IDEAL INDUSTRIES HE C28, HE C24 User Manual

users guide

mini HE

Your Idea l users g uide

C24,C28

For installation and servicing guide see
reverse of book

When replacing any part of this appliance, use only spare parts that you can be
assured conform to safety and performance specification that we require. Do not use
reconditioned or copy parts that have not been clearly authorised by Ideal Boilers

mini HE

mini HE C24 G.C. appliance No. 47 ---348---38
mini HE C28 G.C. appliance No. 47 --- 348 ---39

Destination countries: GB, IE

INTRODUCTION

mini HE are wall mounted, room sealed, condensing, low

water content combination gas boilers featuring full sequence
automatic spark ignition and fan assisted combustion.

SAFETY

theboilercasemustbeallowedforservicing.
After installation the following clearances are allowable during
use, providing the encasing parts are removeable for servicing:
The bottom clearance can be reduced to 20mm (3/4”).
The front clearance can be reduced to 50mm (2”).

BOILER CONTROLS

Current Gas Safety (Installation & Use)
Regulationsorrulesinforce

In your own interest, and that of safety, it is the law that this boiler
must be installed by a CORGI registered installer or in IE a
competent person, in accordance with the above regulations.

It is essential that the instructions in this booklet are strictly
followed, for safe and economical operation of the boiler.

ELECTRICITY SUPPLY

Theappliancemustbeefficientlyearthed.

Supply 230 V 50 Hz. The fusing should be 3 A.

Connection must be made in a way that allows complete
isolation of the electrical supply, such as a double pole switch,
having a 3 mm (1/8”) contact separation in both poles, or a
plug and socket serving only the boiler and system controls.
The means of isolation must be accessible to the user after
installation.

IMPORTANT NOTES

F This appliance must not be operated without the casing

correctly fitted and forming an adequate seal.

F If the boiler is installed in a compartment then the

compartment MUST NOT be used for storage purposes.

F Under no circumstances should any of the sealed

components on this appliance be used incorrectly or
tampered with.

F If it is known or suspected that a fault exist on the boiler

then it MUST NOT BE USED until the fault has been
corrected by a CORGI registered installer or in IE a
competent person.

MINIMUM CLEARANCES

Clearances of 200 mm (7 7/8“) above and below, 25 mm (1“)
at left, 50 mm (2“) at right and 450 mm (17 3/4“) at the front of

BC D EF

A

A Appliance operation lights

B Domestic hot water temperature control

C Main switch and radiator temperature control

D Boiler reset button

E Lock - -- out signal lamp

F Programmer (optional)

G System pressure and temperature gauge

G

TO LIGHT THE BOILER

1 Check that the valves located in the lower part of the boiler

are open.

2 Switch the electricity supply on.

The appliance operation light A will flash every 4 seconds
(stand---by condition).

3 If the boiler is to be used for CH and DHW position the

main switch as in the following illustration.
The appliance operation light A will flash every 2 seconds
(operating boiler).

A

C

DIAGNOSTIC LIGHTS

The following table gives a summary of the relationship
between each of the possible light combinations and their
meaning during normal operaion of the boiler

All CORGI registered installers carry a CORGI ID card, and have a registration number. Both should be recorded in the Benchmark
Commissioning Checklist. You can check your installer by calling CORGI direct on 01256 372300.

Caradon Ideal Limited is a member of the Benchmark initiative and fully supports the
aims of the programme. Benchmark has been introduced to improve the standards of
installation and commissioning of central heating systems in the UK and to encourage
the regular servicing of all central heating systems to ensure safety and efficiency.

THE BENCHMARK SERVICE INTERVAL RECORD MUST BE COMPLETED AFTER EACH SERVICE