iDomotics Starter Kit Quick Installation Manual

QUICK INSTALLATION GUIDE

This product must be installed by a
licensed electrician or other suitably

qualied person.

IMPORTANT NOTE

Please read the following document
carefully before setting up and using your

IDOMOTICS device for the rst time.

4

content

Tools required

Controller

Sensor

Network
cable

Domotic
Central

3 mm athead

screwdriver

Voltage tester
screwdriver

Stripping tool 0,5 or 0,75 mm cable

20 mm hole saw

Power source

7.5 volts

1 ampere

5

central

Connections

USB

Supply

Connect it to the Switch

or to your Router’s LAN port.

Network

cable

RJ-45 input

USB

Optional use
of power
supply.
For the use of
Technical
Personnel.

6

Connection of Light controllers

- Neutral cable inside the light box needed.

- Works with one or two lights.

- T1 corresponds to light 1, T2 to light 2.

Important: Do not connect the keys to the domestic

supply network.

| Connection of Light controllers

Conguration

button

Keys
connection

Electrical
connection

Domestic
network

21

7

Installation of Light controllers

For lament light bulbs, low energy bulbs, LED (110­220V), uorescent tubes, dichroic bulbs (110-220V).

1. Dismantle the frame. If you use the light and tempera-

ture sensor, at least one blind module is required.

2. Identify the return conductor of the lamps and the line

or phase cable, using a voltage tester screwdriver. If you
can’t nd one, add a neutral cable, which will be neces­sary for the performance of the controller.

-OPTIONAL-

3. Take the blind module o the frame and make a

20mm hole in the middle with the holesaw. A power
driver is recommended for this.

4. Disconnect the sensor’s module from the light

switch controller and press it onto the hole of the blind

module. We recommended gluing it in place with silico­ne or multipurpose glue.

Extreme care: handling objects with electrical
voltage! Danger of electrocution!

Proceed only trained electrician or other suitably

qualied person. We recommend placing the
controller next to the light switch.

Installation of Light controllers |

8

5. Cut three cables with a maximum length of 8cm and

connect them to the corresponding terminal board of C,

T1 and T2 of the controller’s keys. It is recommended

that you do not strip the cable more than 5mm with the

cable stripper.

6. Disconnect the returns from the keys of the frame

and connect them to the terminals 1 and 2, and Line and

Neutral to the terminals L and N. Use a 3 mm athead
screwdriver.

N: Neutral cable
L: Line or Phase cable
1: Light return 1
2: Light return 2

See the installation diagram to verify the connections.

7. Connect the cables connected to the frame of the

light switch controller to the keys of the frame, then con­nect the module to the sensors. (See diagram of connec­tion of Light Controller)

C: Common
T1: Light controller 1
T2: Light controller 2

| Installation of Light controller

IMPORTANT. CUT THE ELECTRICITY OF THE RESIDENCE
BEFORE CONTINUING.

9

Introduce it in the metal case inside the wall but DO

NOT close it with the frame. Install the rest of the
controllers before continuing.

8. Connect the electricity of the residence and proceed

to install the central.

9. With the idomotics server installed and congured,

add the corresponding device. ( see page 13 of the User

manual)

Move the handle named ‘CONFIG’ on the light controller
to its opposite side.
Once you can see the ‘identier’ code on the congura­tion of the device, close with (see page 14 of the User

manual)

10. You can now see and operate the controller on the

client app. Proceed to adjust the frame.

Installation of Light controllers |

LAN

Connect it to
the Switch

or Router’s LAN

port.

USB

Optional
connection for

power supply.

CENTRAL’S
BACK

SUPPLY

Connect it to
the plug with the

power source included.

10

Uses: Light Controller

How to connect it to the electric lock.

| Uses of light controller

Doorbell
button

Electrical
connection

Electric lock
which unblocks
the latch

Conguration

button

Domestic
network

11

How to connect it to an air conditioner.

Uses of light controller |

Electrical
connection

Electromagnetic
contactor or
Solid State Relay
(SSR)

Domestic
network

Charge

110/220 V A C control

Conguration

button

- NOTE: if the control uses an SSR, it only shuts o one power pha­se and the other one remains constantly connected to the charge.

12

| Connection of the RGB controller

Connection cables
of LED strip

Connection of the RGB controller

RGB

LED light

G R

12V power
source

12V power
source

Drilling to
adjust the
controller
to the wall

Conguration

button

Drilling to
adjust the
controller
to the wall

Conguration

button

13

Installation of the RGB controller

For LED or monocolor light strips / 12 VDC RGB with
common positive up to 2 A per channel.

1. Take the controller to the place where it will be con-

nected to measure the length of the cable needed, taking

into account the 12V power source cable.

2. Strip the cables which connect the RGB, up to 5mm

with the cable stripper.

3. Proceed to connect the lights.

RGB lights:

+: positive of RGB light
G: colour green
R: colour red
B: colour blue

For monocolor lights:

+: positive of the three lights
G: negative of light 1
R: negative of light 2
B: negative of light 3

*It’s not necessary to connect the three lights.
See the installation diagram to verify the connections.

Installation of the RGB controller |

14

Use a 3mm athead screwdriver.

4. Connect the power source.

Install the rest of the controllers before continuing,

and connect them to terminals 1 and 2, and Line and

Neutral to L and N.

5. Proceed to install the central.

6. Add the corresponding device when the idomotics

server is already installed and congured. (See page 13 ­Conguration manual)

Press the button named ‘CONFIG’ on the RGB controller
once, with a slim item.

Once you can see the ‘Identier’ code on the conguration
of the device, close pressing (See page 14 - Congura-

tion manual)

| Installation of the RGB controller

LAN

Connect it to
the Switch

or Router’s LAN

port.

USB

Optional
connection to

power supply.

CENTRAL’S
BACK

SUPPLY

Connect it to
the plug with the

power source included.

15

7. You can now see and operate the controller on the

Client app.

Proceed to adjust the controller.

Installation of the RGB controller |

Skype: support.idomotics
E-mail: [e-mail]

· To download the manuals:

INSTALLATION

http://www.idomotics.com/download/idomoticsInstalla­tion.pdf

CONFIGURATION

http://www.idomotics.com/download/idomoticsCongura­tion.pdf

· Learn more:

You can nd more information about idomo­tics and its features on:

www.idomotics.com