Ideal Lighting CREE Lighting LN4 User Manual

LN4 Series

LABEL REQUIREMENT FOR END PRODUCT:

The finalendproduct must be labeled in a visible area with the following "Contains TX FCC ID:
2ACQ6-LN4 " and “Contains TX IC ID: 11481A-LN4”

RF Exposure Notice

To comply with the FCC/IC RF exposure compliance

Cree SmartCast™ Technology Wireless Control Module

Includes: LEA02109X0001

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed
including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. CAUTION - risk of shock. Disconnect power before servicing.

ATTENTION - risque de choc. Couper l’alimentation avant l’entretien.

2. Any changes or modications to these devices not explicitly approved by
manufacturer could void your authority to operate this equipment.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TO INSTALL:

STEP 1:

Solder Control Model, LEA02109X0001, into location J67 on
driver board, LEA0261X0001.

STEP 2:

Turn power on. The new control module is correctly installed if
the Blue LED displays a 2 blink sequence.
NOTE: If the blue LED does not respond with the two-blink
sequence, please follow the RESET instructions to return the
control module to factory defaults.

STEP 3:

On the Configuration Tool, select “Replace Devices” from the
“Advanced” menu and follow the on-screen directions.. This
will remove old device(s) from the network.

RESET

NOTE: The Blue LED is located behind the reset button on the

luminaire. The button with illuminate blue when the Blue LED
is active.

STEP 1:

Actuate RESET button. Push and hold (approximately 10 sec),
LED on control module will blink fast.

STEP 2:

Release for 1 sec.

STEP 3:

Press/Hold RESET button for 0.5 sec. Light will go to full
bright and the Blue LED on the control module should be in a
2 blink sequence.

FCC NOTICE

To comply with the FCC RF exposure compliance
requirements, this device and its antenna must not be co­located or operating to conjunction with any other antenna or
transmitter.
This equipment should be installed and operated with
minimum distance 5cm between the radiator & your body. No
other antenna is authorized for use with this product.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment.

This device complies with Part 15 of the FCC Rules. Operation
to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation

This device has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the device is
operated in a commercial environment. This device generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.

The LED in the front of this device operates within Risk Group
1 levels per IEC 62471.

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device. In addition, this device complies with ICES-001 of the
Industry Canada (IC) Regulations.

Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

© 2015 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change.
See www.cree.com/lighting/products/warranty for warranty and specifications. Cree® is a registered
trademark, and the Cree logo is a trademark of Cree, Inc.

1 of 1

www.cree.com/lighting

LPN00303X0001A0_A