ICRealtime ICIP-PW100 User Manual

A Series HD Wi-Fi Network Camera

Quick Start Guide

Version 1.0.1

i

Welcome

Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply requirement is
subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent power off
when necessary.
Please prevent the line cord from being trampled or pressed, especially the plug, power socket and the
junction from the device.

Note: Do not connect these two power supplying sources to the device at the same time; it may
result in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Environment

Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus; otherwise it
may cause overexposure (It is not the device malfunction), which will affect the longevity of CCD or
CMOS.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and with
strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid falling into the camera in case that the internal components
are damaged.
Please do not allow rain or damp to the indoor device in case fire or lightning may occur.
Please keep the sound ventilation in case of heat accumulation.
Please pack the device with standard factory packaging or material with same quality when transporting
the device.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3. Operation and Daily Maintenance

ii

Please do not touch the heat dissipation component of the device directly in order to avoid scald.
Please do not dismantle the device; there is no component which can be fixed by users themselves in
the machine. It may cause water leakage or bad image for the device due to unprofessional dismantling.
It is recommended to use the device with thunder proof device in order to improve thunder proof effect.
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust or
dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if it is
necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with
abrasiveness, otherwise it will damage the surface coating or reduce the working performance of the
device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation
and use, please refer to the following methods to deal with once dirt is found:

Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or paper

soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth
and wipe several times if it is not clean enough.

Warning

Please use the standard accessories provided by manufacturer and make sure the device is installed
and fixed by professional engineers.

Please prevent the device surface from the radiation of laser beam when using laser beam device.
Please do not provide two or more power supply modes for the device, otherwise it may cause damage

to the device.

Statement

Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded content will be
added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurred when using the device.
Please contact the customer service for the latest procedure and supplementary documentation.
There may be deviation between the actual value of some data and the value provided in the manual
due to the reasons such as the real environment is not stable and so on. Please refer to the company’s
final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the manual.

iii

Accessory Name

Amount

Network Camera Unit

1

Quick Start Guide

1

Installation Accessories Bag

1

Installation Pedestal

1
CD

1

Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

iv

Table of Contents

1 Structure ...................................................................................................................................... 1

1.1 Structure Info ................................................................................................................. 1

1.2 Framework and Dimension ......................................................................................... 2

2 Device Installation ...................................................................................................................... 4

2.1 Installation Steps .......................................................................................................... 4

3 Device Configuration.................................................................................................................. 5

3.1 Device Configuration Steps ........................................................................................ 5

3.2 Restore Factory Default Setup Introduction ............................................................. 8

4 Network Configuration ............................................................................................................... 9

4.1 Modify IP Address ........................................................................................................ 9

4.2 Login WEB Interface .................................................................................................. 10

1

SN

Name

1

Reset/WPS button (For reset, long press for 8 seconds; for WPS,
one quick press)

2

SD card slot

3

Network port

4

Power port

5

Indicator light

1 Structure

1.1 Structure Info

You can refer to the following figure for structure information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

Sheet 1-1

Please refer to the following sheet for more details about indicator light.