Page 1
User Manual
Page 2
Table of Contents
In the Box ������������������������������������������������������������������������������3
System Requirements �����������������������������������������������������������3
Getting Started ���������������������������������������������������������������������3
Unit Setup �����������������������������������������������������������������������������3
iDevices® Connected App ���������������������������������������������������4
Connecting Your Switch �������������������������������������������������������4
Using The Product ����������������������������������������������������������������5
Problem Solving ��������������������������������������������������������������������5
Factory Reset ������������������������������������������������������������������������5
Light Bar Color Codes ����������������������������������������������������������6
Rating Information ����������������������������������������������������������������6
Regulations ���������������������������������������������������������������������������7
References �����������������������������������������������������������������������������8
Page 3
3
In the Box
Inside your Switch box, you will nd:
• 1 iDevices® Switch
• 1 Quick Start Guide
System Requirements
• iPhone® 4S and later
• iPad® 3rd generation and later
• iPad mini™ and later
• iPod touch® 5th generation and later
• HomeKit™ requires an iPhone, iPad, or iPod touch with
iOS 8.1 or later
• Wi-Fi® 2.4GHz 802.11 b/g/n compatible network
• Router Security Settings Supported: WPA, WPA2, or None
• iDevices® Connected app version 2.0 or higher
Getting Started
Unit Setup
• Remove the Switch from packaging
• Note 8 digit pin located on the back of the unit and on the
Quick Start Guide
• Plug your Switch into a grounded wall outlet
Page 4
4
• The Switch will blink blue indicating it is ready to be set up
on the network
• An accessory (e.g. lamp, fan, etc.) can be plugged in at any time
• Pressing the button on the side of the unit will turn the Switch
on or off
iDevices® Connected App
• Ensure your iOS device’s Wi-Fi® is turned on and is connected to
your home Wi-Fi® Network
• 2.4 GHz b/g/n networks are compatible
• 5 GHz networks are not compatible
• Download the free iDevices Connected app from the App Store
Connecting Your Switch
• Available devices will be shown at the top of the app
• If you don’t see your device, check if the blue setup indicator
on the Switch is blinking fast or slow. If blinking slow, hold
button down for 3 seconds, release, and conrm fast blink.
• In the app, nd the Switch you’d like to connect to and tap
the add icon
• Conrm your home network
• The Switch will turn solid blue to indicate it has successfully joined
your home network
• If this is your rst HomeKit™ product, the app will walk you through
creating a home and a room. If you already have a home set up, the
app will skip this step.
• To ensure the app is adding the correct product, the app will ask
you to conrm its identity. The LED on the Switch will blink purple to
indicate it is the new product being added.
• When prompted, enter the 8 digit pin previously noted on the
Quick Start Guide or back of the Switch. On iOS 9, you can scan
Page 5
5
the pin with your camera, instead of entering it manually
• The app will now walk you through setting up your iDevices Switch
• Once set up, you will be able to quickly control the product within
the app, or using Siri®. To learn about all the additional features,
check out the iDevices Connected app manual for HomeKit™.
Using The Product
• Once the Switch is set up, you can control the color of the LED light
from the Connected app, or choose to turn the LED light off
• Clicking the button on the side of the unit will manually turn the
Switch on or off
Problem Solving
The following information covers some of the most common
troubleshooting issues with the iDevices® Switch. If you’d like more detail
about your Switch and its capabilities, please visit our support site at
iDevicesinc.com/Support, or give us a call at 888.313.7019.
What do I do if an unexpected error occurs during initial setup?
First, try quitting the app by double clicking the home button and sliding
the app upwards. Unplug the Switch from the outlet and plug it back in.
If the LEDs ash green, reopen the app and proceed with the on-screen
instructions. If the LEDs do not ash green, perform a factory reset.
Factory Reset
To reset the Switch to its factory condition, hold down the button for 10
seconds or more, the unit will momentarily ash red, white and then restart
the setup sequence with a fast blue blink.
I’m experiencing issues with the iDevices® Connected app.
The iDevices® Connected app requires iOS 8.1 or greater.
I don’t have a device to pair to my Switch, can I still use it?
You will have the ability to manually turn the Switch on and off using the
button located on the side if no device is present.
Page 6
6
Light Bar Color Codes
MODE DESCRIPTION
Pairing Mode The accessory is waiting for the handset to congure the accessory’s
Wi-Fi®. The LEDs ash blue.
Pairing The accessory is waiting for the handset to initiate and complete pair
set up through either Wi-Fi® or BLE (Bluetooth Low Energy). The LEDs
are solid blue.
Pairing Expired Pairing mode has expired and the accessory is waiting for the user to
press the button for about 3 seconds to reenter pairing mode. The
LEDs slow ash blue.
Pairing Restart To reinitiate the pairing mode, hold the button down for 3 seconds
and the LEDs will rapidly ash blue.
Wi-Fi® Link Up When the accessory joins a Wi-Fi® network, (i.e., the link is up) the
LEDs rapidly ash green for a second.
Wi-Fi® Link Down When the accessory has lost the connection to the Wi-Fi® network,
(i.e., the link is down) the LEDs slow ash orange until the link is up.
Factory Reset To initiate a soft factory reset, which will clear all WiFi and pairing
information, hold the button down for 10 seconds until the LEDs
rapidly ash red. When the button is released the unit will reboot and
reenter the pairing mode.
Identify When the accessory receives a request to identify itself, it rapidly
ashes purple.
Rating Information
UL Rated to UL STD 244A & STD 498A
Listing: E470483
Input: 125VAC, 60 Hz
Output: 125VAC, 60 Hz
Resistive: 1800W (15A)
Tungsten: 600W (5A)
Motor: 1/2HP
For use in dry, indoor locations only.
This product is not to be used by children or persons with reduced
physical, sensory or cognitive capabilities, or lack of experience and
Page 7
7
knowledge, unless they have been given supervision or instruction.
Children should be supervised and instructed not to play with this product.
Regulations
Product Information:
Manufacturer: iDevices® LLC
Model: IDEV0001
FCC ID: 2ABDJ-SWITCH1
IC: 11569A-SWITCH1
FCC Compliance Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Information To The User:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to outlet on a circuit different from that to which
Page 8
8
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement Caution: This transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons.
Canada – Industry Canada (IC)
This device complies with Industry Canada license-exempt RSS Standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence
standard RSS (s). Son fonctionnement est soumis aux deux conditions
suivantes:
(1) Cet appareil ne doit pas provoquer d’interférences et (2) cet appareil
doit accepter toute interference, y compris celles pouvant causer un
mauvais fonctionnement de l’appereil.
IC RF Radiation Exposure Statement Caution: This transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons.
Cet équipement est conforme aux limites d’exposition aux rayonnements
IC établies pour un environnement non controlé. Cet équipmement doit
etre installé et utilisé avec un minimum de 20 cm de distance entre la
source de rayonnement et votre corps.
References
Requires the iDevices® Connected app.
For warranty information please visit iDevicesinc.com/warranty
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries. App store is a service mark
of Apple Inc. HomeKit is a trademark of Apple Inc.
Loading...