IDEAL 4815
IDEAL 4850
GB Operating InstructionsGuillotines
www.WhitakerBrothers.com
IDEAL 4815 • IDEAL 4850
- 2-
D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung
und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit
verfügbar sein.
GB Please read these operating instructions before putting the machine into operation
and observe the safety precautions. The operating instructions must always be
available.
F Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine,
et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation
et les consignes de sécurité doivent toujours être disponibles. Les instructions
d'utilisation et les consi.
NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing
goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en
de veiligheids-voorschriften moeten altijd binnen handbereik zijn.
I Per favore legga questo manuale di istruzione prima di mettere in funzione il
distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono
essere sempre disponibili.
E Le recomendamos lea las instrucciones antes de poner en funcionamiento esta
máquina y cumpla las normas de seguridad. Las instrucciones de servicio y
seguridad deben estar siempre disponibles.
S Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med
säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig.
FIN Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen !
Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla.
N Lees gjennom denne bruksannvisningen før De tar i bruk maskinen
Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen
må alltid være tilgjengelig.
PL Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i
stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być
zawsze dostępne.
RUS Пожалуйста, прочитайте инструкцию по эксплуатации перед установкой
аппарата, соблюдайте технику безопасности. Инструкция по
эксплуатации должна находиться в доступном для пользователя месте.
H A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa
be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie.
TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde
okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý
her zaman kullanýma hazýr olmalýdýr.
DK Før installation af maskinen bedes De venligst læse brugervejledningen
og være opmærksom på sikkerhedsanvisningerne. Brugervejledningen
skal altid være tilgængelig.
CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní
upozornění. Návod k obsluze musí být vždy dostupný.
P Por favor leiam o manual de instruções antes de colocar a máquina em operação
e vejam as precauções de segurança. As instruções de operação deverão estar
sempre disponíveis.
GR РБСБКБЛЩ ДЙБВБУФЕ ФЙУ ПДЗГЙЕУ ЧСЗУЕЩУ КБЙ ФЙУ РСПЦХЛБОЕЙУ
БУЦБЛЕЙБУ РСЙН ВБЛЕФЕ ФП МЗЧБНЗМБ УЕ ЛЕЙФПХСГЙБ.
ПЙ ПДЗГЙЕУ ЧСЗУЗУ РСЕРЕЙ НБ ЕЙНБЙ РБНФБ ДЙБИЕУЙМЕУ.
SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila
preden zaženete naparavo. Navodila naj bodo vedno pri roki.
SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do
prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na
dostupnom mieste.
EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige
ohutusnõudeid. Kasutusjuhend peab alati käepärast olema.
CHI
UAE
•
Safety precautions
•
- 3 -
D Keine Bedienung durch Kinder!
GB Children must not operate the machine!
F Pas d‘utilisation par un enfant!
NL Geen bediening door kinderen!
I Non lasciare utilizzare il tagliacarte a bambini!
E No dejar que la utilicen los niños!
S Installera maskinen utom räckhåll för barn!
FIN Asentakaa laite lasten ulottumattomiin !
N Installer maskinen utenfor rekkevidde for barn!
PL Dzieciom nie wolno obsługiwać urządzenia !
RUS
Не допускайте детей к пользованию аппаратом!
H Gyerekek a gépet nem kezelhetik
TR Makinayý Çocuklar Kullanmamalýdýr.
DK Må kun betjenes af voksne
CZ Stroj nesmí být obsluhován dětmi!
P As crianças não devem trabalhar com a máquina!
GR БРБГПСЕХЕФБЙ З ЧСЗУЗ БРП РБЙДЙБ.
SLO Otroci ne smejo uporabljati naprave
SK So strojom nesmú pracovat deti!
EST Lapsed ei tohi masinat kasutada!
CHI
UAE
D Nicht unter das Messer fassen!
GB Do not reach beneath the blade!
F Ne pas passer les mains sous la lame!
NL Niet met de handen onder het mes komen!
I Non toccare la lama nella parte inferiore!
E ¡No tocar debajo de la cuchilla!
S Sträck inte in handen under kniven!
FIN Älä laita kättäsi terän alle !
N Plasser aldri hender ol. under kniven !
PL Nie wkładać rąk pod noże!
RUS
Избегайте попадания рук под лезвие!
H Ne nyúljon a kés alá!
TR
Elinizi býçaðýn altýna sokmayýnýz!
DK Stik ikke hænderne ind under knivbladet!
CZ Nesahejte pod ostří nože!
P Não tocar na parte inferior da faca!
GR МЗН БГГЙЖЕФЕ ФП КБФЩ МЕСПУ ФЗУ ЛЕРЙДБУ!
SLO Ne segajte z roko pod rezilo!
SK Nevkladajte ruky pod nôž!
EST Ärge pange kätt tera alla!
CHI
UAE
•
Safety precautions
•
- 4 -
IDEAL 4815 • IDEAL 4850
•
Safety precautions
•
D Messer nie lose liegen lassen!
Messer nur mit Messerwechselvorrichtung oder im
Messertransportkasten befördern!
(siehe Seite 27 und 29).
Warnung! Verletzungsgefahr!
GB Never leave the blade unattended!
Do not extract or transport the blade without protection!
(See page 27 and 29).
Danger! Risk of injury!
F Ne jamais laisser la lame sans protections !
Elle ne doit être démontée qu’à l’ aide du dispositif de
changement de lame (cf. page 27 et 29), ou transportée dans
son étui en bois !
Danger! Risques de coupures !
NL Laat nooit de messen alleen achter.
Transporteer de messen niet zonder de houten bescherming
(zie pagina 27 en 29).
Waarschuwing! Opgelet voor ongevallen!
I Non lasciare mai la lama incustodita. Non rimuovere o
trasportare la lama senza protezione. (Vedi pagina 27 e 29).
Attenzione! Rischio di infortunio!
E ¡No quitar la cuchilla sin prestar atención. No desmontar no
transportar la cuchilla sin protección! (vérase pág. 27 y 29)
¡Advertencia! ¡Peligro de hacerse daño!
S Lämna aldrig maskinen obemannad. Ta inte ur eller
transportera kniven utan skydd. (se sid 27 och 29).
Skaderisk!
FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta
terää ilman suojaa ! (katso sivu 27 ja 29
Loukkaantumisen vaara !
N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller
transporter den uten beskyttelse (Se side 27 og 29)
FARE ! Muligheter for skade !
PL Nigdy nie pozostawiać noży bez nadzoru.
Nie wyciągać lub transportować noży bez osłon!
(zobacz strona 27 i 29).
Ryzyko skaleczenia sie!
RUS Не оставляйте открытое лезвие без присмотра! Не
пытайтесь извлечь или транспортировать лезвие без
специальных мер предосторожности!
(См. страницы 27 и 29)
Соблюдайте выше перечисленные правила
для избежания травм!
H Soha ne hagyja a kést őrizetlenül!
Ne vegye ki vagy ne szállítsa a kést védőtok nélkül!
(Lásd 27. és 29. oldal)
Veszély! Sérülésveszély!
TR Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz!
Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya
taþýmayýnýz! (Sayfa 27 ve 29’e bakýnýz)
Dikkat! Yaralanma riski!
- 5 -
•
Safety precautions
•
DK Knivbladet må aldrig efterlades uden opsyn.
Forsøg ikke at afmontere eller transportere knivbladet uden
beskyttelse! (Se side 27 og 29)
FARE! Risiko for legemlig beskadigelse.
CZ Nikdy nenechávejte nůž bez krytu.
Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného
krytu (viz. strany 27 a 29)
Nebezpecí! Riskujete zranení
P Deixar a faca sempre em local seguro!
Não retirar ou transportar a faca sem protecção!
(Ver pág. 27 e 29)
Perigo! Risco de dano!
GR МЗН БЦЗНЕФЕ ФЗН ЛЕРЙДБ БНЕРЙФЗСЗФЗ!
МЗН БЛЛБЖЕФЕ ¹ МЕФБЦЕСЕФЕ ФЗН ЛЕРЙДБ ЧЩСЙУ
РСПЦХЛБОЗ (ДеЯфе учефйкЬ уфйт уелЯдет 27 & 29)
РСПУПЧЗ ! КЙНДХНПУ ФСБХМБФЙУМПХ !
SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte
rezilo brez zaščite. ( glej stran 27 in 29).
Pozor! Nevarnost poškodbe.
SK Nenechávajte nôž nechránený (nezabezpecený)!
Nevyberajte alebo netransportujte nôž bez ochrany
(vid s. 27 a 29
! Riziko úrazu !
EST Ärge jätke lõiketera kunagi järelevalveta!
Ärge pikendage ega teisaldage tera kaitseseadmeteta!
(Vt lk 27 ja 29)
Oht! Vigastuste oht!
CHI
UAE
- 6 -
IDEAL 4815 • IDEAL 4850
D Keine harten und splitternden Materialien schneiden!
GB Do not cut hard materials or materials which may splinter!
F La coupe de matériaux trop durs ou risquant des projections
est interdite !
NL Snij geen harde materialen of materiaal dat kan splinteren!
I Utilizzare il tagliacarte esclusivamente per il taglio di risme
di carta o materiali analoghi!
E ¡No cortar materiales duros o materiales que puedan
astillarse!
S Förstör inte hârt material eller material som kan splittras!
FIN Asentakaa laite lasten ulottumattomiin !
N Ikke kutt hardt metall eller materiale som kan splintre !
PL Nie ciąć twardych materiałów lub materiałów, które mogą
ulec odpryśnięciu!
RUS
Данный резак не предназначен для резки твердых
материалов или материалов, которые могут
расщепляться!
H Ne vágjon kemény vagy olyan anyagot, amely repedhet!
TR Sert veya parçalanabilecek malzemeleri kesmeyiniz!
DK Der må ikke skæres i hårde materialer eller i materialer, der
kan splintre!
CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré
úlomky!
P Não cortar materiais duros ou materiais que possam lascar!
GR МЗН КПВЕФЕ УКЛЗСБ ХЛЙКБ ¹ ХЛЙКБ РПХ
ИСХММБФЙЖПНФБЙ!
SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko
razcepijo.
SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu
vystrelovat ostré úlomky.
EST Ärge lõigake kõvasid materjale ega materjale, mis võivad
pilbasteks puruneda!
CHI
UAE
•
Safety precautions
•
- 7 -
The machine is designed for cutting stacks of
paper to a specified size.
This machine is constructed for "one-man
operation" only!
Warning! Clips or similar damage the
cutting blade.
Disconnect from the mains before starting any
service work or before removing the panels!
Replacement of blade and cutting stick may
be performed only when the main switch is
switched off!
•
Safety precautions
•
- 8 -
IDEAL 4815 • IDEAL 4850
A
A
A
C
A
C
B
All components which could endanger the
operator are covered by a guard!
Operating the machine without safety device is
forbidden!
(Front safety guard (A), rear screwed safety
guard (B) and panel (C).
•
Safety precautions
•
- 9 -
A
C
B
A
B
The dangerous cutting movement is
safeguarded by a movable guard (A) and a
safety two-handed control system! (B)
Before working with the machine and after
every blade replacement the automatic cut-off
function of safety guard (A),(correct if distance
between cover and table is < 20 mm) main
switch (B) and control panel (C) must be
checked.
•
Safety precautions
•
- 10 -
IDEAL 4815 • IDEAL 4850
230V / 10A min
115V / 15A min
Protect mains cable against heat, oil and
sharp edges!
Connect the power cord to a single phase
socket.
Ensure free access to mains!
•
Safety precautions
•
- 11 -
When not in use for a longer period switch off.
(Main switch to "0").
•
Safety precautions
•
Clamping
Blade
OK
OK
Warning by IDEAL 4815
Danger!
Blade must always be covered by the
pressing bar.
- 12 -
IDEAL 4815 • IDEAL 4850
Remove the stand from the wooden pallet.
4 strong people are required to lift the machine
from the pallet and place it on the stand.
Secure with 4 screws (A). Put the shelf (B) on
the stand. (Parts and tools are in the tool set
(C).
•
Installation
•
- 13 -
A
•
Installation
•
Tools can be kept in the holder provided .
Cutting sticks (A) can be put in the tool holder
- 14 -
IDEAL 4815 • IDEAL 4850
C
A
C
Tighten the backgauge crank (A). Parts and
tools are in the tool set (C).
•
Installation
•
Only IDEAL 4815
Attach the enclosed hand-wheel for clamping.
Parts and tools are in the tool set (C).
- 15 -
A
Plug into socket.
The machine must be connected directly to the
socket.
•
Installation
•
Side tables (A), left and right are available
as an option (Nr. 9000 528).
- 16 -
IDEAL 4815 • IDEAL 4850
A
A
A
X
A
B
It is forbidden to operate the machine if the
operating and safety instructions have not been
understood. Please check the safety devices
are functioning and complete before use.
•
All covers have to be mounted (A).
•
The release for cutting is allowed only if
the cover is closed and the two-hand safety
device is operated at the same time (B)
•
If the front cover closes by itself the
gas spring (X) needs replacing.
We recommend you keep a record of your test
results.
•
Operation
•
- 17 -
1
9
9
6
4
5
8
2
1
3
7
11 12 13
•
Operation
•
Operating elements
A
- Safety two-handed control system
Pre-clamping (only IDEAL 4850)
and cutting
B
- Overload switch
Blade drive IDEAL 4815
Blade drive, clamp drive,
IDEAL 4850
C
- Display cutting size (cm or inch)
D
- Main switch
E
- Crank handle for backgauge
setting
F
- Key switch
G
- Paper clamp (only IDEAL 4815)
H
- Backgauge
I
- Side lay left and right
J
- Front safety guard
K
- Measuring unit (cm or inch)
L
- Display cutting size (cm or inch)
M
- Changeover (cm/inch)
Warning!
Before cutting a measurement please check
that the measurement scale (cm or inch) is
adjusted correctly. See left picture.
Cutting activation
Warning!
• Run backgauge to the front for turning the
paper stack.
• Do not interrupt the upward movement of the
blade by performing switching procedures.
• Close the front safety guard
J
.
• Blade must always be at the top and be
covered by the clamp. Do not touch the
blade.
(see safety information on page 32).
Risk of injury!
- 18 -
IDEAL 4815 • IDEAL 4850
C
A
B
Position the main switch D to "I" (A). Insert the
key F for the control system and move it to the
right (B). Open the safety guard
J
(C). The
machine is now ready for use.
•
Operation
•
- 19 -
A
B
C
D
E
The measurement is set with the backgauge
crank.(A) The symbol – rotary direction –
moves to the right on the display (B) (see
picture C). The rotary direction of the
backgauge crank (A) is indicated on the right.
Keep turning the backgauge crank to the right
until a measurement appears (see picture E).
The reference position is reached.
The cutting size can now be set with the
handle (A).
If the backgauge is right at the front the
symbol – rotary direction – will move to the left
(see picture D). Turn the backgauge crank to
the left until the rotary direction appears on the
right
in the display (see picture C).
Afterwards turn the backgauge crank to the
right until a measurements appears (see
picture E). The reference position is reached.
The cutting size can now be set with the
handle (A). Proceed to position from the
rear.
Measurement is shown on the display in
inches or cm (B).
Information:
When the machine is only switched off by
the Key switch
F
(main switch D is still ON) it
is not necessary to advance to the reference
point.
•
Operation
•
- 20 -
IDEAL 4815 • IDEAL 4850
A
B
Cut according to markings
Optical cutting line (A) that indicates the exact
position of the cut. Blade cuts on the front
edge (B) of the light beam. (Only use when no
exact cut is required).
•
Adjust the backgauge with the crank handle
E
to the back.
•
Insert paper and move by means of the
stacking angle to the backgauge
H
and side
lay on the left
I.
•
Turn the crank handle E to the right until the
marking on the paper to be cut is below the
cutting line indicator.
Pull out the handle to avoid the measurement
being wrongly adjusted.
•
Operation
•
- 21 -
B
A
B
C
A
Position the paper on the backgauge (A) and
side lays left or right (B).
To move paper stacks, please use the paper
knock-up block (C) provided.
(Run backgauge to the front for turning the
paper stack).
•
Operation
•
Only 4815
Clamping is released by the hand-wheel.
Before every cut lower the clamp by turning the
hand-wheel to the right and tighten with a light
twist.
IDEAL 4815
Press both actuators of the two-handed control
system activation (A) simultaneously and them
pressed until the paper is completely cut.
- 22 -
IDEAL 4815 • IDEAL 4850
A
+ =
+ =
+ =
IDEAL 4850
IDEAL 4850
The clamp moves automatically when cutting
is activated.
The paper can also be pressed in advance.
Clamping and cutting is activated by
pressing actuators (A) on the front table.
•
Operation
•
+ =
+ =
+ =
Switch position 1
Switch position 2
Pre-clamping
Press down both actuators to step 1
Clamp returns
Press down completely one of the actuators
Cutting sequence with automatic clamping
Press down both actuators to step 2
IDEAL 4850
The actuator has 2 switching steps:
1. pre-clamping
2. automatic clamping and cutting
- 23 -
A
A
Close the safety guard.
Cutting activation:
Press both buttons of the two-handed control
system activation (A) simultaneously and them
pressed until the paper is completely cut.
To interrupt or stop cutting:
To interrupt or stop cutting, release
both buttons (A) of the two-hand control.
•
Operation
•
- 24 -
IDEAL 4815 • IDEAL 4850
•
Blade and cutting stick replacement
•
If the cutting quality decreases:
•
Check the cutting depth (see page 32).
•
Check the cutting stick (see page 28).
•
Replace or grind the blade (see page
24 - 32).
The blade cannot be ground if the blade
height is less than 83 mm/3,29 inches.
A new blade must be used.
The blade may only be ground by a qualified
supplier or from the manufacturer
Krug & Priester, D-72336 Balingen.
Danger! Risk of injury!
The blade is extremely sharp. Do not
extract or transport the blade without
protection. Changing the blade may only be
performed by trained staff.
- 25 -
3.
2.
1.
Turn the blade depth adjustment screw to the
left until it stops. (Screwdriver found in tool set
(A).
Close the safety guard (1.).
Lower the blade by pressing both cutting
actuators (2.). Keep one actuator pressed and
turn off the main switch (3.).
•
Blade and cutting stick replacement
•
- 26 -
IDEAL 4815 • IDEAL 4850
B
A
C
The 3 eccentrics are now exposed and should
be turned counter clockwise to position "0"
with the special wrench and attachable
extension pipe (A) (in the tool set). The slot
must correspond to position "0" (B).
Unscrew the blade screws (C) on the right
hand side.
Clamping
Blade
OK
OK
•
Blade and cutting stick replacement
•
Remove the special wrench and turn on the
main switch until the blade returns to the home
position.
Warning by IDEAL 4815
Do not turn main switch to position "0"
whilst blade is moving upwards!
The clamp must always overlap the blade!
Danger! Risk of injury!
- 27 -
A
2.
1.
3.
3.
4.
2.
B
A
1.
Position the main switch to "0" (1.)
Remove the 2 blade screws on the elongated
holes (2.). Then put the blade changing tool (A)
into place and fasten it to the blade (3.).
Remove 2 blade screws (1.).
Loosen the grips (2.) of the blade changing
tool (A) lightly and allow the blade to be taken
downwards out of the machine (3.). Place the
blade into the blade carrier (B) and screw it
into place (4).
•
Blade and cutting stick replacement
•
- 28 -
IDEAL 4815 • IDEAL 4850
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned
or exchanged. (The cutting stick can be used
eight times).
•
Blade and cutting stick replacement
•
Replacing the cutting stick (not the blade).
• Turn the blade adjusting screw (A) to the left
until it stops. (Otherwise the first cut will be
too deep).
• Remove the cutting stick according to top
picure.
• Turn the cutting stick (the non-used side
must be near to the blade) and plug it into the
holding bolt.
Danger! Risk of injury!
Cutting test after replacing the cutting stick
(not the blade)
• Insert the paper and release the cut.
• If the last sheet of paper is not cut along the
entire length turn the blade adjusting screw
(A) ¼ turn to the right.
• If the last sheet is still not completely cut
repeat this process until the last sheet is cut
along the entire length.
- 29 -
2.
1.
A
A
11 mm
0.43 inch
C
B
B
C
Place the blade to be exchanged with the
blade changing tool (A) mounted (1.), into the
blade carrier and push it up to the top and
screw it into place with the grips (2.).
•
Blade and cutting stick replacement
•
Take the exchange blade carefully out of the
blade box and screw it to the blade changing
tool (A).
• Make sure there is a space ot 11 mm or
0.43 inches! (B).
• Blade must be covered! (C).
Danger! Risk of injury!
- 30 -
IDEAL 4815 • IDEAL 4850
2.
1.
2.
A
1.
3.
B
Lightly tighten 2 of the 5 blade screws with
washers (1.). Remove the blade changing
tool (2.). Lightly tighten the remaining blade
screws with washers (3.).
Lightly screw in the right blade screw with the
washer (A) when the blade is lowered.
Remove all tools and distribute paper along
the entire cutting length (1.).
Turn main switch to position "I" (2.).
•
Blade and cutting stick replacement
•
- 31 -
2.
A
1.
A
4.
5.
1.
3.
2.
Close the safety guard (1.) Lower the blade by
pressing both cutting buttons (2.). Keep one
button pressed and turn off the main switch (3.).
Open the safety guard (4.). With the special
wrench (B) the 3 eccentrics should be screwed
down (5.)until the paper is cut along the
entire length of the blade (The blade must
remain parallel, not too deep into cutting stick).
•
Blade and cutting stick replacement
•
Tighten the blade screws (A) on the right hand
side.
Turn main switch to position "I" (1.). Blade will
return to upper position. Tighten the blade
screws (2.) firmly.
Warning by IDEAL 4815
Do not turn main switch to position
"0" whilst blade is moving upwards! The
clamp must always overlap the blade!
(see page 32).
Danger! Risk of injury!
- 32 -
IDEAL 4815 • IDEAL 4850
A
Clamping
Blade
OK
OK
•
Blade and cutting stick replacement
•
Paper cutting test. If the last sheet or several
sheets are not completely cut, gradually turn
the knob for blade depth adjustment (A)
¼ turn to the right until the paper is cut along
the entire length. Do not set too low as blade
will become blunt sooner.
Warning by IDEAL 4815
Danger!
Blade must always be covered by the
pressing bar (see picture below at the left).
- 33 -
D
Grease the backgauge (A) control weekly with
a grease gun. Advance the backgauge as far
as possible to the front. (Use non-resinous oil
or grease).
Grease the remaining parts twice a year (see
picture).
The main switch must be on "0" (B).
Remove panel (C). Tools in tool set.
• Remove any paper.
• Grease the machine.
• Check the 4 joining bolts and 2 pushing bars
for wear (D). If necessary inform your service
personnel.
• Mount the machine.
•
Maintenance and cleaning
•
= Greasing points on the machine.
Maintenance work may only be performed by
trained staff.
Danger! Disconnect the mains before
starting any service work or before
removing the cover.
- 34 -
IDEAL 4815 • IDEAL 4850
Safety test
The safety regulations are according to the
regulations of the country where the cutting
machine is operated. The manufacturer
recommends a safety check is made every 5
years by an authorised service team.
•
Maintenance and cleaning
•
- 35 -
A
B
Is the machine plugged in?
Main switch to position "I"? (A)
Control system activated? (B)
(Turn key to the right)
Check the units fuse and the on-site circuit
breaker!
Release a cut see page 21 and 22.
•
Possible malfuntions
•
Machine does not function!
- 36 -
IDEAL 4815 • IDEAL 4850
•
Possible malfuntions
•
Cut cannot be made.
•
If cover is open:
close it.
•
If cover is closed:
open and re-close it. (Security check).
- 37 -
A,B
Machine turns off:
•
Machine overloaded.
Safety button (A) ejects.
(Allow 1 minute cooling time and reset the
safety button (A).
•
Machine blocked.
•
Blade is blunt.
Eliminate the cause, and push the safety
button (A).
Only IDEAL 4850
•
Clamping drive blocked
Safety button (B) ejects.
Eliminate the cause, and push the safety
button (B).
Safety button for:
A =
Blade drive
B =
Clamping drive
•
Possible malfuntions
•
- 38 -
IDEAL 4815 • IDEAL 4850
B
C
A
Does not cut through the last sheet:
•
Turn or turn around the cutting stick (A),
readjust the blade by means of the blade
adjusting knob (B)
(see page 32).
Poor cutting quality or blade stays in the
paper stack.
•
Change the blade (C) (see pages 24 - 32.
•
Possible malfuntions
•
- 39 -
A
C
B
Display illumination off
•
Machine is plugged in? (A)
•
Main switch on position "I"? (B)
•
Push in the safety button! (C)
•
Check the units fuse and the on-site circuit
breaker!
•
Possible malfuntions
•
Motor runs but blade does not move
downwards.
•
Security brake has been activated!
Inform the Service Team!
•
www.ideal.de "Service"
service@krug-priester.com
- 40 -
IDEAL 4815 • IDEAL 4850
•
Possible malfuntions
•
None of the above mentioned methods
helped to solve the problem:
Contact Service Team under
•
www.ideal.de "Service"
service@krug-priester.com
- 41 -
•
Accessories
•
Recommended accessories:
Blade
•
Nr. 9000 021
Cutting stick (6 pieces)
•
Nr. 9000 022
Blade changing tool
1
•
Nr. 9000 518
Paper knock-up block
1
•
Nr. 9000 521
Side tables left and right
•
Nr. 9000 528
1
Included in delivery
- 42 -
IDEAL 4815 • IDEAL 4850
Technical data:
•
Power supply: 230V/50Hz/1~,120V/60Hz/1~
•
Cutting height: 80 mm
•
Sound level EN 13023: < 70 dB (A)
•
Leakage current < 3,5mA
•
Power cord gauge min. 1,5mm2 (230V).
•
Power cord gauge AWG 14 (15A) (120V)
(IDEAL 4815)
•
Power cord gauge AWG 12 (20A) (120V)
(IDEAL 4850)
The exact technical specifications can be
found on the technical specifications sticker (A)
on the machine. A wiring diagram is found in
the electrical switch box.
To claim under guarantee, the machine must
still carry its original identification label.
•
Technical data
•
* with side tables: 1365 mm
** with side tables: IDEAL 4815 / 221 kg
*** with side tables:IDEAL 4850 / 234 kg
Cutting-
length
mm
Table-
depth
mm
Minimum space
requirement
(B X T X H) mm
Weight
kg
IDEAL 4815 475 458 765* x 1080 x 1435 212**
IDEAL 4850 475 458 765* x 1080 x 1300 225***
- 43 -
•
Technical data
•
This machine is approved by independent
safety laboratories and is in compliance with
the EC-regulations 2006/42/EG and
2004/108/EG.
Sound level information:
The sound level is < 70 db (A) as defined by
EN 13023.
Subject to alteration without notice.
- 44 -
IDEAL 4815 • IDEAL 4850
Krug + Priester has a certified quality
management system according to DIN EN
ISO 9001:2008 and a certified environmental
management system according to DIN ISO
14001:2009.
•
Technical data
•
- 45 -
D EG-KONFORMITÄTSERKLÄRUNG
GB EC-declaration of conformity
F Déclaration de conformité CE
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
GS- IDENT. Nr. UL- IDENT. Nr.
4815 11481001 10481001
4850 11485001 10485001
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
2006/42/EG:
Maschinenrichtline, EC Machinery directive, EC Directives machines.
2004/108/EG:
EMV Richtline, EMV Electromagnetic compatibility directive,
EMV directives compatibilité électromagnétique
2011/65/EU
RoHS Richtlinie, RoHS directive, RoHS directives.
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN ISO 12100;
EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1
Bevollmächtigter für technische Dokumentation
Authorized representative for technical documentation
Représentant autorisé pour la documentation technique
Krug & Priester GmbH u. Co KG
Simon-Schweitzer-Str. 34
D-72336 Balingen (Germany)
29.12.2009
Datum
- Geschäftsführer-
- 46 -
IDEAL 4815 • IDEAL 4850
Remarks:
- 47 -
Remarks:
IDEAL • Made in Germany
•
IDEAL
•
72336 Balingen • Germany
•
www.ideal.de
•
Printed in Germany • IDEAL 08/2013
• Document Shredders •
• Trimmers and Guillotines •
Loading...