IDEC TW Series Accessories Catalog
Oiltight Switches & Pilot Devices
ø22mm - TW Series
Accessories
TW Series Accessories
Appearance Description/Usage Part Number
Lamp Removal Tool
Contact Block Remover
Nut Locking Wrench Used in OR-14 locking wrench to tighten locking nuts inside square bezel TW-KQ2
Metal Bezel
Plastic Bezel
Boot/Cover
Rubber tool used to install or remove LED’s and incandescent lamps OR-55
Used to remove contact blocks, transformers, lenses, and adaptors. Can also be used to
determine panel thickness adjustment.
Chrome plated bezels
tighten onto operator
(replacement for
damaged bezels)
Black plastic bezels for
square buttons
(replacement for
damaged bezels)
Used to cover and protect
pushbuttons
Standard octagonal units (chrome-pl.) AW-R8
Full shroud octagonal units (chrome-pl.) AW-RF8
Full shroud mushroom head units Ø 40mm AW-G4
Round fl ush units (black plastic) AW-RP1B
Round extended units (black plastic) AW-FP1B
Square units (black plastic) AW-Q1B
Square units with full shroud (black plastic) AW-QF1B
Waterproof lens cover for square pilot lights APW00LN
Waterproof lens cover for square illuminated buttons APW00L
Clear boot for round fl ush units OC-31
Clear boot for round extended units OC-32
*In place of asterisk, specify Rubber Boot color:
B (black), G (green), R (red), Y (yellow) - (nitril rubber)
TW-KC1
OCW-11*
Switches & Pilot Lights Display Lights Relays & Sockets Timers Terminal Blocks
Anti-Rotation Ring
Mounting Hole Plug Black rubber plug fi lls unused mounting holes in panel. OB-31
Metallic Mounting Hole
Plug
Replacement Keys Pair of keys (#0) TW-SK
Replacement Black
Sleeve for Keyswitch
Metal Button Guard Used on fl ush buttons to prevent inadvertent actuation OLW-C
Ring to prevent operator base from rotating in the mounting hole.
Used when nameplate is not used
For plugging unused mounting holes in the panel. Tighten the attached locking ring to a torque of
12 kfg-cm maximum
Degree of protection: IP66
OGL-31
LW9Z-BM
AKW2B-B
Circuit Breakers
USA: 800-262-IDEC Canada: 888-317-IDEC
593
ø22mm - TW Series
Appearance Description/Usage Part Number
Oiltight Switches & Pilot Devices
Terminal Tab Adaptor
Lock-out Adaptor
Switches & Pilot LightsDisplay LightsRelays & SocketsTimersTerminal Blocks
TW to TWTD Adaptor
Replacement Marking
Plates
Fingersafe Covers for TW Series
Appearance Description Used with Part Number
Quick- connect terminals #250 (17/64” x 3/64”) single tab TW-FA1
Used to provide lock-out protection for pushbuttons and knob selector switches:
• Up to Ø 40mm mushroom head size
(Padlock not included.)
Used to mount TW series control unit (except square units) Ø 7/8” (22mm) into a Ø 1-13/64”
(30mm) panel cut-out.
White plastic engraving plate
for use on all illuminated units
(included in each lens).
May be used to capture
printed mylar insert (not supplied by IDEC) under lens face.
Round Pushbutton (Ø14mm) ALW2B
Round Pilot Light (Ø 14mm) APW2B
Mushroom Pushbutton (Ø 14mm) ALW3B
Square Pilot Light (q 21mm) APQW1B
Square Pushbutton (q 21mm) ALQW2B
HW9Z-KL1
TWN-A1R8
Fingersafe terminal cover, adds 6mm to overall depth APW and UPQW full voltage pilot lights APS-PVL
Fingersafe terminal cover, adds 3.5mm to overall
depth. One required for each contact, only for rearmost terminals
Fingersafe terminal cover, adds 3mm to overall depth
Fingersafe terminal cover for contacts. Full voltage illuminated pushbuttons and selectors HW-VL4
Fingersafe terminal cover for full voltage adaptor, adds
3 mm to depth
Fingersafe terminal cover for half size transformer
adaptor, adds 3 mm to depth
Non-illuminated pushbuttons and selectors HW-VL2
APW and UPQW transformer pilot lights, and illuminated pushbuttons and illuminated selectors
Full voltage illuminated pushbuttons and selectors HW-VL5
Illuminated pushbuttons and selectors HW-VL6
HW-VL3
Circuit Breakers
594
www.idec.com
Loading...