IDEAL Krug & Priester 4810-95, 4850-95, 4850-95EP, 5221-95EP, 6550-95EP Operating Instructions Manual

Guillotines GB Operating Instructions

IDEAL 4850-95

IDEAL 4810-95

IDEAL 4850-95EP

IDEAL 5221-95EP IDEAL 6550-95EP

http://www.monomachines.com

http://www.monomachines.com

•

Safety precautions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung

und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit
verfügbar sein.

GB Please read these operating instructions before putting the machine into operation

and observe the safety precautions. The operating instructions must always be
available.

F Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine,

et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation
et les consignes de sécurité doivent toujours être disponibles. Les instructions
d'utilisation et les consi.

NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing

goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en
de veiligheids-voorschriften moeten altijd binnen handbereik zijn.

I Per favore legga questo manuale di istruzione prima di mettere in funzione il

distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono
essere sempre disponibili.

E Le recomendamos lea las instrucciones antes de poner en funcionamiento esta

máquina y cumpla las normas de seguridad. Las instrucciones de servicio y
seguridad deben estar siempre disponibles.

S Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med

säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig.

FIN Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen !

Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla.

N Lees gjennom denne bruksannvisningen før De tar i bruk maskinen

Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen
må alltid være tilgjengelig.

PL Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i

stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być
zawsze dostępne.

RUS Пожалуйста, прочитайте инструкцию по эксплуатации перед установкой

аппарата, соблюдайте технику безопасности. Инструкция по
эксплуатации должна находиться в доступном для пользователя месте.

H A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa

be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie.

TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde

okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý
her zaman kullanýma hazýr olmalýdýr.

DK Før installation af maskinen bedes De venligst læse brugervejledningen

brugervejledningen og være opmærksom på sikkerhedsanvisningerne.
Brugervejledningen skal altid være tilgængelig.

CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní

upozornění. Návod k obsluze musí být vzdy dostupný.

P Por favor leiam o manual de instruções antes de colocar a máquina em operação

e vejam as precauções de segurança. As instruções de operação deverão estar
sempre disponíveis.

GR РБСБКБЛЩ ДЙБВБУФЕ ФЙУ ПДЗГЙЕУ ЧСЗУЕЩУ КБЙ ФЙУ РСПЦХЛБОЕЙУ

БУЦБЛЕЙБУ РСЙН ВБЛЕФЕ ФП МЗЧБНЗМБ УЕ ЛЕЙФПХСГЙБ.
ПЙ ПДЗГЙЕУ ЧСЗУЗУ РСЕРЕЙ НБ ЕЙНБЙ РБНФБ ДЙБИЕУЙМЕУ.

SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila

preden zaženete naparavo. Navodila naj bodo vedno pri roki.

SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do

prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na
dostupnom mieste.

EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige

ohutusnõudeid. Kasutusjuhend peab alati käepärast olema.

CHI

UAE

-2-

http://www.monomachines.com

http://www.monomachines.com

{fJlj~HiliJ

,

~BJJijlJ!t~fFmsl

,

M\lII~3l::i:'<TJl,IJ

tlfF-¥ffl!l?:,~]j~f£*i'if

ffl

~

0

I

Y?-Y

;;01.;>

w~

~I

J;9

0","1

~

¥WIl.S

Iy?-y 4..b.)l.,

w~

:i.,\.!)ICJI.'1I

J

.

WI.l

~I

w~

.ly'-.J

l.JA.l!

';l

•

Safety precautions

•

D Keine Bedienung durch Kinder!

GB Children must not operate the machine!

F Pas d‘utilisation par un enfant!

NL Geen bediening door kinderen!

I Non lasciare utilizzare il tagliacarte a bambini!
E No dejar que la utilicen los niños!
S Installera maskinen utom räckhåll för barn!

FIN Asentakaa laite lasten ulottumattomiin !

N Installer maskinen utenfor rekkevidde for barn!

PL Dzieciom nie wolno obsługiwać urządzenia !

RUS

Не допускайте детей к пользованию аппаратом!

H Gyerekek a gépet nem kezelhetik

TR Makinayý Çocuklar Kullanmamalýdýr.

DK Må kun betjenes af voksne

CZ Stroj nesmí být obsluhován dětmi

P As crianças não devem trabalhar com a máquina!

GR БРБГПСЕХЕФБЙ З ЧСЗУЗ БРП РБЙДЙБ.

SLO Otroci ne smejo uporabljati naprave

SK So strojom nesmú pracovat deti!
EST Lapsed ei tohi masinat kasutada!
CHI
UAE

D Nicht unter das Messer fassen!

GB Do not reach beneath the blade!

F Ne pas passer les mains sous la lame!

NL Niet met de handen onder het mes komen!

I Non toccare la lama nella parte inferiore!
E ¡No tocar debajo de la cuchilla!
S Sträck inte in handen under kniven!

FIN Älä laita kättäsi terän alle !

N Plasser aldri hender ol. under kniven !

PL Nie wkładać rąk pod noże!

RUS

Избегайте попадания рук под лезвие!

H Ne nyúljon a kés alá!

TR

Elinizi býçaðýn altýna sokmayýnýz!

DK Stik ikke hænderne ind under knivbladet!

CZ Nesahejte pod ostří nože!

P Não tocar na parte inferior da faca!

GR МЗН БГГЙЖЕФЕ ФП КБФЩ МЕСПУ ФЗУ ЛЕРЙДБУ!

SLO Ne segajte z roko pod rezilo!

SK Nevkladajte ruky pod nôž!

EST Ärge pange kätt tera alla!

CHI

UAE

- 3 -

http://www.monomachines.com

http://www.monomachines.com

7}]

i1)

L~

~Jf1

fAn!

¥WI

~~.>c

J,ibYI

.)c

...,."..,

1i7}]~~JJ

JHigTJJ

0

~I

u;ti

Ja..~

•

Safety precautions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

D Messer nie lose liegen lassen!

Messer nur mit Messerwechselvorrichtung oder im
Messertransportkasten befördern!
(siehe Seite 33 und 35).

Warnung! Verletzungsgefahr!

GB Never leave the blade unattended!

Do not extract or transport the blade without protection!
(See page 33 and 35).

Danger! Risk of injury!

F Ne jamais laisser la lame sans protections !

Elle ne doit être démontée qu’à l’ aide du dispositif de
changement de lame (cf. page 33 et 35), ou transportée dans
son étui en bois !

Danger! Risques de coupures !

NL Laat nooit de messen alleen achter.

Transporteer de messen niet zonder de houten bescherming
(zie pagina 33 en 35).

Waarschuwing! Opgelet voor ongevallen!

I Non lasciare mai la lama incustodita. Non rimuovere o

trasportare la lama senza protezione. (Vedi pagina 33 e 35).

Attenzione! Rischio di infortunio!

E ¡No quitar la cuchilla sin prestar atención. No desmontar no

transportar la cuchilla sin protección! (vérase pág. 33 y 35)

¡Advertencia! ¡Peligro de hacerse daño!

S Lämna aldrig maskinen obemannad. Ta inte ur eller

transportera kniven utan skydd. (se sid 33 och 35).

Skaderisk!

FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta

terää ilman suojaa ! (katso sivu 33 ja 35

Loukkaantumisen vaara !

N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller

transporter den uten beskyttelse (Se side 33 og 35)

FARE ! Muligheter for skade !

PL Nigdy nie pozostawiać noży bez nadzoru.

Nie wyciągać lub transportować noży bez osłon!
(zobacz strona 33 i 35).

Ryzyko skaleczenia sie!

RUS Не оставляйте открытое лезвие без присмотра! Не

пытайтесь извлечь или транспортировать лезвие без
специальных мер предосторожности!
(См. страницы 33 и 35)

Соблюдайте выше перечисленные правилаСоблюдайте выше перечисленные правила

Соблюдайте выше перечисленные правилаСоблюдайте выше перечисленные правила

Соблюдайте выше перечисленные правила

для избежания травм!для избежания травм!

для избежания травм!для избежания травм!

для избежания травм!

H Soha ne hagyja a kést őrizetlenül!

Ne vegye ki vagy ne szállítsa a kést védőtok nélkül!
(Lásd 33. és 35. oldal)

Veszély! Sérülésveszély!

TR Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz!

Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya
taþýmayýnýz! (Sayfa 33 ve 35’e bakýnýz)

Dikkat! Yaralanma riski!

- 4 -

http://www.monomachines.com

http://www.monomachines.com

•

Safety precautions

•

DK Knivbladet må aldrig efterlades uden opsyn.

Forsøg ikke at afmontere eller transportere knivbladet uden
beskyttelse! (Se side 33 og 35)

FARE! Risiko for legemlig beskadigelse.

CZ Nikdy nenechávejte nůž bez krytu.

Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného
krytu (viz. strany 33 a 35)

Nebezpecí! Riskujete zranení

P Deixar a faca sempre em local seguro!

Não retirar ou transportar a faca sem protecção!
(Ver pág. 33 e 35)

Perigo! Risco de dano!

GR МЗН БЦЗНЕФЕ ФЗН ЛЕРЙДБ БНЕРЙФЗСЗФЗ!

МЗН БЛЛБЖЕФЕ ¹ МЕФБЦЕСЕФЕ ФЗН ЛЕРЙДБ ЧЩСЙУ
РСПЦХЛБОЗ (ДеЯфе учефйкЬ уфйт уелЯдет 33 & 35)

РСПУПЧЗ ! КЙНДХНПУ ФСБХМБФЙУМПХ !

SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte

rezilo brez zaščite. ( glej stran 33 in 35).

Pozor!Pozor!

Pozor!Pozor!

Pozor!

Nevarnost poškodbe.Nevarnost poškodbe.

Nevarnost poškodbe.Nevarnost poškodbe.

Nevarnost poškodbe.

SK Nenechávajte nôž nechránený (nezabezpecený)!

Nevyberajte alebo netransportujte nôž bez ochrany
(vid s. 33 a 35)

! Riziko úrazu !! Riziko úrazu !

! Riziko úrazu !! Riziko úrazu !

! Riziko úrazu !

EST Ärge jätke lõiketera kunagi järelevalveta!

Ärge pikendage ega teisaldage tera kaitseseadmeteta!
(Vt lk 33 ja 35)

Oht! Vigastuste oht!

CHI

UAE

33

35

35

33

- 5 -

http://www.monomachines.com

http://www.monomachines.com

~~AW.~.~T,.~.ffn

•.

~)9:1'l~:t?~'~)JtT

,

.~IllU:i:ls&@.!n.

!

(~Im~

27

*028

:vf).

fB~!"iiJsl~5!t11.i

!

I'w",) UJ.i!

~I

~ji:i

'l

.

(28J27

~

,;hi!)

=4b

UJ.i!,

~I

JiJJ

JI

t:::y..:i

'l

<.S

j)lj

~

y..:ill

!

y,.:;..

•

Safety precautions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

D Keine harten und splitternden Materialien schneiden!

GB Do not cut hard materials or materials which may splinter!

F La coupe de matériaux trop durs ou risquant des projections

est interdite !

NL Snij geen harde materialen of materiaal dat kan splinteren!

I Utilizzare il tagliacarte esclusivamente per il taglio di risme

di carta o materiali analoghi!

E ¡No cortar materiales duros o materiales que puedan

astillarse!

S Förstör inte hârt material eller material som kan splittras!

FIN Asentakaa laite lasten ulottumattomiin !

N Ikke kutt hardt metall eller materiale som kan splintre !

PL Nie ciąć twardych materiałów lub materiałów, które mogą

ulec odpryśnięciu!

RUS

Данный резак не предназначен для резки твердых
материалов или материалов, которые могут
расщепляться!

H Ne vágjon kemény vagy olyan anyagot, amely repedhet!

TR Sert veya parçalanabilecek malzemeleri kesmeyiniz!

DK Der må ikke skæres i hårde materialer eller i materialer, der

kan splintre!

CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré

úlomky!

P Não cortar materiais duros ou materiais que possam lascar!

GR МЗН КПВЕФЕ УКЛЗСБ ХЛЙКБ ¹ ХЛЙКБ РПХ

ИСХММБФЙЖПНФБЙ!

SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko

razcepijo.

SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu

vystrelovat ostré úlomky.

EST Ärge lõigake kõvasid materjale ega materjale, mis võivad

pilbasteks puruneda!

CHI
UAE

- 6 -

http://www.monomachines.com

http://www.monomachines.com

m?}]tJ]~J~li!~"llJ~PXl#h![e-mail]

!y~~Y-~

,;;JI

.~YI

-,1

~I

.~YI

~

'J

•

Safety precautions

•



The machine is designed for cutting stacks of
paper to a specified size.
This machine is constructed for "one-man
operation" only!

Warning! Clips or similar damage the

cutting blade.



Disconnect from the mains before starting any

service work or before removing the panels!

Replacement of blade and cutting stick may
be performed only when the main switch is
switched off!

- 7 -

http://www.monomachines.com

http://www.monomachines.com

•

Safety precautions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

All components which could endanger the
operator are covered by a guard!

A

A

A



B

C

A

C



Operating the machine without safety device is
forbidden!
(Front safety guard (A), rear screwed safety
guard (B) and panel (C).

- 8 -

http://www.monomachines.com

http://www.monomachines.com





•

Safety precautions

•

The dangerous cutting movement is
safeguarded by a movable guard (A) and a
safety two-handed control system! (B)

B

A

Before working with the machine and after
every blade replacement the automatic cut-off
function of safety guard (A),(correct if distance
between cover and table is < 20 mm) main
switch (B) and control panel (C) must be
checked.

C

- 9 -

http://www.monomachines.com

http://www.monomachines.com





•

Safety precautions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Protect mains cable against heat, oil and

sharp edges!

Connect the power cord to a single phase
socket.

230V / 10A min
115V / 15A min

Ensure free access to mains!

- 10 -

http://www.monomachines.com

http://www.monomachines.com

•

Safety precautions

•

When not in use for a longer period switch off.

(Main switch to "0").

OK

Clamping

Blade

OK

- 11 -

http://www.monomachines.com

http://www.monomachines.com

•

Installation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Only IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 6550-95EP

Remove the stand from the wooden pallet.

B



C

A

4 x

Only IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 6550-95EP

4 strong people are required to lift the machine
from the pallet and place it on the stand.
Secure with 4 screws (A). Put the shelf (B) on
the stand. (Parts and tools are in the tool set
(C).

- 12 -

http://www.monomachines.com

http://www.monomachines.com





•

Installation

•

IDEAL 5221-95EP

The machine is delivered ready for operation.
4 strong people are required to lift the
machine from the pallet.

C

A

Side tables, left and right, (A) are available
as accessories.
Attach the side tables to the front table so
that the upper surface is level.
(Screws and nuts are in a plastic bag in the
tool set (C).
The front and rear wooden panels must be
removed for in-house transport on a pallet
truck.
For transport through narrow doors:

•

Remove side tables

•

Remove the machine from its base
(4 screws)

•

Tilt the machine on its side

•

Mount the machine to its base

•

Screw on all side panels

Only IDEAL 4810-95, IDEAL 4850-95

Tighten the backgauge crank (A). Parts and
tools are in the tool set (C).

A

C

- 13 -

http://www.monomachines.com

http://www.monomachines.com

•

Installation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Only IDEAL 4810-95

Attach the enclosed hand-wheel for clamping.
Parts and tools are in the tool set (C).



C



Plug into socket.
The machine must be connected directly to the
socket.

- 14 -

http://www.monomachines.com

http://www.monomachines.com







•

Operation

•

It is forbidden to operate the machine if the

A

operating and safety instructions have not been
understood. Please check the safety devices
are functioning and complete before use.

•

All covers have to be mounted (A).

•

The release for cutting is allowed only if
the cover is closed and the two-hand safety
device is operated at the same time (B)

•

If the front cover closes by itself the
gas spring (X) needs replacing.

We recommend you keep a record of your test
results.

A

A

B

B

X

- 15 -

http://www.monomachines.com

http://www.monomachines.com

C



•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

D

A

B

Position the main switch to "I" (A). Insert the
key for the control system and move it to the
right (B). Open the safety guard (C). The
machine is now ready for use.

Only IDEAL 4850-95EP, IDEAL 5221-95EP,

IDEAL 6550-95EP

Press

S

button (D).

Machine will automatically go to the start

position.



IDEAL 4850-95EP, IDEAL 5221-95EP,

IDEAL 6550-95EP

B

The measurement is set either with the hand­wheel (A) or by programming (B) the cutting
measurements. Measurement is shown on the
display in inches or cm (B).

A

- 16 -

http://www.monomachines.com

http://www.monomachines.com



•

Operation

•

B

A

C

D

E

A

B

C

IDEAL 4810-95, IDEAL 4850-95

The measurement is set with the backgauge
crank.(A) The symbol – rotary direction –

moves to the right on the display (B) (see
picture C). The rotary direction of the
backgauge crank (A) is indicated on the right.
Keep turning the backgauge crank to the right
until a measurement appears (see picture E).
The reference position is reached.
The cutting size can now be set with the
handle (A).
If the backgauge is right at the front the
symbol – rotary direction – will move to the
left (see picture D). Turn the backgauge crank
to the left until the rotary direction appears on
the right in the display (see picture C).
Afterwards turn the backgauge crank to the
right until a measurements appears (see
picture E). The reference position is reached.
The cutting size can now be set with the
handle (A).

Measurement is shown on the display in
inches or cm (B).

IDEAL 4810-95
If display (C) shows "

AB " the clamp must be

completely opened.
Turn the hand-wheel for clamping (A)
completely to the left until the backgauge (B)
is activated.

- 17 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Optical cutting line (A) that indicates the exact

A

position of the cut. Blade cuts on the front
edge (B) of the light beam. (Only use when no
exact cut is required).



B



Only IDEAL 4810-95, IDEAL4850-95.

Pull out the handle to avoid the measurement
being wrongly adjusted.

- 18 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•



B

A

B

C

Position the paper on the backgauge (A) and
side lays left or right (B).
To move paper stacks, please use the paper
knock-up block (C) provided.
(Run backgauge to the front for turning the
paper stack).

- 19 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP



IDEAL 4850-95/EP, IDEAL 5221-95EP

IDEAL 6550-95/EP

The clamp moves automatically when cutting
is activated.

The paper can also be pressed in advance.
Clamping and cutting is activated by
pressing button (A) on the front table.

A

=

Pre-clamping

+

+ =

Clamp returns

+ =

Cutting sequence with automatic clamping



Only 4810-95

Clamping is released by the hand-wheel.
Before every cut lower the clamp by turning the
hand-wheel to the right and tighten with a light
twist. The cut is activated by pressing the two
buttons exactly at the same time.

- 20 -

http://www.monomachines.com

http://www.monomachines.com

:dJ.~

:dJ

::!J





•

Operation

•

Close the safety guard.

Cutting activation:

Press both buttons of the two-handed control
system activation (A) simultaneously and them
pressed until the paper is completely cut.

To interrupt or stop cutting:

To interrupt or stop cutting, release
both buttons (A) of the two-hand control.

- 21 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Nur bei IDEAL 4850-95/EP,
IDEAL 5221-95/EP, IDEAL 6550-95/EP

Nur bei IDEAL 4810-95, IDEAL 4850-95

Operating elements

A

- Front safety guard

B

- Safety two-handed control system
Pre-clamping and cutting

C

- Overload switch
(blade drive/clamp drive/
backgauge drive)

D

- Backgauge control (EP)

E

- Paper clamp
(only IDEAL 4810-95)

F

- Main switch

G

- Hand-wheel (EP) or crank handle
for backgauge setting

H

- Key switch

I

- Backgauge

J

- Side lay left and right

K

- Display cutting size (EP, cm or inch)

L

- Select program step up (Programming)
or fixed dimension (Standard 21 cm)

M

- Select program step down (Programming)
or fixed dimension (Standard 10,5 cm)

N

- Stop and delete input

O

- Start

P

- Memory multiple cut

Q

- Keypad

R

- Changeover cm - inch (LED - display)

S

- Clear program

T

- Select program

U

- Enter

V

- Program number

W

- Program step

X - Cut is blocked
Y - Display multiple cut
Z - Display cutting size (cm or inch)
a - Changeover cm/inch
b - Measuring unit (cm or inch)

- 22 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95, IDEAL 4850-95

B

A

C

D

E

IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 5221-95EP, IDEAL 6550-95EP
Start machine

•

Main switch F to position "I", insert the key

H

for the control panel and turn it to the right.

Open the front safety guard

A

Only by IDEAL 4810-95, IDEAL 4850-95
Cutting to specified dimensions

•

The measurement is set with the backgauge
crank.(A) The symbol – rotary direction –
moves to the right on the display (B) (see
picture C). The rotary direction of the
(backgauge crank (A) is indicated on the
right. Keep turning the backgauge crank to
the right until a measurement appears
(see picture E).
The reference position is reached. The
cutting size can now be set with the
handle (A).
If the backgauge is right at the front the
symbol – rotary direction – ill move to
the left (see picture D). Turn the backgauge
crank to the left until the rotary direction
appears on the right in the display (see
picture C). Afterwards turn the backgauge
crank to the right until a measurements
appears (see picture E). The reference
position is reached. The cutting size can now
be set with the handle (A).
The measurement scale in cm or inch has a
LED display

a

. For information on how to

store see page 22, picture below left.

•

Insert paper and move by means of the
stacking angle to the backgauge I and side
lay on the left

J

.

Turn the hand-wheel

E

for paper clamping to

the right and tighten with a short twist.

•

Close the front safety guard

A.

•

Release the cut.

Cut according to markings

•

Adjust the backgauge with the crank handle

G

to the back.

•

Insert paper and move by means of the
stacking angle to the backgauge

I

and side

lay on the left

J.

•

Turn the crank handle G to the right until the
marking on the paper to be cut is below the
cutting line indicator.

- 23 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

IDEAL 4850-95EP,
IDEAL 5221-95EP, IDEAL 6550-95EP
Start machine

•

Main switch F to position "I", insert the key

H

for the control panel and turn it to the right.

Open the front safety guard

A

• Press

S

button O  backgauge I moves
to the rear and searches for the reference
position, wait until a measurement
is shown in the display

D.

IDEAL 4850-95/EP = 45 cm, 17,72 inches
IDEAL 5221-95EP = 52 cm, 20,47 inches
IDEAL 6550-95/EP = 61 cm, 24,02 inches

Warning!

Before storing or cutting a measurement
please check if the correct measurement
scale (cm or inch) see above is stored.
For information on how to store see picture
below left.

Cutting to specified dimensions

•

Enter dimension on the numerical key pad

Q

 LED "S" X appears.
(If a wrong dimension is entered this can be
corrected by pressing the s button).

•

Press S button  dimension is
approached,  LED "S" disappears.
Dimensions below 9 cm  3,5 cm (IDEAL
6550-95EP 2,5 cm) can only be approached
with the

S

button pressed and held. (When

the S button O is released, the backgauge

I

moves to a measurement of 9 cm 
measurement 9 cm blinks, keep
the S button pressed, backgauge I moves
to e.g. 7 cm.

•

Insert paper and move by means of the
stacking angle to the backgauge I and side
lay on the left

J

.

•

Close the front safety guard

A.

•

Release the cut.

Cut according to markings

•

Adjust the backgauge with the hand-wheel

G

to the back.

•

Insert paper and move by means of the
stacking angle to the backgauge I and side
lay on the left

J.

•

Turn the hand-wheel G to the right until the
marking on the paper to be cut is below the
cutting line indicator.

Only EP machines.

•

The further the hand-wheel

G

is turned to the right, the quicker the

backgauge moves. If the hand-wheel is
turned to the left the backgauge will return
quicker.

- 24 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

Eject function

If button

j M

is pressed instead of button

S O

,

after inserting the measurement

Q

, the
backgauge will advance forwards so that
paper can be removed. Finally the backgauge
moves to the last setting.

Adjust the eject-dimension

• Press p, hold, and press T e on

display.

• Insert the desired dimension.

(Standard is 20 cm).

• g Store dimension.

•

p

+ sEscape the program mode.

Program buttons b and

j

programs

Press

p

, hold, and press

b (ö

appears on
the display) or
Press

p

, hold, and press

j (Ü

appears

on the display)

• Enter the desired dimension (For example:

29,7 cm x 21 cm can be entered for DIN A4)

•

g

Store dimension.

Display in cm or inch

• Press

i

 display changes between cm

and inch (see page 22 and 24).

Cutting activation

Warning!

• Run backgauge to the front for turning the

paper stack.

• Do not interrupt the upward movement of the

blade by performing switching procedures.

• Release blade only when LED "S"

X

has gone

out.

• Close the front safety guard A.

• Blade must always be at the top and be

covered by the clamp. Do not touch the
blade.
(see safety information on page 38).

Risk of injury!

Multiple cut

•

Enter the multiple cut size on the display Q.

•

Advance to the measurement with the

S

button.

•

Push the paper to the backgauge I.

•

Press T button  the red LED "M " Y light
will be on.

•

Enter the multiple cut size.

•

After cutting has been activated press

S

button.
Every time the

S

button is pressed, the
backgauge will advance by the multiple cut
size.

•

Pressing the s button N shows the actual
size.

Exiting program-mode

•

Pree

T

button  LED "M " Y is cleared on

the display.

- 25 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Programming
Only IDEAL 4850-95EP, IDEAL 5221-95EP,
DEAL 6550-95EP

This control system enables you to store 99
programs with 99 programmable steps. One
step represents one measurement. After
entering the program numbers you are able to
change between several program steps with
the button

j

and b .
First figure on display = program number.
Second figure = program step.
Dimensions below 9 cm/3,54 inch can only
be approached with the

S

button held pressed.

"

u" on the display  the entered dimension is

too low.
"

o" on the display  the entered dimension is

too high.
Each program step corresponds to one
dimension. The indicated program step can be
overwritten at any time. These programs
remain stored when the machine is off. Should
you change to another dimension unit all
programmed measurements are converted into
the new unit (cm or inch).

Entering a program

• Press

p

 P appears on the display.

•

01

...

99

Enter program number 01 ... 99.

(Top number V on display = program number).

• If measurement is shown on the display

K

the

program is reserved.

•

Enter dimension, or move the backgauge to
the desired measurement with the

hand-wheel

G

.

•

g

Store the dimension  next program step

appears W.

•

Enter the next dimension.
Should an ejection be desired before this cut
press

p

, hold, and press T.

•

g

Store the dimension  next program step

appears.

•

Should the entered program be required
immediately  press

S

(program is closed).
Press Sagain (backgauge moves to the
dimension of the first program).

Or:

•

p

+ s Escape the program mode.

- 26 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

Eject function program

The eject function can be added each time a
measurement is entered and ejects before
advancing to the next measurement.
An eject at the end of a program must be
programmed in the first step at the program.
If the dimension and eject function are stored in
the program step the program number appears
on the display

V

.

Example of a program eject function

•

p 0 8

program 08

•

c c

delete previous program

•

1 6 g

step 1 on 16,0 cm

•

2 0

step 2 on 20,0 cm

• Press

p

, hold, and press T eject (e blinks)

•

g

Store the dimension

•

p s

escape the program mode

How the example works

•

p 0 8

start program 08

•

S

proceeds to position

• Insert paper

• Release cut 1

• Press

S

button

• Paper is ejected (

V

blinks)

• Turn the paper

• Release cut 2

•

p s

escape the program mode

Programming of multiple cut dimension

•

p

Press  "X" appears on the display.

•

0 1

...

9 9

Enter program number 01 ... 99.
Top number on display = program number.
Lower number = program step.

•

Enter the cut size on the display Q.

• g

Store the dimension.

• Enter multiple cut size.

Press

T

button E W and multiple cut size

appears on the display.
Press

T

button again F ..... N.

•

g

Store the dimension.

•

p

+ s Escape the program mode.

Maximum nine multiple cuts can be entered.

- 27 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Cancel a program

•

p

press  "X" appears on the display.

•

0 1

...

9 9

Enter program number 01 ... 99.

• Press button

c

twice.

Each program has to be cancelled separately.

Deleting a dimension when programming

Press

s

and overwrite the dimension.

Choose a program step appears.

Press

p

, hold, and press T 

ß W

lights.

Enter the desired number of steps (e.g.

0 5

).

Change a step

b

 next step

j

 previous step

Insert a step

Press

p

, hold, and press b  A new
program step is inserted before the displayed
program step is shown.

Delete a step

Press

p

, hold, and press j  Program step
is deleted.
The following number of steps are updated.

- 28 -

http://www.monomachines.com

http://www.monomachines.com

•

Operation

•

Working with programs

• Press

p

 "X" appears on the display

•

01

...

99

Enter program number 01 ... 99

With the button

j

and b you are able to

change between several program steps.
With

S

the backgauge moves to the indicated

dimension.
With

s

the backgauge stops.

General

LED "S" lights  Cut is blocked.
LED "S" is off  the actual dimension appears.
In the program mode the ejection of paper

j

is not possible. The ejection of paper has to
be programmed.

Escape the program mode

• Press

p

 "X" appears on the display.

• Press

s

 escape the program mode.

- 29 -

http://www.monomachines.com

http://www.monomachines.com

•

Blade and cutting stick replacement

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

If the cutting quality decreases:

•

Check the cutting depth (see page 38).

•

Check the cutting stick (see page 34).

•

Replace or grind the blade (see page
30 - 38).

The blade cannot be ground if the blade
height is less than 83 mm/3,29 inches.
A new blade must be used.

The blade may only be ground by a qualified
supplier or from the manufacturer
Krug & Priester, D-72336 Balingen.

Danger! Risk of injury!
The blade is extremely sharp. Do not
extract or transport the blade without
protection. Changing the blade may only be
performed by trained staff.

- 30 -

http://www.monomachines.com

http://www.monomachines.com

•

Blade and cutting stick replacement

•

Turn the blade depth adjustment screw to the

left until it stops. (Screwdriver found in tool set
(A).

Close the safety guard (1.).
Lower the blade by pressing both cutting
buttons (2.). Keep one button pressed and
turn off the main switch (3.).

- 31 -

http://www.monomachines.com

http://www.monomachines.com





•

Blade and cutting stick replacement

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

The 3 eccentrics are now exposed and should

C

A

B

be turned counter clockwise to position "0"
with the special wrench and attachable
extension pipe (A) (in the tool set). The slot
must correspond to position "0" (B).

Only IDEAL 4810-95, 4850-95/EP

Unscrew the blade screws (C) on the right
hand side.

OK

Clamping

Blade

OK

- 32 -

http://www.monomachines.com

http://www.monomachines.com



•

Blade and cutting stick replacement

•

A

3.

2.

1.

1.

A

3.

Position the main switch to "0" (1.)
Remove the 2 blade screws on the elongated
holes (2.). Then put the blade changing tool (A)
into place and fasten it to the blade (3.).

Remove 2 blade screws (1.)
IDEAL 4810-95, IDEAL 4850-95/EP
and 3 blade screws (1.) IDEAL 5221-95EP,
IDEAL 6550-95EP.
Loosen the grips (2.) of the blade changing
tool (A) lightly and allow the blade to be taken
downwards out of the machine (3.). Place the
blade into the blade carrier (B) and screw it
into place (4).

B

2.

4.

- 33 -

http://www.monomachines.com

http://www.monomachines.com

•

Blade and cutting stick replacement

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Take out the cutting stick with a small screw­driver. If needed the cutting stick can be turned
or exchanged. (The cutting stick can be used
eight times).



- 34 -

http://www.monomachines.com

http://www.monomachines.com

•

Blade and cutting stick replacement

•

A

11 mm

0.43 inch

B

B

C

C

Place the blade to be exchanged with the
blade changing tool (A) mounted (1.), into the
blade carrier and push it up to the top and
screw it into place with the grips (2.).

A

1.

2.

- 35 -

http://www.monomachines.com

http://www.monomachines.com





•

Blade and cutting stick replacement

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

1.

Lightly tighten 3 (IDEAL 4810-95,
IDEAL 4850-95/EP has 2) of the 5 blade
screws with washers (1.). Remove the blade

A

changing tool (2.). Lightly tighten the
remaining blade screws with washers (3.).

2.

IDEAL 4810-95 and IDEAL 4850-95/EP

Lightly screw in the right blade screw with the
washer (A) when the blade is lowered.

3.

Remove all tools and distribute paper along
the entire cutting length (1.).
Turn main switch to position "I" (2.).

1.

2.

- 36 -

http://www.monomachines.com

http://www.monomachines.com



•

Blade and cutting stick replacement

•

Close the safety guard (1.) Lower the blade by

1.

pressing both cutting buttons (2.). Keep one
button pressed and turn off the main switch (3.).

3.

2.

4.

A

5.

A

2.

Open the safety guard (4.). With the special
wrench (B) the 3 eccentrics should be screwed
down (5.)until the paper is cut along the
entire length of the blade (The blade must
remain parallel, not too deep into cutting stick).

Only IDEAL 4810-95 and
IDEAL 4850-95/EP

Tighten the blade screws (A) on the right hand
side.

Turn main switch to position "I" (1.). Blade will
return to upper position. Tighten the blade
screws (2.) firmly.

Warning by IDEAL 4810-95

Do not turn main switch to position
"0" whilst blade is moving upwards! The
clamp must always overlap the blade!
(see page 38).

Danger! Risk of injury!

1.

- 37 -

http://www.monomachines.com

http://www.monomachines.com

•

Blade and cutting stick replacement

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP



A

Paper cutting test. If the last sheet or several
sheets are not completely cut, gradually turn
the knob for blade depth adjustment (A)
¼ turn to the right until the paper is cut along
the entire length. Do not set too low as blade
will become blunt sooner.

Warning by IDEAL 4810-95

Danger!
Blade must always be covered by the
pressing bar (see picture below at the left).

OK

Clamping

Blade

OK

- 38 -

http://www.monomachines.com

http://www.monomachines.com



•

Maintenance and cleaning

•

Maintenance work may only be performed by
trained staff.

Danger! Disconnect the mains before
starting any service work or before
removing the cover.

D

Grease the backgauge (A) control weekly with

a grease gun. Advance the backgauge as far
as possible to the front. (Use non-resinous oil
or grease).

Grease the remaining parts twice a year (see

picture).

The main switch must be on "0" (B).
Remove lower panel and rear wooden panel

(C). Tools in tool set.

• Remove any paper.

• Grease the machine.

• Check the 4 joining bolts and 2 pushing bars

for wear (D). If necessary inform your service
personnel.

• Mount the machine.

= Greasing points on the machine.

- 39 -

http://www.monomachines.com

http://www.monomachines.com

•

Maintenance and cleaning

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Safety test

The safety regulations are according to the
regulations of the country where the cutting
machine is operated. The manufacturer
recommends a safety check is made every 5
years by an authorised service team.

- 40 -

http://www.monomachines.com

http://www.monomachines.com

•

Possible malfuntions

•

Machine does not function!



Is the machine plugged in?

Main switch to position "I"? (A)

Control system activated? (B)
(Turn key to the right)
Release a cut see page 21.

- 41 -

http://www.monomachines.com

http://www.monomachines.com

•

Possible malfuntions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Cut cannot be made.

•

If cover is open:

close it.

•

If cover is closed:

open and re-close it. (Security check).



- 42 -

http://www.monomachines.com

http://www.monomachines.com

•

Possible malfuntions

•



A, B

Machine turns off:

•

Machine overloaded.
Safety button (A) ejects.
(Allow 1 minute cooling time and reset the
safety button (A).

•

Machine blocked.

•

Blade is blunt.
Eliminate the cause, and push the safety
button (A).

Only IDEAL 4850-95EP,

IDEAL 5221-95EP, IDEAL 6550-95EP

•

Backgauge blocked
Safety button (B) ejects.
Eliminate the cause, and push the safety
button (B).

Safety button for:

A =

Blade drive

A =

Clamping drive

B =

Backgauge drive

- 43 -

http://www.monomachines.com

http://www.monomachines.com

•

Possible malfuntions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

B





A

Does not cut through the last sheet:

•

Turn or turn around the cutting stick (A),
readjust the blade by means of the blade
adjusting knob (B)
(see page 38).

Poor cutting quality or blade stays in the
paper stack.

•

Change the blade (C) (see pages 30 - 38.

- 44 -

C

http://www.monomachines.com

http://www.monomachines.com

•

Possible malfuntions

•

Motor runs but blade does not move

downwards.

•

Security brake has been activated!
Inform the Service Team!

•

www.ideal.de  "Service"
[e-mail]



C

B

A

Display illumination off

•

Machine is plugged in? (A)

•

Main switch on position "I"? (B)

•

Push in the safety button! (C)

•

Check the units fuse and the on-site circuit
breaker!

- 45 -

http://www.monomachines.com

http://www.monomachines.com



•

Possible malfuntions

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

IDEAL 4850-95EP, IDEAL 5221-95EP,

IDEAL 6550-95EP

Cut cannot be made.

•

Measurement has not been reached
correctly.

•

LED "S" X does not turn off.

Push the

SS

SS

S

button again.

Check the security cover (see page 42).

•

Measurement below 9 cm/3,54 inch

Hold the

SS

SS

S

button O until the

measurement is achieved.

•

Backgauge

I

does not move and "AB "

is shown on the display.

..

..

.

Open the clamp

E

Turn the hand wheel to the left as far as
possible.

•

Backgauge I does not advance to position

(Hand-wheel has been turned to the left).
"

AB " is shown on the display.

 inform service people.

None of the above mentioned methods

helped to solve the problem:

Contact Service Team under

•

www.ideal.de  "Service"
[e-mail]

- 46 -

http://www.monomachines.com

http://www.monomachines.com

•

Accessories

•

Recommended accessories:

Blade

•

Nr. 9000 021 IDEAL 4810-95

•

Nr. 9000 021 IDEAL 4850-95/EP

•

Nr. 9000 130 IDEAL 5221-95EP

•

Nr. 9000 025 IDEAL 6550-95/EP

Cutting stick (6 pieces)

•

Nr. 9000 022 IDEAL 4810-95

•

Nr. 9000 022 IDEAL 4850-95/EP

•

Nr. 9000 024 IDEAL 5221-95EP

•

Nr. 9000 026 IDEAL 6550-95/EP

Blade changing tool

1

•

Nr. 9000 518 IDEAL 4810-95

•

Nr. 9000 518 IDEAL 4850-95/EP

•

Nr. 9000 512 IDEAL 5221-95EP

•

Nr. 9000 513 IDEAL 6550-95/EP

Paper knock-up block

1

•

Nr. 9000 521 IDEAL 4810-95

•

Nr. 9000 521 IDEAL 4850-95/EP

•

Nr. 9000 521 IDEAL 5221-95EP

•

Nr. 9000 521 IDEAL 6550-95/EP

Side tables left and right

•

Nr. 9000 530 IDEAL 5221-95EP

1

Included in delivery

- 47 -

http://www.monomachines.com

http://www.monomachines.com

•

Technical data

•

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

Technical data:

•

Power supply: 230V/50Hz/1~,120V/60Hz/1~

•

Cutting height: 80 mm

•

Sound level EN 13023: < 70 dB (A)

•

Leakage current < 3,5mA

•

Power cord gauge min. 1,5mm2 (230V).

•

Power cord gauge AWG 14 (15A) (120V)
(IDEAL 4810-95)

•

Power cord gauge AWG 12 (20A) (120V)
(IDEAL 4850-95, 4850-95EP, 6650-95 EP)

The exact technical specifications can be
found on the technical specifications sticker (A)
on the machine. A wiring diagram is found in
the electrical switch box.
To claim under guarantee, the machine must
still carry its original identification label.



A

Cutting-

length

mm

Table-

depth

mm

Minimum space

requirement

(B X T X H) mm

Weight

kg

IDEAL 4810-95 475 458 755 x 970 x 1360 194
IDEAL 4850-95 475 458 755 x 970 x 1230 209
IDEAL 4850-95 EP 475 450 755 x 970 x 1230 215
IDEAL 5221-95 EP 520 520 855* x 1067 x 1260 262**
IDEAL 6550-95 EP 650 610 995 x 1260 x 1220 304

* with side tables: 1560 mm
** with side tables: 276 kg

- 48 -

http://www.monomachines.com

http://www.monomachines.com

•

Technical data

•

This machine is approved by independent
safety laboratories and is in compliance with
the EC-regulations 98/37/EG, 2006/95/EG and
2004/108/EG.

Sound level information:

The sound level is < 70 db (A) as defined by
EN 13023.

Subject to alteration without notice.

- 49 -

http://www.monomachines.com

http://www.monomachines.com

~

(~\

ISO

9001

IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP

D EG-KONFORMITÄTSERKLÄRUNG

GB EC-declaration of conformity

F Déclaration de conformité CE

NL EG-verklaring van overeenstemming

I Dichiarazione CE di conformità
E Declaración CE de conformidad

- Hiermit erklären wir, daß die Bauart von

- Herewith we declare that

- Par la présente, nous déclarons que

- Hiermede verklaren wij, dat de in de handel gebrachte machine

- Si dichiara che il modello della

- Por la presente, declaramos que la

4850-95 EP: 5221-95 EP; 6550-95 EP:
4810-95; 4850-95.

- folgenden einschlägigen Bestimmungen entspricht

- complies with the following provisons applying to it

- sont conformes aux dispositions pertinentes suivantes

- voldoet aan de eisen van de in het vervolg genoemde bepalingen

- è conforme alle seguenti disposizioni pertinenti

- satisface las disposiciones pertinentes siguientes

98/37/EG; 2006/95/EG; 2004/108/EG.

- Angewendete harmonisierte Normen insbesondere

- Applied harmonised standards in particular

- Normes harmonisées utilisées, notamment

- Gebruikte geharmoniseerde normen, in het bijzondere

- Norme armonizzate applicate in particolare

- Normas armonizadas utilizadas particularmente

EN 60204-1; EN 1010-1; EN 1010-3;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3;
EN ISO 12100-1; EN ISO 12100-2; EN ISO 13857; EN 954-1; EN 13023;
EN ISO 11204

Krug & Priester GmbH u. Co KG 01.08.2008

72336 Balingen, Germany Datum

Wolfgang Priester

- General Manager -

- 50 -

http://www.monomachines.com

http://www.monomachines.com

Remarks:

- 51 -

http://www.monomachines.com

http://www.monomachines.com

IDEAL • Made in Germany

Document Shredders

Trimmers and Guillotines

•

IDEAL Krug & Priester

•

72336 Balingen

•

Germany

•

www.ideal.de

•

Printed in Germany • IDEAL 06/2009

http://www.monomachines.com

http://www.monomachines.com