Identive Cloud 4701F – Operation Manual
Operation Manual for Cloud 4701F
Version 0.4
Version: 0.4 Page 1 of 5
Identive Cloud 4701F – Operation Manual
Version
Date
Description of Change
Author
0.0
26-Nov-13
Initial version
Sudhan
0.1
26-Nov-2013
Document updated after reviews
Sudhan
0.2
16-Jan-2014
FCC statement updated
Sudhan
0.3
17-Jan-2014
Block diagram removed and confidential
declaration removed
Sudhan
0.4
17-Jan-2014
Operational description and functional
description separated into 2 documents
Sudhan
Document History
Version: 0.4 Page 2 of 5
Identive Cloud 4701F – Operation Manual
Table of Contents
1 Scope of the document ....................................................................................................... 4
2 About the reader.................................................................................................................. 4
3 Operating conditions ........................................................................................................... 4
4 Driver Installation in Windows ............................................................................................. 4
5 Communication with a card ................................................................................................. 4
6 Certification - FCC ............................................................................................................... 4
7 Certification – CE ................................................................................................................ 5
Version: 0.4 Page 3 of 5
Identive Cloud 4701F – Operation Manual
1 Scope of the document
The document provides the Operational description of Cloud 4701F reader.
2 About the reader
Identive Cloud 4701F is a USB based dual interface reader capable of reading ISO7816
Contact smart cards and ISO14443 Contactless cards. The reader connects to a host PC via USB2.0
Full speed interface.
3 Operating conditions
Operating temperature : -20 to 70 C
Storage temperature : -25 to 85 C
Humidity : 95%RH
4 Driver Installation in Windows
Follow the sequence of steps to install the driver
Plug in the reader to a Windows PC
The PC prompts for a driver
Select Microsoft CCID driver and install the driver
After the driver installation, the reader is ready for use
5 Communication with a card
Follow the sequence of steps to communicate with the contact card,
Plug in the reader to a Windows PC and load the driver
Launch the PCSCDIAG Utility
Insert the contact card into the card slot of the reader
Check the ATR of the card being displayed in the PCSCDIAG Utility
Follow the sequence of steps to communicate with the contactless card,
Plug in the reader to a Windows PC and load the driver
Launch the PCSCDIAG utility
Place a contactless card on top of the reader
Check the ATR of the card being displayed
6 Certification - FCC
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
Version: 0.4 Page 4 of 5
Identive Cloud 4701F – Operation Manual
and can radiate radio frequency energy and, if not installed and used in accordance with the
manufacturer’s instructions, may cause interference harmful to radio communications. However, there
is no guarantee, however, that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
Information to user
Changes or modifications not expressly approved by Identive could void the user’s authority
to operate this equipment.
7 Certification – CE
Identive hereby declares that the Identive CLOUD 4701F devices mentioned herein are in
compliance with the essential requirements and other relevant portions of the Directive R&TTE.
Version: 0.4 Page 5 of 5
Loading...