IDEM SAFETY SWITCHES ES-P, ES-SS(P), ESL-SS, ESL-SS(P), ES-SS Operating Instructions Manual

Emergency Stop Switches

Standards:

IEC 60947-5-5 UL508

EN

ISO 13850

Case Material

Stainless Steel 316 or Plastic

Safety Contact type

IEC 60947

-5-

1 Double break Type Zb

Contact Material

Silver

Termination

Clamp up to 2.5 sq. mm conductors

Rating Utilisation Ca

tegory : AC15

Operational Rating

AC15 A300 240V. 3A /120V 6A. ac

Thermal Current (Ith)

10A.

Rated Insulation Voltage (Ui)

500V.

Withstand Voltage (Uimp)

2500V.

Short Circuit Overload Protection

Fuse Externally 10A. (FF)

Operating

Temperature

-25C / 80C.

Enclosure Protection

IP67 Plastic or IP69K Stainless Steel

(NEMA 6)

Optional Explosion Proof Contact Block:

Classification

Rated Voltage
Rated Current

Safety Classification and Reliability Data:

Mechanical Reliability B10d

ISO 13849-1

EN 62061

Safety Data - Annual Usage

PFHd

Proof Test Interval (Life

)

MTTFd

Ex d IIC T6 (-20C Ta 60C) Gb
Ex tb IIIC T85C (-20C Ta 60C) Db
250V ac/dc
2 pole 4A. 4 pole 2.5A.

1.5 x 106 operations at 100mA load
up to PLe depending upon system architecture
up to SIL3 depending upon system architecture
8 cycles per hour / 24 hours per day / 365 days
<1.0 x 10

-7

21 years
214 years

IMPORTANT NOTE:

Read and understand these instructions before installing, operating, or maintaining this equipment.

The product is designed to be a component of a customised safety orientated control system. It is the responsibility of each manufacturer to ensure the correct overall functionality of its
systems and machines. IDEM, its subsidiaries and affiliates, are not in a position to guarantee all of the characteristics of a given system or product not designed by IDEM.

Application:

Emergency Stop Switches are mounted on machines and sections of plant conveyors that cannot be protected by guards.
In combination with any dual channel safety monitoring controllers these switches can be used as emergency stop devices and monitored for up to Category 4/PLe to ISO13849-1.

Operation:

All Emergency Stop Switches conform to European Standard EN ISO 13850 and IEC 60947-5-5. They have a positive mechanical linkage between the switch contacts and the
E-Stop Button. The switches are mechanically latched and can then only be returned to the operational condition by a pressing the reset button as required by EN ISO 13850
and IEC 60947-5-5.

Installation Guide:

1. Installation of all switches must be in accordance with a risk assessment for the individual application and in accordance with local wiring regulations and EN60204-1.
Installation must only be carried out by competent personnel and in accordance with these instructions.

2. M4 mounting bolts must be used to fix the switches. Tightening torque for mounting bolts to ensure reliable fixing is 4 Nm. Tightening torque for the lid screws, conduit entry plugs and
cable glands must be 1.5 Nm to ensure IP seal. Only use the correct size gland for the conduit entry and cable outside diameter.

3. Check operation of all switches and the control circuits by activating the switch (depress the Red Button) and resetting each switch by twisting the Red Button. Ensure each time that
the switches latch off and require manual resetting.

4. For versions with the Protection Shroud ensure that the padlock size is suitable to prevent re-setting of the button.

Maintenance:

Every Week: Check correct operation of the control circuits and latching mechanism.
Inspect for damage to the E Stop button or casing.
Every 6 Months: Isolate power and remove cover. Check screw terminal tightness and
check for signs of moisture ingress. Never attempt to repair any switch.

Operating

Instructions

Type ES

-

P (Plastic)

Knock –out for
plastic version

Type ES

-SS

(Stainless Steel)

Mirror Polished Finish

Type ES

-

SS(P)

(Stainless Steel)

With button protection

shroud with padlock

holes for lock off during

maintenance

Type ES

L-SS

(Stainless Steel)

Type ES

L-SS(P)

(Stainless Steel)

With button protection

shroud with padlock

holes for lock off during

maintenance

Type ES

L-SS(L)

(Stainless Steel)

With 2-colour LED

LED Wiring ex

amples (if fitted):

Black (or Terminal 2) is 0V (or Neutral for 110V and 230V ac versions).
When power is applied to the Red wire (or Terminal 1), the LED will illuminate Red.
When power is applied to the Green wire (or Terminal 3), the LED will illuminate Green.

LED has 2 colours

Recommended Colour Usage:

Flashing or Steady Red – Stopped
LED Steady Green - Run

Terminal 2 or Black

Terminal 1 or Red

Terminal 3 or Green

Wiring circuits for Explosion Proof Versions:

1 NC 1 NO

2 NC 2 NO

2 NC

INFORMATION WITH REGARD TO UL508:

Type 1 Enclosure
Contact Blocks A300 230V/3A 120V/6A
Wire range: 16AWG – 12AWG Copper Torque 7lb/in (0.8Nm)
LED powered by LVLC or Class 2 only.

Type ES

L-SS(LP)

(Stainless Steel)

With 2-colour LED and

button protection

shroud with padlock

holes for lock off during

maintenance

Emergency Stop Switches

SPECIAL NOTE:

Where required by local regulations
please affix the supplied yellow
“EMERGENCY STOP” sticker as
shown in the image.

SPECIAL NOTE:

Where the Risk Assessment identifies that inadvertent operation of the E-Stop button
may occur during use or breakage and loss of the button function is foreseen, it may
be preferable to specify the protection shroud version. If the Risk Assessment for the
particular application allows use of the protection shroud, it is recommended
consideration be given to the conditions of operation of the button during spontaneous
operation as the shroud is not suitable for traditional E-Stop palm actuation of the
button. The Risk Assessment must clearly identify any restrictions to the proper use of
the button including any training or the requirement to place any restriction notices at
the E-Stop location (e.g. “FINGER OPERATION REQUIRED”).

Doc: 102531

Jan. 2016

IDEM SAFETY SWITCHES Ltd., 2 Ormside Close, Hindley Industrial Estate, Hindley Green, Wigan, WN2 4HR UK. Tel: +44 (0)194

2 257070 Fax.: [phone]

IDEM (USA)

4416 Technology Drive

, Fremont, CA 94538 Tel:510

-

445-0751 Fax:1866

-

431-7064

email:

[e-mail]

Web:

www.idemsafety.com

DIMENSIONS: ES-P

DIMENSIONS:

ES-SS

ES-SS(P)

DIMENSIONS:

ESL-SS

ESL-SS(P)
ESL-SS(L)
ESL-SS(LP)