IC Realtime ICR2200 Instruction Manual

INSTRUCTION MANUAL Ver 1. 1

Outdoor High Speed Dome Camera

Speed Dome Camera Instruction Manual

2/47

This lightning flash with arrowhead symbol is intended to alert the user to the

presence of un-insulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point symbol is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

Speed Dome Camera Instruction Manual

3/47

Important Safeguard

1. Read Instructions

Read all of the safety and operating instructions before using the product.

2. Retain Instructions

Save these instructions for future reference.

3. Attachments / Accessories

Do not use attachments or accessories unless recommended by the appliance manufacturer as they may

cause hazards, damage product and void warranty.

4. Installation

Do not place or mount this product in or on an unstable or improperly supported location. Improperly

installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only

with a mounting device recommended by the manufacturer, or sold with the product. To insure proper

mounting, follow the manufacturer's instructions and use only mounting accessories recommended by

manufacturer.

5. Power source

This product should be operated only from the type of power source indicated on the marking label.

Precautions

 Operating

z Before using, make sure power supply and others are properly connected.

z While operating, if any abnormal condition or malfunction is observed, stop using the camera

immediately and then contact your local dealer.

 Handling

z Do not disassemble or tamper with parts inside the camera.

z Do not drop or subject the camera to shock and vibration as this can damage camera.

z Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your

quality of camera.

 Installation and Storage

z Do not install the camera in areas of extreme temperature, which exceed the allowable range.

z Avoid installing in humid or dusty places.

z Avoid installing in places where radiation is present.

z Avoid installing in places where there are strong magnetic fields and electric signals.

z Avoid installing in places where the camera would be subject to strong vibrations.

NOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICE

Speed Dome Camera Instruction Manual

4/47

○

Introduction

Features 5

Product & Accessories

Parts Name & Functions

○

Installation

DIP Switch Setup 9

Installation using Wall Mount Bracket

Installation using Ceiling Mount Bracket 12

Cabling

○

Operation

Checking Before Operation 16

Preset and Pattern Function Pre-Check

Start OSD Menu

Reserved Preset 17

Preset

Swing

Pattern 19

Group

Other Motion Functions

OSD Display of Main Screen 22

○

How to use OSD Menu

General Rules of Menu Operation 23

Main Menu 23

Display Menu for Main Screen

Privacy Zone Mask Setup

Camera Module Setup

Motion Setup

Preset Setup

Swing Setup

Pattern Setup

Group Setup

System Initialization

○5 Specifications

Dimension

CONTENTS

Speed Dome Camera Instruction Manual

5/47

Fe at u re s

 Camera Specifications

z CCD Sensor : 1/4" SONY Super HAD CCD → ×22, ×30 Model

1/4" SONY EXView CCD → ×26 Model

z Zoom Magnification : × 22 Optical Zoom, × 10 Digital Zoom (Max × 220 Zoom) → ×22 Model

× 30 Optical Zoom, × 10 Digital Zoom (Max × 300 Zoom) → ×30 Model

× 26 Optical Zoom, × 12 Digital Zoom (Max × 312 Zoom) → ×26 Model

z Day & Night Function

z Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.

z Independent & Simultaneous Camera Characteristic Setup in Preset operation

 Powerful Pan/Tilt Functions

z Max. 360°/sec high speed Pan/Tilt Motion

z Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result,

time to target view is reduced dramatically and the video on the monitor is very natural to watch.

z For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy

to locate camera to desired target view. Additionally it is easy to move camera to a desired position

with zoom-proportional pan/tilt movement.

 Preset, Pattern, Swing, Group, Privacy Mask and More…

z MAX. 127 Presets are assignable and characteristics of each preset can be set up independently,

such as White Balance, Auto Exposure, Label, Digital Outputs and so on.

z Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two

preset positions with designated speed.

z Max. 4 of Patterns can be recorded and played back. This enables to move camera to follow any

trajectory operated by joystick as closely as possible.

z Max. 8 set of Group action can be stored. This enables to move camera repetitively with

combination of Preset or Pattern or Swing. A Group is composed of max. 20 entities of

Preset/Pattern/Swings.

z Privacy Masks are assignable, not to intrude on other’s privacy. (8 Privacy Zones)

→ The availability for Privacy Mask function should be different by models.

 PTZ(Pan/Tilt/Zoom) Control

z With RS-485 communication, max. 255 of cameras can be controlled at the same time.

z Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.

INTRODUCTION

Speed Dome Camera Instruction Manual

6/47

 OSD(On Screen Display) Menu

z OSD menu is provided to display the status of camera and to configure the functions interactively.

z The information such as Camera ID, Pan/Tilt Angle, Alarm I/O and Preset can be displayed on

screen.

 Alarm I/O Functions

z 4 alarm sensor Inputs and 2 alarm Output relays are available.

z To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo

coupler and the relay is used for alarm output.

z The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.

Meanwhile, the maximum load of relay contact is AC 250V, 3A or DC 28V, 3A.

z If an external sensor is activated, camera can be set to move to the corresponding Preset position.

Meanwhile, the output relay can be matched to some specific Preset positions to do counteractions

such as turning on the light or sound the alarm.

 Reserved Presets for Special Purpose

z Most camera characteristics can be set up easily and directly with reserved preset, not entering

into OSD menu. For more information, refer to “Reserved Preset” in this manual.

 Easy Installation and Perfect Outdoor Environment Compatibility

z Fans and heaters are built-in in camera for cold and hot temperature environment. Also idealistic

mechanical design protects camera from water and dust. (IP 66)

z It is easy to install and maintain camera with terminal for cable connection in brackets.

INTRODUCTION

Speed Dome Camera Instruction Manual

7/47

Product & Accessories

 Product & Accessories

z Main Body * z Main Body (Sun-Shield) * z Dome Cover

z Wall mount bracket ** z Ceiling Mount Bracket ** z Screws

 Options

z Pole Mount Adapter z Cornor Mount Adapter

INTRODUCTION

Speed Dome Camera Instruction Manual

8/47

Parts Name & Functions

Main Body Cable

DIP Switch

Lockup Screw

Drop Prevention

Spring

Cabling Terminal Bloc

Fuse

Main Body Connector

Mold Line

z Main Body z Mount Bracket

z Dome Cover Do not detach protection vinyl from dome cover before finishing all

installation process to protect dome cover from scratches or dust.

z DIP Switch Sets up camera ID and protocol.

z Main Body Cable

Main Body Connector

Enables signals and power to come and go between main body and

mount bracket.

z Drop Prevention Spring

This part keeps the camera from dropping during installation and

maintenance. After install the Bracket, please, hang the spring to the

drop prevention hook of main body as shown in picture for further

tasks.

z Lockup Screw After assembling main body to bracket, screw main body to bracket to

protect them from separation by vibration and so on.

z Fuse If the fuse is burnt to protect your came from over-current damage, the

fuse have to be replace with new one. The fuse specification is 250V 3A.

However, we recommend consulting with supplier to remove the cause

of over-current.

z Cabling Terminal Block During installation, Power, Video, Communication, Alarm I/O cables are

connected on to this cabling terminal block.

z Mold Line Mark to assemble main body to bracket.

INTRODUCTION

Speed Dome Camera Instruction Manual

9/47

DIP Switch Setup

Before you install the camera, you should set the DIP switches to configure the camera ID, communication

protocol.

ON ON

ID0

1818

PROT

ST1

2ST3

ID7

CAM ID

Communication Protocol

Camera ID

 Camera ID Setup

123456

z ID number of camera is set using binary number. The example is

shown bellow.

Pin 1 2 3 4 5 6 7 8

ID Value 1 2 4 8 16 32 64 128

ex) ID=5 on off on off off off off off

ex) ID=10 off on off on off off off off

z The range of ID is 1~255. Do not use 0 as camera ID. Facto r y

default of Camera ID is 1.

z If you want to control a certain camera, you must match the camera

ID with Cam ID setting of DVR or Controller.

INSTALLATION

Speed Dome Camera Instruction Manual

10/47

 Communication Protocol Setup

123456

 Sensor Type Setup

123456

z Select the appropriate Protocol with DIP switch combination.

Switch State

(Pin 1)

(Pin 2)

(Pin 3)

Protocol/Baud rate

OFF OFF OFF PELCO-D, 2400 bps

ON OFF OFF PELCO-D, 9600 bps

OFF ON OFF PELCO-P, 4800 bps

ON ON OFF PELCO-P, 9600 bps

Otherwise Reserved

z If you want to control using DVR or P/T controller, their protocol must

be identical to camera. Otherwise, you can not control the camera.

z If you changed camera protocol by changing DIP S/W, the change

will be effective after you reboot the camera.

z Factory default of protocol is “Pelco-D, 2400 bps”.

z If you want to use Alarm Input, the types of sensor must be selected.

The sensor types are Normal Open and Normal.

~ Normal Open Output Voltage is high state when sensor is

activated.

~ Normal Close Output Voltage is high state when sensor is not

activated.

Pin No Switch State Sensor Type

ON Sensor 1 : Normal Close Type

ST0 (Pin 4)

OFF Sensor 1 : Normal Open Type

ON Sensor 2 : Normal Close Type

ST1 (Pin 5)

OFF Sensor 2 : Normal Open Type

ON Sensor 3 : Normal Close Type

ST2 (Pin 6)

OFF Sensor 3 : Normal Open Type

ON Sensor 4 : Normal Close Type

ST3 (Pin 7)

OFF Sensor 4 : Normal Open Type

z If sensor type is not selected properly, the alarm can be activated

rever sely.

INSTALLATION

Speed Dome Camera Instruction Manual

11/47

Installation using Wall Mount Bracket

① Install Wall Mount Bracket on wall.

② Wire cables to terminal blocks on the PCB in Wall

Mount Bracket.

③ Hook up “Drop Prevention Spring” on main body

to prevent camera from unexpected drop and

connect Main Body Cable to Main Body

Connector in Wall Mount Bracket.

④ Line up the mold lines and assemble main body

to Wall Mount Bracket.

⑤ Turn main body on its axis in CW(Clockwise)

direction and, after assembling them, screw main

body to Wall Mount Bracket to protect them from

separation by vibration or others.

⑥ In case of using pipe, use the hole located on

lower side of Wall Mount Bracket to fix pipe.

INSTALLATION

Speed Dome Camera Instruction Manual

12/47

Installation using Ceiling Mount Bracket

① To pass cables to upside of ceiling, please make a

hole with 50~60mm diameter on the ceiling panel

and attach the Ceiling mount bracket on it.

② Wire cables to terminal blocks on the PCB in

Ceiling Mount Bracket.

③ Hook up “Drop Prevention Spring” on main body

to prevent camera from unexpected drop and

connect Main Body Cable to Main Body

Connector in Ceiling Mount Bracket.

④ Line up the mold lines and assemble main body

to Ceiling Mount Bracket.

INSTALLATION

Speed Dome Camera Instruction Manual

13/47

⑤ Turn main body on its axis in CW(Clockwise)

direction and, after assembling them, screw main

body to Ceiling Mount Bracket to protect them

from separation by vibration or others.

INSTALLATION

Speed Dome Camera Instruction Manual

14/47

Cabling

RS-485

BNC

PWR+

PWR-

VIDEO(+)

VIDEO(-)

RS-485+

RS-485-

RELAY1

COMMON+ SEN1 SEN2 SEN3 SEN4

Braket Terminal Block

Moinitor

Controller

/ DVR

Power

Light

Alarm Buzzer

Sensor

Output Devices

IrDA Sensor

Door Switch

RELAY2

 Power Connection

z Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the

back of main unit.

Rated Power Input Voltage Range Current Consumption

DC 12V DC 11V ~ 18V 2.5 A

AC 24V AC 17V ~ 29V 1.5 A

 Video Connection

z Connect with BNC coaxial cable.

 RS-485 Communication

z For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time,

RS-485 communication lines of them is connected in parallel as shown below.

eyboard Controller / DVR

RS-485

INSTALLATION

Speed Dome Camera Instruction Manual

15/47

 Alarm I/O Connection

z Sensor Input

Before connecting sensors, check driving voltage and output signal type of the sensor. Since output

signal types of the sensors are divided into Open Collector and Voltage Output type in general, the

cabling must be done properly after considering these typed. Also, the sensor type, i.e. “Normal Open”

or “Normal Close” in Dip switch in main body of camera must be set properly.

Signal Description

IN COM+ Connect (+) cable of electric power source for Sensors to this port as

shown in the circuit above.

IN1−, IN 2 −, I N 3 −, I n 4 − Connect output of sensors for each port as shown in the circuit above.

z Relay Output

OUT 1

AC or DC

OUT 2

AC or DC

Internal

LOAD

Maximum allowable electrical load of relay is shown bellow table.

Drive Power DC Power AC 110V Power AC220V Power

Max. Load DC 28V, 3A AC110V, 3A AC250V, 3A

IN COM+

Internal

+5V~12V

IN 1-

IN 4-

Sensor 1 Output

Sensor 4 Output

INSTALLATION 2

+ 32 hidden pages

IC Realtime ICR2200 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual