IDEM L1R User Manual
PATNEON COOL GRAY 10
PATNEON 376
DIELINE
75mm 75mm 75mm 75mm 75mm
156mm
1R
USB Charging Cable
Saddle & Seat Post
Bracket
Taillight
Remote Control &
Bracket
ChargeIn the box
Connect Taillight to your computer or external power bank
with cable provided.
(Optional)
or
When Taillight is charging, the light will turn on. When it is
fully charged, the light will turn off.
Remote
LOCK
Press “LOCK” button once, Taillight will sound
an ALERT 3 times. Taillight is now armed and
you will hear another ALERT sound after 3
seconds. If distrubed afterwards, the alarm will
sound.
Remote
UNLOCK
Press “UNLOCK” button once and a single long
ALERT will sound. This signals the exit of
“LOCK” mode.
Wireless / Multifunction
Bicycle Taillight
Quick Start Guide
Help & Warranty
?
Help:
For more information and support on this product, please
visit our website.
www.ideminc.com/support
Warranty:
This product is covered by a warranty for a period of one
(1) year from the date of original purchase. For more
information, please visit our product website.
Hearing Damage:
!
CAUTION
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a
class B digital device,pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequence energy and,if
not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that
interference will not accor in a particular installation.if this equipmemt does
cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on,the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which
the receiver is connectec.
• Consult the dealer or an experienced radio/TV technician for help.
FCC-ID: 2AMVD-L1R
Do not place ringing
alarm or activate alarm
near ears.
(1x) LG Hex Bolt
(1x) MED Hex Bolt
(2x) SM Hex Bolt
(1x) Adhesive Pad (2x) Zip Ties
(1x) LG Hex Tool
(1x) SM Hex Tool
Taillight Operation
Red Button
Press to cycle through different “Flash” modes (same
function as remote FLASH button).
Mode Pattern Flash/Sec.
1
2
3
4
Burst Flash
Fast Flash
Slow Flash
Taillight is off
3
2
1
0
2sec.
Blue Button
When there is a malfunction between Taillight and
remote control, press for 2 seconds and Taillight will
sound an ALERT. Press any key on the remote control,
and Taillight will sound an ALERT 2 times confirming the
completion of pairing.
When the remote control is lost, contact customer
support.
“PUSH!”
Press the release
hook and remove
the remote control
to access remote
buttons.
Taillight Installation
OPTION 1: Saddle Mount
Slide open saddle mounting bracket.
1
Position bracket under bike saddle.
2
Brackets may also be installed upside down.
Tighten bracket with supplied LG Hex Bolt and
3
LG Hex Tool.
Slide Taillight onto mounting bracket. Secure
4
Taillight to the bracket with a supplied SM Hex Bolt
and SM Hex Tool.
“Click!”
TRIGGER ALERT
When in “LOCK” mode and motion is detected,
Taillight will generate a loud ALARM briefly. If
motion is detected again within the next 10
seconds, an ALARM will sound nonstop for 30
seconds, and then return to “LOCK” mode.
21
3 4
Taillight Installation
OPTION 2: Seat Post Mount
Secure seat post mounting bracket with supplied
1
MED Hex Bolt and LG Hex Tool.
Slide Taillight onto mounting bracket. Secure
2
Taillight to the bracket with a supplied SM Hex Bolt
and SM Hex Tool.
“Click!”
HORN
Press and release
“HORN” button to receive
3 short horn tones. Press
and hold the button to
receive 3 short and a long
horn tones.
Remote Installation
Handle Bar Mount
Attach adhesive pad to the bottom of mounting
1
bracket.
Insert cable ties through the mounting bracket.
2
Place the bracket with adhesive pad over the handle
3
bar. Pull cable ties tightly to secure the remote in
place. Trim excessive cable ties if needed.
FLASH
When Taillight is not in
“LOCK” mode, press
“FLASH” button to cycle
through each of the
“FLASH” Modes.
“Pull & Tighten!”
© 2017 IDEM, Inc.
All resgistered logos and trademarks property of the respective owners.
8
5
7
6
Loading...