Identec Solutions ILR IB350LCC User Manual

IDENTEC SOLUTIONS

i-B350L -CC

HARDWARE USER MANUAL

i-B350L -CC – Hardware User Manual | 20. September 2019

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.

2

Proprietary Notice

This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or
disclosed to other parties in whole or in part without the prior written authorization from IDENTEC SOLUTIONS.

Disclaimer and Limitation of Liability

IDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents do not make
any express or implied warranties or representations with respect to such information including, without limitation,
warranties as to non-infringement, reliability, suitability for a particular purpose and accuracy. IDENTEC
SOLUTIONS shall not under any circumstances be liable to any person for any special, incidental, indirect or
consequential damages, including without limitation, damages resulting from use of or reliance on information
presented herein, or loss of profits or revenues or costs of replacement goods, even if informed in advance of the
possibility of such damages.

Trademarks

“IDENTEC SOLUTIONS”, “Intelligent Long Range”, “ILR” and the stylized “i” are registered trademarks.
“i-PORT” and “Visibility Delivered.” are trademarks of IDENTEC SOLUTIONS, Inc. and/or IDENTEC SOLUTIONS

AG.

Copyright Notice

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.
No part of this document may be reproduced or transmitted in any form by any means, photographic, electronic,

mechanical or otherwise, or used in any information storage and retrieval system, without the prior written
permission of IDENTEC SOLUTIONS.

Issue 3.0 / September 2019 (MOM)

Subject to alteration without prior notice.
Copyright © 2019 IDENTEC SOLUTIONS AG

Printed in Austria

i-B350L -CC – Hardware User Manual | 20. September 2019

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.

3

Radio Frequency Compliance Statement

IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices:

MODEL:

i-B350L CC

Region/Country

Organization

Marking

EUROPE:

EU

CE

USA:

FCC

FCC ID: OO4-ILR-IB350LCC

CANADA:

Industry Canada

3538A-IB350LS

The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by
IDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTEC
SOLUTIONS, or unauthorized changes to approved products, may void the compliance of these products and result in
the loss of the user(s) authority to operate the equipment.

European Notification According R&TTE Directive

This equipment complies to Art. 6.4 of R&TTE Directive (2014/35/EU, 2014/30/EU, 99/5/EC [expires on June, 12th
2016] and 2014/53/EU [valid from June, 13th 2016]). It is tested for compliance with the following standards: EN 300
220-1, ETSI EN 300 220-2, ETSI EN 301 489-1, ETSI EN 301 489-3, EN 60950-1:2006 + A11:2009 + A1:2010 +
A12:2011

USA Notification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired

operation.

CAUTION TO USERS

Changes or modifications not expressly approved by the party responsible for
compliance could void the user`s authority to operate the equipment.

Class B: (Section 15.105) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or
relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an
experienced radio/ TV technician for help. (Section 15.21) CAUTION: Any changes or modifications not expressly
approved by the grantee of this device could void the user's authority to operate the equipment.

Canada Certification

This device complies with Industry Canada’s license exempt RSS’s. Operation is subject to the following two

conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence.
L‘exploitation est autorisée aux deux conditions suivantes:
(1) l‘appareil ne doit pas produire de brouillage, et
(2) l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d‘en compromettre le fonctionnement.

i-B350L -CC – Hardware User Manual | 20. September 2019

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.

4

WARNING - This product should be installed by personnel trained in installation of
equipment in industrial environments and meet the representative country’s
National Electrical Code.

Electrostatic Discharge

This product contains components that are sensitive to electrostatic discharges. Please observe
the special instructions for their protection. Incorrect handling can damage the unit and cause
the invalidation of the warranty.

Minimum safety precautions against electrostatic discharge:

 Establish earth contact before you touch the unit. (For example, touch the earthing screw on the unit.) Best

practice is to use an antistatic ribbon and earth yourself permanently for the time you handle the unit.

 Avoid unnecessary contact with the unit connectors and assemblies inside the unit.
 Only open the unit if the operational settings (as described in the manual) expressly requires it.
 Use antistatic tools for the setting of the unit. (Warning: Do not touch life-threatening voltages with these tools).
 Do not store unit and components without protective packaging.
 Remove unit and components from the packaging only prior to installation.

These notes are not sufficient to guarantee complete protection from electrostatic discharges! We
recommend the use of suitable protective equipment.

IDENTEC SOLUTIONS does not accept the return of products where the regulations concerning the ESD
precautions and protective packaging materials were not followed.

i-B350L -CC – Hardware User Manual | 20. September 2019

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.

5

Safety Instructions

The system described in this manual is for exclusive operation of trained employees. Only qualified personnel that
have knowledge of the potential dangers involved should perform the installation, settings, maintenance and repair
of the units used.

Operational Safety

The correct and safe use of these systems assumes that operating and service personnel follow the safety
measures described in the manual alongside the generally acceptable safety procedures.

If there is a possibility that safe operations cannot be guaranteed, the system must be switched off, secured against
accidental use and the service unit responsible immediately informed.

Safety Documents

The i-B350L CC was designed, tested and supplied in perfect condition according to document IEC/EN 60950-1
Safety Requirements.

Condensate / Change of Temperature

To avoid condensation in the system, the unit must be allowed to slowly adjust itself to warmer temperatures after
removal from cold and cool environments.

Connections / Power Supply

The supply circuits must comply with the conditions set out for the SELV circuits (see EN 60950-1).
During maintenance damage could occur if printed circuit boards or cables are connected or disconnected whilst

the power supply is still on. Therefore, only work on the connection and the components when they are not live.

Battery Inside

All system tags contain a battery; therefore, the following warning should be heeded:

WARNING - Fire, explosion and burn hazard risk of explosion if battery is replaced by an
incorrect type. Do not recharge, short circuit, crush, disassemble, heat above 100 °C (212 °F).
Do not incinerate, or expose contents to water

Spare Parts

We recommend that only personnel, original products, spare and replacement parts authorized by IDENTEC
SOLUTIONS be used for installation, service and repair. IDENTEC SOLUTIONS does not accept any responsibility
for materials used, work carried out or possible consequences from unauthorized third party vendors.

Glossary

 SELV Safety Extra Low Voltage – Protective measure against dangerous body currents. Protective first voltage, circuit not floating.