IDFONE VLP2 User Manual

www.idfone.co.kr

VLP2-2.4GHz

User Manual

CERTIFICATIONS

THIS DEVICE COMPLIES WITH FCC AND IC RULES

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDIGN

INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION OF THE

DEVICE.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY

TO OPERATE THE EQUIPMENT.

Table of Contents

1. Safety Instruction

2. Before You Use

3. Introduction

4. How to use

5. Product Specifications

6. Battery

7. Transmission Functions

8. Troubleshooting

1. Safety Instruction

This instruction is intended to protect user's safety and prevent any damages to the
product. Please read this instruction before use and follow the instruction carefully.

Warning

Failure to comply may cause serious injuries or death

Do not dry this product with electronic heat source such as
radiator, microwave, or stove when it gets wet.

It may lead to explosion, change of shape, or out of order of the
product, and the battery or product changes its color. In this case,
product may not eligible for free services.

Do not use this product in hot and humid conditions out of the
operational range specified. (Recommended operational
temperature: -10℃ ~ 60℃ humidity: 20~85%RH )

When the product is used out of recommended operational environment, it
may lead to explosion or out of order of the product.
Please do not expose the battery under the direct sunlight in a closed area
such as a car. It may explode, change the shape of the product, or become
out of order.

When battery replacement is required, be sure that the parts
replaced are the ones specified by the manufacturer, and not used
for other purposes.

When the battery of different brand is used, durability of the product may be
reduced, or even may possibly lead to explosion. The product will not qualify
for free service under such case. It is strongly recommended to use the
battery referred by the manufacturer.

Keep the product out of children's reach.

It is harmful for the health of children when they play with damaged
battery or put it into the mouth. They may be exposed to harmful
chemical solutions, electromagnetic wave, and/or electric shock.

Do not disassemble, modify, or strike the product.

It may cause the fire.

Safety Instruction 2

Caution

Press the power cord firmly when you plug it in to the outlet, and
use the cord head when you unplug it in order to prevent damage
to the cord.

When the contact is not tight or a part of the cord is cut, it could lead to fire
and/or heat over-generation.
Please do not break the power cord and do not use them when the power
outlet is loose. When the product is wet and/or your hands are wet, do not
touch the outlet and the power cord.

Do not use liquid or aerosol cleaner or chemical solutions such as
alcohol, benzene, or thinner to clean the product.

It could cause fire and damage to the product. Please use dampened
soft cloth for cleaning the product.

Failure to comply may lead to risk of injuries or loss of assets.

Do not place magnetic materials such as credit card, passbook, or
transit passes near the product. You may lose the information contained
on them. Data stored in the product may be damaged or lost.

When you do not use the product, disconnect the power source from
the product and place on safe surface. The product will be damaged if
the product is stricken, beaten, or shaken hard.

Do not paint the product.
It may damage the screen and be a cause of malfunction. In case the
debris from the paint causes allergic reaction, stop using the product
and see the doctor.

Safety Instruction 2

2. Before You Use

Cautions Details

Do NOT open the side
cover.

Do NOT separate the
battery from the unit
during operation.

Please check the
battery capacity.

It may damage VLP2.

If battery is separated from the unit during operation, not
through the proper steps indicated in the User Manual, it
forcefully turns the system off, thus causing troubles in the
system.

If remaining battery life is not sufficient, it may forcefully
turn the system off.

3. Introduction

Portable Voice Transmitter

As portable voice transmitter, it works to transmitting and receiving voice wirelessly.

The transmitter is composed power switch, emergency push button, connection LED,

power alarm LED, etc. Power switch will be used when the transmitter power turns

on and off. The voice will be input via microphone port to connect transmitter .The

emergency push button is transfer the signal with digital under emergency situation

during voice communication. Connection LED shows the transmitter’ display panel

and power alarm LED shows battery short. Transmitting voice is to the remote place

by connecting microphone. And it also informs the status of transmitter by vibration.

Before you use 4

4. How to use

Connection of Power and the way to charge

1. Connect Receiver with a power cable.

2. Turn the power of receiver on.

3. Start the charging after putting the transmitter on the receiver. At this time,

charging LED will be red color..

4. When the charging is completed, the LED of receiver will be green..

How to connect and disconnect

1. Connect the transmitter with the receiver..

2. When LED(Connection) of receiver is blinking 4times, paring between the

transmitter and the receiver will be done..

After pulling out the receiver from transmitter When LED(Connection) turns

into Green color, voice can be transferred to the receiver through

microphone of transmitter.

How to alarm the emergency

1. Push the emergency button of transmitter during connecting transmitter

and receiver..

2. Through EM terminal of Receiver, 12V Voltage will be output and

transmitter will be vibrates continuously.

3. When you are going out from Emergency, push emergency button of

transmitter once again.

4. Then the signal of EM terminal of receiver will be disappear and vibration

of transmitter will stop.

How to show Battery short

Use of Battery

6

When battery of transmitter is short, Battery LED will turn into red color..

How to show the connection of Transmitter.

1. When transmitter and receiver are connected, Green LED will turn on..

2. When the receiver is powered off, Red LED will disappear.

Transmitter Receiver

*Receiver is complied with requirement standard, as a result of test by KOSTEC

Laboratory in accordance with declared by applicant

Use of Battery

7

5. Product Specifications

Description’s Technical Specifications

Equipment Name

Model No

Frequency range

Oscillation type

ITU emission TYPE

Number of channels

Modulation Type

Battery capacity

(Rechargeable)

20dB bandwidth

TX Power(Conducted)

Weight / Dimension

In use time(Talk mode)

Operation temperature

Voice Link Plus

MV-VLP2-2.4TR

2 401.056~2 482.272 MHz

PLL(Phase Local Loop)

1M00F1D

95 Channels

GFSK

3.7Vdc

800 mAh Li-poly

Less than 1 MHz

Max. 100 mW

135 g / 45 mm(W) X 24 mm(D) X 60 mm(H)

3 Hours

-40 ~ + 80 degrees

Belt Clip Type

Power Source

Use of Battery

Typ e

LED

Power On/Off Switch

Internal Antenna

3.7Vdc / 800 mAH (Lithium polymer battery)

ERROR(RED)/TALK(GREEN)

8

6. Battery

The battery doesn’t have to be easy to replace, but do able by someone with moderate

skills. Remove a couple of screws, open up the micro-phone shell and unplug the battery

should be acceptable

[Battery Operation Time]

Capacitance (800mAh)

Continuous Stan-by

Continuous Transmission

[Notes on Battery]

▪ The figures above are measured in the laboratory setting under the actual conditions.

The actual figures in the use of different conditions may vary.

▪ When the duration of operation of battery is reduced to half from the first time of use,

it is required to replace with a new battery.

▪ The battery is discharged even if you do not use it.

80 hours

3 hours

Use of Battery

9

7. Transmission Functions

▪ Transmission Functions Details

► Voice transmit

► Internal microphone and External microphone

► Vibration indicate

► External micro-phone detects and open/short trouble check

► Low battery indicate

► Emergency signal transmit

8. Troubleshooting

Error Messages Possible causes and solutions

The battery is almost empty.

LOW BAT LED(RED)

ERR LED(RED)

▶ Please Docking Charge to Battery.

External microphone is Open or Short

▶Change External microphone

Transmitter was out of range.

SYNC LED(RED Blink)

※ Call for the service if the same trouble appears after following the Troubleshooting.

▶ Transmitter close to Docking Station.

Troubleshooting

10

Thank you

Questions and Warranty inquiry

Give us a call if you have any questions or before visiting our service center.

Customer Service Center

02-2109-6490

Please be sure to use battery charger, battery and peripherals recommended by manufacturer
to prevent damage or breakage to the VLP2.

Warranty period: Battery charger (1 year), Battery (6 months)

Any damage caused by the use of imitation product is liable to the user’s responsibility.