ICRealtime ICIP-MP3108-IR User Manual

IR Intelligent Speed Dome

Installation Manual

Version 1.0.0

Table of Contents

1 INSTALLATION PREPARATION ........................................................................ 1

1.1 Basic Requirement ................................................................................................................................ 1

1.2 Installation Check .................................................................................................................................. 1

1.3 Cable Preparation .................................................................................................................................. 1

1.3.1 The Min Specification Requirements of Cable ............................................................................. 1

1.3.2 Select Power Supply Cable ............................................................................................................. 2

2 DEVICE INSTALLATION .................................................................................... 3

2.1 Check Accessories ................................................................................................................................ 3

2.2 Open Device ........................................................................................................................................... 3

2.3 DIP Switch Setup ................................................................................................................................... 4

2.3.1 DIP Switch Location and Function ................................................................................................. 4

2.3.2 DIP Switch Setup .............................................................................................................................. 4

2.3.3 Address Setup ................................................................................................................................... 4

2.3.4 Baud Rate and Parity Setup ............................................................................................................ 5

2.3.5 Terminal Matched Resistance Setup ............................................................................................. 6

2.4 Reset Button Location and Micro SD Card Slot Installation ............................................................ 8

2.4.1 Use Reset Button .............................................................................................................................. 8

2.4.2 Install Micro SD Card ....................................................................................................................... 8

2.5 Camera Cable ........................................................................................................................................ 9

2.5.1 Cable Description .............................................................................................................................. 9

2.5.2 Cable Connection ........................................................................................................................... 10

2.5.3 Alarm Cable Connection ................................................................................................................ 10

2.5.4 Connect Camera GND Cable........................................................................................................ 10

3 WALL-MOUNT INSTALLATION........................................................................ 11

3.1 Installation Component and Dimension ........................................................................................... 11

3.2 Wall-Mounted Installation Steps ........................................................................................................ 11

3.2.1 Installation Conditions .................................................................................................................... 11

3.2.2 Installation Steps ............................................................................................................................. 12

4 HANG-MOUNT INSTALLATION ....................................................................... 15

4.1 Installation Component and Dimension ........................................................................................... 15

4.2 Hang-mounted Bracket Installation Steps ....................................................................................... 15

4.2.1 Installation Conditions .................................................................................................................... 15

4.2.2 Installation Steps ............................................................................................................................. 16

5 APPENDIX Ⅰ LIGHTNING PROOF AND SURGE PROTECTION (OUTDOORS)

5.1 Lightning Protection (Indoors) ............................................................................................................ 19

6 APPENDIX Ⅱ ABOUT RS485 BUS ................................................................... 21

6.1 RS485 Bus Main Feature ................................................................................................................... 21

6.2 RS485 Bus Transmission Distance .................................................................................................. 21

6.3 The Problem in Practical Use ............................................................................................................ 21

6.4 RS485 Bus FAQ .................................................................................................................................. 22

iii

7 APPENDIX Ⅲ THE RELATIONSHIP BETWEEN AC 24V CABLE DIAMETER

AND TRANSMISSION DISTANCE .......................................................................... 23

8 APPENDIX Ⅳ THE RELATIONSHIP BETWEEN DC 12V CABLE DIAMETER

AND TRANSMISSION DISTANCE .......................................................................... 24

9 APPENDIX Ⅴ WIRE GAUGE REFERENCE SHEET ........................................ 26

Welcome

Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product!

Important Safeguards and Warnings Safety Measures

1. Qualified Engineer Needed

 The installation engineer or maintenance engineer shall have corresponding CCTV system

installation certificate or maintenance qualification certificate.

 The installation engineer or maintenance engineer shall have qualification certificate for work

at height.

 The installation engineer or maintenance engineer shall have the basic knowledge and

operation technique for low-voltage cable layout and low-voltage electronic cable connection.

 Please read the installation manual carefully and keep it well for future reference,

 We are not liable for any problems caused by unauthorized modifications or attempted repair.

2. Lifting Appliance Requirement

 Please select the proper speed dome installation mode and use the lifting appliances at the

safety environment.

 The lifting appliances shall have the enough capacity to reach the installation height.

 The lifting appliances shall have safe performance.

The precaution measures include two types: Warning and Note.

 Warning: It is to alert you there is an optional risk of death or series injury!  Note: It is to alert you there is an optional risk of damage or property loss!

Warning

1. All installation and operation here should conform to your local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2. Do not connect several speed domes to one power adapter. It may result in overheat or fire if it exceeds the rated load.

3. Before you connect the cable, install or uninstall, or begin the daily maintenance work, please turn off the power and unplug the power cable.

4. Please make sure the product is secured firmly on the wall or the ceiling.

5. Please turn off the power and unplug the power cable, If there is any smoke, disgusting smell, or noise. Please contact your local retailer or customer service center for help.

6. All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

Note

1. Safety Transportation

 Heavy stress, violent vibration or water splash are not allowed during transportation, storage

and installation.

 This series product must use split type package during the transportation.

 We are not liable for any damage or problem resulting from the integrated package during

the transportation.

2. When device is malfunction

Shut down the device and disconnect the power cable immediately if there is smoke, abnormal smell or abnormal function. Please contact your local retailer ASAP.

3. Do not try to dismantle or modify the device

 There is risk of personal injury or device damage resulting from opening the shell.  Please contact your local retailer if there is internal setup or maintenance requirement.

 We are not liable for any problems caused by unauthorized modifications or attempted repair.

4. Do not allow other object falling into the device

 Please make sure there is no metal or inflammable, explosive substance in the speed dome.  The above mentioned objects in the device may result in fire, short-circuit or damage.  Please shut down the device and disconnect the power cable if there is water or liquid falling

into the camera. Please contact your local retailer ASAP.

 Please pay attention to the camera. Avoid the sea water or rain to erode the camera.

5. Handle carefully

Do not allow this series product fall down to the ground. Avoid heavy vibration.

6. Installation Environment Requirement

 This series speed dome should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

 This series product shall be away from the strong electromagnetism radiant, please keep it

away from wireless power, TV transmitter, transformer and etc.

7. Daily Maintenance

 Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning

liquid to clean the shell and then use soft cloth to make it dry.

vii

 Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result

in shell transfiguration or paint flake.

 Do not allow the plastic or rubber material to touch the shell for a long time. It may result in

paint flake.

 It is highly recommended to use the product with a lightning-proof device, which can realize

better lightning-proof effect.

viii

Regulatory Information

The regulatory information herein might vary according to the model you purchased. Some information is only applicable for the country or region where product is sold.

FCC Information

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

 This device may not cause harmful interference.  This device must accept any interference received, including interference that may cause

undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the guide, may cause harmful interference to radio communication.

 For class A device, these limits are designed to provide reasonable protection against

harmful interference in a commercial environment. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

 For class B device, these limits are designed to provide reasonable protection against

harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the

 Consult the dealer or an experienced radio/TV technician for help.

receiver is connected.

International Model

Max Distance (Ft\M)

RG59/U

750ft (229m)

RG6/U

1,000ft (305m)

RG11/U

1,500ft (457m)

1 Installation Preparation

1.1 Basic Requirement

 All installation and operation here should conform to your local electrical safety code, fire

protection regulations and other relevant regulations.

 Make sure the application scene of the camera meets the installation requirements. Please

contact dealer if you have any confusions.

 Please use the product according to the operating environment.  Please keep the original packing materials properly after opening the package. Please pack

the camera with original packing materials and send it back for maintenance if anything happens to the product.

1.2 Installation Check

 Please make sure the installation environment has enough space to install the product and

its mounting structure components.

 Please make sure the ceiling or wall can sustain 8X weight of the camera and corresponding

mounting structure components.

 Please make sure the wall is thick enough to install expansion bolts (users need to prepare

by themselves).

 It needs to pay attention that the installation height is required to be more than 6m if it is an

intelligent tracking device or laser speed dome.

1.3 Cable Preparation

Please select the min specification requirement of cable and video coaxial cable according to the transmission distance.

1.3.1 The Min Specification Requirements of Cable

 75 ohm impedance.  Full cable with copper conductor  95% knitted copper shield  RS485 communication cable, refer to appendix 2 for more details.

Note

The following table can be applied to analog speed dome and network speed dome.

Table 1-1

Note

The following table can be applied to HDAVS speed dome.

International Model

Max Transmission Distance (Ft/M)

SYV-75-3

720P（25fps/30fps）：1,640ft/500m

720P（50fps/60fps）：984ft/300m

1080P（25fps/30fps）：984ft/300m

Table 1-2

1.3.2 Select Power Supply Cable

Refer to “Appendix 3 AC 24V Cable Diameter and Transmission Distance” for AC 24V power supply device. Refer to “Appendix 4 DC 12V Cable Diameter and Transmission Distance” for DC 12V power supply device.

+ 24 hidden pages