Copyright 2007 ICRealtime, Inc. Made in Korea
ICR101X:
Mini High Speed Dome Camera
Operation Manual
ICR101X: Mini High Speed Dome Camera
Mini Endless High Speed Dome Camera
1
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNI NG - Changes or modifications not expressly approved by the
manufacturer could void the userÕs authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
2
Important Safeguard
Precautions
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance
manufacturer as they may cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported
location. Improperly installed product may fall, causing serious injury to a child or
adult, and damage to the product. Use only with a mounting device recommended
by the manufacturer, or sold with the product. To insure proper mounting, follow
the manufacturer's instructions and use only mounting accessories recommended
by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated
on the marking label.
Operating
ืBefore using, make sure power supply and others are properly connected.
ืWhile operating, if any abnormal condition or malfunction is observed, stop
using the camera immediately and then contact your local dealer.
Handling
ืDo not disassemble or tamper with parts inside the camera.
ืDo not drop or subject the camera to shock and vibration as this can damage camera.
ืCare must be taken when you clean the clear dome cover. Especially, scratch
and dust will ruin your quality of camera.
Installation and Storage
ืDo not install the camera in areas of extreme temperature, which exceed the allowable range.
ืAvoid installing in humid or dusty places.
ืAvoid installing in places where radiation is present.
ืAvoid installing in places where there are strong magnetic fields and electric signals.
ืAvoid installing in places where the camera would be subject to strong vibrations.
ืNever expose the camera to rain and water.
Introduction 1
Features
Product & Accessories
Parts Name & Functions
Installation 2
DIP Switch Setup
Direct Installation on the Ceiling
Installation using Ceiling Mount Bracket
Installation using Wall Mount Bracket
Cabling
Operation
Check points before operation
Preset and Pattern Function Pre-Check
Starting OSD Menu
Reserved Preset
Preset
Swing
Pattern
Group
Other Functions
OSD Display of Main Screen
How to use OSD Menu
General Rules of Key Operation for Menu
Main Menu
Display Setup
Privacy Zone Mask Setup
Camera Setup
Motion Setup
Preset Setup
Swing Setup
Pattern Setup
Group Setup
System Initialize
Specifications
Dimension
040607
0810111213
151516161717181920
21
22222324252729313233353637
NOTICE CONTENTS
3
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Features
Camera Specifications
ืCCD Sensor : 1/4" Interline Transfer CCD
ืZoom Magnification : Ý10 Optical Zoom, Ý10 Digital Zoom (MaxÝ100 Zoom)
ืDay & Night Function
ืVarious Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
ืIndependent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
ืMax. 360ȋ/sec high speed Pan/Tilt Motion
ืUsing Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest
path. As a result, time to target view is reduced dramatically and the video on the
monitor is very natural to watch.
ืFor jog operation using a controller, since ultra slow speed 0.05ȋ/
sec can be reached,
it is very easy to locate camera to desired target view. Additionally it is easy to move
camera to a desired position with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More...
ืMAX. 127 Presets are assignable and characteristics of each preset can be set up
independently, such as White Balance, Auto Exposure, Label and so on.
ืMax. 8 set of Swing action can be stored. This enables to move camera repetitively
between two preset positions with designated speed.
ืMax. 4 of Patterns can be recorded and played back. This enables to move camera
to follow any trajectory operated by joystick as closely as possible.
ืMax. 8 set of Group action can be stored. This enables to move camera repetitively
with combination of Preset or Pattern or Swing. A Group is composed of max.
20 entities of Preset/Pattern/Swings.
ืPrivacy Masks are assignable, not to intrude on other's privacy. (4 Privacy Zones)
PTZ(Pan/Tilt/Zoom) Control
ืWith RS-485 communication, max. 255 of cameras can be controlled at the same time.
ืPelco-D or Pelco-P protocol can be selected as a control protocol in the current version
of firmware.
OSD(On Screen Display) Menu
ืOSD menu is provided to display the status of camera and to configure the
functions interactively.
ืThe information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can
be displayed on screen.
Alarm I/O Functions
ื4 alarm sensor Inputs are available.
ืTo reject external electric noise and shock perfectly, alarm sensor Input is decoupled
with photo coupler.
ืThe signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various
applications.
ืIf an external sensor is activated, camera can be set to move to the corresponding
Preset position.
Reserved Presets for Special Purpose
ืMost camera characteristics can be set up easily and directly with reserved preset,
not entering into OSD menu. For more information, refer to "Reserved Preset"
in this manual.
INTRODUCTION 1 1 INTRODUCTION
54
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Product & Accessories Parts Name & Functions
Product & Accessories
Wall Mount Bracket
Main Unit / Surface Mount Bracket
Options
Dome Cover : Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
Surface Mount Bracket : This is used to install the camera directly on the ceiling.
After separating this cover first and then attach this directly to ceiling. Camera must
be assembled at the last stage. Do not use this bracket when installing camera on
the wall with wall mount bracket or on the ceiling with ceiling mount bracket.
Lockup Screw : Fixes main unit to surface mount bracket.
Cabling Terminal Block : During installation, Power, Video, Communication, Alarm
Input cables are connected on to this cabling terminal block.
DIP Switch : Adjusts camera ID and protocols.
INTRODUCTION 1 1 INTRODUCTION
Scrwe Cap/O-Ring
PIPING SCREW CAP
BODY LOWER
BODY UPPER
WINDOW
SCREW BODY
Body Lower-Wall Mount
Tuning System View
DIP SWITCH
TERMINAL BLOCK
76
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Main Unit Surface Mount Bracket Scrwe Cap/O-Ring
Screws & Terminal Block
Dummy Cap/O-Ring Grand Cable Lock
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure
the camera ID, communication protocol.
ืID number of camera is set using binary number.
The example is shown bellow.
ืThe range of ID is 1~255. Do not use 0 as camera ID.
Factory default of Camera ID is 1.
ืIf you want to control a certain camera, you must match
the camera ID with Cam ID setting of DVR or Controller.
Camera ID Setup
Communication Protocol Setup
GReserved for Supplier
ON
ON
ADDRESS (ID)
OPTIONS
1 2 4 8 16 32 64 128
Refer to
the Manual
PAL
NTSC
ON
1 2 3 4 5 6 7 8
Communication
Protocol Camera ID
0 0000000
OFF
ON
ON
PROTOCOL
N/P
FUNC.
PIN
OFF
Pin
ID Value
ex) ID=5
ex) ID=10
ON
FUNC.
PIN
1 2 3 4
1 2 3 4 5 6 7 8
A0 A1 A2 A3 A4 A5 A6 A7
1 2 3 4 5 6 7 8
1 2 4 8 16 32 64 128
on off on off off off off off
off on off on off off off off
ืSelect the appropriate Protocol with DIP switch
combination.
ืIf you want to control using DVR or P/T controller, their
protocol must be identical to camera. Otherwise, you
can not control the camera.
ืIf you changed camera protocol by changing DIP S/W,
the change will be effective after you reboot the camera.
ืFactory default of protocol is "Pelco-D, 2400 bps".
ืSince Pin 3 ~ Pin 4 is only for supplier, DO NOT
CHANGE THESE ITS ORIGINAL STATE. If you change
one of these, proper operation can not be achieved.
GGGඖGPin 3 : PAL / NTSC system selection of Camera.
DO NOT CHANGE THIS PIN.
GGGඖGPin 4 : Factory default is ON state. This pin is used
for system firmware upgrade. DO NOT
CHANGE THIS PIN.
ON
ON
1 2 3 4
Switch State
Protocol
P0
(Pin1)
OFF
ON
OFF
ON
OFF
OFF
ON
ON
PELCO-D, 2400 bps
PELCO-D, 9600 bps
PELCO-P, 4800 bps
PELCO-P, 9600 bps
P1
(Pin2)
ON
ON
1 2 3 4 5 6 7 8
INTRODUCTION 2 2 INTRODUCTION
98
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Direct Installation on the Ceiling
ྜGWire cables to terminal block and connect
the terminal blocks to main unit.
ྙGEstablish to the direction of cables
A. When cables exist to the upside B. When cables exist to the side
ྛGScrew surface mount bracket to ceiling
with 4 screws.
ྞGDetach protection vinyl from dome cover.ྜྷGScrew main unit to surface mount
bracket with 4 lock-up screws.
INTRODUCTION 2 2 INTRODUCTION
11
10
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
1. Remove the screw cap &
o-ring of the side
2.Assemble to the upper
part like picture.
CablingInstallation using Wall Mount Bracket
GPower Connection
ืGPlease, check the voltage and current capacity of rated power carefully. Rated power
is indicated in the back of main unit.
GRS-485 Communication
ืGFor PTZ control, connect this line to keyboard and DVR. To control multiple cameras
at the same time, RS-485 communication lines of them is connected in parallel as
shown below.
ྚGScrew wall mount bracket to ceiling with
3 screws.
ྜGScrew main unit to wall mount bracket with
4 screws.
Detach protection vinyl from dome cove.
ྛGWire cables to terminals and connect the terminals
to main unit. Do not use surface mount bracket!
DC 12V DC 11V ~ 18V
0.8 A
AC 24V AC 17V ~ 29V 0.4 A
Rated Power Input Voltage Range
Current Consumption
Keyboard Controller / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-
INTRODUCTION 2 2 INTRODUCTION
1312
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Power
Red
Red
Black
White
Blue
Green
Yellow
Black
(Shield)
Black
Pink
Orange
Grey
Violet
IN COM+
IN1
IN2
IN3
IN4
PWR(+)
PWR(-)
F.G
RS-485(+)
RS-485(-)
Cabling Terminal Block
VIDEO(+)
VIDEO(-)
Controller/ DVR
Moinitor
BNC
Sensor
IrDA
Sensor
Door
Switch
Check points before operation
Preset and Pattern Function Pre-Check
GBefore power is applied, please check the cables carefully.
GThe camera ID of the controller must be identical to that of the target camera.
The camera ID can be checked by reading DIP switch of the camera.
GIf your controller supports multi-protocols, the protocol must be changed to match to that
of the camera.
GIf you changed camera protocol by changing DIP switch, the change will be effective after
you reboot the camera.
GSince the operation method can be different for each controller available, refer to the
manual for your controller if camera can not be controlled properly. The operation of this
manual is based on the standard Pelco´ Controller.
GCheck how to operate preset and pattern function with controller or DVR in advance to
operate camera function fully when using controller or DVR.
GRefer to the following table when using standard Pelco´ protocol controller.
GIf controller or DVR has no pattern button or function, use shortcut keys with preset
numbers. For more information, refer to "Reserved Preset" in this manual.
GVideo Connection
GGGGืGConnect with BNC coaxial cable.
GAlarm Input Connection
GGGGืGSensor Input
Before connecting sensors, check driving voltage and output signal type of the sensor.
Since output signal types of the sensors are divided into Open Collector and Voltage Output
type in general, the cabling must be done properly after considering these typed.
If you want to use Alarm Input, the types of sensor must be selected in OSD menu.
The sensor types are Normal Open and Normal. If sensor type is not selected properly,
the alarm can be activated reversely.
IN COM+
Internal
+5V~12V
IN 1-
IN 4-
Sensor 1 Output
+
+
-
-
+
-
Sensor 4 Output
Signal Description
IN COM+ Connect (+) ca ble of electric power source for Sensors to this port as
shown in the circuit above.
IN1 , IN2 , IN3 , IN4 Connect output of sensors for each port as shown in the circuit above.
Normal Open Output Voltage is high state when sensor is activated
Normal Close Output Voltage is high state when sensor is not activated
Go Preset
Set Preset
Run Pattern
Set Pattern
Input [Preset Number] and press [Preset] button shortly.
Input [Preset Number] and press [Preset] button for more than 2 seconds.
Input [Pattern Number] and press [Pattern] button shortly.
Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
INTRODUCTION 2 OPERATION
1514
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Preset
Swing
Starting OSD Menu
Reserved Preset
GFunction ืGBy using Swing function, you can make camera to move between 2 Preset
positions repeatedly. When swing function runs, camera moves from the
preset assigned as the 1st point to the preset assigned as the 2nd point in
CW(Clockwise) direction. Then camera moves from the preset assigned as
the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise)
direction.
GFunction ืGUsing the OSD menu, Preset, Pattern, Swing, Group and Alarm Input
function can be configured for each application.
GFunction ืGMax. 127 positions can be stored as Preset position. The Preset number
can be assigned from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up
independently for each preset. Label should be blank and "Camera Adjust"
should be set to "GLOBAL" as default. All characteristics can be set up in
OSD menu.
GDescription ืGSome Preset numbers are reserved to special functions.
GDescription ืG<Go Preset> [95] : Enters into OSD menu
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [131~134] : Runs Pattern Function 1 ~ 4
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [141~148] : Runs Swing Function 1 ~
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [151~158] : Runs Group Function 1 ~ 8
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [161~162] : Sets Relay Output 1 ~ 2 to OFF
GGGGGGGGGGGGGGGGGGGGGGGGืG<Set Preset> [161~162] : Sets Relay Output 1 ~ 2 to ON
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [170] : Sets Camera BLC Mode to OFF
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [171] : Sets Camera BLC Mode to ON
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [174] : Sets Camera Focus Mode to AUTO
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [175] : Sets Camera Focus Mode to Manual
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [176] : Sets Camera Focus Mode to SEMI-AUTO
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [177] : Sets Day & Night Mode to AUTO
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [178] : Sets Day & Night Mode to NIGHT
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [179] : Sets Day & Night Mode to DAY
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [190] : Sets OSD Display Mode to AUTO (Except Privacy Mask)
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [191] : Sets OSD Display Mode to OFF (Except Privacy Mask)
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [193] : Sets all Privacy Mask Display to OFF
GGGGGGGGGGGGGGGGGGGGGGGGืG<Go Preset> [194] : Sets all Privacy Mask Display to ON
GEnter Menu ืG<Go Preset> [95]
GSet Preset ืG<Set Preset> [1~128]
GRun Preset ืG<Go Preset> [1~128]
GDelete Preset ืGTo delete Preset, use OSD menu.
GSet Swing ืGTo set Swing, use OSD menu.
GRun Swing ืG
Method 1) <Run Pattern> [Swing NO.+10] ex) Run Swing 3 : <Run Pattern> [13]
Method 2) <Go Preset> [Swing NO.+140] ex) Run Swing 3 : <Go Preset> [143]
GDelete SwingืGTo delete Swing, use OSD menu.
1st Preset
2nd Preset
In case that the preset assigned as the 1st point is same as the preset
assigned as the 2nd point, camera turns on its axis by 360ȋ in
CW(Clockwise) direction and then it turns on its axis by 360ȋ in
CCW(Counterclockwise) direction.
Speed can be set up from 1ȋ/sec to 180ȋ/sec.
ྙ
CW Direction
ྚ CCW Direction
OPERATION OPERATION
1716
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
GroupPattern
GFunction ืGPattern Function is that a camera memorizes the path (mostly curve path)
by joystick of controller for assigned time and revives the path exactly as
it memorized. 4 Patterns are available and Maximum 1200 communication
commands can be stored in a pattern.
GFunction ืGThe group function allows running sequence of Presets, Pattern and/or
Swings. Max 8 group can be stored. Each group can have max 20
action entities which can be preset, pattern or swing. Preset speed can
be set up and the repeat number of Pattern & Swing can be set up in
Group setup. Dwell time between actions can be set up also.
GSet Pattern ืGPattern can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
ඖGPattern editing screen is displayed as bellow.
GRun Pattern ืG
Method 1) <Run Pattern> [Pattern NO.] ex) Run Pattern 2 : <Run Pattern> [2]
Method 2) <Go Preset> [Pattern NO.+130] ex) Run Pattern 2: <Go Preset> [132]
GDelete PatternืGUse OSD menu to delete a Pattern.
GSet Preset ืGUse OSD Menu to create a Group.
GRun Preset ืG
Method 1) <Run Pattern> [Group NO.+20] ex) Run Group 7 : <Run Pattern> [27]
Method 2) <Go Preset> [Group NO.++150] ex) Run Group 7 : <Go Preset> [157]
GDelete Preset ืGUse OSD Menu to delete.
EDIT PATTERN 1
[NEAR:SAVE / FAR:DELETE]
0/0/x1/N
ඖGMovement by Joystick and preset movement can be memorized in a pattern.
ඖGThe rest memory size is displayed in progress bar.
ඖGTo save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu:See the section "How to use OSD Menu".
Preset 1 Pattern 1 Swing 1
Dwell Time
Max 20 Entities
OPERATION OPERATION
1918
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
OSD Display of Main ScreenOther Functions
GPower Up Action
GGGืGThis function enables to resume the last action executed before power down. Most of
actions such as Preset, Pattern, Swing and Group are available for this function but Jog
actions are not available to resume.
GAuto Flip
GGGืGIn case that tilt angle arrives at the top of tilt orbit (90ȋ), zoom module camera keep moving
to opposite tilt direction (180ȋ) to keep tracing targets. As soon as zoom module camera
passes through the top of tilt direction(90ȋ), images should be reversed automatically and
F appears in screen. If this function is set to OFF, tilt movement range is 0 ~ 95ȋ.
GParking Action
GGGืGThis function enables to locate the camera to specific position automatically if operator
doesn˅t operate the controller for a while. The Park Time can be defined as an interval from
1 minute to 4 hours.
GAlarm Input
GGGืG4 Alarm Inputs are used. If an external sensor is activated, camera can be set to move to
corresponding preset position. It is noted that the latest alarm input is effective if multiple
sensors are activated.
GPrivacy Zone Mask
GGGืGTo protect privacy, MAX. 4 Privacy Masks can be created on the arbitrary position to hide
objects such as windows, shops or private house. With Spherical Coordinates system,
powerful Privacy Zone Mask function is possible.
GGLOBAL/ LOCAL Image Setup
GGGืGWB(White Balance) and AE(Auto Exposure) can be set up independently for each preset.
There are 2 modes, "Global" mode & "Local" mode. The Global mode means that WB or
AE can be set up totally and simultaneously for all presets in "ZOOM CAMERA SETUP"
menu. The Local mode means that WB or AE can be set up independently or separately
for each preset in each preset setup menu. Each Local WB/AE value should activate
correspondingly when camera arrives at each preset location. During jog operation, Global
WB/AE value should be applied. All Local WB/AE value do not change although Global
WB/AE value changes.
GSemiAuto Focus
GGGืGThis mode exchanges focus mode automatically between Manual Focus mode and Auto
Focus mode by operation. Manual Focus mode activates in preset operation and Auto
Focus mode activates during jog operation. With Manual mode at presets, Focus data is
memorized in each preset in advance and camera calls focus data in correspondence
with presets as soon as camera arrives at a preset. It should shorten time to get focuses.
Focus mode changes to Auto Focus mode automatically when jog operation starts.
GP/T/Z Information ืGCurrent Pan/Tilt angle in degree, zoom magnification and a
compass direction.
GCamera ID ืGCurrent Camera ID(Address).
GPreset Label ืGThe Label stored for specific Preset.
GImage Flip ืGShows that images are currently reversed by Auto Flip Function.
GAlarm Input ืGThis information shows current state of Alarm Input. If an Input
point is ON state it will show a number corresponding to each
point. If an Input point is OFF state, '-' will be displayed.
Ex) Point 2 & 3 of inputs are ON, OSD will show as below
GAction Title ืGFollowings are possible Action Titles and their meaning.
"SET PRESET xxx" When Preset xxx is stored
"PRESET xxx" When camera reach to Preset xxx
"PATTERN x" When Pattern x is in action
"SWG x/ PRESET xxx" When Swing x is in action
"UNDEFINED" When undefined function is called to run
OPERATION OPERATION
P/T/Z Information
Camera ID
Alarm Information
Action Title
Preset Label
LABEL12345
F
CAM 1
Image Flip
PRESET1
I:1-- 4
15/4/x1/N
I : -23-
2120
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Display SetupGeneral Rules of Key Operation for Menu
Main Menu
The menu items surrounded with ( ) always has its sub menu.
For all menu level, to go into sub menu, press NEAR key.
To go to up-one-level menu, press FAR key.
To move from items to item in the menu, use joystick in the Up/Down or Left/Right.
To change a value of an item, use Up/Down of the joystick in the controller.
Press NEAR key to save values and Press FAR key to cancel values.
System Information
GGGืGDisplays system information and configuration.
Display Setup
GGGืGEnable/Disable of OSD display on Main Screen.
Dome Camera Setup
GGGืGConfigure various functions of this camera.
System Initialize
GGGืGInitializes system configuration and sets all data to
factory default configuration.
Camera ID [ON/OFF]
PTZ Information [ON/OFF/AUTO]
Action Title [ON/OFF/AUTO]
Preset Label [ON/OFF/AUTO]
Alarm Input [ON/OFF/AUTO]
Compass Direction Setup
SPEED DOME CAMERA
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
EXIT
This menu defines Enable/Disable of OSD display on
Main Screen. If an item is set to be AUTO, the item is
displayed only when the value of it is changed.
Set North to assign compass direction as criteria.
Move camera and press NEAR button to save.
HOW TO USE OSD MENU HOW TO USE OSD MENU
DISPLAY SETUP
CAMERA ID ON
PTZ INFORMATION AUTO
ACTION TITLE AUTO
PRESET LABEL AUTO
ALARM INPUT AUTO
<SET NORTH DIRECTION>
<PRIVACY ZONE>
BACK
EXIT
SET NORTH DIRECTION
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL
2322
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
CAMERA SetupPRIVACY ZONE MASK Setup
Focus Mode [AUTO/MANUAL/SEMIAUTO]
Sets camera focus mode.
ඖSEMIAUTO Mode
This mode exchanges focus mode
automatically between Manual Focus
mode and Auto Focus mode. Manual
Focus mode activates in preset
operation and Auto Focus mode
activates when jog operation starts.
With Manual mode at presets, Focus
data is memorized in each preset in
advance and camera calls focus data
in correspondence with presets as
soon as camera arrives at a preset.
Digital Zoom G[ON/OFF]
Sets digital zoom function to ON/OFF.
If this is set to OFF, optical zoom
function runs but zoom function stops
at the end of optical zoom magnification.
Line Lock G[ON/OFF]
If Line lock sync is ON, video signal is
synchronized with AC power. Video can
be fluctuated after setting is changed.
White Balance Setup
Privacy Zone Area Setup
Select area in image to mask.
Mask No [1~4]
Select Mask number. If the selected mask
has already data, camera moves as it was
set. Otherwise, "UNDEFINED" will be
displayed under "Mask NO".
Display [ON/OFF]
Sets if camera makes mask shows or not
on images.
Display [CANCEL/OK]
Deletes data in the selected mask NO.
Setup the general functions of zoom camera module.
Focus Mode [AUTO/MANUAL]
In Manual mode, Red and Blue level
can be set up manually
Red Adjust [10~60]
Blue Adjust [10~60]
PRIVACY ZONE
MASK NO 1
UNDEFINED
DISPLAY OFF
CLEAR MASK CANCEL
<EDIT MASK>
BACK
EXIT
Move camera to area to mask. Then the menu to adjust
mask size will be displayed.
EDIT MASK 1
MOVE TO TARGET POSITION
[NEAR:SELECT/FAR:CANCEL]
Privacy Zone Size Adjustment
Adjust mask size. Use joystick or arrow buttons to adjust
mask size.
ඔGඖ(Left/Right) Adjusts mask width.
G(Up/Down) Adjusts mask height.
EDIT MASK 1
[ඔඖ:ADJUST MASK WIDTH]
[:ADJUST MASK HEIGHT]
[NEAR:SAVE /FAR:CANCEL]
ZOOM CAMERA SETUP
FOCUS MODE SEMIAUTO
DIGITAL ZOOM ON
LINE LOCK OFF
<WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
BACK
EXIT
HOW TO USE OSD MENU HOW TO USE OSD MENU
WB SETUP - GLOBAL
WB MODE AUTO
RED ADJUST ---
BLUE ADJUST ---
BACK
EXIT
2524
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Motion Setup
Motion Lock [ON/OFF]
If Motion Lock is set to ON, it is impossible
to set up and delete Preset, Swing,
Pattern and Group. It is possible only to
run those functions. To set up and delete
those functions, enter into OSD menu.
PowerUpAction
[ON/OFF]
Refer to "Other Functions" section.
Auto Flip [ON/OFF]
Refer to "Other Functions" section.
Jog Max Speed
[1ȋ/sec ~360ȋ/sec]
Sets maximum jog speed. Jog speed
is inversely proportional to zoom
magnification. As zoom magnification
goes up, pan/tilt speed goes down.
Jog Direction [INVERSE/NORMAL]
If you set this to 'Inverse' , the view in
the screen is moving same direction with
jog tilting. If 'Normal' is selected, the
view in the screen is moving reversely.
Freeze in Preset
[ON/OFF]
At start point of preset movement,
camera starts freezing the image of
start point. Camera keeps displaying
the image of start point during preset
movement and does not display the
images which camera gets during preset
movement. As soon as camera stops
at preset end point, camera starts
displaying live images which it gets at
preset end point.
This function availability should be
different by models.
Setup the general functions of Pan/Tilt motions.
Auto Exposure Setup
AE SETUP - GLOBAL
BACKLIGHT OFF
DAY/NIGHT AUTO1
BRIGHTNESS 25
IRIS AUTO
SHUTTER ESC
AGC NORMAL
SSNR MIDDLE
SENS-UP <AUTO>
BACK
EXIT
Backlight [ON/OFF]
Sets Backlight Compensation
Day/Night [AUTO1/AUTO2/DAY/NIGHT]
AUTO1 exchanges Day/Night mode
faster than AUTO2.
Brightness [0~100]
Adjusts brightness of images. Iris, Shutter
Speed and Gain are adjusted automatically
in correspondence with this value.
IRIS [AUTO/MANUAL(0~100)]
If Iris is set to Auto, Iris should have
highest priority in adjusting AE and Shutter
Speed should be fixed.
If Iris is set to Manual, Iris should be fixed
and Iris has lower priority in adjusting AE,
in comparison with others.
Shutter Speed
[ESC/A.Flicker/Manual
(x128~1/120000 sec)
]
If Iris is set to Manual and Shutter Speed
is set to ESC, Shutter Speed should have
highest priority. If Shutter Speed is set to
A.Flicker, to remove Flicker, Shutter
Speed should be set to 1/100 sec. for
NTSC and 1/120 for PAL.
AGC [OFF/NORMAL/HIGH]
Enhances image brightness automatically
in case that luminance level of image
signal is too low.
SSNR [OFF/LOW/MIDDLE/HIGH]
Enhances images by deducting noises
when gain level of images is too high.
SENS-UP [AUTO(2~128)/OFF]
Activates Slow Shutter function when
luminance of image (signal) is too dark.
It is possible to set up the maximum
number of frames piled up one on another
by Slow Shutter function.
MOTION SETUP
MOTION LOCK OFF
PWR UP ACTION ON
AUTO FLIP ON
JOG MAX SPEED 120/SEC
JOG DIRECTION INVERSE
FRZ IN PRESET OFF
<PARKING ACTION SETUP>
<ALARM INPUT SETUP>
BACK
EXIT
HOW TO USE OSD MENU HOW TO USE OSD MENU
2726
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
PRESET Setup
Preset Number [1~128]
If a selected preset is already defined,
camera moves to pre-defined position
and preset characteristics such as Label
and Relay Outputs show on monitor. If
a selected preset is not defined,
"UNDEFINED" shows on monitor.
Clear Preset [CANCEL/OK]
Delete current Preset data
Edit Preset Scene
Redefine current Preset scene position
(i.e. PTZ).
Edit Preset Label
Edits Label to show on monitor when
preset runs. MAX. 10 alphabets are
allowed.
CAM Adjust [GLOBAL/LOCAL]
WB
(White Balance)
and AE
(Auto Exposure)
can be set up independently for each
preset. There are 2 modes, "Global"
mode & "Local" mode. The Global mode
means that WB or AE can be set up
totally and simultaneously for all presets
in "ZOOM CAMERA SETUP" menu.
up independently or separately for each
preset in each preset setup menu. Each
Local WB/AE value should activate
correspondingly when camera arrives
at each preset location. During jog
operation, Global WB/AE value should
be applied.
All Local WB/AE value should not change
although Global WB/AE value changes.
If "Local" is selected, Menu to set WB/AE
shows on monitor.
If Park Enable is set to ON, camera runs assigned function
automatically if there is no PTZ command during assigned
"Wait Time".
Parking Action Setup
Park Enable [ON/OFF]
Wait Time [1 minute ~ 4 hour]
The time is displayed with "hh:mm:ss"
format and you can change this by 1
min unit.
Park Action [HOME/PRESET/PATTERN/SWING
/GROUP]
ඖHOME
Camera moves to home position if there
is no PTZ command during assigned
"Wait Time".
Match the Alarm sensor input to one of Preset positions. If an
external sensor is activated, camera will move to corresponding
preset position when this item is predefined.
Alarm x Type [Normal OPEN/Normal CLOSE]
Alarm x Action [NOT USED/PRESET 1~128]
Assign counteraction Preset position to
each Alarm input.
Alarm Input Setup
PARKING ACTION SETUP
PARK ENABLE OFF
WAIT TIME 00:10:00
PARK ACTION HOME
BACK
EXIT
ALARM INPUT SETUP
ALARM1 TYPE N.OPEN
ALARM2 TYPE N.OPEN
ALARM3 TYPE N.OPEN
ALARM4 TYPE N.OPEN
ALARM1 ACT NOT USED
ALARM2 ACT NOT USED
ALARM3 ACT NOT USED
ALARM4 ACT NOT USED
BACK
EXIT
PRESET SETUP
PRESET NO. 1
CLR PRESET CANCEL
<EDIT SCENE>
<EDIT LABEL> LABEL123
CAM ADJUST GLOBAL
BACK
EXIT
HOW TO USE OSD MENU HOW TO USE OSD MENU
2928
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Swing Setup
Swing Number [1~8]
Selects Swing number to edit. If a
selected Swing has not defined,
"NOT USED" is displayed in 1st Position
and 2nd Position
1st Position G[PRESET 1~128]
2nd Position Set up the 2 position for Swing function.
If a selected preset is not defined,
"UNDEFINED" will be displayed as
shown below.
Swing Speed [1ȋ/sec ~180ȋ/sec]
Sets Swing speed from 1ȋ/sec to 180ȋ/sec.
Clear Swing [CANCEL/OK]
Deletes current Swing data.
Edit Preset Scene
ྙ Using Joystick, move camera to desired position.
ྚ By pressing NEAR key, save current PTZ data.
ྛ Press FAR key to cancel.
ྙ Edits label to show on monitor when camera arrives at
presets. In Edit Label menu, a reverse rectangular is cursor.
As soon as finishing selecting alphabet, cursor moves to
the next digit.
ྚUsing Left/Right/Up/Down of joystick, move to an appropriate
character from the Character set. To choose that character,
press the NEAR key.
ྛIf you complete the Label editing, move cursor to "OK" and
press NEAR key to save completed label. To abort current
change, move cursor to "Cancel" and press NEAR key.
If you want to use blank, choose Space character (" ").
If you want to delete a character before, use back space
character (" ˥G").
Edit Preset Label
When swing function runs, camera
moves from the preset assigned as
the 1st point to the preset assigned
as the 2nd point in CW(Clockwise)
direction. Then camera moves from
the preset assigned as the 2nd point
to the preset assigned as the 1st point
in CCW(Counterclockwise) direction.
In case that the preset assigned as the
1st point is same as the preset assigned
as the 2nd point, camera turns on its axis
by 360ȋ in CW direction and then it turns
on its axis by 360ȋ in CCW direction.
HOW TO USE OSD MENU HOW TO USE OSD MENU
EDIT SCENE - PRESET 1
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
EDIT LABEL - PRESET 1
[ ]
1234567890 OK
ABCDEFGHIJ CANCEL
KLMNOPQRST
UVWXYZabcd
efghijklmn
opqrstuvwx
yz<>-/:.
Current Cursor Position
[ ]
Back Space Char.Space Char.
1234567890
ABCDEFGHIJ
KLMNOPQRST
UVWXYZabcd
efghijklmn
opqrstuvwx
yz<>-/:.
SWING SETUP
SWING NO. 1
1ST POS. NOT USED
2ND POS. NOT USED
SWING SPEED 30/SEC
CLEAR SWING CANCEL
BACK
EXIT
SWING SETUP
SWING NO. 1
1ST POS. PRESET5
2ND POS. NOT USED
UNDEFINED
3130
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
Group SetupPattern Setup
Group Number [1~8]
Selects Group number to edit.
If a selected Group number is not defined,
"UNDEFINED" will be displayed under
selected Group number.
Clear Group [CANCEL/OK]
Deletes data in current Group
Edit Group Starts editing Group.
ྙ Press Near key in "NO" list to start Group setup.
ྚ Note that MAX. 20 Functions are allowed in a Group.
Move cursor up/down and press Near key to set up.
ྛSet up Action, Dwell time and Option. Note that selected
item is displayed in reverse. Move cursor Left/Right to
select items and move cursor Up/Down to change each
value.
GGGืAction ### [NONE/PRESET/SWING/PATTERN]
GGGืDWELL [0 second ~ 4 minutes]
Sets Dwell Time between functions
GGGืOPT Option. It should be preset speed when
preset is set in Action. It should be the
number of repeat when Pattern or
Swing is selected in Action
HOW TO USE OSD MENU HOW TO USE OSD MENU
Pattern Number [1~4 ]
Selects Pattern number to edit.
If a selected pattern number is not defined,
"UNDEFINED" will be displayed under
selected pattern number.
Clear Pattern
[CANCEL/OK]
Deletes data in current pattern
Edit Pattern
Starts editing pattern.
ྙ By using Joystick, move to start position with appropriate
zoom. To start pattern recording, press NEAR key. To exit
this menu, press FAR key.
ྚ
Move camera with joystick of controller or run preset
function to memorize the path (mostly curve path) in a
selected pattern. The total memory size and the rest
memory size is displayed in the form of bar. Maximum
1200 communication commands can be stored in a pattern.
ྛ
To save data and exit, press NEAR key. To cancel
recording and delete record data, press FAR key.
PATTERN SETUP
PATTERN NO. 1
UNDEFINED
CLR PATTERN CANCEL
<EDIT PATTERN>
BACK
EXIT
Edit Pattern
Edit Pattern
EDIT PATTERN 1
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
EDIT PATTERN 1
MOVE TO START POSITION
[NEAR:START /FAR:CANCEL]
GROUP SETUP
GROUP NO. 1
UNDEFINED
CLEAR GROUP CANCEL
<EDIT GROUP>
BACK
EXIT
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
SAVE
CANCEL [NEAR:EDIT]
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
SAVE [NEAR:EDIT ACT]
CANCEL [FAR :EDIT END]
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
SAVE [ :MOVE CURSOR]
CANCEL [ :CHANGE VAL.]
33
32
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
System Initialize
Clear All Data Deletes all configuration data such as
display, camera, motion setup and so on.
Clear Display Set
Initializes Display Configuration
Clear Camera Set
Initializes Camera Configuration
Clear Motion Set
Initializes Motion Configuration
Clear Edit Data Deletes Preset Data, Swing Data,
Pattern Data and Group Data
Reboot Camera Reboots Zoom Camera module
Reboot System Reboots Speed Dome Camera
HOW TO USE OSD MENU HOW TO USE OSD MENU
Initial Configuration Table
ྜ Set up items such as Action, ###, Dwell and OPT.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
SAVE [ඔඖ:MOVE CURSOR]
CANCEL [ :CHANGE VAL.]
ྜྷAfter finishing setting up a Action, press Near key to
one-upper-level menu(Stepྚ). Move cursor Up/Down to
select Action number and repeat Step ྚ ~ Step ྜGto edit
selected Group.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
SAVE [NEAR:EDIT ACT]
CANCEL [FAR :EDIT END]
ྞAfter finishing setting up all Actions, press FAR key to exit.
Then cursor should be moved to "SAVE".
Press Near key to save data.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
SAVE
CANCEL
SYSTEM INITIALIZE
CLEAR ALL DATA NO
CLR DISPLAY SET NO
CLR CAMERA SET NO
CLR MOTION SET NO
CLR EDIT DATA NO
REBOOT CAMERA NO
REBOOT SYSTEM NO
BACK
EXIT
GDisplay Configuration
Camera ID ON
PTZ Information AUTO
Action Title AUTO
Preset Label AUTO
Alarm Input AUTO
North Direction Pan 0ȋ
Privacy Zone Undefined
Focus Mode SemiAuto
Digital Zoom ON
Line Lock OFF
White Balance AUTO
Backlight OFF
Day&Night AUTO1
Brightness 25
Iris AUTO
Shutter ESC
AGC NORMAL
SSNR MIDDLE
SENS-UP AUTO (4 Frame)
Preset 1~128 Undefined
Swing 1~8 Undefined
Pattern 1~4 Undefined
Group 1~8 Undefined
Motion Lock OFF
Power Up Action ON
Auto Flip ON
Jog Max Speed 120ȋ/sec
Jog Direction INVERSE
Freeze In Preset OFF
Park Action OFF
Alarm Action OFF
GMotion Configuration
GCamera Configuration
GUser Edit Data
3534
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
DimensionSpecifications
* Check the voltage and current capacity of rated power carefully.
Model
x
10
Video Signal System
Camera
Pan/Tilt
General
NTSC PAL
CCD
Max. Pixels
Effective Pixels
Horizontal Res.
S/N Ratio
Zoom
Focal length
Min. illumination
Day & Night
Focus
Iris
Shutter Speed
AGC
White Balance
BLC
Flickerless
SSNR
Range
Pan/Tilt Speed
Preset
Pattern
Swing
Group
Other Functions
Communication
Protocol
Privacy Zone
Alarm Input
OSD
Rated Power*
Dimension
Weight
Operating Temp.
1/4'' Interline Transfer CCD
811(H)x508(V) 410K 795(H)x596(V) 470K
768(H)x494(V) 380K 752(H)x582(V) 440K
500 TV Line(Color), 570 TV Line(B/W)
50 dB (AGC Off)
x10 Optical Zoom, x10 Digital Zoom
F1.8, f=3.8~38mm
0.7 Lux (Color) / 0. 02 Lux (B/W), 50 IRE
Auto / Day / Night(ICR)
Auto / Manual / SemiAuto
Auto / Manual
x128 ~ 1/120000 sec
Normal / High / Off
Auto / Manual(Red, Blue Gain Adjustable)
Low / Middle / High / Off
Selectable
Low / Middle / High / Off
Pan : 360ȋ(Endless)
Tilt : 180
¶ (Auto-Flip), 95¶ (Normal)
Preset : 360¶/sec
Manual : 0.05 ~ 360¶/sec (proportional to zoom)
Swing : 1~ 180¶/sec
127 Preset (Label, Camera Image Setting)
4 Pattern, 1200 commands(about 5 minute)/Pattern
8 Swing
8 Group (20 action entities per Group)
Auto Flip, Auto Parking, Power Up Action etc.
RS-485
Pelco-D, Pelco-P selectable
4 Zone
4 Input
Menu / PTZ information etc
DC Type : DC 12V / 0.8A
AC Type : AC 24V / 0.4A
Dome : 115
Housing : 147.5 x 141(H) mm
about 1 Kg
0 ~ 40
Unit (mm)
SPECIFICATIONS SPECIFICATIONS
Ø171.0
81.563.3
Ø120.0
34.5
83.5
46.0
112.6
97.5
155.6
158.2
Ø120.0
63.3 77.0 50.3
257.4
305.1
Main Unit & Surface Mount Bracket
Wall Mount Bracket
3736
Mini Endless High Speed Dome Camera
ICR101X:
High Speed Dome Camera
MEMO
Loading...