IDK MULTIMEDIA BC-08 User Manual

1. Fenêtre D'émission
IR Tramsmitter

3. Touches d'appareil
Device keys

5.

Touches numériques (0-9,-/--,11,12)
Number Keys (0-9,-/--,11,12)

7. Touche SETECTION
SET-UP key

9. Touche silencieux
Mute key

11. Touche Programme ­Channel Down

13. Touche Volume ­Volume Down

15. Touches Magnétoscope et Touches Télétexte
Video Recorder keys and Teletext keys

2. Touche TV/AV
TV/AV key

4. Lampe témoin LED
LED Indicator

6. Touche Nicam
Nicam Key

8. Touche POWER
POWER key

10. Touche Programme +
Channel Up

12. Touche Volume +
Volume Up

14. Touche Programme/Canal
Channel/Program key

■ OPERATION INSTRUCTION

Thank you for purchasing the BC-08E universal remote
control. Before you can use your new remote, you will need
to program it to operate the specific A/V home entertainment
equipment you wish to control. Simply enter the proper device
codes for your equipment and it is ready to use.

■ BATTERY INSTALLATION/CHANGE

1. On the back of the BC-08E, open the battery compartment
cover.

2. Insert two (2) AAA new Alkaline batteries.

3. Match the (+) and (-) poles correctly aligned into the
battery compartment.

4. Close the battery compartment.
NOTE : Removing the batteries for more than 2 minutes
will require you to reprogram your remote.

■ SETTING UP BY DIRECT ENTRY

To program your BC-08E to operate your TV :

1. Turn on your TV.

2. Press & hold the SET key and press the TV keyey
once. At this time, the red LED light will light on.

3. Release the SET key and TV key.y.

4. Enter the 3-Digit TV code from the code list for your brand
equipment.
* If you perform this procedure correctly, the red LED light

will go out. Otherwise, the red LED flashes 2 times.

5. Aim the BC-08E at your TV and press POWER key..
Your TV should turn off. If none of the keys or only some
of the keys operate your V, repeat Steps 2-4, trying each
code listed for your brand until you find the one that
operates your TV.

6. Your BC-08E is now programmed to operate your TV. Write
down your TV code on the label at the back of the
BC-08E for future reference.

7. To program other equipment, repeat the Steps 1-6 for
your VCR and or SAT.
NOTE : To leave the SETUP during the code entering,
just press any of the [DEVICE] keys once. Otherwise,
if no code is entered within 10 seconds, the red LED light
will go out automatically.

■ SETTING UP BY AUTO SEARCH

This auto search method checks all its preprogrammed codes
to find the code that will operate your equipment automatically.
This method may take a few minutes.

1. Turn on your TV and press the device mode as TV .

2. Aim the BC-08E at your TV.

3. Press & hold the SET key and POWER key at the
same time for 4 seconds until the red LED light blinks.
Then release the SET key and POWER key.y.
AUTO SEARCH is now performed.

4. If the TV turn off, this indicates that the BC-08E is now
set to your TV.

5. Press any key to exit and the red LED will go out
automatically. The BC-08E is now ready to operate your
TV.

6. To check the code, press POWER to ON position.
Press CH+/-, VOL +/-, , and other applicable keys. If
no function, repeat Steps 1-5.

7. To program other equipment, repeats the Steps 1-6 for
your VCR and or SAT.

■ SETTING UP BY MANUAL SEARCH

This manual search method checks all its preprogrammed
codes to find the code that will operate your equipment. This
method may take a few minutes.

1

1. Turn on your TV.

2. Press & hold the SET key and press the TV keyey
once. At this time, the red LED light will light on.

3. Release the SET key and TV key.y.

4. Press the SET key once again, the red LED light will
flash continuously.

5. Aim the BC-08E at your TV.

6. Now, press & release POWER key until the TV
turns off. This indicates that the BC-08E is now set to
your TV.
HINT : During the Manual Search mode, you can use the
SET key as forward/backward toggle switching to
locate the correct code of your TV in a quick way.

7. Press the [Device] key once. The red LED will go out auto-
matically. The BC-08E is now ready to operate your TV.

8. To check the code, press POWER to ON position.
Press CH+/-, VOL +/-, , and other applicable keys. If
no function, repeat Steps 1-8.

9. To program other equipment, repeat the Steps 1-8 for
your VCR and or SAT.
NOTE 1 : For VCR, press & release either POWER
or key..
NOTE 2 : To leave the MANUAL SEARCH during the code
searching, just press any of the [DEVICE] key once.
Otherwise, if no code is entered within 10 seconds, the
red LED light will go out automatically.

■ PUNCH THROUGH

It allows you to operate TV's VOLUME and function
simultaneously without having to switch the device modes
repeatedly. You can adjust the TV sound source while you
are operating the VCR or Satellite Receiver. Right at your
fingertips.

■ TELETEXT

The function of TELETEXT should operate exactly as your
original remote.

■ PREPROGRAMMED CODE DISPLAY

This method displays its 3-digit preprogrammed codes that
will operate your equipment. You can control the display of
each position in an easy way. For example, press key for
1st digit of code, press key for 2nd digit of code and press
key for 3rd digit of code..

1. Select the desired [DEVICE] key.

2. Press & hold the SET key, then press the desired
digit code you want to display.

3. Release the SET key..

4. The red LED will flash in accord to the count of digit code.
(No flash for digit 0).

5. Repeat Steps 2-4 for next display.

■ TECHNICAL SPECIFICATIONS

Communication Mode : Infrared
Power Requirement : 3V ( 2 x AAA, IEC-LR3,

UM-4 size alkaline batteries)
Effective Range : 7M, ±20 degrees
Max. Operating Temperature : 0˚C to +50˚C
Max. Storage Temperature : -25˚C to +125˚C
Dimension : 63(W) x 28(H) x 173(L) mm
Weight (without batteries) : 56.2g.

2