E77
Bill Acceptor
Installation Guide
2007 International Currency Technologies Corporation
V. 3.0 Part Number : H4913B-R
International Currency Technologies Corp.
Contents
1. Introduction ......................................................................... 2
1-1. Overview ...................................................................... 2
1-2. Features ...................................................................... 2
2. Specifications ..................................................................... 2
General ............................................................................... 2
Electrical ............................................................................. 3
Use of Materials Limitations
International Currency Technologies Corporation (ICT) all rights reserved.
All materials contained are the copyrighted property of ICT.
All trademarks, service marks, and trade names are proprietary to ICT.
ICT reserves the right at all times to disclose or to modify any information as
ICT deems necessary to satisfy any applicable law, regulation, legal process
or governmental request, or to edit, refuse to post or to remove any information
or materials, in whole or in part, in ICT's sole discretion.
Mechanical ......................................................................... 3
3. Packing List ........................................................................ 3
4. Dimension .......................................................................... 4
5. Installation .......................................................................... 6
5-1. PIN Assignment ............................................................6
5-1-1. I/O Circuit ............................................................. 7
5-2. DIP Switch Setting ....................................................... 8
5-3. Software Download and Upgrade .............................. 8
6. Maintenance ....................................................................... 9
7. Troubleshooting ................................................................... 10
1
www.ictgroup.com.tw
Bill Acceptor Bill Acceptor
E77 E77
1. Introduction
1-1. Overview
E77 features a high currency verification and recognition with
new
verification unit which including auto calibration and antistringing function with multiple interfaces to provide users the
best service.
1-2. Features
Fixed-width/ Multi-width bill acceptable.
Multi-currencies acceptable.
Anti-stringing technologies.
Auto calibration available.
Durable construction design.
High transaction speed.
Multiple interfaces available.
Easy maintenance.
Installation: Indoor use only!!
Electrical
Power Consumption
Power Source
Operation Environment
Mechanical
12V- Standby : 0.35A, 4.2 W
Operation: 2.3 A, 27.6W
Maximum: 4 A, 48 W
12V DC (11.4~12.6V DC)
Operation Temperature: 0°C~55°C
Storage Temperature: -20°C~70°C
Humidity: 30%~85RH
(no condensation)
2. Specifications
General
Acceptance Rate
Note: The incomplete bills such as extremely dirty, wet, broken or
wrinkled ones are excluded.
Bill Insertion
Transaction Speed
Interface
Bill Accepted Width
www.ictgroup.com.tw
Outline Dimension
Weight
96% or greater
Refer to page. 4
Approx. 1.2kg
3. Packing List
Four way acceptance
Main
Accessory
Approx. 2 seconds to stack
Parallel
Approx. 77mm
2
Bill Acceptor
E77 Installation Guide
E77 DIP Switch Setting Guide
3
www.ictgroup.com.tw
Bill Acceptor Bill Acceptor
E77 E77
4. Dimension
90.00[3.54]
78.00[3.07]
72.00[2.83]
65.00[2.56]
85.00[3.35]
95.28[3.75]
Figure 1
To install the bill acceptor on your VMC, please be aware of the
dimension as below:
[ L ] : Longer than the maximum length of accepted bills.
[ L1 ] : Bill box capacity depth.
* [ L/2 ] has to be longer than 70mm to open upper base.
Figure 2
L/2
L
86.00[3.39]
87.00[3.43]
64.53[2.54]
52.90[2.08]
99.20[3.91]
128.70[5.07]
87.00[3.43]
61.50[2.42]
LL1
www.ictgroup.com.tw
Unit : :mm
4
[in]
5
www.ictgroup.com.tw
Bill Acceptor Bill Acceptor
E77 E77
5. Installation
5-1. PIN Assignment
Figure 3
5-1-1. I/O Circuit
Parallel Interface.
Figure 4
(CN1)
11
13
15
17
19
21
23
25
3
5
7
9
25
26
CN1
10
12
14
16
18
20
22
24
26
2
4
6
8
INHIB
ACK
REJ
PRES
1
A 1
A 2
A 3
A 4
A 5
A 6
A 7
A 8
A 9
A10
A11
A12
A13
B 1
B 2
B 3
B 4
B 5
B 6
B 7
B 8
B 9
B10
B11
B12
B13
13X2
1
2
POWER+12V POWER GND
VEND1
VEND2
VEND3
ABN
STKF
VEND1~3
STKF
PRES
ABN
Bill Acceptor
+5VDC
REJ
ACK
INHIB
Bill Acceptor
10K
10K 10K
+5VDC~+12VDC
4K7
E-VEND1~3
E-STKF
E-PRES
E-ABN
Customer Side
E-REJ
E-ACK
E-INHIB
Hi"TR ON
Lo"TR OFF
TR
Customer Side
www.ictgroup.com.tw
6
7
www.ictgroup.com.tw
5 4 3 2 1
9 8 7 6
Bill Acceptor Bill Acceptor
E77 E77
6. Maintenance
5-2. DIP Switch Setting
There is one serial DIP switches which are located on the side
of E77(as Figure 5). According to different currencies and credit
output format which are used by users, DIP switch settings could
be varied to fit users' need.
Please refer to “E77 Series DIP Switch Setting” Guide in the
package for more details.
Figure 5
Foreign objects on the LED or sensor may cause bill jamming and
decrease acceptance rate. To make sure the bill acceptor always
works smoothly, please clean the internal parts regularly.
To clean the internal parts:
1. Turn Bill Acceptor off.
2. Push the buttons on both sides of bill path and open the unit.
3. Use a soft, dry cloth or towel to clean the bill path and sensors.
Buttons
Sensor
5-3. Software Download and Upgrade
To download and upgrade the software to E77, the programmer
(FP-001) is needed. Please contact ICT to purchase FP-001 and
refer to FP-001 user guide for software download and upgrade
information.
COM2
FirmwareFirmware
WEL-R087
E77
www.ictgroup.com.tw
PH
WEL-R7U03
Please turn on Bill Acceptor after connecting..
FP-001
8
Figure 6
PC
Alcohol
Figure 7
Sensor
Maintenance Notice
(Any improper maintenance will result invalid warranty.)
Recommended
DO NOT USE
Mild, non-abrasive, soap water.
Organic solvent , Alcohol, Volatility liquid.
9
www.ictgroup.com.tw
Bill Acceptor
E77
7. Troubleshooting
LED
Flashes
1
2
Status
Bill jammed.
Inhibit
LED
Corrective Actions
Open bill path and then remove the
jammed bill.
Inspect for right DIP switch setting.
Figure 8
Table 1
Taiwan
International Currency Technologies Corporation
Ji-Hong Building, No 24, Alley 38, Lane 91, Nei-hu Rd., Sec. 1, Taipei, Taiwan, R.O.C.
Tel: 886-2-2797-1238 ‧ Fax: 886-2-2797-1634
sales@ictgroup.com.tw (For Sales)
rma@ictgroup.com.tw (For Customer Service)
Website: www.ictgroup.com.tw
3
Sensor error.
A stringing attempt
4
has detected.
Motor error.
7
www.ictgroup.com.tw
Inspect for foreign objects on sensor or
bill path and clean.
Inspect for foreign objects on sensor or
bill path and clean.
Inspect for foreign objects on bill path
and clean.
If the error can not be solved after corrective actions or
happen again, please contact ICT for technical support.
10
Loading...