTE: Select all the options for each zone. Shaded areas in the table indicate default values. This is a bitmapped location.

LED

ON / OFF

Zone Properties

ON Tamper by zone enabled

OFF Tamper by zone disabled

ON Cross-zone enabled

OFF Cross-zone disabled

ON Shutdown zone enabled

OFF Shutdown zone disabled

ON Silent zone enabled

OFF Silent zone disabled

Default values are shaded

Further zone related functionality explained

Tamper by Zone

Individual zones may be enabled for tamper by zone. For connection details, see Figure 2. This feature is not available if zone doubling is enabled. (Figure 3, page 11 and location 38, page 24)

Cross-zoning

This feature is useful for reducing false alarms. Violating zones with the cross-zone property enabled will not immediately generate an alarm. The cross-zone delay timer is started. (location 36).

Depending on the value programmed into location 37 (Cross-zone Trip Count), the zone (or any other zone with cross-zone option enabled) must trip the number of times programmed into location 37 before an alarm is generated. An alarm will also be generated should any single zone remain violated for the entire delay period (location 36). An entry/exit cannot be cross-zoned.

Swinger Shutdown

During a single arm cycle, if the number of alarm violations generated by a swinger zone equals the shutdown count (location 33), the control panel will automatically bypass the zone. The swinger shutdown counter will reset when the system is disarmed and can be programmed to reset automatically when the 24 hour self test report is generated. (Sub-location 5 of locations 128 and 129).

Silent Zone

This property allows any zone that would ordinarily activate the siren to be programmed as a silent zone i.e. the violation of a silent zone while the system is armed will not activate the siren. However, the relevant reporting code (if programmed) will still be reported.

Zone Reporting Codes

NOTE:

For the following locations, a two digit hexadecimal code must be programmed. To disable a reporting code a double zero (00) must be entered. If a zero is to be reported, it must be entered as hexadecimal value A, i.e. [MODE] [0]. In the event that only 1 of the digits is programmed or an A is incorrectly programmed as a zero the code will not be reported. If domestic reporting is used, only the first digit of the reporting code is required / used.

Page 22

IDS 816 700-283-02I Issued September 2009

Sub-location 3 Alarm Reporting Code

This is the code transmitted when the zone is violated during an arm cycle or if a panic or 24 Hour Zone is violated.

Sub -location 4 Alarm Restoral Reporting Code

The zone restoral code is transmitted when the zone has returned to the “unviolated” condition after triggering an alarm.

Sub-location 5 Bypass Reporting Code

A zone bypass code will be reported when a zone has been bypassed and the panel is armed.

Sub-location 6 Force Arm Reporting Code

This code will be transmitted if a partition is programmed to allow forced arming (arming with a violated zone) and a zone is violated at the time of arming.

Sub-location 7 Tamper Reporting Code

The tamper code will be reported if tamper-by-zone has been enabled and a zone tamper occurs.

Sub-location 8 Tamper Restore Reporting Code

When a zone tamper condition clears, this code will be reported.

Sub-location 9 Swinger Shutdown Reporting Code

The swinger shutdown zone code will be reported if the system is armed and a zone is automatically bypassed as a result of multiple violations of that zone.

Sub-location 10 Swinger Shutdown Restore Reporting Code

If enabled, this code will be reported when a swinger shutdown zone is automatically restored i.e. unbypassed.

Sub-location 11 Zone Programmable Output Location

A programmable output will be pulsed or latched, high or low if a zone causes an alarm condition. If pulsed, the output will be pulsed for the time programmed in sub-location 1 of locations 388 - 394.

Two digits must be programmed for each zone. The first digit references the programmable output number e.g. output 1 to 5 (7 with an expander). The second digit sets the output action. Refer

“

System Programmable Outputs” (Page 30) for a detailed description on Programming Programmable

Outputs.

Sub-location 12 Zone Name Editing (LCD keypads only)

Zones may be given appropriate names, like “Front Door” for zone 1, etc. When the zone is triggered, the display will indicate “Front Door”, instead of “Zone 1”. (Full instructions are included in the LCD keypad manual.)

Page 23

IDS 816 700-283-02I Issued September 2009

7.6.2 System Options

LOCATION 33 Zone Shutdown Count (Default = 5)

Determines the number of times a zone may be violated during an arm cycle before it is automatically bypassed. Select zones individually for this option in locations 1 – 16 (sub-location 2). Valid range of data for this location is 1 to 15.

LOCATION 34 Programmable Zone Loop Response Time

The following applies when option 4 in location 38, is ON

Value

Response Time

Value

Response Time

6 ms

96 ms

1 12 ms

9 108 ms

2 24 ms (default)

10 120 ms

3 36 ms

11 132 ms

48 ms

144 ms

5 60 ms

13 156 ms

6 72 ms

14 168 ms

48 ms

180 ms

The zone loop response is the period of time for which the programmed zone must remain violated before a violation is registered. By default, this table is ignored and a Fixed Zone Loop Response of 100ms is used.

LOCATION 35 Reserved

LOCATION 36 Cross-zone Delay Timer

This location defines the cross-zone delay timer period.

Value

Response Time

0 3 seconds 1 10 seconds 2 15 seconds 3 20 seconds (default) 4 25 seconds 5 30 seconds 6 45 seconds 7 1 Minute

LOCATION 37

Cross-zone Count (Default = 2)

If the panel is armed and the total number of violations of zones programmed as cross-zones reaches this count within the time period programmed into location 36, an alarm condition will be registered. Program a value from [0] to [1] [5]. A [0] will disable this location. Program zones as cross-zones in sublocation 2 of locations 1 to 16. Any single zone enabled for cross-zoning, which is violated continuously for the time specified in location 36 will also register an alarm condition.

Page 24

IDS 816 700-283-02I Issued September 2009

LOCATION 38 Global Options

LED

ON / OFF

Action

A user assigned to any partition may cancel the siren

OFF

Only a user assigned to the partition that triggered the siren may cancel the siren

Enables keypad trouble beep

OFF

Disables keypad trouble beep

Enables telephone line monitoring

OFF

Disables telephone line monitoring

Enables use of programmable loop response time

OFF

Standard 100ms loop response time

Enables keypad beep on communication

OFF

Disables keypad beep on communication

Enables keypad fire, medical and panic keys

OFF

Disables keypad fire, medical and panic keys

Enables the display of bypassed and stay zones when armed in the stay

mode

OFF

Disables the display of bypassed and stay zones when armed in the stay

mode

Enables the siren delay

OFF

Disables the siren delay

Enables zone doubling

OFF

Disables zone doubling (expansion / keypad zones can be used to expand the system to sixteen zones.)

Enable box tamper

OFF

Disable box tamper

Enable siren tamper

OFF

Disable siren tamper

Enable 485 device tamper

OFF

Disable 485 device tamper

Dedicated panic zone – silent

OFF

Dedicated panic zone – audible

Default values are shaded

Page 25

IDS 816 700-283-02I Issued September 2009

LOCATION 39 AC Fail / Restore Time

Value

Delay

0 3 seconds 1 10 seconds 2 15 seconds 3 20 seconds

25 seconds

30 seconds

6 45 seconds 7 1 minute 8 2 minutes

9 3 minutes 10 4 minutes 11 5 minutes 12 10 minutes 13 15 minutes 14 18 minutes

21 minutes

1 hour

17 2 hours 18 3 hours 19 4 hours 20 10 hours

In the event of a power failure the panel will display an instant trouble, but will wait for this period of time before REPORTING the mains failure. The same time period applies before the restoral event is reported and logged. This delay eliminates unnecessary reporting if the AC power is removed for a short time period.

It is important to note that an AC restoral will only be reported if an AC failure was reported, i.e. the delay period was exceeded. Provided the back up battery is in good condition, short AC power failures will not affect the functioning of the alarm system. Select the appropriate value from the table above.

Page 26

IDS 816 700-283-02I Issued September 2009

LOCATION 40 Trouble Display

LED

ON/ OFF

Action

Enable AC fail trouble display

OFF

Disable AC fail trouble display

Enable Comms fail trouble display

OFF

Disable Comms fail trouble display

Enable phone line trouble display

OFF

Disable phone line trouble display

Enable siren tamper trouble display

OFF

Disable siren tamper trouble display

Enable low battery detection trouble display

OFF

Disable low battery detection trouble display

Enable clock loss trouble display

OFF

Disable clock loss trouble display

Enable engineers reset trouble display

OFF

Disable engineers reset trouble display

Enable box tamper trouble display

OFF

Disable box tamper trouble display

Reserved

OFF

Reserved

Enable 485 device trouble display

OFF

Disable 485 device trouble display

Enable bus trouble display

OFF

Disable bus trouble display

Enable Aux. 12V trouble display

OFF

Disable Aux. 12V trouble display

Reserved

OFF

Reserved

Default values are shaded

Location 40 determines which trouble conditions are displayed on the trouble menu. A trouble condition is indicated by a flashing POWER LED. Not withstanding the disabling of a trouble condition from the viewing menu the relevant code will be reported if programmed to do so. Trouble conditions will be reported if programmed to do so in locations 118 to 120, regardless of whether or not they are enabled for display.

The trouble condition can be viewed by holding down the [7] key for one second. See “Viewing Trouble Conditions” in the User Manual.

Page 27

IDS 816 700-283-02I Issued September 2009

LOCATION 41 Siren Time Out Period

Value

Delay

0 3 seconds 1 10 seconds 2 15 seconds 3 20 seconds 4 25 seconds 5 30 seconds 6 45 seconds 7 1 minute 8 2 minutes

3 minutes

4 minutes

11 5 minutes 12 10 minutes 13 15 minutes 14 18 minutes 15 21 minutes

The siren time out period is the period of time for which the siren will sound after an audible alarm condition is registered. Select the appropriate time period from the table above.

LOCATION 42 Siren Delay

When an audible alarm is registered, a delay can be implemented before the siren is triggered. The alarm will however be reported as soon as it occurs. Enable option 8, location 38.

Value

Delay

0 3 seconds 1 10 seconds 2 15 seconds 3 20 seconds

25 seconds

30 seconds

6 45 seconds 7 1 minute 8 2 minutes

9 3 minutes 10 4 minutes 11 5 minutes 12 10 minutes 13 15 minutes 14 18 minutes

21 minutes

LOCATION 43 Keypad Lockout Count (Default = 4 seconds)

If a partition has keypad lockout enabled (Page 46) this value determines the number of consecutive incorrect codes, which will activate a keypad lockout. The keypad will remain locked for the time programmed in location 44. Activating a Keypad Panic will unlock the keypad.

Page 28

IDS 816 700-283-02I Issued September 2009

LOCATION 44 Keypad Lockout Time (Default = 30 seconds)

The value programmed into this location determines the keypad lockout period. The valid range is 0 - 255 seconds.

NOTE: Keypad lockout is enabled by partition. See Partition Options Page 44, sub-location 5.

LOCATION 45 Keypad Sleep Delay (Default = 5 seconds)

The values stored in this location work in the same way as siren delay (table on page 27). The default value is 11, which equates to 5 minutes.

NOTE: This function is set individually per keypad (locations 400 to 407). After this time period, if there is no keypad activity (on this keypad) the backlighting and all other status and alarm indicators will turn off. The power LED and if appropriate, the arm LED will remain on.

LOCATION 46 User and Installer Code Number of Digits

This location determines whether 4 or 6 digit user / installer codes are applicable. Only a value of four or six may be programmed into this location. By default, all codes are four digits in length.

The value programmed into this location has no effect on the download code, which is always 4 digits in length.

Code

Old Four-digit Code

New Six-digit Code

All Previously

Programmed Codes

XXXX XXXX00

Installer Code 9999 999999

Master User Code 1 1234 123456

8. System Reporting Codes (4 x 2 and Domestic)

For all these locations, a two digit hexadecimal code must be programmed. To disable a reporting code a double zero (00) must be entered into the corresponding location. Note that if one of the abovementioned reporting digits is inadvertently omitted or programmed as a zero, the code will not be reported. The exception to this rule is when using domestic reporting where only the first digit is used.

LOCATION 47 AC Failure Reporting Code

The control panel will transmit this code in the event of an AC failure but only after the AC failure delay time has elapsed (location 39).

LOCATION 48 AC Restoral Code

The control panel will transmit this code once the AC restore delay time has elapsed. (location 39). It will however only be reported if an AC failure was registered as per location 47.

Page 29

IDS 816 700-283-02I Issued September 2009

LOCATION 49 Low Battery Reporting Code

A low battery condition is reported when the battery voltage drops below 11.8V for a period longer than 5 minutes or immediately if it drops below 10V.

LOCATION 50 Battery Restore Reporting Code

This code is reported once the battery voltage rises above 12 volts for a period of five minutes.

LOCATION 51 Auto Test Reporting Code

This code is reported at regular intervals. (location 112)

LOCATION 52 Download Access Reporting Code

This code is reported once successful access to the panel has been obtained.

LOCATION 53 Siren Trouble Reporting Code

This code is reported when the siren fuse blows or when the siren or siren wiring is tampered with.

LOCATION 56

Device Tamper Reporting Code

This code is reported when there is a tamper condition on any external device attached to the keypad bus.

LOCATION 57

Keypad Bus Failure Reporting Code

This code is reported when there is a fault on the keypad bus

LOCATION 58 Box Tamper Reporting Code

This code is reported when the box tamper contacts are open for a period exceeding 200 ms.

LOCATION 59 Dedicated Panic Reporting Code

This code is reported when the dedicated panic zone is violated.

LOCATION 60

Phone Line Restoral Reporting Code

If phone line monitoring is enabled (location 38), this code is reported once phone line integrity has been restored to indicate that the phone line has been tampered with.

LOCATION 61

RF Jamming Reporting Code

This reporting code will be reported if the RF receiver module detects a jamming signal for a period exceeding 30 seconds.

LOCATION 62

RF Jamming Restore Reporting Code

This reporting code will be reported once the jamming signal has ceased for a period exceeding 30 seconds.

Page 30

IDS 816 700-283-02I Issued September 2009

9. System Programmable Outputs

Programming the Outputs:

Programmable outputs are able to toggle between different states when specific system events occur. Either single or multiple events may be programmed to a particular output.

For most events the action of an output, when triggered, is programmable. To program these events a two-digit code must be entered. The output action for certain events is fixed – and function driven, the strobe function is one example. For these events, only a single digit code need be programmed.

There are five programmable outputs on the IDS 816 Alarm Panel and a further two programmable outputs on the Wired Zone Expander module. When selecting outputs, programmable outputs on the alarm panels are addressed from “1” to “5“.

Outputs on the Wired Zone Expander are addressed as “6” and “7” – (refer to table 5).

Table 5 : Programmable Output Numbering

Value

Programmed as

Output Addressed

[0]

No output addressed

1 [1] Panel - programmable output 1 2 [2] Panel - programmable output 2 3 [3] Panel - programmable output 3 4 [4] Panel - programmable output 4 5 [5] Panel - programmable output 5 6 [6] Zone expander - programmable output 2 7 [7] Zone expander - programmable output 1

There are 4 permitted output actions, which may be selected. These are listed below in table 6.

Table 6 : Output Actions

Value

Output Action

0 Set output high (Set) 1 Set output low (Reset) 2 Pulse output high 3 Pulse output low

When programming these outputs a two-digit code must be entered. The first digit references the programmable output number (Table 5) and the second digit references the output action (Table 6).

Example:

Entering a value of [1][0] into location 70 will cause Panel Programmable Output 1 to be set (latched) high in the event of an AC Mains Failure. Entering a value of [1][1] into location 71 will cause the Panel Programmable Output 1 to be set (latched) low in the event of an AC Mains Restoral.

When programming a programmable output whose action is fixed only a single digit need be entered. This digit references the programmable output number (Table 5).

Example:

Programming a value of [7] into sub-location 42 of location 129 will cause the Zone Expander Programmable Output 1 to follow the Siren Output for Partition 2.

Page 31

IDS 816 700-283-02I Issued September 2009

NOTE: When connecting any device with a high current requirement to a programmable output a suitable relay must be used. DO NOT connect such devices directly to the programmable outputs as this may damage the output circuitry.

LOCATIONS 70-87 Event Driven Programmable Outputs

Table 7 : Event Driven Programmable Outputs

Loc.

Event

Output

Default Action

70 AC fail programmable output Disabled

AC restore programmable output

Disabled

Low battery programmable output

Disabled

73 Battery restore programmable output Disabled 74 Auto test programmable output Disabled 75 Download programmable output Disabled 76 Siren trouble programmable output Disabled 77 Aux 12V trouble programmable output Disabled 78 Keypad fuse programmable output Disabled 79 485 device tamper programmable output Disabled 80 485 bus failure programmable output Disabled

Box tamper programmable output

Disabled

Dedicated panic programmable output

Pulse high [2]

Communication fail programmable output

Disabled

84 Phone line tamper programmable output Disabled 85 Phone line restore programmable output Disabled 86 RF jamming programmable output Disabled

RF jamming restore programmable output

Disabled

LOCATIONS 95 – 96 Function Driven Programmable Outputs

Table 8 : Function Driven Programmable Outputs

Summary of System function Driven Programmable outputs

Loc.

Function

Output

95 Fire sensor power programmable output Disabled 96 Dual reporting programmable output Disabled

Page 32

IDS 816 700-283-02I Issued September 2009

Figure 6 : Fire Detect Output Sequence

NOTE:

Since multiple conditions may be programmed to a single output, it is essential to ensure that no unwanted conditions are assigned to an output.

Dual Reporting Output

If dual reporting is enabled this output will be set when the panel dials the second phone number, and cleared when it hangs up at the end of transmission. This output follows the hook relay. It may be used to trigger switching from the telephone line to a radio transmitter.

10. System Clock Options

LOCATION 98 System Time

Enter the system time. The format is “hhmm” and is based on a 24-hour clock. (All 4 digits must be entered.)

LOCATION 99 System Day of Month

Enter a two-digit value of the current day of the month. Valid range 01 to 31.

LOCATION 100 System Month

Enter the month as a value from 01 to 12.

LOCATION 101 System Year

Enter the current year as a four-digit value e.g. 2007.

LOCATION 102

System Day of Week

Enter the current day of the week. Refer to table 9.

Page 33

IDS 816 700-283-02I Issued September 2009

Table 9 : Value for Day of the Week

Value

Day

1 Monday 2 Tuesday 3 Wednesday

Thursday

Friday

Saturday

7 Sunday

LOCATION 103 Month to Start Daylight Saving

Enter the month when Daylight Saving will commence.

LOCATION 104 Day of Week to Start Daylight Saving

Enter which day of the week Daylight saving is to commence. Refer to location 102 Table 9.

LOCATION 105 Week of Month to Start Daylight Saving

Enter which week of the month Daylight Saving is to commence. If the last week of the month is wanted, program a five (5).

LOCATION 106 Month to Return to Standard Time

Enter the month when Daylight Saving reverts to standard time.

LOCATION 107 Day of Week to Return to Standard Time

Enter which day of the week (Table 9) that Daylight Saving returns to standard time.

LOCATION 108

Week of Month to Return to Standard Time

Enter which week of the month Daylight Saving will return to standard time. If it is to be the last week of the month, program a five (5).

LOCATION 109 Daylight Saving Time Offset

This location is used for setting the Daylight Saving offset. Enter the number of minutes the clock will offset - Valid range 0 to 250.

Page 34

IDS 816 700-283-02I Issued September 2009

11. Communicator Options

LOCATION 110 Communication Delay

Value

Delay

0 3 seconds 1 10 seconds 2 15 seconds 3 20 seconds 4 25 seconds

30 seconds

45 seconds

7 1 minute 8 2 minutes

9 3 minutes 10 4 minutes 11 5 minutes 12 10 minutes 13 15 minutes 14 18 minutes 15 21 minutes

If delayed communications is enabled for either partition, (locations 128 and 129) the panel will wait for this period before reporting zone violations and restorals. If the alarm is cancelled within this time zone, violations and restorals will not be reported. Violations will however be logged in the event log. Panic events will be reported instantly – regardless of any selected delay period.

LOCATION 111

Reporting Options

LED

On / Off

Action

ON Tone dialling enabled

OFF Pulse dialling enabled

ON Join the telephone numbers together

OFF Keep two separate telephone numbers

ON Enable dual reporting

OFF Disable dual reporting

Single reporting options (LED 3 off)

Reports to secondary number only after failing on attempting the primary number. (Panic event initiates dual reporting)

OFF

Alternates reporting attempts between both

numbers until successful with one of them. (Single reporting, regardless of panic)

Default values are shaded

Page 35

IDS 816 700-283-02I Issued September 2009

NOTE:

 The panel may be programmed to report to a single central station (single reporting) or to report

to 2 central stations (dual reporting).

 When programmed for single reporting, the panel default will alternate attempts between the two

“equally ranked” stored numbers. With LED 4 on, the secondary number will only be called if the attempt to report to the primary number fails. In either case, the number of attempts (per phone number) will be equal to the number stored in location 115, with a default value of 6.

 The primary and secondary telephone numbers may be joined to provide for a single telephone

number of 48 digits in length.

LOCATION 112 Auto Test Interval

Value

Time Period

0 Report every hour

Report daily (default)

2 Every two days 3 Every three days 4 Every four days 5 Every five days 6 Every six days 7 Every seven days 8 Every eight days

9 Every nine days 10 Every ten days 11 Every eleven days

Every twelve days

Every thirteen days

14 Every fourteen days 15 Every fifteen days

The value programmed into this location will determine the duration of time between Auto Tests.

LOCATION 113 Auto Test Time

Enter the time when the auto test will be reported. The format is “hhmm” based on a 24-hour clock. (All four digits must be entered.)

Example:

If a value of [7] was programmed into location 112 and [1400] was programmed into this location, the auto test would be sent weekly at 2:00pm.

LOCATION 114 Number of Account Code Digits (Default = 4)

Most reporting formats use a 4-digit account code. Program a 6 into this location to enable 6-digit account code reporting. This option is not supported by Contact ID.

LOCATION 115 Number of Dial Attempts (Default = 6)

This location determines the maximum number of dial attempts that the panel will make in order to contact the base station.

Page 36

IDS 816 700-283-02I Issued September 2009

NOTE: Entering [0] into this location will disable the dialler.

LOCATION 116 Primary Communicator Format

Value

Format Name

Description

0 Ademco Express Dual Tone HS 1 FBI 4 x 2 ( With Parity) 1.8kHz TX, 2.3kHz HS, 40PPS 2 FBI 4 x 2 (No Parity) 1.8kHz TX, 2.3kHz HS, 20PPS 3 Silent Knight 4 x 2 Fast 1.9kHz TX, 1.4kHz, 20PPS 4 Silent Knight 4 x 2 Slow 1.9kHz TX, 1.4kHz, 20PPS

5 (Default) Contact ID Dual Tone HS

6 Domestic Reporting 0.5kHz TX, Blind, 20PPS

TX = Transmit HS = Handshake PPS = Pulses per Second

The value entered into location 116 selects the primary communicator format. Select from the table above the value appropriate to the required format. During communication, the green LED on the PCB will come on indicating that the panel has taken the telephone off-hook. If programmed accordingly (location 38), the keypad will beep after receiving a handshake from the base station. This indicates a successful transmission of data.

LOCATION 117 Secondary Communicator Format

If dual reporting is enabled then this format will be used to report to phone number 2. (Table for location

116.)

NOTES ON DUAL REPORTING

When dual reporting is enabled, it is possible to select two different formats. In this instance, all data will be transmitted to each phone number (i.e. reported twice) using a different format per phone number.

NOTES ON CONTACT ID

If the panel has been programmed to use the Contact ID, it will not be necessary to program individual reporting codes. Provision is made to enable/disable the reporting of certain groups of codes. (location 118 to 120). Table 10 contains a list of standard (default) Contact ID reporting codes. Any event that relates to a specific zone, or to a specific user, will have the relevant zone/user number appended to the end of the Contact ID reporting code.

Page 37

IDS 816 700-283-02I Issued September 2009

Table 10 : Standard Contact ID Reporting Codes

Description

Codes

Description

Codes

Keypad medical 1100 Cancel 1406 Fire 1110 Open by download 1407

Keypad Fire

1110

Open with key-switch

1409

Panic

1120

Low battery

1302

Panic zone 1120 Sounder/Relay trouble 1320 Keypad panic 1120 Expansion module fail 1333 Duress 1121 Zone/Sensor bypass 1570 Burglary violation 1130 Zone/Sensor bypass restoral 3570 Perimeter violation 1131 Burg. bypass 1573 Interior violation 1132 Test report 1602 24 Hour (safe) violation 1133 Panic restore 3120 Entry/Exit violation 1134 Zone restoral 3130 Day/night violation 1135 Keypad tamper restore 3137 Outdoor violation 1136 Zone restoral 3130

Tamper violation

1137

Sensor tamper restore

3144

Keypad tamper

1137

Expansion module tamper restore

3145

Keypad lockout 1137 RF low battery restore 3384 Near alarm violation 1138 Close by user 3401 Tamper by zone 1144 Close by auto arm 3403 Expansion module tamper 1145 Close by download 3407 Exp. module low bat 1338 Close with key-switch 3409 RF receiver jam detect 1344 Expansion module fail restore 3333 Long range transmitter fault 1353 AC loss 3321 Loss of supervision RF 1381 AC restoral 3333

RF low battery

1384

Low battery restore

3302

Open by user

1401

Sounder/Relay restore

3320

NOTES ON DOMESTIC REPORTING:

If Dual Reporting is enabled, Domestic reporting may either be reported to 2 telephone numbers or using the dual reporting option, report to a central station as well as to an individual mobile phone etc. This format provides for a simple form of easily identifiable remote alarm which may be reported to an office, mobile phone etc. A series of tones is transmitted to the phone, which notifies the user that an alarm condition has occurred. If a 1 is programmed to a location, a single beep will be heard if that particular alarm condition occurs. If a 2 is programmed to a location, 2 beeps will be heard etc.

NOTE:

If the system is armed using the quick arm key [1] the system will report a close by user 35.

If the system is armed by means of a key switch or non-latching remote receiver connected to

an arm/disarm zone the system will report a close by user 34.

Enabling / Disabling Reporting Groups

Locations 118 to 120 are used to either enable or disable the reporting of groups of reporting codes when using Contact ID.

Page 38

IDS 816 700-283-02I Issued September 2009

LOCATION 118 Global Group Reporting Code Enable / Disable 1

LED

ON / OFF

Action

ON Enable close reporting code

OFF Disable close reporting code

ON Enable stay close reporting code

OFF Disable stay close reporting code

Enable open reporting code

OFF

Disable open reporting code

ON Enable cancel reporting code

OFF Disable cancel reporting code

ON Enable alarm reporting code

OFF Disable alarm reporting code

ON Enable restore reporting code

OFF Disable restore reporting code

ON Enable bypass reporting code

OFF Disable bypass reporting code

ON Enable force reporting code

OFF

Disable force reporting code

Enable tamper reporting code

OFF Disable tamper reporting code

ON Enable tamper restore reporting code

OFF Disable tamper restore reporting code

ON Enable shutdown reporting code

OFF Disable shutdown reporting code

ON Enable shutdown restore reporting code

OFF Disable shutdown restore reporting code

ON Enable AC fail reporting code

OFF Disable AC fail reporting code

Enable AC restore reporting code

OFF

Disable AC restore reporting code

ON Enable low battery reporting code

OFF Disable low battery reporting code

ON Enable battery restore reporting code

OFF Disable battery restore reporting code

Default values are shaded

Page 39

IDS 816 700-283-02I Issued September 2009

LOCATION 119 Global Group Reporting Code Enable / Disable 2

LED

ON / OFF

Action

ON Enable test report reporting code

OFF

Disable test report reporting code

Enable download reporting code

OFF

Disable download reporting code

ON Enable siren fuse trouble reporting code

OFF Disable siren fuse trouble reporting code

ON Enable Aux. 12V trouble reporting code

OFF Disable Aux. 12V trouble reporting code

ON Enable keypad fuse trouble reporting code

OFF Disable keypad fuse trouble reporting code

ON Enable 485 device tamper reporting code

OFF Disable 485 device tamper reporting code

ON Enable 485 bus tamper reporting code

OFF

Disable 485 bus tamper reporting code

Enable box tamper reporting code

OFF Disable box tamper reporting code

ON Enable dedicated panic reporting code

OFF Disable dedicated panic reporting code

ON Enable phone line restoral reporting code

OFF Disable phone line restoral reporting code

ON Enable duress reporting code

OFF Disable duress reporting code

ON Enable keypad panic reporting code

OFF Disable keypad panic reporting code

Enable keypad fire reporting code

OFF

Disable keypad fire reporting code

ON Enable keypad medical reporting code

OFF Disable keypad medical reporting code

ON Enable keypad lockout reporting code

OFF Disable keypad lockout reporting code

ON Enable access reporting code

OFF Disable access reporting code

Default values are shaded

Page 40

IDS 816 700-283-02I Issued September 2009

LOCATION 120 Global Group Reporting Code / Disable 3

LED

ON / OFF

Action

ON Enable RF jamming

OFF

Disable RF jamming

Enable RF jamming restore

OFF

Disable RF jamming restore

RESERVED

OFF

RESERVED

OFF

RESERVED

OFF

RESERVED

OFF

RESERVED

OFF

RESERVED

OFF

RESERVED

OFF

Default values are shaded

11.1 Programming Telephone Numbers

For the telephone number locations, a value of [0] is used as a termination digit. It is important therefore that any zeros (0) in the telephone number itself be entered as a [10]. All hexadecimal values are entered using the mode key (See table 2, page 17).

Enter numbers consecutively with no other key presses between each digit.

To dial a “0” program a table 2 [10] – by pressing [MODE] [0] To dial a “*” program an [11] - by pressing [MODE] [1] To dial a "#" program a [12] - by pressing [MODE] [2]

Inserting pauses A pause may be inserted at any point within the telephone number: Entering a value of [13] (by pressing [MODE] [3]) will provide a 12-second pause and a value of [15] (by pressing [MODE] [5]) will provide

a 4-second pause.

To terminate a telephone number, program a [0] immediately after the last digit of the telephone number.

Example: Phone number 1 is to be dialled as follows: [0] followed by a 4 second pause then [0317051373]. The key sequences are as follows:

Page 41

IDS 816 700-283-02I Issued September 2009

Data entered

Explanation

[INSTALLER CODE][*] To enter program mode

[1][2][1][*] To enter location 121 (phone number 1)

[MODE][0] To dial the zero [MODE][5] This programmes the 4 second pause

[MODE][0][3][1] This programmes the area code

[7][MODE][0][5][1][3][7][3]

The remainder of the number

[0]

To mark the end of the number

[#] To exit program mode

11.2 Telephone Number Storage Locations

LOCATION 121 Phone Number 1

This location contains the primary telephone number. A maximum of 24 digits can be entered. Enter the digits consecutively and after the last digit has been entered, terminate with a [0].

LOCATION 122 Phone Number 2

This location contains the secondary telephone number. A maximum of 24 digits can be entered. Enter the digits consecutively and after the last digit has been entered, terminate with a [0].

11.3 Download Options

LOCATION 123

Download Options

LED

ON / OFF

Action

Enable fax defeat

OFF

Disable fax defeat

Enable forced answer

OFF Disable forced answer

ON Enable auto pickup

OFF Disable auto pickup

ON Enable call-back

OFF Disable call-back

Default values are shaded

Fax defeat is useful for downloading when a fax or answering machine is connected to the same phone line as the alarm panel. If this feature is enabled, dial the panel and hang up before three rings. Dial the panel again within one minute. The panel will then pick up the call on the first ring thereby preventing the fax / answering machine from answering the call before the alarm.

If forced answer is enabled the [8] key may be used to force the panel to go off hook,

“answering the line”.

If enabled, Auto Pickup will pick up the line after the number of rings programmed into location

124. The Call-back feature when enabled, allows the download software/PC to request that the

panel call it back using the phone number as programmed into location 125.

Page 42

IDS 816 700-283-02I Issued September 2009

LOCATION 124 Number of Rings to Answer (Default = 15)

This location determines the number of rings before the panel “answers" the telephone line. In the event that the panel answers the call and no valid download log on sequence is received within 40 seconds, the panel will terminate the call.

LOCATION 125

Call-back Phone Number

If Call-back is enabled in Download Options (location 123) the phone number programmed into this location will be used to respond to a call-back request from the IDS Download Software/PC.

12. Partition Setup

LOCATIONS 128 – 129 Partition Setup

Location 128 - Partition One. Location 129 - Partition Two.

Sub-location 1 Partition Zone Allocation

This location is bitmapped with each LED representing a zone. LED’s that are on represent the zones in the selected partition. Enter the number of the zone followed by the [*] key to select or deselect zones. By default, all zones are allocated to partition 1 and no zones are allocated to partition 2.

Sub-location 2 Primary Account Code

This account code is used if single reporting has been enabled. If dual reporting is enabled then this account code is reported to telephone number 1.

Sub-location 3 Secondary Account Code

This account code is only used when dual reporting is enabled. It is reported to Telephone Number 2.

Page 43

IDS 816 700-283-02I Issued September 2009

Sub-location 4 Partition Arm Options

LED

On / Off

ACTION

ON Enable instant arm

OFF Disable instant arm

ON Enable instant key-switch arm

OFF Disable instant key-switch arm

ON Enable quick arm key

OFF Disable quick arm key

Enable quick stay arm key

OFF

Disable quick stay arm key

ON Enable auto stay arm if no exit zone is triggered

OFF Panel away arms regardless if zone is triggered

Enable auto stay arm if no exit zone is triggered when arming with a key-switch (or remote)

OFF

Disable auto stay arm if no exit zone is triggered when

arming with a key-switch (or remote)

ON Enable forced arm

OFF Disable forced arm

Enable zone bypassing

OFF

Disable zone bypassing

Enable arm with zones in the entry route violated

OFF Disable arm with zones in the entry route violated

ON Enable siren toot on arm

OFF Disable siren toot on arm

ON Enable siren toot on disarm

OFF Disable siren soot on disarm

ON Enable the entry beep

OFF Disable the entry beep

ON Enable the exit beep

OFF Disable the exit beep

Enable engineers reset

OFF

Disable engineers reset

ON Enable auto disarm

OFF Disable auto disarm

Default values are shaded

Quick Arm:

This option allows the user to arm the panel by holding down the [1] key for two seconds until the keypad beeps.

Force Arm:

With this option enabled, the panel will arm with violated zones e.g. an open window. When the panel arms, any violated zone is bypassed. If bypassed zones restore during the arm cycle (e.g. a window is closed), the zone is automatically re-activated (un-bypassed).

Siren Toot on Away Arm / Disarm:

This option allows the user an audible confirmation that arming or disarming of the panel has occurred. The siren can be programmed to give a short beep after successful arming, and two short beeps after disarming. This is useful when used in conjunction remote or key-switch arming/disarming.

Page 44

IDS 816 700-283-02I Issued September 2009

Engineer Reset:

If enabled this option prevents arming the panel after an alarm condition has occurred. The panel can only be armed after the engineer has entered a valid installer code. A trouble condition will be displayed on the keypad if enabled in location 40.

Sub-location 5 Partition Options

LED

ON / OFF

Action

Enable automatic re-enabling of shutdown zones at the time of the dialler test.

OFF

Disable automatic re-enabling of shutdown zones at the time of the dialler test.

Enable bypassing of common zones

OFF

Disable bypassing of common zones

ON Enable delay before communications

OFF Disable delay before communications

ON Enable keypad lockout

OFF Disable keypad lockout

ON Enable user phone access

OFF Disable user phone access

ON Enable silent keypad panic

OFF Disable silent keypad panic

Default values are shaded

Sub-location 6 Exit Delay Period

Value

Time-out Delay

Value

Time-out Delay

0 3 Seconds 8 2 Minutes 1 10 Seconds 9 3 Minutes

15 Seconds

4 Minutes

20 Seconds

5 Minutes

4 25 Seconds 12 10 Minutes 5 30 Seconds (default) 13 15 Minutes 6 45 Seconds 14 18 Minutes 7 1 Minute 15 21 Minutes

The exit delay will begin after the entry of a valid user code (or pressing of the [1] or [6], initiating the quick-arm function). During this period, it is permissible to violate Entry/Exit and Follower zones without causing an alarm condition thus allowing exit from the premises. Select the appropriate exit delay period from the table above. If an instant zone is violated during this period, an alarm condition will immediately be registered. Select the appropriate value for the primary exit delay from the table.

Sub-location 7 Primary Entry Delay Time

(Values identical to Sub-location 6) This entry delay begins after the violation of a primary Entry/Exit zone. During this, it is permissible to violate follower zones without causing an alarm condition if an Entry/Exit zone was violated first. If a follower zone is violated without a prior Entry/Exit zone violation, it will be treated as an instant zone. If an instant zone is violated during this period, an alarm condition will immediately be registered. Select the appropriate value for the primary entry delay from the same table for sub-location 6.

Page 45

IDS 816 700-283-02I Issued September 2009

Sub-location 8 Secondary Entry Delay

(Values identical to Sub-location 6) The secondary entry delay applies to secondary Entry/Exit zones. Once an entry has been initiated, subsequent violations of any entry zone will NOT reset the entry time. Use the same table from Sub-location 6 to look up the value for the time interval required.

Sub-location 9 Auto Arm Time (Default = disabled)

This sub-location stores the time at which a particular partition will auto arm. The data format entered into this location is “hhmm” based on a 24-hour clock. Example: To auto arm at 11:35pm, enter 2335. All four digits must be entered, include any leading zeros (0100 for 1 am).

To disable this feature, ensure that no day of the week is selected in sub-location 10.

Sub-location 10 Auto Arm Days (Default = all OFF)

This Bitmapped sub-location sets the days on which the partition will auto arm at the time programmed in sub-location 9.

LED’s

Days of the Week

LED 1

Monday

LED 2

Tuesday

LED 3

Wednesday

LED 4 Thursday LED 5 Friday LED 6 Saturday LED 7 Sunday All OFF (Auto arm disabled)

Sub-location 11 Auto Disarm Time

This sub-location will store the time that the partition will auto disarm. The format of data entered into this location is “hhmm” based on a 24-hour clock. For example: To auto disarm at 11:35 am, enter 1135.

Sub-location 12 Auto Disarm Days

This Bitmapped sub-location sets the days on which the partition will auto disarm at the time programmed in sub-location 11.

LED’s

Days of the Week

LED 1 Monday LED 2 Tuesday

LED 3

Wednesday

LED 4

Thursday

LED 5 Friday LED 6 Saturday LED 7 Sunday

All OFF (Auto arm disabled) NOTE: Auto Disarm, if required, must be enabled per partition. (Sub-location 4).

Page 46

IDS 816 700-283-02I Issued September 2009

Sub-location 13 Auto Arm Delay

This location selects the delay period for the keypad buzzer warning, which is initiated before the panel auto arms. At the completion of the Auto Arm Delay, the panel will arm. A valid user code entered during the delay period will cancel the auto arming.

Value

Delay

Value

Delay

0 3 seconds 8 (Default) 2 minutes 1 10 seconds 9 3 minutes 2 15 seconds 10 4 minutes 3 20 seconds 11 5 minutes 4 25 seconds 12 10 minutes 5 30 seconds 13 15 minutes 6 45 seconds 14 18 minutes 7 1 minute 15 21 minutes

Sub-location 14 Reserved

Sub-location 15

Reserved

Partition Reporting Codes (for 4 x 2 & Domestic)

For all these locations, a two digit hexadecimal code must be programmed. To disable a reporting code, a double zero (00) must be entered into the corresponding location. Note that if one of the abovementioned reporting digits is inadvertently omitted or programmed as a zero, the code will not be reported. The exception to this rule is when using domestic reporting where only the first digit is used.

Sub-location 16 Duress Reporting Code

This code is reported when a duress code is entered.

Sub-location 17 Keypad Panic Reporting Code

This code is reported when the [P] key on a keypad is held down for one second.

Sub-location 18

Keypad Fire Reporting Code

This code is reported when the [F] key on the keypad is held down for one second.

Sub-location 19 Keypad Medical Reporting Code

This code is reported when the [M] key on the keypad is held down for one second.

Sub-location 20 Keypad Lockout Reporting Code

This code is reported when a keypad lockout condition occurs.

Sub-locations 21 – 44 Partition Programmable Outputs

See “System Programmable Outputs” (Section 9, page 30) for details on programming the programmable outputs. The table below summarises the partition specific events that can be assigned to the outputs.

Page 47

IDS 816 700-283-02I Issued September 2009

Summary of Partition Event Driven Programmable Outputs

Sub-loc

Event

Output

Default Action

21 Close programmable output 3 Set high [0] 22 Stay close programmable output Disabled 23 Open programmable output 3 Set low [1] 24 Cancel programmable output Disabled 25 Alarm restoral programmable output Disabled 26 Bypass programmable output Disabled 27 Forced arm programmable output Disabled 28 Zone tamper programmable output Disabled

Zone tamper restoral programmable

output

Disabled

30 Zone shutdown programmable output Disabled

Zone shutdown restoral programmable output

Disabled

32 Keypad panic programmable output 1 Pulse high [2] 33 Keypad fire programmable output Disabled

Keypad medical programmable output

Disabled

35 Keypad lockout programmable output Disabled 36 Duress programmable output 1 Pulse high [2] 37 Verifies alarm programmable output Disabled 38 Burglary programmable output 2 Pulse high [2] 39 Panic programmable output 1 Pulse high [2] 40 Fire programmable output Disabled 41 Tamper zone programmable output Disabled 42 Siren programmable output Disabled

Strobe programmable output

Disabled

Chime programmable output

Disabled

Sub-location 45 Clear Programmable Outputs on Disarming

This bitmapped sub-location allows any programmable output to be cleared (set low) on disarming. The output(s) to be cleared will be displayed by zone LED’s that are on, representing the output i.e. zone 1 = output 1 etc. To toggle the status of the output, press the [NUMBER OF OUTPUT] [*] if the LED was off it will now come on and visa versa.

(To exit this mode press [#])

LED

Output

1 Panel - programmable output 1 2 Panel - programmable output 2 3 Panel - programmable output 3 4 Panel - programmable output 4

Panel - programmable output 5

Wired zone expander - programmable output 2

7 Wired zone expander - programmable output 1

Page 48

IDS 816 700-283-02I Issued September 2009

13. User Options

LOCATIONS 136 – 167 Individual User Code Setup

The IDS 816 provides for 32 user codes. These locations allow the installer to configure the user code properties.

Table 11 : User Code Locations

Loc Number

User Number

Loc Number

User Number

136

User 1

152

User 17

137 User 2 153 User 18 138 User 3 154 User 19 139 User 4 155 User 20 140 User 5 156 User 21 141 User 6 157 User 22 142 User 7 158 User 23 143 User 8 159 User 24 144 User 9 160 User 25 145 User 10 161 User 26 146 User 11 162 User 27

147

User 12

163

User 28

148

User 13

164

User 29

149 User 14 165 User 30 150 User 15 166 User 31 151 User 16 167 User 32

When the panel is defaulted, User Code 1 defaults to 1234 and is a Master User Code. All other User Codes are disabled.

Sub-location 1 Assigned to Partitions

This bitmapped sub-location determines which partition a user code is assigned to. By default, User Code 1 is assigned to Partitions 1 and 2. All other User Codes are assigned to Partition 1 only. (Depending on sub-location 2, bit 1). Change partitions by holding [MODE] for 1 second, [2] [*], in user mode – provided that the keypad is Global. (Sub-location 2, bit 4).

LED

Partition

LED 1 Partition one LED 2 Partition two

Sub-location 2 User Code Properties

This is a bitmapped sub-location.

LED

User Option

1 Master user 2 Duress code 3 Arm to disarm code (maid’s code) 4 Global Arm/Disarm

Page 49

IDS 816 700-283-02I Issued September 2009

NOTE:

A master user code allows for the programming of other user codes in User Programming Mode.

User Reporting Codes (for 4x 2 and Domestic Reporting)

Sub-location 3 Close Reporting Code

This code is reported when the panel is AWAY ARMED.

Sub-location 4 Stay Close Reporting Code

This code is reported when the panel is STAY ARMED.

Sub-location 5 Open Reporting Code

This code is reported when the panel is disarmed.

Sub-location 6 Siren Cancel Reporting Code

If the siren is sounding and the siren is cancelled using a valid user code, a cancel code will be reported. Cancelling a silent alarm or silent panic will not cause the cancel siren code to be reported.

14. Programmable Output Options

LOCATIONS 388 – 394 Programmable Output Timing Setup

Locations 388 to 394 allow the installer to setup the timing characteristics of each programmable output individually.

Location

Output No.

Output Type

388 1 Panel prog. output 1 389 2 Panel prog. output 2 390 3 Panel prog. output 3 391 4 Panel prog. output 4 392 5 Panel prog. output 5 393 6 Zone expander prog. output 2 394 7 Zone expander prog. output 1

Page 50

IDS 816 700-283-02I Issued September 2009

Sub-location 1 Output Pulse Time

This sub-location determines the length of time for which an output will pulse.

Value

Delay

Value

Delay

0 (Default)

3 seconds

2 minutes

10 seconds

9 3 minutes

15 seconds

4 minutes

3 20 seconds 11 5 minutes 4 25 seconds 12 10 minutes 5 30 seconds 13 15 minutes 6 45 seconds 14 18 minutes 7 1 minute 15 21 minutes

Output Scheduling

Outputs can be scheduled to set and reset at specified times on specific days of the week. To disable scheduling of an output ensure that all “days” are deselected.

Sub-location 2

Schedule ON Time

Enter the time using “hhmm” format at which the output is to be SET. (MUST be four digits)

Sub-location 3 Schedule ON Days

This bitmapped sub-location determines on which day(s) an output will be set.

LED

Days of the Week

Monday

Tuesday

Wednesday

4 Thursday 5 Friday 6 Saturday 7 Sunday

Sub-location 4 Schedule OFF Time

Enter the time using “hhmm” format at which the output is to be RESET. All four digits must be entered, include any leading zeros (0100 for 1 am, for example).

Sub-location 5 Schedule OFF Days

This bitmapped sub-location determines on which day(s) an output will be scheduled to RESET.

LED

Days of the Week

Monday

Tuesday

3 Wednesday 4 Thursday 5 Friday 6 Saturday 7 Sunday

Page 51

IDS 816 700-283-02I Issued September 2009

15. Keypad Options

LOCATIONS 400 – 407 Individual Keypad Setup

These locations allow the installer to setup the individual keypad properties.

Location Keypad ID

400 Keypad 1

401

Keypad 2

402

Keypad 3

403

Keypad 4

404 Keypad 5 405 Keypad 6 406 Keypad 7 407 Keypad 8

Sub-location 1 Default Keypad Partition (Default = Partition 1)

This defines the partition to which a keypad will automatically return after viewing another partition.

Sub-location 2 Keypad Options

(Change partitions by entering [MODE] [*] [Partition Number] [*], in USER MODE)

LED

ON / OFF

Action

The keypad will timeout back to its default partition

after it has been used to view another partition

OFF

The keypad will not timeout and will continue to show current partition information

ON Keypad sleep mode enabled

OFF Keypad sleep mode disabled

ON Enable keypad zone

OFF Disable keypad zone

ON Enable global keypad status

OFF Disable global keypad status

Default values are shaded

* LED 4 must be ON in order for LED 1 to have any effect.

 The Global Keypad Options will allow all sixteen zones to be displayed regardless of the partition

to which either the keypad or zones are assigned.

 Keypad zones are mapped according to Keypad ID as shown in the table.

Page 52

IDS 816 700-283-02I Issued September 2009

Keypad Zone

Zone Number

Keypad ID 1 Zone 16 Keypad ID 2 Zone 15 Keypad ID 3 Zone 14 Keypad ID 4 Zone 13 Keypad ID 5 Zone 12

Keypad ID 6

Zone 11

Keypad ID 7

Zone 10

Keypad ID 8 Zone 9

16. Installer Options

LOCATION 444 Reset Switch Disable (Default = 0)

Value

Action

10 Disable reset switch

Any other value

Enable reset switch

For the detailed operation of this switch, refer to Section 3: Hardware Reset Switch.

LOCATION 445 Installers Code (Default = 9999)

Enter the installer code into this location.

LOCATION 446 View Keypad ID

View the data in this location to ascertain the Keypad ID

Page 53

IDS 816 700-283-02I Issued September 2009

Index of Programming Locations

LOCATION 0 Defaulting of the Panel or Master User Code ------------------------ 19 LOCATIONS 1 – 16 Individual Zone Setup -------------------------------------------------------- 19

Sub-location 1 ZoneType -------------------------------------------------------------------------- 19 Sub-location 2 Zone Properties (Defaults shaded) ------------------------------------------ 21 Sub-location 3 Alarm Reporting Code ---------------------------------------------------------- 22 Sub-location 4 Alarm Restoral Reporting Code----------------------------------------------- 22 Sub-location 5 Bypass Reporting Code -------------------------------------------------------- 22 Sub-location 6 Force Arm Reporting Code ---------------------------------------------------- 22 Sub-location 7 Tamper Reporting Code -------------------------------------------------------- 22 Sub-location 8 Tamper Restore Reporting Code --------------------------------------------- 22 Sub-location 9 Swinger Shutdown Reporting Code ----------------------------------------- 22 Sub-location 10 Swinger Shutdown Restore Reporting Code ------------------------------ 22 Sub-location 11 Zone Programmable Output Location--------------------------------------- 22 Sub-location 12 Zone Name Editing (LCD Keypads only) ----------------------------------- 22

LOCATION 33 Zone Shutdown Count (Default = 5) ------------------------------------ 23 LOCATION 34 Programmable Zone Loop Response Time --------------------------- 23 LOCATION 35 Reserved -------------------------------------------------------------------------- 23 LOCATION 36 Cross-zone Delay Timer ----------------------------------------------------- 23 LOCATION 37 Cross-zone Count (Default = 2) ------------------------------------------ 23 LOCATION 38 Global Options ------------------------------------------------------------------ 24 LOCATION 39 AC Fail / Restore Time ------------------------------------------------------- 25 LOCATION 40 Trouble Display ----------------------------------------------------------------- 26 LOCATION 41 Siren Time Out Period ------------------------------------------------------- 27 LOCATION 42 Siren Delay ----------------------------------------------------------------------- 27 LOCATION 43 Keypad Lockout Count (Default = 4) ----------------------------------- 27 LOCATION 44 Keypad Lockout Time (Default = 30 seconds) ---------------------- 28 LOCATION 45 Keypad Sleep Delay ---------------------------------------------------------- 28 LOCATION 46 User and Installer Code - Number of Digits -------------------------- 28 LOCATION 47 AC Failure Reporting Code------------------------------------------------- 28 LOCATION 48 AC Restoral Code ------------------------------------------------------------- 28 LOCATION 49 Low Battery Reporting Code----------------------------------------------- 29 LOCATION 50 Battery Restore Reporting Code ----------------------------------------- 29 LOCATION 51 Auto Test Reporting Code -------------------------------------------------- 29 LOCATION 52 Download Access Reporting Code -------------------------------------- 29 LOCATION 53 Siren Trouble Reporting Code -------------------------------------------- 29 LOCATION 56 Device Tamper Reporting Code ------------------------------------------ 29 LOCATION 57 Keypad Bus Failure Reporting Code ----------------------------------- 29 LOCATION 58 Box Tamper Reporting Code ---------------------------------------------- 29 LOCATION 59 Dedicated Panic --------------------------------------------------------------- 29 LOCATION 60 Phone Line Restoral RC ----------------------------------------------------- 29 LOCATION 61 RF Jamming RC ---------------------------------------------------------------- 29 LOCATION 62 RF Jamming Restore RC ---------------------------------------------------- 29 LOCATIONS 70 – 87 Event Driven Programmable Outputs ----------------------------------- 31 LOCATIONS 95 – 96 Function Driven Programmable Outputs ------------------------------ 31 LOCATION 98 System Time --------------------------------------------------------------------- 32 LOCATION 99 System Day of Month--------------------------------------------------------- 32 LOCATION 100 System Month ------------------------------------------------------------------- 32 LOCATION 101 System Year --------------------------------------------------------------------- 32 LOCATION 102 System Day of Week ---------------------------------------------------------- 32 LOCATION 103 Month to Start Daylight Saving ------------------------------------------- 33 LOCATION 104 Day of Week to Start Daylight Saving ---------------------------------- 33

Page 54

IDS 816 700-283-02I Issued September 2009

LOCATION 105 Week of Month to Start Daylight Saving ------------------------------- 33 LOCATION 106 Month to Return to Standard Time -------------------------------------- 33 LOCATION 107 Day of Week to Return to Standard Time------------------------------ 33 LOCATION 108 Week of Month to Return to Standard Time -------------------------- 33 LOCATION 109 Daylight Saving Time Offset ----------------------------------------------- 33 LOCATION 110 Communication Delay -------------------------------------------------------- 34 LOCATION 111 Reporting Options ------------------------------------------------------------- 34 LOCATION 112 Auto Test Interval -------------------------------------------------------------- 35 LOCATION 113 Auto Test Time ------------------------------------------------------------------ 35 LOCATION 114 Number of Account Code Digits (Default = 4) ---------------------- 35 LOCATION 115 Number of Dial Attempts (Default = 6) --------------------------------- 35 LOCATION 116 Primary Communicator Format ------------------------------------------- 36 LOCATION 117 Secondary Communicator Format --------------------------------------- 36 LOCATION 118 Global Group Reporting Code Enable / Disable 1 ----------------- 38 LOCATION 119 Global Group Reporting Code Enable / Disable 2 ----------------- 39 LOCATION 120 Global Group Reporting Code / Disable 3 ---------------------------- 40 LOCATION 121 Phone Number 1 --------------------------------------------------------------- 41 LOCATION 122 Phone Number 2 --------------------------------------------------------------- 41 LOCATION 123 Download Options ------------------------------------------------------------- 41 LOCATION 124 Number of Rings to Answer (Default = 15) --------------------------- 42 LOCATION 125 Call-back Phone Number --------------------------------------------------- 42 LOCATIONS 128 – 129 Partition Setup ------------------------------------------------------------------ 42

Sub-location 1 Partition Zone Allocation -------------------------------------------------------- 42 Sub-location 2 Primary Account Code ---------------------------------------------------------- 42 Sub-location 3 Secondary Account Code ------------------------------------------------------ 42 Sub-location 4 Partition Arm Options------------------------------------------------------------ 43 Sub-location 5 Partition Options ------------------------------------------------------------------ 44 Sub-location 6 Exit Delay Period ----------------------------------------------------------------- 44 Sub-location 7 Primary Entry Delay Time ------------------------------------------------------- 44 Sub-location 8 Secondary Entry Delay ---------------------------------------------------------- 45 Sub-location 9 Auto Arm Time (Default = disabled) ----------------------------------------- 45 Sub-location 10 Auto Arm Days (Default = all OFF) ------------------------------------------- 45 Sub-location 11 Auto Disarm Time ----------------------------------------------------------------- 45 Sub-location 12 Auto Disarm Days ----------------------------------------------------------------- 45 Sub-location 13 Auto Arm Delay -------------------------------------------------------------------- 46 Sub-location 14 Reserved ---------------------------------------------------------------------------- 46 Sub-location 15 Reserved ---------------------------------------------------------------------------- 46 Sub-location 16 Duress Reporting Code --------------------------------------------------------- 46 Sub-location 17 Keypad Panic Reporting Code ------------------------------------------------ 46 Sub-location 18 Keypad Fire Reporting Code --------------------------------------------------- 46 Sub-location 19 Keypad Medical Reporting Code --------------------------------------------- 46 Sub-location 20 Keypad Lockout Reporting Code -------------------------------------------- 46 Sub-locations 21 – 44 Partition Programmable Outputs --------------------------------------------- 46 Sub-location 45 Clear Programmable Outputs On Disarming ------------------------------ 47

LOCATIONS 136 – 167 Individual User Code Setup ------------------------------------------------ 48

Sub-location 1 Assigned to Partitions ----------------------------------------------------------- 48 Sub-location 2 User Code Properties ------------------------------------------------------------ 48 Sub-location 3 Close Reporting Code ----------------------------------------------------------- 49 Sub-location 4 Stay Close Reporting Code----------------------------------------------------- 49 Sub-location 5 Open Reporting Code ----------------------------------------------------------- 49 Sub-location 6 Siren Cancel Reporting Code -------------------------------------------------- 49

LOCATIONS 388 – 394 Programmable Output Timing Setup------------------------------------- 49

Sub-location 1 Output Pulse Time ---------------------------------------------------------------- 50 Sub-location 2 Schedule ON Time --------------------------------------------------------------- 50

Page 55

IDS 816 700-283-02I Issued September 2009

Sub-location 3 Schedule ON Days --------------------------------------------------------------- 50 Sub-location 4 Schedule OFF Time -------------------------------------------------------------- 50 Sub-location 5 Schedule OFF Days -------------------------------------------------------------- 50

LOCATIONS 400 – 407 Individual Keypad Setup ----------------------------------------------------- 51

Sub-location 1 Default Keypad Partition (Default = Partition 1) --------------------------- 51 Sub-location 2 Keypad Options ------------------------------------------------------------------- 51

LOCATION 444 Reset Switch Disable (Default = 0) --------------------------------------- 52 LOCATION 445 Installers Code (Default = 9999) ------------------------------------------ 52 LOCATION 446 View Keypad ID ------------------------------------------------------------------ 52

Page 56

IDS 816 700-283-02I Issued September 2009

Index

24 Hour Alarm Zone ......................................................................................................................................... 20

AC Fail / Restore Time ..................................................................................................................................... 25

AC Failure Reporting Code .............................................................................................................................. 28

AC Restoral Code ............................................................................................................................................. 28

Alarm Reporting Code ..................................................................................................................................... 22

Alarm Restoral Reporting Code ....................................................................................................................... 22

Arm/Disarm Zone ............................................................................................................................................. 20

Auto Arm Days .................................................................................................................................................. 45

Auto Arm Delay ................................................................................................................................................. 46

Auto Arm Time .................................................................................................................................................. 45

Auto Disarm Days............................................................................................................................................. 45

Auto Disarm Time ............................................................................................................................................. 45

Auto Test Interval .............................................................................................................................................. 35

Auto Test Reporting Code ............................................................................................................................... 29

Auto Test Time .................................................................................................................................................. 35

Battery Restore Reporting Code ..................................................................................................................... 29

Bitmapped Location ................................................................................................................................... 18, 21

Box Tamper ...................................................................................................................................................... 12

Box Tamper Reporting Code ........................................................................................................................... 29

Bypass Reporting Code ................................................................................................................................... 22

Call-back Phone Number ................................................................................................................................ 42

Clear Programmable Outputs On Disarming ................................................................................................. 47

Close Reporting Code ..................................................................................................................................... 49

Communication Delay ...................................................................................................................................... 34

Communicator Format ..................................................................................................................................... 36

Communicator Options .................................................................................................................................... 34

Contact ID Reporting Codes ........................................................................................................................... 37

Contact ID ......................................................................................................................................................... 37

Cross-zone Count ............................................................................................................................................ 23

Cross-zone Delay Timer ................................................................................................................................... 23

Cross-zoning .................................................................................................................................................... 21

Daylight Saving ................................................................................................................................................. 33

Dedicated Panic Reporting Code ................................................................................................................... 39

Default Keypad Partition .................................................................................................................................. 51

Defaulting Keypads .......................................................................................................................................... 14

Defaulting of the Panel or Master User Code ................................................................................................. 19

Defaulting the Panel ......................................................................................................................................... 13

Device Tamper Reporting Code ...................................................................................................................... 29

Devices (Enrolling) ........................................................................................................................................... 13

Disabled Zone .................................................................................................................................................. 20

Domestic Reporting (Notes) ............................................................................................................................ 37

Doubling ................................................................................................................................ See Zone Doubling

Download Access Reporting Code ................................................................................................................. 29

Download Code ................................................................................................................................................ 15

Page 57

IDS 816 700-283-02I Issued September 2009

Download Options............................................................................................................................................ 41

Downloading Software ..................................................................................................................................... 15

Dual Reporting .................................................................................................................................................. 36

Duress Reporting Code (Explanation) ............................................................................................................ 46

Earth .................................................................................................................................................................. 12

Enabling / Disabling Reporting Groups .......................................................................................................... 37

End-of-Line Resistors ....................................................................................................................................... 10

Engineer Reset (Explanation) .......................................................................................................................... 44

Enrolling Keypads ............................................................................................................................................ 13

Entering Program Mode ................................................................................................................................... 17

Event Driven Programmable Outputs ............................................................................................................. 31

Event Log .......................................................................................................................................................... 13

Exit Delay Period .............................................................................................................................................. 44

Expander Module - Installation ........................................................................................................................ 12

Faulty Keypad ................................................................................................................................................... 14

Fire Detect Output Sequence .......................................................................................................................... 22

Fire Zone ........................................................................................................................................................... 20

Follower Zone ................................................................................................................................................... 20

Follower/Entry Zone ......................................................................................................................................... 20

Force Arm (Explanation) .................................................................................................................................. 43

Force Arm Reporting Code .............................................................................................................................. 22

Function Driven Programmable Outputs ........................................................................................................ 31

Global Options.................................................................................................................................................. 24

Group Reporting Code Enable / Disable ........................................................................................................ 38

Hardware Reset Switch .................................................................................................................................... 13

Hexadecimal Value ........................................................................................................................................... 17

Incorrect Data Entries ....................................................................................................................................... 18

Individual Keypad Setup .................................................................................................................................. 51

Individual User Code Setup ............................................................................................................................. 48

Individual Zone Setup ...................................................................................................................................... 19

Installation ........................................................................................................................................................... 9

Installer Code .................................................................................................................................................... 15

Installer Options ................................................................................................................................................ 52

Installers Code .................................................................................................................................................. 52

Instant Zone ...................................................................................................................................................... 20

Keypad Allocation Problem ............................................................................................................................. 14

Keypad Bus ................................................................................................................................................ 13, 29

Keypad Bus Failure Reporting Code .............................................................................................................. 29

Keypad Fire Reporting Code (Explanation) .................................................................................................... 46

Keypad Lockout Count .................................................................................................................................... 27

Keypad Lockout Reporting Code (Explanation) ............................................................................................. 46

Keypad Lockout Time ...................................................................................................................................... 28

Keypad Medical Reporting Code (Explanation) ............................................................................................. 46

Keypad Options ................................................................................................................................................ 51

Page 58

IDS 816 700-283-02I Issued September 2009

Keypad Panic Reporting Code (Explanation) ................................................................................................. 46

Keypad Setup (Individual)................................................................................................................................ 51

Keypad Sleep Delay ......................................................................................................................................... 28

Keypads (Enrolling) .......................................................................................................................................... 13

Key-switch ......................................................................................................................................................... 12

Lightning Protection ......................................................................................................................................... 12

Location / Zone Defaults .................................................................................................................................. 19

Location Number .............................................................................................................................................. 17

Location Values ................................................................................................................................................ 15

Log ................................................................................................................................................ See Event Log

Low Battery Reporting Code ........................................................................................................................... 29

Mains Failure .................................................................................................................................................... 10

Number of Account Code Digits ..................................................................................................................... 35

Number of Dial Attempts ................................................................................................................................. 35

Number of Rings to Answer ............................................................................................................................. 42

Open Reporting Code ...................................................................................................................................... 49

Outdoor Instant Zone ....................................................................................................................................... 20

Output Pulse Time (Programme Location) ..................................................................................................... 50

Outputs .................................................................................................................. See Programmable Outputs

Panic/Priority Zone ........................................................................................................................................... 20

Partition Arm Options ....................................................................................................................................... 43

Partition Options ............................................................................................................................................... 44

Partition Programmable Outputs ..................................................................................................................... 46

Partition Reporting Codes (Explanation) ......................................................................................................... 46

Partition Setup .................................................................................................................................................. 42

Partition Zone Allocation .................................................................................................................................. 42

Peripheral Devices............................................................................................................................................ 10

Phone Line Restoral Reporting Code.............................................................................................................. 29

Primary Account Code (Partition Setup) ......................................................................................................... 42

Primary Communicator Format ....................................................................................................................... 36

Primary Entry Delay Time ................................................................................................................................. 44

Primary Entry/Exit Zone .................................................................................................................................... 20

Programmable Output Location ...................................................................................................................... 22

Programmable Output Actions ........................................................................................................................ 30

Programmable Output Numbering.................................................................................................................. 30

Programmable Output Options (Programming locations)............................................................................. 49

Programmable Output Timing Setup .............................................................................................................. 49

Programmable Outputs ................................................................................................................................... 12

Programmable Zone Loop Response Time ................................................................................................... 23

Programmable Zone Types ............................................................................................................................. 20

Programming a Bitmapped Location .............................................................................................................. 18

Programming Extended Locations .................................................................................................................. 17

Programming Location Summary ................................................................................................................... 18

Programming Standard Locations .................................................................................................................. 17

Programming Telephone Numbers ................................................................................................................. 40

Programming the Panel ................................................................................................................................... 15

Push to Arm Zone ............................................................................................................................................. 20

Page 59

IDS 816 700-283-02I Issued September 2009

Quick Arm (Explanation) .................................................................................................................................. 43

Radio Transmitter Connection ......................................................................................................................... 13

Remote Control Receiver ................................................................................................................................. 13

Remote Control Unit ......................................................................................................................................... 12

Remote Receiver (IDS) ..................................................................................................................................... 13

Replacement Keypad....................................................................................................................................... 14

Replacing a Faulty Keypad/Device ................................................................................................................. 14

Reporting Groups (Enabling/Disabling) .......................................................................................................... 37

Reporting Options ............................................................................................................................................ 34

Resistors ................................................................................................................................................. 7, 10, 11

Resistors - Colour Codes ................................................................................................................................. 11

RF Jamming Reporting Code .......................................................................................................................... 29

RF Jamming Restore Reporting Code ............................................................................................................ 29

Schedule OFF Days ......................................................................................................................................... 50

Schedule OFF Time ......................................................................................................................................... 50

Schedule ON Days ........................................................................................................................................... 50

Schedule ON Time ........................................................................................................................................... 50

Secondary Account Code (Partition Setup) .................................................................................................... 42

Secondary Communicator Format .................................................................................................................. 36

Secondary Entry Delay ..................................................................................................................................... 45

Secondary Entry/Exit Zone............................................................................................................................... 20

Silent Zone ........................................................................................................................................................ 21

Siren Cancel Reporting Code .......................................................................................................................... 49

Siren Delay ........................................................................................................................................................ 27

Siren Time Out Period ...................................................................................................................................... 27

Siren Toot on Away Arm / Disarm (Explanation) ............................................................................................ 43

Siren Trouble Reporting Code ......................................................................................................................... 29

Stay Close Reporting Code ............................................................................................................................. 49

Stop Report and Control the Alarm Panel....................................................................................................... 36

Sub-location Number ....................................................................................................................................... 17

Swinger Shutdown ........................................................................................................................................... 21

Swinger Shutdown Reporting Code ................................................................................................................ 22

Swinger Shutdown Restore Reporting Code .................................................................................................. 22

System Clock Options ..................................................................................................................................... 32

System Day of Month ....................................................................................................................................... 32

System Day of Week ........................................................................................................................................ 32

System Month ................................................................................................................................................... 32

System Options ................................................................................................................................................ 23

System Programmable Outputs ...................................................................................................................... 30

System Reporting Codes ................................................................................................................................. 28

System Time ..................................................................................................................................................... 32

System Year ...................................................................................................................................................... 32

Tamper by Zone ............................................................................................................................................... 21

Tamper Reporting Code .................................................................................................................................. 22

Tamper Restore Reporting Code .................................................................................................................... 22

Tamper Zone .................................................................................................................................................... 20

Telephone Communicator - Connecting......................................................................................................... 12

Telephone Number Storage Locations ........................................................................................................... 41

Telephone Numbers (Programming) .............................................................................................................. 40

Transformer....................................................................................................................................................... 10

Trouble Display ................................................................................................................................................. 26

Page 60

IDS 816 700-283-02I Issued September 2009

User Code Properties ....................................................................................................................................... 48

User Reporting Codes ..................................................................................................................................... 49

View Keypad ..................................................................................................................................................... 52

Warning Zone ................................................................................................................................................... 20

Wiring .................................................................................................................................................................. 9

Zone Doubling .................................................................................................................................................. 10

Zone Name Editing .......................................................................................................................................... 22

Zone Properties ................................................................................................................................................ 21

Zone Reporting Codes ..................................................................................................................................... 21

Zone Shutdown Count ..................................................................................................................................... 23

Zone Type ......................................................................................................................................................... 19

Page 61

IDS816 User Manual 700-283-01H Issued January 2009

Page 62

IDS816 User Manual 700-283-01H Issued January 2009

Page 63

IDS816 User Manual 700-283-01H Issued January 2009

Quick Reference User Guide

Description

Programming

Add a User Code [*] [Master Code] [*] [0] [*] [New Code] [*]

Change a User Code [*] [Master Code] [*] [2] [*] [Old Code] [*] [New Code] [*]

View a Slot Number

[*] [Master Code] [*] [3] [*] [User Code] [*]

View the Slot number via the zone LED’s

Edit User Code Properties

[*] [Master Code] [*] [4] [*] [User Code] [*] [2,3 or 4] [*]

2 = Duress 3 = Arm to Disarm Code 4 = Global Arm/Disarm Code

Allocate a User Code to a Partition

[*] [Master Code] [*] [5] [*] [User Code] [*] [Partition Number] [*] [#]

Teach a Remote to a User Code

[*] [Master Code] [*] [8] [*] [User Code] [*]

Press Tx Button

Delete a User Code by Code [*] [Master Code] [*] [9] [*] [User Code] [*]

Delete a User Code by Slot Number [*] [Master Code] [*] [10] [*] [Slot Number] [*]

Change Partitions [Mode] [1] [*] [Partition Number] [*]

Select a Stay Profile [Mode] [2] [*] [Profile Number] [*]

Program/Cancel Stay Zone [3] [Zone Number] [*] [#]

Program/Cancel Buzz Zone [4] [Zone Number [*] [#]

Program/Cancel Chime Zone [2] [Zone Number} [*] [#]

Quick Arm [1]

Quick Stay [5]

Stay Arm and Go [6]

Bypassing/Un-bypassing a Zone [9] [Zone Number] [*] [#]

Alarm Memory [0] Displays zones violated.

View Trouble Conditions

[7] 1 = AC Mains Fail 2 = No Communication 3 = Phone Line 4 = Siren Tamper 5 = Low Battery 6 = Loss of Clock Timer 7 = Engineer Reset 8 = Box Tamper 10 = Tamper on Peripheral 11 = Comms. Failure to Peripheral Device 12 = Loss of Power to Peripheral Device

Page 64

IDS816 User Manual 700-283-01H Issued January 2009

IDS 816 Installer Manual

Specifications and Main Features

Frequently Asked Questions

User Manual