Idem MPC, MMC, SMC, SPC, WMC Operating Instructions Manual

Non Contact Coded Safety Switches

IMPORTANT NOTE

:

WMC LPC LMC

CMC

Misalignment range

Operating Instructions

MPC

LPC

WPC

SPC

CPC

RPC

RMC

MMC

(PLASTIC)

(METAL)

SMC

(PLASTIC)

(METAL)

WMC

(PLASTIC)

(METAL)

(PLASTIC)

LMC

(METAL)

CMC

(PLASTIC)

(METAL)

RMC

(PLASTIC)

(METAL)

Read and understand these instructions before installing, operating, or maintaining this equipment.
The product is designed to be a component of a customised safety orientated control system. It is the responsibility of each manufacturer to ensure the correct overall functionality of its
systems and machines. IDEM, its subsidiaries and affiliates, are not in a position to guarantee all of the characteristics of a given system or product not designed by IDEM.

APPLICATION:

Coded Non Contact switches are designed to interlock hinged, sliding or removal guard doors. They are specifically advantageous when:

a) poor guard alignment exists
b) anti-tamper is required
c) high hygiene requirements exist e.g. food industry hose down
d) a long mechanical life is required (no moving or touching parts).

When used in combination with a Dual Channel Safety Relay, Coded Non Contact Switches can be used to provide protection up to Category 4 and Ple to ISO13849-1.

OPERATION:

All Coded Non Contact Safety Switches are designed to conform to IEC 60947-5-3 and be used as directed by EN1088, EN ISO12100 and EN 60204-1. They have coded magnetic
sensing which provides a wide (>10mm) sensing distance and provides a high tolerance to misalignment after sensing. They can be fitted behind stainless steel fittings and can operate in
extreme environments of temperature and moisture.

INSTALLATION:

Installation of all Coded Non Contact Switches must be in accordance with a risk assessment for the individual application.
The use of a Safety Relay is required for monitoring Coded switches. These relays monitor 2 redundant circuits as per ISO13849-1 for up to Ple / Category 4 protection.
Coded Non Contact switches are designed to operate with most Dual Channel Safety Relays to satisfy IEC 60947-5-3 PDF-S.
M4 mounting bolts must be used to fix the switches. (Except RPC and RMC types.) RPC and RMC types require fitting through 30.5mm clearance holes. The lock nuts supplied must be
used to secure the switches. Tightening torque for mounting bolts to ensure reliable fixing is 1.0 Nm. Always mount on to Non Ferrous materials. The recommended setting gap is 5mm.
The Safety switch must not be used as a mechanical stop or be adjusted by striking with a hammer. The actuator must not be allowed to strike the switch. Do not mount adjacent switches
or actuators closer than 30mm.
Typical misalignment tolerance after setting is 5mm.
After installation always check each switch function by opening and closing each guard individually in turn and ensuring that the Green LED on the switch and the LED’s on the Safety
Relay are illuminated when the switch is closed and are extinguished when the switch is open. Check that the machine stops and cannot be re-started when each switch is open.
For MPC types, fit the protective screw covers after the final checks have been completed.

ACTUATOR OPENING DIRECTIONS:

Align actuator and switch using the target lines.

MPC MMC SPC SMC WPC

RPC

MAINTENANCE:

Monthly: Check alignment of actuator and look for signs of mechanical damage to the switch casing. Check wiring for signs of damage.
Check each switch function by opening and closing each guard individually in turn and ensuring that the Green LED on the switch and the appropriate LED’s on the Safety Relay are

illuminated when the switch is closed and are extinguished when the switch is open. Check that the machine stops and cannot be re-started when each switch is open.
Never repair any switch, actuator or integral cables. Replace any switch displaying signs of mechanical damage to the casing or cables.

CPC

Non Contact Coded Safety Switches

IDEM (USA) 4075 Papazian Way, Suite 105, Fremont, CA 94538 Tel:510

-

445-0751 Fax:1866

-

431-7064 email:

[e-mail]

Web:

www.idemsafety.com

Quick Connect (QC)

Flying Lead

Circuit

Output Types

8 Orange Auxiliary (NO)

5 Brown Auxiliary (NO)

4 Yellow

NC 2 +ve

6 Green NC 2 -ve

7 Black

NC 1 +ve

1 White NC 1 -ve

2 Red Supply +24Vdc

3 Blue Supply 0 Vdc

Safety Classification and Reliability Data:

Minimum switched current

10V. dc 1mA

Dielectric withstand

250V.ac

Insulation Resistance

100 Mohms

Recommended setting gap

5mm

Switching Distance

Sao 10mm Close

(RMC 8mm C

lose)

Tolerance to misalignment

5mm in any direction from 5mm setting gap

Switching frequency

1.0 Hz maximum

Approach speed

200mm/m. to 1000mm/s.

Body Material

MPC SPC

WMC LPC CPC

RPC Polyester

MMC

SMC WMC LMC CMC RMC S/Steel 316

Temperature Range

–25/80C Polyester

–

25/105C S/Steel 316

Enclosure Protection

IP67 (Plastic) IP69K (S/Steel 316)

Shock Resistance

IEC 68-2-27 11ms 30g

Vibration Resistance

IEC 68-2-6

10-

55 Hz. 1mm

Cable Type

PVC 6 or 8 core 6mm O.D.

Mounting Bolts

2 x M4 Tightening torque 1.0 Nm

Mounting Position

Any

Single switch to SCR2/3

Multiple switches in series to SCR2/3 Safety Relay

SPC SMC

SMC-F

MPC MMC

Doc: 10250

5

Information with regard to UL 508:

90ºC Stainless Steel

SMC-F Rear Fixing Version has

CMC-F Rear Fixing Version has

CPC CMC CMC-F

two x M4 x 10 tapped holes at rear

two x M4 x 10 tapped holes at rear

LPC LMC

RPC RMC

Safety Relay

WPC WMC

M12 8 way
Male Plug
(Pin view from switch)

Switching Reliability

EN 954-1

ISO 13849-1

EN 62061

Safety Data – Annual Usage

PFHd

Proof Test Interval (Life)

MTTFd

Standards:

Colours

(Actuator present)

200mA Max. 24Vdc

200mA Max. 24Vdc

200mA Max. 24Vdc

+ 10% -15%
USE SELV / PELV

3.3 x 106 operations at 100mA load
Up to Category 4 with Safety Relay
Up to PLe depending upon system architecture
Up to SIL3 depending upon system architecture
8 cycles per hour/24 hours per day/365 days

2.52 x 10-8
47 years
470 years
EN1088 IEC 60947-5-3 EN 60204-1
ISO 13849-1 EN62061 UL508

Sar 20mm Open (RMC 12mm Open)

Solid State

For all IDEM switches the NC circuits are closed
when the guard is closed and the actuator present.

Type 1 Enclosures.
Control No: 48W5.
Max.Temp: 70ºC Plastic version.

IDEM SAFETY SWITCHES Ltd., 2 Ormside Close, Hindley Industrial Estate, Hindley Green, Wigan, WN2 4HR UK. Tel: [phone] Fax.: [phone]

June. 2014