IDENTEC SOLUTIONS i-B350 S, i-B350L S Installation And Operation Manual

ILR 350 Series

i-B350L S

Installation and Operation Manual

(preliminary)

VISIBILITY DELIVERED. PAGE 2 OF 15

Proprietary Notice

This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or
disclosed to other parties in whole or in part without prior written authorization from IDENTEC SOLUTIONS.

Disclaimer and Limitation of Liability

IDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents do not make
any express or implied warranties or representations with respect to such information including, without
limitation, warranties as to non-infringement, reliability, suitability for a particular purpose and accuracy.
IDENTEC SOLUTIONS shall not under any circumstances be liable to any person for any special, incidental,
indirect or consequential damages, including without limitation, damages resulting from use of or reliance on
information presented herein, or loss of profits or revenues or costs of replacement goods, even if informed in
advance of the possibility of such damages.

Trademarks

―IDENTEC SOLUTIONS‖, ―Intelligent Long Range‖, ―ILR‖ and the stylized ―i‖ are registered trademarks and
―i-Q‖, ―i-D‖, ―i-B‖, ―i-CARD‖, ―i-PORT‖, ―i-LINKS‖, ―Visibility Delivered‖ are trademarks of IDENTEC

SOLUTIONS, Inc. and/or IDENTEC SOLUTIONS AG.

Copyright Notice

Copyright © 2011 IDENTEC SOLUTIONS. All rights reserved.
No part of this document may be reproduced or transmitted in any form by any means, photographic,
electronic, mechanical or otherwise, or used in any information storage and retrieval system, without the prior
written permission of IDENTEC SOLUTIONS.

Issue 1 / August 2011
– 29. September 2011 –

IDENTEC SOLUTIONS AG,
Millennium Park 2, 6890 Lustenau, Austria

Phone: [phone], Fax: [phone]
E-Mail: [e-mail]
www.identecsolutions.com

Subject to alteration without prior notice.
© Copyright IDENTEC SOLUTIONS 2010

VISIBILITY DELIVERED. PAGE 3 OF 15

IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices:

MODELS:

i-B350 S, i-B350L S

Region/Country

Organization

Marking

EUROPE:

EC

CE

USA

FCC

FFC ID OO4-ILR-IB350LS

Canada

Industry Canada

IC: 3538A-IB350LS

European Notification according R&TTE Directive

This equipment complies to Art. 6.4 of R&TTE Directive (1999/5/EC). It is tested for compliance with the
following standards: ETSI EN 300 220, ETSI EN 301 489, EN 60950

USA Notification

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by
IDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTEC
SOLUTIONS, or any changes or modifications not expressly approved by the party responsible for compliance
could void the users’ authority to operate the equipment.

The device has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.

VISIBILITY DELIVERED. PAGE 4 OF 15

Contents

1 INTRODUCTION ................................................... .

1.1 PREPARATIONS ........................................................ .

1.2 RECOMMENDED PROCEDURE ....................................... .

1.3 SCOPE OF THIS DOCUMENT ......................................... .

1.4 RESPONSIBILITY ...................................................... .

1.5 ASSOCIATED DOCUMENTS .......................................... .

1.6 SCOPE OF DELIVERY—VISUAL INSPECTION ..................... .

2 SAFETY PRECAUTIONS ........................................ .

3 TAG MOUNTING TECHNIQUES ..................................................................................... 5

3.1 DIMENSIONAL DRAWING ................................................................................................... 8

3.2 CABLE STRAPS ................................................................................................................ 8

3.3 RIVETS ......................................................................................................................... 9

3.4 SCREWS ..................................................................................................................... 10

4 INITIAL OPERATION, CONFIGURATION OF THE TAG

4.1 GENERAL ............................................................... .

4.2 PING RATE ............................................................. .

4.3 BURSTS WHEN PASSING A POSITION MARKER .................. .

4.4 LIMITATIONS OF THE USER DATA FIELD ......................... .

4.5 INFORMATION ON BURST SETTINGS .............................. .

5 MAINTENANCE .................................................... .

5.1 GENERAL ............................................................... .

5.2 REGULAR CLEANING OF THE SURFACE ........................... .

5.3 PRECAUTIONARY MAINTENANCE ................................... .

5.4 RETURNS ............................................................... .

6 TECHNICAL DATA ....................................................................................................... 14

VISIBILITY DELIVERED. PAGE 5 OF 15

1 Introduction

1.1 Preparations

This installation manual must be read carefully prior to starting the installation. The described installation
works assume that installation materials like cable, antenna, tag holder, etc. are available.

1.2 Recommended Procedure

1. Check the Scope of Delivery according to the Bill of Delivery

2. Read this manual completely

3. Do the initial operation for every single tag

4. Mount the tags

5. An additional performance check of the tags and a system test can now be done

1.3 Scope of this Document

This document is the users’ manual of the models i-B350 S and i-B350L S.
This document is intended only for mechanical installation rsp. everyday use.

1.4 Responsibility

IDENTEC SOLUTIONS is not responsible for any errors occurring in this document.

1.5 Associated Documents

 i-B350L W — ILR350 Wristband Tag Datasheet

1.6 Scope of Delivery—Visual Inspection

Check delivery whether it is complete and for any damages. If the delivery is not complete or damaged
immediately inform the carrier. The dispatch and service organization of IDENTEC SOLUTIONS should also be
informed to facilitate the repair or exchange of the system.