LANTEK®LAN Cable Testers
Quick Reference Guide
33. Disconnect Remote Patchcord,
connect Display Patchcord
between units, press F1.
34. Disconnect Display Patchcord
from Remote Handset, Connect
Remote Patchcord to Remote
Handset, press F1 on Display
Handset, press Autotest on
Remote Handset.
35. Calibration Complete,
press Escape.
36. Tester is now setup for CAT 6
Test Standard, to be saved in
Compact Flash on Slot 1, the
current job selected is IDEAL
INDUSTR IES INC, Cable ID
starts at “TEST 0001.”
IDEAL IN DUSTRIE S, INC.
Becker Place, Sycamore, IL 60178, USA / 815-895-5181 • 8 00-435-0705 in USA
International offices:
Australia • Brazil • Canada • China • Germany • India • Mexico • UK
For complete sales office contact information, visit us at:
www.idealindustries.com
10/06
Printed in U.S.A.
Form No. 6510-30-0400 Rev.F
©2006 IDEAL IND USTRIES, INC.
LANTEK®LAN Cable Testers
Quick Reference Guide
For more calibration procedures,
visit www.idealindustries.com
For more calibration procedures,
visit www.idealindustries.com
Pass/Fail Reporting
Power-Up
Overall test result is a pass.
Overall test result is a fail.
Individual Autotest Results
All values pass with sufficient margin.
One or more values fail.
or — Pass or fail by a small margin.
You are now ready to perform an AUTOTEST on the cable you have setup.
Wiring Configuration Figure 2
LANTEK
Setup Procedure
The following procedure will show you step-by-step how to setup
test Preferences, specify Cable Type to test, setup Cable ID, Job
Naming and Selection. After completing the LANTEK Field
Calibration procedure, you are all set to starting testing CAT 6
using single button AUTOTEST on the Display or Remote Handsets.
Section 1: Preference Setup
Section 2: Cable ID Setup
Section 3: Job Naming & Selection
Section 4: Cable Type Setup
Section 5: Field Calibration
Section 1: PREFERENCES Setup
Section 2: CABLE ID Setup
Section 3: STORED Tests, Job Naming & Selection
1. Highlight Preferences icon,
press Enter.
2. Highlight User Information
and press Enter.
3. Enter appropriate information, it
will be reflected in the tests
reports, press Enter upon
completion.
4. Press down arrow to highlight
Autotest Pref, press Enter.
5. Make changes as required,
press Enter.
6. Highlight Measurement Units,
press Enter.
7. Press F1 to change to “m”, or
press Enter.
8. Highlight Date and Time,
press Enter.
9. Make changes then press Enter.
10. Highlight Select Save Media,
press Enter.
11. Highlight desired save media,
press Enter.
12. Display will revert to previous
screen, Slot 1 Storage selected.
13. Highlight Wiremap Color
Scheme, press Enter.
14. STD (Black & White) is default.
15. Press F2 for 568-A, or F3 for
568-B, press F4 to Save.
16. Display will revert to previous
screen, press Escape.
17. Press F1 or highlight the Cable
ID icon, press Enter.
18. Highlight Set Cable ID,
press Enter.
19. Enter cable name and Current
Value, use arrow buttons to go
between Cable Name &
Current Value, press Enter.
20. The display will revert to the
previous screen, Current Value
is updated, press Escape.
21. The display will return to the
Ready screen, press right arrow.
22. Stored Tests icon is highlighted,
press Enter.
23. Press F2 for Options.
24. Highlight New Job and
press Enter.
25. Enter Job Name as required,
press Enter.
26. Job list is updated, Current job
updated, press Escape.
LANTEK®LAN Cable Testers
Loading...