IDEC PS5R-V Series Data Sheet

Download

Switching Power Supplies

PS5R-V Series

PRODUCT DESCRIPTION

DIN-rail mount switching power supplies with global approvals for both industrial and hazardous locations

KEY FE ATURES

STANDARDS COMPLIANCE

Applicable Standards

UL508

UL1310 ANSI/ISA 12.12.01 CSA C22.2 No.107.1 CSA C22.2 No.213 CSA C22.2 No.223

EN60950-1 EN50178 EN61204-3 EN50581

SEMI F47

Note 1: PS5R-VA/VB/VC/VD/VE only Note 2: EN60950-1, EN50178 only

Mark File No. or Organization

UL/c-UL Listed File No. E4 67154, E177168

TÜV SÜD

EU Low Voltage Directive, EMC Directive RoHS Directive

— EPRI

PART NUMBERS

Output Capacity Part Number Input Voltage Output Voltage Output Current

PS5R-VA05

7.5 W

10W

15W

30W

60W

90W

120W

240W

PS5R-VA12 12V 0.6A

PS5R-VA24 24V 0.3A

PS5R-VB05 5V 2.0A

PS5R-VB12 12V 1.3A

PS5R-VB24 24V 0.65A

PS5R-VC12 12V 2.5A

PS5R-VC24 24V 1.3A

PS5R-VD24 24V 2.5A

PS5R-VE24 24V 3.75A

PS5R-VF24 24V 5.0A

PS5R-VG24 24V 10.0A

100 to 240V AC (Voltage range: 85 to 264V AC / 100 to 370V DC)

Part Number Structure

Output Capacity

A: 7.5W B: 10W/15W C: 30W D: 60W E: 90W F: 120W G: 240W

PS5R - V  

Output Voltage

05: 5V 12: 12V 24: 24V

Note 3: PS5R-VA/VB only Note 4: PS5R-VA/VB/VC only

Use only for interpreting part numbers. Do not use for developing part numbers.

5V 1.5A

• Compact size preserves panel space

• Slim size (width):

22.5mm (10W/15W/30W) 36mm (60W/90W) 46m m (120W ) 60mm (240W)

• Universal Voltage Input: 85-264V AC/100 -370V DC

• Wide operating temperature range

• Spring-up terminals accept ring & fork terminals

• Approved for use in Class I Division 2 hazardous locations

• Can be installed in 6 directions

• 10W ~ 90W meet NEC Class 2 output ratings

• Overcurrent protection with auto-reset

• Meets SEMI F47 Sag Immunity (208V AC input)

• RoHS compliant

• Five-year factory warranty

SPECIFICATIONS

5V DC output PS5R-VA05 PS5R-VB05 - - - - -

Model

Output Capacity

Rated Input Voltage (Single-phase two-wire)

Frequency

Input Current (Typ.)

Inrush Current (Typ.)

Input

(Ta=25°C, cold start)

Leakage Current

Efciency (Typ.) (at rated output)

Power Factor (Typ.)

Rated Voltage/Current Adjustable Voltage Range

Output Holding Time

(Typ.) (at rated output)

Start Time

Rise Time

Input Fluctuation Load Fluctuation

Output

Temperature Change

Regulation

Ripple (including noise)

Overcurrent Protection

Operation Indicator

Between input and output terminals

Between input and ground terminals

Between output and ground terminals

Dielectric Strength

Insulation Resistance

Operating Temperature

Operating Humidity (no condensation)

Storage Temperature (No freezing)

Storage Humidity (no condensation)

Vibration Resistance

Shock Resistance

Expected Life

EMI

EMC

EMS

Safety Standards

Other Standard

Degree of Protection

Dimensions (mm)

Weight (approx.)

Terminal Screw

*At norma l temperat ure and humidi ty unless ot herwise s pecied. Note 1: DC in put voltag e is not subjec t to safety s tandards . When using on D C input, con nect a fuse to t he input ter minal for DC inp ut protec tion. Note 2 : Under stabl e state. Note 3: P S5R-VB 05 (5V DC/ 2.0A) is 10W ( Up to 3.0A at Ta = 0 to 4 0°C. Not sub ject to safe ty standa rds above 2. 0A.) Note 4: S ee the outpu t derating c urves.

Note 5: C alculation o f the expec ted life is bas ed on the act ual life of the alu minum electr olytic ca pacitor. The e xpecte d life depends o n operatin g conditions .

12V DC output PS5R-VA12 PS5R-VB12 PS5R-VC12 - - - 24V DC output PS5R-VA24 PS5R-VB24 PS5R-VC24 PS5R-VD24 PS5R-VE24 PS5R-VF24 PS5R-VG24

7.5W 15W (5V Model is 10W) 30W 60W 90W 120W 240W

(Voltage range: 85 to 264V AC/100 to 370V DC) (Load ≤ 80% at 100-105V DC)

100 to 240V AC

50/60 Hz

100V AC

230V AC

100V AC

230V AC

5V: 0.20A 12V, 24V: 0.18A

5V: 0.12A 12V, 24V: 0.10A

15A 18A 14A 36A 45A 41A 30A

120V AC 230V AC

100V AC

230V AC 100V AC 230V AC

5V: 74%, 12V: 79%, 24V: 80% 5V: 77%, 12V: 82%, 24V: 84% 12V: 83%, 24V: 85% 86% 5V: 73%, 12V: 77%, 24V: 76% 5V: 73%, 12V: 80%, 24V: 81% 12V: 85%, 24V: 87% 86% 90%

— — — — 0.99 — — — — 0.86 0.92 0.96

5V: 0.25A 12V, 24V: 0.35A

5V: 0.14A 12V, 24V: 0.19A

0.7A 1.3A 1.1A 1.4A 2.7A

0.3A 0.8A 0.6A 0.7A 1.2A

0.5mA max.

1.0mA max.

5V/1.5A, 12V/0.6A, 24V/0.3A 5V/2.0A3, 12V/1.3A, 24V/0.65A 12V/2.5A, 24V/1.3A 24V/2.5A 24V/3.75A 24V/5A 24V/10A

±10% ±5% ±10%

100V AC

230V AC

(at rated input and output)

45ms 5V: 53ms, 12V: 34ms, 24V: 36ms 12V: 13ms, 24V: 15ms 13ms 20ms 30ms

285ms

5V: 330ms 12V: 215ms

24V: 230ms

12V: 110ms 24V: 110ms 105ms 30ms 33ms 40ms

500ms max. 500ms max. 600ms max. 800ms max. 700ms max. 800ms max.

5V, 12V: 200ms max

24V: 250ms max

5V, 12V: 200ms max. 24V: 250ms max.

0.4% max.

5V: 2.5% max. 12V, 24V: 1.0% max. 1.0% max.

0.04%/°C max. (-10 to +65°C )

5V: 8% p-p max. (-25 to -10°C) 12V: 6% p-p max. (-25 to -10°C) 24V: 4% p-p max. (-25 to -10°C)

5V: 5% p-p max. (-10 to +0°C) 12V: 2.5% p-p max. (-10 to +0°C) 24V: 1.5% p-p max. (-10 to +0°C)

5V: 2.5% p-p max. (0 to +65°C)

12V: 1.5% p-p max. (0 to +65°C)

24V: 1% p-p max. (0 to +65°C)

0.05%/°C max. (-10 to +65°C )

5V: 8% p-p max. (-25 to -10°C) 12V: 6% p-p max. (-25 to -10°C) 24V: 4% p-p max. (-25 to -10°C)

5V: 5% p-p max. (-10 to +0°C) 12V: 2.5% p-p max. (-10 to +0°C) 24V: 1.5% p-p max. (-10 to +0°C)

5V: 2.5% p-p max. (0 to +65°C) 12V: 1.5% p-p max. (0 to +65°C)

24V: 1% p-p max. (0 to +65°C)

12V: 0.05%/°C max. (-10 to +50°C) 24V: 0.05%/°C max. (-10 to +55°C)

12V: 6% p-p max. (-25 to -10°C) 24V: 4% p-p max. (-25 to -10°C)

12V: 2.5% p-p max. (-10 to +0°C) 24V: 1.5% p-p max. (-10 to +0°C)

12V: 1.5% p-p max. (0 to +50°C)

24V: 1% p-p max. (0 to +55°C)

0.05%/°C max. (-10 to +55°C )

1% p-p max. (0 to

105% min. (auto reset)

LED (green)

3,000V AC, 1 minute

2,000V AC, 1 minute

500V AC, 1 minute

Between input and output terminals: 100M min. (500V DC megger) Between input and ground terminals: 100M min. (500V DC megger)

(No freezing)

-25 to +75°C

-25 to +70°C -25 to +65°C

20 to 90% RH

-25 to +75°C

20 to 90% RH

10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes

(when used with BNL6 end clips)

10 to 55Hz, amplitude 0.33mm, 2 hours each in 3 axes

10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes

300 m/s2 (30G), 3 times each in 6 directions

8 years minimum (at the rated input, 50% load, operating temperature +40°C, standard mounting direction)

EN61204-3 (Class B)

EN61204-3 (industrial)

UL508 (Listing), UL1310 Class 2, ANSI/ISA-12.12.01 CSA C22.2 No. 107.1, 213, 223 EN60950-1, EN50178

SEMI F47 (at 208V AC input only)

IP20 (EN60529)

75H × 45W × 70D 90H × 22.5W × 95D 95H × 36W × 108D 115H × 46W × 121D 125H × 60W × 125D

130g 140g 150g 260g 310g 470g 960g

M3.5

200ms max.

0.05%/°C max. (-10 to +50°C )

+55°C)

1% p-p max. (0 to

101% min. (auto reset)

(when used with BNL6 end clips)

(when used with BNL8 end clips)

4% p-p max. (-25 to -10°C)

1.5% p-p max. (-10 to +0°C)

+50°C)

88% 89%

0.05%/°C max. (-25 to +55°C

1% p-p max. (0 to +55°C)

)

89%

0.05%/°C max. (-25 to +50°C)

1% p-p max. (0 to

+50°C)

105% min. (auto reset)

10 to 55Hz, amplitude 0.21mm, 2

hours each in 3 axes

(when used with BNL6 end clips)

10 to 55Hz, amplitude 0.375mm, 2

hours each in 3 axes (when used with

BNL8 end clips)

UL508 (Listing) ANSI/ISA-12.12.01

CSA C22.2 No. 107.1, 213 EN60950-1, EN50178

10 to 55 Hz, amplitude

0.375mm, 2 hours each in 3 axes

(when used with part no.

BNL6 mounting clips)

CHARACTERISTICS

Output Current (%)

Output Current

Output Voltage (%)

Intermittent Operation

Output Voltage (%)

Operating Temperature vs. Output Current (Derating Curves)

Conditions: Natural air cooling (Operating temperature is the temperature around the switching power supply.)

PS5R-VA05, -VA12, -VA24 PS5R-VB05, -VB12, -VB24 PS5R-VC12

100

-30 -20

PS5R-VC24 PS5R-VD24 PS5R-VE24

100

-30 -20

PS5R-VF24 PS5R-VG24

100

-30 -20

Mounting B, C, D, F

-10 0 10 20 30 40 50 60 70

Operating Temperature (˚C)

Input Voltage: 85-100V AC

Mounting D, E, F

-10 0 10 20 30 40 50 60 70

Operating Temperature (˚C)

Mounting F

-10 0 10 20 30 40 50 60 70

Operating Temperature (˚C)

Mounting A,E

Mounting A, B

Mounting C

Mounting C, E

Mounting B, D

Mounting A

100

Input Voltage:

85-100V AC

Mounting B, C, D, E, F

-30 -20

-10 0 10 20 30 40 50 60 70

Operating Temperature (˚C)

100

Input Voltage:

85-100V AC

Mounting F

-10 0 10 20 30 40 50 60 70

-30 -20

Operating Temperature (˚C)

100

Mounting E

Mounting B

Mounting C, D, F

-10 0 10 20 30 40 50 60 70

-30 -20

Operating Temperature (˚C)

Mounting A

Mounting E

Mounting B, C, D

Mounting A

100

Mounting B, C, D, E, F

-10 0 10 20 30 40 50 60 70

-30 -20

Operating Temperature (˚C)

100

-30 -20

Operating Temperature (˚C)

Mounting A

Input Voltage: 85-100V AC

Mounting A

Mounting E

Mounting B, C, D, F

-10 0 10 20 30 40 50 60 70

Input Voltage vs. Output Current (Derating Curves) Ta=25°C

PS5R-VB05, -VB12, -VB24, -VC12, -VC24, -VD24,

-VE24, -VF24

100

85 100 264

(ACV)

100

(DCV) 140 370

Input Voltage (V)

PS5R-VA05, -VA12, -VA24, -VG24

100

(%)

(ACV) 100 (DCV) 105100 370

Input voltage (V)

264

Overcurrent Protection Characteristics

PS5R-VA/VB/VC/VD/VF PS5R-VE24 PS5R-VG24

100

-30

0 100

Output Current (%)

105 and over

10 0

Intermittent Operation

Output Current (%)

100

101 and over

10 0

Intermittent Operation

Output Current (%)

100

105 and over

Operating Temperature Approved by Safety Standards

Part Number

Mounting A Mounting B Mounting C Mounting D Mounting E Mounting F

PS5R-VA05, -VA12, -VA24 65 60 60 60 65 60

PS5R-VB05, -VB12, -VB24 65 60 60 60 60 60

PS5R-VC12 50 45 45 45 45 45

PS5R-VC24 55 55 50 45 45 45

PS5R-VD24 55 40 40 40 45 35

PS5R-VE24 50 40 40 40 45 40

PS5R-VF24 55 40 45 40 45 35

PS5R-VG24 50 35 30 30 45 30

MOUNTING STYLE

UL508, CSA C22.2 No.107.1, ANSI/ISA12.12.01, EN60950-1, EN50178

Mounting A

(Vertical, standard)

Mounting B

(Upright)

Mounting C

(Right side up)

Mounting D

(Left side up)

Front Panel

PS5R-VA PS5R-VB/VC PS5R-VD/VE/VF PS5R-VG

INPU T

100 -240 VAC

VR. ADJ

OU TP UT

ACCESSORIES

Panel Mounting Bracket

Applicable Switching Power Supply Part Number Remarks

PS5R-VB PS5R-VC

PS5R-VD

PS5R-VE PS5R-VF PS9Z-5R1E —

PS5R-VG

Note 2: Used when installing on a panel directly, PS5R-VA model does not require panel mounting bracket.

INPUT 50/60Hz

DC ON

VR. ADJ

OUTPUT

-V

PS9Z-5R1B — PS9Z-5R2B For side mounting

PS9Z-5R1C —

PS9Z-6R1F —

PS9Z-6R2F For side mounting

Mounting E

(Upside down)

Mounting F

(Downward)

Marking Name Description

L, N

+V, -V

VR.ADJ

DC ON

AC Input Terminal Voltage range: 85 to 264V AC/100 to 370V DC

Ground Terminal

DC Output Terminals

Output Voltage Adjustment

Operation Indicator (green) Illuminates when the output voltage is on.

Be sure to connect this terminal to a proper ground.

+V: Positive output terminal

-V: Negative output terminal Allows adjustment within ±10%. (VE = ±5%)

Turning clockwise increases the output voltage. Turning counterclockwise decreases the output voltage.

DIN Rail (35mm-wide)

Length Part Number Material

1000mm BNDN1000 Aluminum

End Clip

Part Number

BNL6

BNL8

DIMENSIONS (MM)

PS5R-VA

PS5R-VA PS5R-VB/VC

6-M3.5 Screw Terminal

5-M3.5

Screw Terminal

62.5

PS5R-VD/VE

10 10

79 8

26 35

38.5 45

5-M3.5

Screw Terminal

7.35

19.9

35.3

3.8

12.2 8.2

61.6

9.5

22.5

27.3

4.4 35.3

3.8

PS5R-VF

5-M3.5

108

98 8.5

4.5 24.935.3

3.8

11.5 11.5

Screw Terminal

115

121

4.5 44.935.3

3.8

PS5R-VG

8-M3.5 Screw Terminal

9.3

10 6 .5

9.5 9 .5

9.5 9.5 9.5 9.5

125

3.8

5.5

MTBF*

PS5R-VA: 1,150,000H minimum PS5R-VB: 900,000H minimum PS5R-VC: 650,000H minimum PS5R-VD: 450,000H minimum PS5R-VE: 380,000H minimum

12 54.5

35 .3 44 .9

PS5R-VF: 350,000H minimum

MIL-HDBK-217FN2

(GB, 30°C)

PS5R-VG: 290,000H minimum *MTBF stands for Mean Time Between Failure, which is calculated according to

statistical device failures, and indicates reliability of a device. It is the statistical representation of the likelihood of the unit to fail and does not necessarily represent the expected life of a product.

Panel Mounting Bracket When installed on switching power supply

148.6

PS9Z-5R1B

2-M4 or 2- ø 4.5 holes

13.616.4

112

120

24.7

PS9Z-5R2B Side-mount

110

102.0

62.9

PS9Z-5R1C

105

115

26 38

PS9Z-5R1E

112

2-M4 or 2- ø 4.5 holes

102

105

Mounting hole layout when installing on a panel directly

2-M4 or 2- ø 4.5 holes

Mounting hole layout when installing on a panel directly

2-M4 or 2- ø 4.5 holes

96.7

10.2

9.9

10.0

Side View

28.8

Front View

109.8

122.8

Front View

Side View

Front View Side View

10.2

5.5

125

135

PS9Z-6R1F

135

145

PS9Z-6R2F Side-mount

138.6

56 70

125

Mounting hole layout when installing on a panel directly

138.6

135

Mounting hole layout when installing on a panel directly

Front View Side View

10.5

145

10.5

Front View

62.3

9.9

29.5

11.8

130.6

Side View

36 48

4-M4 or 4- ø 4.5 holes

28 39

4-M4 or 4- ø 4.5 holes

Mounting hole layout for side

mounting

Side View Back View

11.8

Mounting Screws (4 -M3×6 countersunk screws)

SAFETY PRECAUTIONS

Mounting Removal

Clamp

The PS5R-V should be placed in a proper enclosure. It is designed to be used with general electrical equipment and industrial electric devices

• Do not use switching power supplies with electric equipment whose malfunction or inadvertent operation may damage the human body or life directly.

• Make sure that the input voltage and output current do not exceed the ratings. If the input voltage and output current exceed the ratings, electric shock, fire, or malfunction may occur.

• Do not touch the terminals of the switching power supply while input voltage is applied, otherwise electric shock may occur.

• Provide the final product with protection against malfunction or damage that may be caused by malfunction of the switching power supply.

• Operating temperatures should not exceed the ratings. Be sure to note the derating characteristics. If the operating temperature exceeds the ratings, electric shock, fire, or malfunction may occur.

• Blown fuses indicate that the internal circuits are damaged. Contact IDEC for repair. Do not just replace the fuse and reoperate, otherwise electric shock, fire, or malfunction may occur.

• Do not use the switching power supplies to charge rechargeable batteries.

• Do not overload or short-circuit the switching power supply for a long period of time, otherwise the internal elements may be damaged.

• Do not disassemble, repair, or modify the power supplies, otherwise the high voltage internal part may cause electric shock, fire, or malfunction.

• The fuse inside the PS5R-V switching power supply is for AC input. Use an external fuse for DC input.

OPERATING INSTRUCTIONS

Notes for installation

• Do not close the top or bottom openings of the PS5R-V to allow for heat radiation by convection.

• When mounting multiple PS5R-V switching power supplies side by side, maintain a minimum of 10 mm clearance. Observe the derating curves in consideration of the ambient temperature.

Mounting on DIN Rails

1. Use a 35mm-wide DIN rail.

2.Place the PS5R-V on the DIN rail as shown with input terminal side up (➀), and press the PS5R-V towards the DIN rail (➁). Make sure that the PS5R-V is installed rmly.

3. Use BNL6 end clips to ensure power supplies do not slide off the end of the DIN rail. Use of BNL8 end clips is recommended when excessive vibration or shock is anticipated.

Removal

• Insert a flat screwdriver into the slot in the clamp, and pull out until it clicks (➀). The lock mechanism is released and the PS5R-V can be removed (➁). When mounting the PS5R-V again, push in the latch first.

Installing a Panel Mounting Bracket

Panel Mounting Bracket (PS9Z-5R1, PS9Z-6R1F)



Latch



Tab



Slot

Power Supply

 Push in the latch to LOCK

position.

LOCK

UNLOCK

 Install the tab on the panel

mounting bracket into the slot on the power supply.

10mm minimum

• When the derating voltage may exceed the recommended value, provide forced air-cooling.

• Make sure to wire the ground terminal correctly.

• For wiring, use wires of heat resistance of 60C or higher (PS5R-VB: 80C or higher). Use copper wire of the following sizes, according to the rated current.

Terminal Wire Size (allowable current) Wire Type

Input AWG 18 to 14

Output AWG18 to 14 (AWG18: 7A, AWG16:

10A, AWG14: 15A)

Cross-Sectional are AWG18: 0.82mm2, AWG16: 1.31mm2, AWG14: 2.0mm

Copper Solid/Stranded

Applicable crimp terminal (reference)

ø3.6min.

6.6 max. 4 max.

• Recommended tightening torque of the input and output terminals is 1.0 to

1.3Nm (0.8N·m for UL).

5.5 min.



LOCK

Panel Mounting Bracket (PS9Z-5R2B)

Tab





Latch

Power Supply





LOCK

 Install the brackets as shown

on the left.

 Ensure that the panel mounting

bracket is locked by the latch.

 Pull out the latch to

UNLOCK position.

LOCK

UNLOCK

 Insert the tab on the panel

mounting bracket into the slot on the power supply.

 Push in the latch to LOCK

position.

 Ensure that the panel mounting

bracket is locked by the latch.

Installing PS9Z-6R2F Side-mount Panel Mounting Bracket

(a)

L N

(b)

Install the bracket on the switching power supply using four M3 × 6 countersunk screws supplied with the bracket. Recommended tightening torque is 0.5 to 0.6N.m (should be in the center positions)

Adjustment of Output Voltage

The output voltage can be adjusted within ±10% (VE: ±5%) of the rated output voltage by using the VR.ADJ control on the front. Turning the VR.ADJ clockwise increases the output voltage. Turning the VR.ADJ counterclockwise decreases the output voltage.

Overcurrent Protection

The output voltage drops automatically when an overcurrent flows due to an overload or short circuit. Normal voltage is auto matically restored when the load returns to normal conditions.

Insulation/Dielectric Test

When performing an insulation/dielectric test, short-circuit the input (between L and N) and output (between +V and -V). Do not apply or interrupt the voltage quickly, otherwise surge voltages may be generated and the PS5R-V may be damaged.

Notes for Operation

• Output interruption may indicate blown fuses. Contact IDEC.

• The PS5R-V switching power supply contains an internal fuse for AC input. When using DC input, install an exter nal fuse. To avoid blown fuses, select a fuse in consideration of the rated current of the internal fuse.

Rated Current of Internal Fuses

Part Number Internal FuseRated Current

PS5R-VB/VC

PS5R-VD/VE/VF

PS5R-VG

6.3A

• Avoid overload and short-circuit for a long period of time, oth erwise the internal elements may be damaged.

WARRANTY

IDEC warranties the PS5R-V switching power supply for a period of five years from the date of shipment.

Scope

IDEC agrees to repair or replace the PS5R-V switching power supply if the product has been operated under the following conditions. The maximum value of output capacity is within the range shown in “Operating Temperature vs. Output Current on page 3.

1. Average operating temperature (ambient temperature of switching power supply) is 40°C maximum.

2. The load is 80% maximum.

3. Input voltage is the rated input voltage.

4. Standard mounting style

• DC input operation is not subject to safety standards.

Rust and Scratches on Metal parts

Bonded metal parts are used for the PS5R-V. Rust on the edge and scratches on the surfaces may be developed depending on the storage condition, but the performance of the PS5R-V is not affected.

Noise

Small acoustic noise inside the PS5R-V may be heard depending on the input voltage and load, but the performance of the PS5R-V is not affected.

Series Operation

Series operation is allowed. Connect Schottky barrier diodes D as shown below. Select a Schottky diode in consideration of the rated current. The diode’s reverse voltage must be higher than the PS5R-V’s output voltage.

L N

LN+V

Load

L N

+V –V

–V

LN+V

+V –V

Load

–V

Parallel Operation

Parallel operation is not possible to increase the output capacity, because the internal elements and load may be damaged.

Backup Operation

Backup operation is a connection method of two switching power supplies in parallel for emergency. Normally one switching power supply has a sufficient output. If one switching power supply fails, another one operates to continue the output. Make sure that the sum of power consumption by load and diode is not greater than the rated wattage (rated voltage × rated current) of one switching power supply.

OUT

−

IN OUT

−

Select a diode in consideration of: Diode’s current must be more than double the PS5R-V’s output current. Take heat dissipation into consideration.

IDEC shall not be liable for other damages including consequential, contingent or incidental damages. Warranty does not apply if the PS5R-V switching power supply was subject to:

1. Inappropriate handling, or operation beyond specifications.

2. Modification or repair by other than IDEC.

3. Failure caused by other than the PS5R-V switching power supply.

4. Failure caused by natural disasters.

Load

1612211733

IDEC PS5R-V Series Data Sheet

Specifications and Main Features

Frequently Asked Questions

User Manual