Programmable Logic Controllers MicroSmart Series
General Specifications (CPU Module)
Rated Voltage
Allowable Range
Rated Frequency
Maximum Input Current
Max. Power
Consumption
Allowable Momentary
Power Interruption
Dielectric Strength
Insulation Resistance
Noise Resistance
Inrush Current
FC4A-C10R2
FC4A-C10R2C
AC Power Type: 50/60 Hz (47-63 Hz) —
0.25A (85V AC or
24V DC)
30VA/264V AC *
AC
20VA/100V AC
DC 3.8W/24V DC 4.6W/24V DC 8.7W/24V DC Not applicable
10 msec at the rated inputs and outputs (IEC61131) 10 msec (at 24V DC)
Between power and terminal: 1500V AC, 1 min
Between I/O and terminal: 1500V AC, 1 min
Between power and terminal: 10 MΩ (min), 500V DC
Between I/O and terminal: 10 MΩ (min), 500V DC
AC or DC power terminal: 1.5 kV, 50ns to 1µs
I/O terminal (coupling clamp): 1.5 kV, 50ns to 1µs
35A max. 35A max. 40A max. 50A maximum (24V DC)
FC4A-C16R2
FC4A-C16R2C
AC Power Type: 100-240V AC
DC Power Type: 24V DC
AC Power Type: 85-264V AC
DC Power Type: 16.0 - 31.2V DC
0.30A (85V AC or
24V DC)
31VA/264V AC *
22VA/100V AC
Power Supply Wire
Operating Temperature
Storage Temperature
CPU General Specifications
Operating Humidity
Altitude
Pollution Degree
Corrosion Immunity
Degree of Protection
Grounding Wire
Vibration Resistance
DIN rail mounted: 10 to 57Hz / amplitude 0.075mm, 57 to 150Hz / acceleration 9.8m/s2 (1G)
Direct mounted: 2 to 25Hz / amplitude 1.6mm, 25 to 100Hz / acceleration 39.2m/s2 (4B) in each of 3 axes
16 AWG 22 AWG
Shock Resistance
Weight
1. * CPU module power consumption includes 250 mA sensor power.
2. ** CPU module (including 250 mA sensor power) + 4 I/O modules
3. # CPU module + 7 I/O modules
AC 230g 250g 305g Not Applicable
DC 240g 260g 310g 140g 185g 180g
FC4A-C24R2
FC4A-C24R2C
0.45A (85V AC or
24V DC) **
40VA/264V AC **
33VA/100V AC
–25 to +70°C
30-95% Level RH1 (no condensation)
Operation: 0 to 2,000m (0 to 6,595 ft)
Transport: 0 to 3,000m (0 to 9.840 ft)
Free from corrosive gases
15G, 11ms, 3 shocks in each of 3 axes
FC4A-D20K3
FC4A-D20S3
20.4 to 26.4V DC (including ripple)
0.56A (26.4V DC) # 0.70A (26.4V DC) #
15W/26.4V DC # 19W/26.4V DC #
Between power and terminal: 500V AC, 1 min
Between I/O and terminal: 1500V AC, 1 min
Between power and terminal: 10 MΩ (min)
Between I/O and terminal: 10 MΩ (min)
DC power terminals: 1.0 kV, 50 nsec to 1µsec
I/O terminals (coupling clamp): 1.5 kV, 50 nsec to 1µsec
22 - 18AWG
0 to 55°C
2 (IEC60664)
IP20
FC4A-D20RK1
FC4A-D20RS1
24V DC
FC4A-D40K3
FC4A-D40S3
J
Programmable Logic Controllers
Communication Port 1 Specifications
Standards
Maximum Baud Rate
Maintenance Communication
User Communication
Modem Communication
Data Link Communication
Cable
Isolation between Internal Circuit
and Communication Port
EIA RS232C
19200 bps
Possible
Possible
Not possible
Not possible
Special Cables: FC2A-KC4C, FC2A-KP1C, FC4A-KC1CA, FC4A-KC2CA
Not isolated
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-15
MicroSmart Series Programmable Logic Controllers
Function Specifications (CPU Module)
FC4A-C10R2
FC4A-C10R2C
Control System
Instruction words
Program Capacity
38 advanced 40 advanced 46 advanced 53 advanced 70 advanced
4,800 bytes
(800 steps)
User Program
Storage
Processing Time
Expandable I/O
Modules
RAM Backup
I/O Points
Internal Relay
Shift Register
Data Register
(does not include expansion I/O service, clock function processing, data link processing and interrupt processing)
––4 modules 7 modules
Backup Data: Internal relay, shift register, counter, data register
Backup Duration: Approx. 30 days (typical) at 25° C after backup battery fully charged
Battery: Lithium secondary battery
Charging Time: Approx. 15 hours for charging from 0% to 90% of full charge
Battery Life: 5 years
Replaceability: Impossible to replace battery
6 input, 4 output 9 input, 7 output
256 1024
64 128
400 1300
Expansion Data
Register
J
Counter
32 100
Timer (1-sec,
100-msec,
32 100
10-msec, 1-msec)
Self-Diagnostic
Function
CPU Function Specifications
Power failure check, watchdog timer, data link connection, user program EEPROM sum check,
timer/counter preset value sum check, user program RAM sum check, keep data, user program syntax, user program writing,
CPU module, clock IC, I/O bus initialize, user program execution
Input Filter
Catch Input/
Interrupt Input
High-Speed Counter
Analog
4 input (I2 through I5) Minimum turn on pulse width: 40 µsec maximum Minimum turn off pulse width: 150 µsec maximum
Total 4 points: Single/two-phase selectable: 20kHz (1 point)
Single-phase: 5kHz (3 points)
Counting Range 0 to 65535 (16 bits), Operation Mode: Rotary encoder mode and adding counter mode
1 point 2 points 1 point
Potentiometer
Analog Voltage Input
Pulse Output
Sensor Power
Programmable Logic Controllers
Supply
Port 1
Port 2 (optional)
24V DC (+10% to -15%), 250 mA, no overload detection
Isolated from the internal circuit
RS232C Maintenance Communication, User Communication, Modem Communication
— Possible: RS232C or RS485 (Maintenance communication, data link)
Clock Function
(optional)
Memory Cartridge
Select either clock or memory cartridge
(optional)
HMI Module (optional)
FC4A-C16R2
FC4A-C16R2C
15,000 bytes
(2,500 steps)
Internal EEPROM, Memory cartridge (option: EEPROM)
Basic instruction: 1.65 msec (1000 steps); END processing: 0.64 msec
—
—2 points, max. frequency 20kHz
Possible
Possible Possible using HMI Base Module
FC4A-C24R2
FC4A-C24R2C
Stored program system
35 basic instructions
27,000 bytes
(4,500 steps)
Calculated 6 bytes per step
14 input, 10 output
Expansion: 64 I/O
— 6000
3 to 15 msec (1-msec increments)
Data Range: 0 to 255
FC4A-D20K3
FC4A-D20S3
27,000 bytes
(4,500 steps)
12 input, 8 output
Expansion: 128 I/O
Total 4 points: Single/two-phase selectable: 20kHz (2 points)
Single-phase: 5kHz (2 points)
1 point, 0 to 10V DC Input Voltage Range, approx. 100kΩ Input
Impedance, data range 0-255 (8 bit)
Year, month, day, day of week, hour, minute, second
FC4A-D20RK1
FC4A-D20RS1
31,200 bytes
(5,200 steps)
12 input, 8 output
Expansion: 224 I/O
—
Possible
Possible
FC4A-D40K3
FC4A-D40S3
24 input, 16 output
Expansion: 224 I/)
J-16 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Programmable Logic Controllers MicroSmart Series
DC Input/Relay Output Specifications (CPU Module)
DC Input Specifications for CPU modules
FC4A-C10R2C
Rated Input Voltage
Allowable Range
Rated Input Current
Input Impedance
OFF/ON
OFF/ON Time
ON/OFF
Input Points
On Mother Board
Connector
Insertion/Removal
Durability
Isolation
Input Type
External Load for I/O Interconnection
Signal Determination Method
Effect of Improper Input Connection
Cable Length
FC4A-C10R2
24V DC sink / source input signal
20.4 to 28.8V DC 20.4 to 26.4V DC
I0, I1: 11mA, I2 to I7, I10 to I15: 7mA I0, I1, I6, I7: 5mA/point, I2 to I5, I10 to I27: 7mA/point
I0, I1: 2.1kΩ, I2 to I7, I10 to I15: 3.4kΩ I0, I1, I6, I7: 5.7kΩ, I2 to I5, I10 to I27: 3.4kΩ
I0 to I5: 35µsec + Filter Value
I6, I7, I10 to I15: 40µsec + Filter Value
I0, I1: 45µsec + Filter Value
I2 to I7, I10 to I15: 150µsec + Filter Value
6 inputs
6/1 common
Between input terminals: Not isolated
Internal circuit: Photocoupler isolated
Type 1 (IEC61131)
Not needed
Static
Both sinking and sourcing input signals can be connected. If any input exceeding the rated value is applied,
permanent damage may be caused.
3m (9.84 ft)
FC4A-C16R2
FC4A-C16R2C
9 inputs
9/1 common
—
— 100 times minimum
FC4A-C24R2
FC4A-C24R2C
14 inputs
14/1 common
FC4A-D20K3
FC4A-D20S3
I0 to I7: 35µsec + Filter Value
I10 to I27: 40µsec + Filter Value
I0, I1, I6, I7: 45µsec + Filter Value
I2 to I5, I10 to I27: 150µsec + Filter Value
12 inputs
12/1 common
FL26A2MA
(Oki Electric
Cable)
FC4A-D20RK1
FC4A-D20RS1
12 inputs
12/1 common
MC1.5/13-G-3.81BK
(Phoenix Contact)
FC4A-D40K3
FC4A-D40S3
24 inputs,
12/1 common
FL26A2MA
(Oki Electric
Cable)
Relay Output Specifications for CPU modules
FC4A-C10R2
FC4A-C10R2C
Output Points
COM0
Output Points per Common
COM1
COM2
COM3
Type of Output
Maximum Load Current Per point
Per Common
Minimum Switching Load
Initial Contact Resistance
Electrical Life
Mechanical Life
Rated Load Current (resistive/inductive)
Dielectric Strength
On Mother
Board
Connector
Insertion/
Removal
Durability
FC4A-C16R2
FC4A-C16R2C
4 points 7 points 10 points 8 points
3 points 4 points 4 points
1 point 2 points 4 points 3 points
–1 point 1 point 2 points
––1 point 1 point
0.1mA, 0.1V DC (reference value)
30mΩ maximum
100,000 operations (rated load) @ 1,800 operations/hr
200,000 operations (no load) @ 18,000 operations/hr
240V AC/2A, 24V DC/2A (30V DC / 2A)
Between output and terminals: 1500V AC, 1 minute
Between output terminals and internal circuit: 1500V AC, 1 minute
Between output terminals (COMs): 1500 V AC, 1 minute
—
— 100 times minimum
FC4A-C24R2
FC4A-C24R2C
1NO
2A
8A
FC4A-D20RK1
FC4A-D20RS1
2 points
(transistor output)
MC1.5/16-G-3.81BK
(Phoenix Contact)
J
Programmable Logic Controllers
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-17
MicroSmart Series Programmable Logic Controllers
Transistor Sink and Source Output Specifications (CPU Module)
Transistor Sink and Source Output Specifications for CPU modules
Output Points and Common Line
Type of Output
Rated Load Voltage
Operating Load Voltage Range
Rated Load Current
Maximum Load Current
Voltage Drop (ON Voltage)
Inrush Current
Leakage Current
Clamping Voltage
Maximum Lamp Load
Inductive Load
External Current Draw
Isolation
Connector
Output Delay
J
On Mother Board
Insertion/Removal
Durability
Turn ON time
Turn OFF time
FC4A-D20K3
FC4A-D20S3
8 points, 8/1 common 2 points, 2/1 common 16 points, 8/1 common
FC4A-D20K3/D20RK1/D40K3 = Sink Output
FC4A-D20S3/D20RS1/D40S3 = Source Output
1V maximum (voltage between COM and output terminals when output is on)
100mA maximum, 24V DC (power voltage at the +V or -V terminal)
Between output terminal and internal circuit: Photocoupler isolated
Between output terminals: Not isolated
FL26A2MA
(Oki Electric Cable)
5 µs (Q0, Q1), 300 µs max (Q2 to Q7, Q10 to Q17)
5 µs (Q0, Q1), 300 µs max (Q2 to Q7, Q10 to Q17)
FC4A-D20RK1
FC4A-D20RS1
24V DC
20.4 to 28.8V DC
0.3A per output point
1A per common line
1A maximum
0.1 mA maximum
39V±1V
8W
L/R = 10ms (28.8V DC, 1Hz)
MC1.5/16-G-3.81BK
(Phoenix Contact)
100 times minimum
FC4A-D40K3
FC4A-D40S3
FL26A2MA
(Oki Electric Cable)
Programmable Logic Controllers
J-18 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Programmable Logic Controllers MicroSmart Series
Input/Relay Output Specifications (Expansion Modules)
Input Module Specifications
Input Points
Rated Input Voltage
Input Voltage Range
Rated Input Current
Input Impedance
Input Delay Time
Between input
Isolation
terminals
Internal circuit
External Load for I/O
Interconnection
Signal Determination Method
Effect of Improper Input Connection
Cable Length
On Mother Board
Connector
Insertion/Removal
Durability
Internal
All Inputs ON
Current
Draw
All Inputs OFF
Weight
Relay Output Module Specifications
Output Points and Common Lines
Output Type
Maximum Load Current
Minimum Switching Load
Initial Contact Resistance
Electrical Life
Mechanical Life
Rated Load (resistive/inductive)
Dielectric Strength
Connector
Internal Current Draw
Weight
8 points (8/1 common) 16 points (16/1 common) 32 points (16/1 common) 8 points (4/1 common)
MC1.5/10-G-3.81BK (Phoenix contact) FL20A2MA (Oki Electric Cable)
per point
per common
On Mother Board
Insertion/Removal
Durability
All Inputs ON
All Inputs OFF
DC Input AC Input
FC4A-N08B1 FC4A-N16B1 FC4A-N16B3 FC4A-N32B3 FC4A-N08A11
24V DC sink/source input signal 100 - 120V AC (50-60Hz)
20.4 to 28.8V DC 85 to 132V AC
7mA/point (24V DC) 5mA/point (24V DC) 7.5mA/pt (100V AC, 60Hz)
3.4 kΩ 4.4 kΩ 0.8kΩ (60Hz)
ON time: 4 msec
OFF time: 4 msec
Not isolated
Photocoupler isolated 2500V (photocoupler isolated)
Not needed
Static
If any input exceeding the rated value is applied, permanent damage may be caused.
25 mA (5V DC)
0 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
85g 100g 65g 100g –
Both sinking and sourcing input signals can be connected.
3m (9.84 ft) in compliance with electromagnetic immunity
100 times minimum
40 mA (5V DC)
0 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
35 mA (5V DC)
0 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
65 mA (5V DC)
0 mA (24V DC)
10 mA (5V DC)
0 mA (24V DC)
ON time: 25 msec
OFF time: 30 msec
In the same commons: not isolated
In different commons: 500V
60mA (5V DC)
0mA (24V DC)
30mA (5V DC)
0mA (24V DC)
FC4A-R081 FC4A-R161
8 points (4/1 common) 16 points (8/1 common)
1NO
2A
7A 8A
0.1 mA/0.1V DC (reference value)
30 mΩ maximum
100,000 operations minimum
(rated load 1,800 operations/hour)
20,000,000 operations minimum
(no load 18,000 operations/hour)
240V AC/2A, 30V DC/2A
Between output and terminals: 1500V AC, 1 minute
Between output terminals and internal circuit: 1500V AC, 1 minute
Between output terminals (COMs): 1500 V AC, 1 minute
MC1.5/11-G-3.81BK
(Phoenix contact)
100 times minimum
30 mA (5V DC)
40 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
110g 145g
MC1.5/10-G-3.81BK
(Phoenix contact)
45 mA (5V DC)
75 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
J
Programmable Logic Controllers
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-19
MicroSmart Series Programmable Logic Controllers
Transistor Output Specifications (Expansion Modules)
Transistor Output Module Specifications
Output Points
Output Type
Rated Load Voltage
Operating Load Voltage Range
Rated Load Current
Maximum Load Current
Voltage Drop (ON Voltage)
Inrush Current
Leakage Current
Clamping Voltage
Maximum Clamping Load
Inductive Load
External Current Draw
Isolation
Connector
J
Internal Current Draw
Output Delay
Weight
per point
per common
Type (on Mother
Board)
Insertion/Removal
Durability
All Inputs ON
All Inputs OFF
Turn ON time
Turn OFF time
FC4A-T08K1
FC4A-T08S1
8 points (8/1 common) 16 points (16/1 common) 32 points (16/1 common)
FC4A-TK: Transistor sink output
FC4A-TS: Transistor source output
0.3A per output point
(at 28.8V DC)
0.36A (at28.8V DC) 0.12A (at 28.8V DC)
3A (at 28.8V DC) 1A (at 28.8V DC)
1V maximum (between COM and output terminals when output is on)
FC4A-TK: 100mA maximum, 24V DC (power voltage at the +V)
FC4A-TS: 100mA maximum, 24V DC (power voltage at the -V)
Between output terminal and internal circuit: Photocoupler isolated
MC1.5/10-G-3.81BK
(Phoenix contact)
10mA (5V DC)
20mA (24V DC)
5mA (5V DC)
0mA (24V DC)
Between output terminals: Not isolated
85g 70g 105g
FC4A-T16K3
FC4A-T16S3
24V DC
20.4 to 28.8V DC
0.1A per output point (at 28.8V DC)
1A maximum
0.1A maximum
39V ± 1V
8W
L/R = 10 msec (DC 28.8V, 1Hz)
FL20A2MA (Oki Electric Cable)
100 times minimum
10mA (5V DC)
40mA (24V DC)
5mA (5V DC)
0mA (24V DC)
300µsec maximum
300µsec maximum
FC4A-T32K3
FC4A-T32S3
20mA (5V DC)
70mA (24V DC)
10mA (5V DC)
0mA (24V DC)
Programmable Logic Controllers
J-20 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Programmable Logic Controllers MicroSmart Series
Combination I/O Specifications (Expansion Modules)
Combination I/O Module Specifications
Input Points
Rated Input Voltage
Input Voltage Range
Range Input Current
Input Impedance
Turn ON Time
Turn OFF Time
Isolation
External Load for I/O Interconnection
DC Input Specifications
Signal Determination Method
Effect of Improper Input Connection
Cable Length
FC4A-M08BR1 FC4A-M24BR2
4 points (4/1 common) 16 points (16/1 common)
24V DC sink/source input signal
20.4 to 28.8V DC
7 mA/point (24V DC)
3.4 kΩ
4 msec (24V DC)
4 msec (24V DC)
Between input terminals: Not isolated
Internal circuit: Photocoupler isolated
Not needed
Static
Both sinking and sourcing input signals can be connected. If any input
exceeding the rated value is applied, permanent damage may be caused.
3m (9.84 ft) in compliance with electromagnetic immunity
Output Points
Output Type
Maximum Load Current
Minimum Switching Load
Initial Contact Resistance
Electrical Life
Mechanical Life
Rated Load (resistive/inductive)
Relay Output Specifications
Dielectric Strength
Connector
Internal Current Draw
Weight
per point
per common
on Mother Board
Insertion/Removal
Durability
All Inputs ON
All Inputs OFF
4 points (4/1 common) 8 points (8/2 common)
1NO
2A
7A
0.1 mA/0.1V DC (reference value)
30 mΩ maximum
100,000 operations minimum (rated load 1,800 operations/hour)
20,000,000 operations minimum (no load 18,000 operations/hour)
240V AC/2A, 30V DC/2A
Between output and or terminals: 1,500V AC, 1 minute
Between output terminal and internal circuit: 1,500V AC, 1 minute
Between output terminal (COMs): 1,500V AC, 1 minute
MC1.5/11-G-3.81BK
(Phoenix contact)
100 times minimum —
25 mA (5V DC)
20 mA (24V DC)
5 mA (5V DC)
0 mA (24V DC)
95g 140g
Input: F6018-17P (Fujicon)
Output: F6018-11P (Fujicon)
65 mA (5V DC)
45 mA (24V DC)
10 mA (5V DC)
0 mA (24V DC)
J
Programmable Logic Controllers
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-21
MicroSmart Series Programmable Logic Controllers
Analog I/O Specifications (Expansion Modules)
Analog I/O Module Specifications
FC4A-L03A1 FC4A-L03AP1 FC4A-J2A1 FC4A-K1A1
Input Points
Input Signal Type
Output Points
Output Signal Type
Voltage Input (0 to 10V DC)
Current Input (4 to 20 mA DC)
11—1
Voltage Output (0 to 10V DC)
Current Output (4 to 20 mA DC)
Rated Power Voltage
Allowable Voltage Range
On Mother Board
Connector
Internal
Current
Draw
Insertion/Removal
Durability
Internal Power
External Power
100 times minimum
50 mA (5V DC)
0 mA (24V DC)
40 mA (24V DC) 40 mA (24V DC) 40 mA (24V DC) 40 mA (24V DC)
Weight
Analog Output Specifications
Output Signal Type
Output Range
Load Impedance
Applicable Load Type
Setting Time
Total Output System Transfer Time
Maximum Error at 25°C
J
Temperature Coefficient
Repeatability after Stabilization Time
Output
Error
Output Voltage Drop
Non-lineality
Output Ripple
Overshoot
Total Error
Digital Resolution
Output Value of LSB
Data
Data Type in Application Program
Monotonicity
Current Loop Open
Maximum Temporary Deviation during Electrical Noise Tests
Noise
Cable
Crosstalk
Programmable Logic Controllers
Dielectric Strength
Type of Protection
Effect of Improper Output Connection
Selection of Analog Output Signal Type
Calibration or Verification to Maintain Rated Accuracy
222—
Thermocouple
Resistance Thermometer
Voltage Output (0 to 10V DC)
Current Output (4 to 20 mA DC)
20.4 to 28.8V DC
MC1.5/11-G-3.81BK (Phoenix contact)
50 mA (5V DC)
0 mA (24V DC)
Voltage Input (0 to 10V DC)
Current Input (4 to 20 mA DC)
—
24V DC
50 mA (5V DC)
0 mA (24V DC)
85g
FC4A-L03A1, FC4A-L03AP1, FC4A-K1A1
Voltage Output Current Output
0 to 10V DC 4 to 20 mA DC
2 kΩ minimum 300Ω maximum
Resistive load
20 msec
20 msec + 1 scan time
±0.2% of full scale
±0.015% of full scale/°C
±0.5% of full scale
±1% of full scale —
±0.2% of full scale
1 LSB maximum
0%
±1% of full scale
4096 increments (12 bits)
2.5 mV 4 µA
0 to 4095 (12-bit data); -32768 to 32767 (optional range designation)
±3% max. when a 500V clamp is applied to the power and I/O wiring
Twisted pair shielded cable recommended for improved noise immunity
No crosstalk because of 1 channel output
Photocoupler between output and internal circuit
See note on page J-23
Yes
— Detectable (See note on page J-23)
500V between output and power circuit
No damage
Using software programming
Impossible (approx. 10 years)
—
Voltage Output (0 to 10V DC)
Current Output (4 to 20 mA
DC)
50 mA (5V DC)
0 mA (24V DC)
J-22 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Programmable Logic Controllers MicroSmart Series
Analog Input Specifications (Expansion Modules)
Analog Input Specifications
FC4A-L03A1, FC4A-J2A1 FC4A-L03AP1
Input Signal Type
Input Range
Input Impedance
Allowable Conductor Resistance
Input Detection Current
Sample Duration Time
Sample Repetition Time
Total Input System Transfer Time
Type of Input
Operating Mode
Conversion Method
Maximum Error at 25°C
Temperature Coefficient
Input Error
Repeatability after
Stabilization Time
Non-lineality
Maximum Error
Digital Resolution
Input Value of LSB
Data
Data Type in Application
Program
Monotonicity
Input Data Out of Range
Maximum Temporary
Deviation during
Electrical Noise Tests
Common Mode
Noise
Resistance
Characteristics
Common Mode Voltage
Input Filter
Cable
Crosstalk
Dielectric Strength
Type of Protection
Effect of Improper Input Connection
Maximum Permanent Allowed
Overload (No damage)
Selection of Analog Input Signal Type
Calibration or Verification to Maintain
Rated Accuracy
NOTES FOR ANALOG EXPANSION UNITS:
1. * Total input system transfer time = Sample repetition time x 2 + 1 scan time
2. ** The 12-bit data (0 to 4095) processed in the analog I/O module can be linear-converted to a value between -32768 and 32767. Select the
optional range designations and analog I/O data minimum and maximum values by using data registers allocated to analog I/O modules.
3. # When an error is detected, a corresponding error code is sorted to a data register allocated to analog I/O operating status.
Voltage Input Current Input Thermocouple Resistance Thermometer
0 to 10V DC 4 to 20 mA DC
1 MΩ minimum 10Ω 1 MΩ minimum 1 MΩ minimum
—— — 200Ω maximum
—— —1.0 mA maximum
16 msec maximum 50 msec maximum
16 msec maximum 50 msec maximum
32 msec + 1 scan time * 100 msec + 1 scan time *
Single-ended input Differential input
±0.2% of full scale
±0.006% of full scale / °C
4096 increments (12 bits)
2.5 mV 4 µA K: 0.325°C; J: 0.300°C; T: 0.100°C 0.15°C
0 to 4095 (12-bit data); -32768 to 32767 (optional range designation) **
±3% maximum when a 500V clamp voltage is applied to the power and I/O wiring
Common mode reject ratio (CMRR): -50 dB
Twisted pair shielded cable recommended for
improved noise immunity
500V between input and power circuit
Photocoupler between input and internal circuit
13V DC 40 mA DC —
Using software programming
Impossible (approx. 10 years)
Type K (0 to 1300°C)
Type J (0 to 1200°C)
Type T (0 to 400°C)
Self scan
∑∆ type ADC
±0.2% of full scale plus
reference junction compensa-
tion accuracy (±4°C maximum)
±0.5% of full scale
±0.2% of full scale
±1% of full scale
Yes
Detectable #
16V DC
No
—
2 LSB maximum
No damage
Pt 100 3-wire type
(-100 to 500°C)
±0.2% of full scale
Accuracy is not assured when
noise is applied
J
Programmable Logic Controllers
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-23
MicroSmart Series Programmable Logic Controllers
Communication Adapter and Communication Module Specifications (Expansion Modules)
Communication Adapter and Communication Module Specifications
Standards
Maximum Baud Rate
Maintenance Communication
User Communication
Modem Communication
Data Link Communication
Maximum Cable Length
Quantity of Slave Stations
Isolation between Internal Circuit and
Communication Port
Recommended Cable for RS485
Conductor Resistance
Shield Resistance
FC4A-PC1
FC4A-HPC1
EIA RS232C EIA RS485 EIA RS485
19200 bps 19200 bps
Possible Possible Possible
Possible Impossible Impossible
Possible Impossible Impossible
Impossible Impossible Possible
special cable special cable 200m
—— 31
—
— 85 Ω/km maximum
— 20 Ω/km maximum
FC4A-PC2
FC4A-HPC2
Not isolated
FC4A-PC3
FC4A-HPC3
Computer link: 19200 bps
Data link: 38400 bps
Twisted-pair shielded cable with
a minimum core wire of 0.3 mm
2
Optional HMI Module Specifications
Power Voltage
J
Internal Current Draw
Weight
Optional Memory Cartridge Specifications
Memory Type
Accessible Memory Capacity
Hardware for Storing Data
Software for Storing Data
Quantity of Store Programs
Optional Clock Cartridge Specifications
Accuracy
Backup Duration
Approx. 30 days (typical) at 25°C after backup battery fully charged
Battery
Charging Time
Programmable Logic Controllers
Approx. 10 hours for charging from 0% to 90% of full charge
Replaceability
Option Specifications
FC4A-PH1
5V DC (supplied from the CPU module)
200mA DC
20g
FC4A-PM32 FC4A-PM64
EEPROM
32 KB 64 KB
CPU module
WindLDR
One user program can be stored on one memory cartridge
FC4A-PT1
±30 sec/month (typical) at 25°C
Lithium secondary battery
Impossible to replace battery
J-24 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Programmable Logic Controllers MicroSmart Series
I/O Usage Limits
All-in-one Type CPU Modules:
Usage Limits
Input Voltage (V DC)
28.8V
26.4V
Ambient temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
Ambient temperature
45°C
Ambient
temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
Ambient temperature
45°C
Ambient
temperature
55°C
When using at an operating ambient
0 50% 100%
I/O Simultaneous ON Ratio (%)
0 50% 100%
I/O Simultaneous ON Ratio (%)
0 50% 100%
I/O Simultaneous ON Ratio (%)
temperature above 40°C, reduce the
input voltage or the quantity of I/O
points that turn on simultaneously.
Slim Type CPU Modules:
Input Voltage (V DC)
26.4V
24.0V
0 50% 100%
I/O Simultaneous ON Ratio (%)
Ambient temperature
40°C
Ambient
temperature
55°C
Input Voltage (V DC)
26.4V
24.0V
0 50% 100%
I/O Simultaneous ON Ratio (%)
Ambient temperature
55°C
Input Voltage (V DC)
26.4V
24.0V
0 50% 100%
I/O Simultaneous ON Ratio (%)
Ambient temperature
40°C
Ambient
temperature
55°C
Input Usage Limits
Input Voltage (V DC)
28.8V
26.4V
24.0V
0 50% 100%
I/O Simultaneous ON Ratio (%) I/O Simultaneous ON Ratio (%) I/O Simultaneous ON Ratio (%) I/O Simultaneous ON Ratio (%) I/O Simultaneous ON Ratio (%)
Ambient temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
24.0V
0 50% 100%
Ambient temperature
45°C
Ambient
temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
24.0V
0 50% 100%
Ambient temperature
30°C
Ambient
temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
24.0V
0 50% 100%
Ambient temperature
55°C
Input Voltage (V DC)
28.8V
26.4V
24.0V
0 50% 100%
Ambient temperature
45°C
Ambient
temperature
55°C
J
Programmable Logic Controllers
Internal Circuits
Input Internal Circuits
Output Internal Circuit (Slim Type)
SINK OUTPUT
Internal
Circuit
SOURCE OUTPUT
Internal
Circuit
+V
Output
COM(-)
COM(+)
Output
-V
Internal Circuit
Internal Circuit
SLIM TYPE
I0, I1, I6, I7
Input
COM
I2 to I5 and I10 to I27
Input
COM
4.7 kΩ
3.3 kΩ
Internal Circuit
Internal Circuit
ALL-IN-ONE TYPE
I0, I1
Input
COM
I2 to I15
Input
COM
1.8 kΩ
3.3 kΩ
www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC J-27
MicroSmart Series Programmable Logic Controllers
Internal Circuits
Input Internal Circuits (Expansion Modules) Output Internal Circuits
FC4A-N081, FC4A-N16B1
Input
COM
3.3 kΩ
FC4A-N16B3, FC4A-N32B3
Input
COM
4.3 kΩ
FC4A-M08BR1, FC4A-M24BR2
Input
COM
3.3 kΩ
FC4A-N08A11
Internal Circuit
Internal Circuit
Internal Circuit
FC4A-T08K1, FC4A-T16K3, FC4A-T32K3
+V
Internal
Circuit
Output
COM(-)
FC4A-T08S1, FC4A-T16S3, FC4A-T32S3
COM(+)
Internal
Circuit
Output
-V
J
Input
COM
Analog I/O Module
Input Circuit
2 +V1
+V
15 MΩ
NC(A)
+ (B')
-
10 Ω
(B)
Programmable Logic Controllers
1 kΩ
1 kΩ
1 kΩ
-
V1
Input Data
Multiplexer
Input
Selection
Signal
Internal Circuit
Output Circuit
+
-
Output Circuit
J-28 www.idec.com USA: (800) 262-IDEC or (408) 747-0550, Canada: (888) 317-IDEC
Loading...