iCreation BT-129 Product Information Manual

Download

Page 1

Product

Information Guide

BT-129

Page 2

This guide contains helpful information

that enables you to enjoy all of the features

of your speaker.

Welcome. You are using Waterproof Bluetooth Speaker.

Specifications

Bluetooth Compliance

Bluetooth V 4.0

Frequency Band

2.4~2.4835GHz ISM Spectrum

Operating Range

Modulation

GFSK (Gaussian Frequency Shift Keying)

Up to 10m (indoor)

Battery Capacity

Charging Time

3.7 2200mAhV,

About 3 hours

Standby Time

Compatibility

About 120 hours

Mobile phone/device supporting Bluetooth

V1.1 (and above)

Power Supply

5V, 0.5A

Size

Ambient temperature

Humidity

141mm*91mm*54mm

-20 ~ 60℃℃

45%~70%

*Design and specifications are subject to change without notice.

Page 3

Congratulations

Thanks for purchasing the wireless speaker BT-129. Enjoy this smart product, please read below instructions carefully. It's more than just a Bluetooth Speaker!

Care and Maintenance

Do not attempt to service the product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your local reseller before you send the product for repair. Do not use the product in temperature exceed the standard. Extreme temperature will lead to damage of product, decrease of battery capacity or product durability. Keep the product out of the reach of children or

animals. Do not use the product close to other wireless

devices or radiators. Do not drop the product into the fire, battery

explosion will cause personal injury or death. Use the product in proper volume, extremely high volume can be harmful for your ear. Fully charge the product before use if it has not been used for a long period of time.

Volume isnot highenough

Increase the volume of mobile phone/device or BT-129 volume.

Ensure that the mobile phone/device or BT-129 has been charged.

Hearing Distortion

Lower BT-129, Mobilephone/device volume. If lowbattery capacity, pleasecharge it.

Troubleshooting

Can notpaired withBluetooth device

Make surethat your mobile phone/device iscompatible with Bluetooth.

Make sureit's chargedup. Turn off your BT-129 and mobile phone/device, then power

on andreconnect

Signal lossor distortion

Move BT-129 tothe placenearthe mobile phone/device. Ensure it'scharged up. Power off the BT-129, Mobile phone/Device, then repower

on.

Page 4

Contents

Congratulations Care and Maintenance

Feature List

Layout

Use Instrution

Battery/Charger

Operations

LED Indicator

Troubleshooting Specifications

8 13

Page 1

LED Indicator

Speaker Status

LED Status

Power On

Blue LED flash .

Pairing

Pairing Succeed

Power Off

Red LED stay on for a while and get off.

Red LED and Blue LED flash alternately.

Blue LED flashes times along with

beeps.

two

Standby

Blue LED flashes once every 8 seconds.

Music Playing

During a Call

Incoming Call

Red LED flashes quickly(steadily).

Red LED lights steadily.

Blue LED flashes once every 8 seconds.

Battery low

Charging

Full charging

Red LED off.

Red LED flashes along with triple beeps every 30 seconds.

Disconnected

Red LED and blue LED flash simultaneously.

Page 5

Features List

1. Clear and crystal sound , superior stereo performance

2. Build-in microphone

3. Loud , clear , deep bass and stable

4. Wrapped by TPU replaceable and colorful skin

5. Shockproof and Scratchproof

6. Bluetooth connection (

7. Music playing control

8. Voice dialing

9. Bluetooth stereo A2DP/AVRCP)

10. Low battery clarm ( Alarm and LED indicator)

11. LED indicator (Low battery/Charging/full charging)

12. Receiving and rejecting a call by button

13. Last number redial

14. Mute function

15. Multi-function key

16. Bluetooth for 10m distance

(

Waterproof(IPX7),

Bluetooth V4.0)

Notes:

The music player build-in your mobile phone is necessary to support this feature.

Pair and connect your mobile phone with the speaker before using this feature.

If a call is coming in when you are listening to music, the music will pause automatically and replaced by the incoming-call-tone. Once the call is finished, the music will continue.

After the speaker is connected to your mobile phone via Bluetooth,

Press 2 seconds to play next song. Press 2 seconds to start over the current song or get backward to the previous song. Press 1 time or press time to adjust the volume.

press on the speakerto play, pressit again to

pause.

Music Playing

Page 6

Layout

Microphone

Speaker Mesh

LED Light

Loudspeaker

Front View

Rubber Sleeve

Rear View

There will be two beeps every 5 seconds until you hold these twobuttons againto un-mute themicrophone.

Voice Dialing

In standby mode, short press and at the same time then youwill heara tone forvoice dialing.

Note:

This functionneed thesupport of themobile phone.

Mute/Un-mute

Press and at the same time during a call to mute the microphone. Asingle beep willfollow toindicatesuccess of theoperation.

Note:

Page 7

Audio

INPUT

USB jack

Audio in jack

Top View

Side View

Calling

Answer acall

Short press to answeran incoming call.

Reject acall

Press andhold for 2seconds toreject the call.

End a call

After calling,short press to endthe call, or end the call

on the phone.

Last NumberRedial

Short press 2 timesto redial thelast call.

Volume+

Multi-function

(MFB)

Volume-

Page 8

Use Instruction

Function Key

Function

Mode

Operate

Multi-Function key/Power On/Off

Item

One Key

Play/Stop

Paired with

Last Number Redial

Voice Dialing

Answer a Call

Reject a Call

End a Call

Music Play

Power off

Standby

Call

Press Multi-Function key 7 seconds

Press Multi-Function key 2 times

Press Multi-Function key 1 time

Short press Vol+ & Multi-Function key

Press Multi-Function key 2 seconds

Press Multi-Function key 1 time

Volume(Vol -)

One Key

Mute Off/On

Next Song

Volume Up

Current/

Previous Song

Volume Down

Call

Short press Vol+ & Vol-

Play

Standby /Call

Play

Standby /Call

Press Vol+ 2 seconds

Press Vol+ 1 time

Press Vol - 1 time

Press Vol - 2 seconds

Volume+ (Vol +)

One Key

Note: This product have 3 keys: Multi-Function key, Volume+, Volume-,

Specific Instruction please see above.

Press and hold for 7 seconds. Wait until red LED and blue LED flash alternatively along with two beeps.

Pairing and connecting

Pair

1.Enable Bluetooth function on your phone or other smart devices andsearch Bluetoothaccessoriesin range.

2.Choose BT-129 when it shows up and get connected (input 0000, if a pairing code is requested).

3.When blue LED flashes 4 times along with two beeps, BT-129 gets connected successfully.

Enter pairingmode

Notes:

If the paring is not complete within minutes, the speaker will quit the pairing mode. You need to repeat the steps of pairing again. After the connection is successful, if you turn the speaker off and turn it on again, it will be connected to the last connected mobile phone automatically. Also, a beep will be heard.

Disconnect

Power off the BT-129 or disconnect the Bluetooth function on your phone or other smart devices.

Page 9

Battery/Charger

The speaker has a built-in Li-ion battery ( V, , so it can be used without connecting with a power supply(5V,0.5A). To charge the battery, please

3.7 2200mAh)

connect with

computer orcharger throughchargingline.

When BT-129 is charging the LED status indicator will be RED. When fully charged the RED status indicator LED will go off.

From fully discharged battery to fully charged will take 3 hours.

You can plug thecable to charge BT-129while still using it when its battery is low, but this canshorten the battery life. It is recommended to power off BT-129 and fully charge it before use.

Notes:

Operations

Power On/ Off

Power On:

Power Off:

in poweroff mode,press and hold for 4 seconds to power on BT-129. Wait until the blue LED flashes 3 times along witha singlebeep.

in standby status, to power off the device, press and hold for 3 seconds when it is on . Wait until the red LED off alongwith a single beep.

Volume Adjust

Volume Up:

Volume Down:

press 1 timeto adjust thevolume.

Page 10

This device complies with Industry Canada licence-exempt RSS standard(s). Operation issubject tothe following twoconditions: (1) thisdevice maynot cause interference, and (2)this devicemust accept anyinterference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicablesaux appareils radio exempts de licence. L'exploitation est autorisée auxdeux conditionssuivantes: (1) l'appareilne doitpasproduire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

NOTE:

This equipment has been tested and found to complywith the limits fora ClassB digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonableprotection

against harmfulinterference inaresidential installation.

This equipment generates uses and can radiate radio frequency energyand, ifnotinstalled and used

in accordance with the instructions, may cause harmful interference toradio communications.

However, thereis no guarantee thatinterference will notoccur in aparticular installation.

If this equipment does cause harmful interference to radio or television reception,which canbe

determined by turning the equipment off and on, the user is encouraged totry tocorrect the

interference byone ormore of thefollowing measures:

Reorient orrelocate thereceivingantenna.

Increase theseparation betweentheequipment and receiver.

Connect theequipment into anoutlet on acircuitdifferent from that towhich thereceiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Compliance statement

1. This device complies with Part 15 of the FCC Rules. Operation issubject tothe following twoconditions:

(1) Thisdevicemay not causeharmful interference.

(2) This device must accept any interference received, including interferencethat maycauseundesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate theequipment.

This device was tested for typical body-worn operations.

To comply with RF exposure requirements,

a minimum separation distance of 20mm must be maintained between the user's body

This compliance to FCC radiation exposure limits for an uncontrolled environment, the minimum of 20 cm separation distance shall be maintained between antenna and body.