ICRealtime ICIP-B4012VIR-I Specsheet

HD IR Fixed Network Camera Quick Start Guide

Version 1.0.2

i

Welcome

Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following saf eguard and warnings caref ully before you use this series pr oduct!
Please keep this user’s m anual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

All installation and operat i on her e s hould conform to your local e lect r i cal safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to t he r equirement in the SELV (Safety Extra Low Voltage) and t he Li m ited
power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (P ow er supply requirement is
subject to the device label) .
Please install easy-to-use device for pow er off before installing wiring, which is for emergent pow er off
when necessary.
Please prevent the line cor d from being trampled or presse d, especially the plug, power socket and the
junction from the device.

Note: Do not connect these two power supplying so urces to the device at the same tim e; it may
result in device damage!

We assume no liability or responsibility for all the fires or ele ctrical shock caused by i mproper handling
or installation.
We are not liable for any pr oble m s c aused by unauthorized mod i fic at io n or attempted repair.

2．Environment

Please don’t aim the device at s t r ong light (such as lighting, sunlight and so on) to focus; otherwise it
may cause overexposure ( It is not the device malfunction), which will affect the long evity of CCD or
CMOS.
Please transport, use an d st or e t he device within the range of allowed humidity and temperatur e.
Please don’t keep the device i n a pl ac e w hich is wet, dusty, extr emely hot , and extremely cold and with
strong electromagnetic radiation or unstab le l ighting.
Please do not allow water and ot her l iquid falling into the camer a in case that the internal co mpo nent s
are damaged.
Please do not allow rain or dam p to the indoor device in case fire or l ightning may occur.
Please keep the sound vent ilation in case of heat accu mu lation.
Please pack the device wit h standard factory packaging or m at er ial with same quality w hen t r anspor t ing
the device.
Heavy stress, violent vibration or water splash are not allowed during transportat ion, st or age and
installation.

3. Operation and Daily Maintenance

Please do not touch the heat dissipation component of the device directly in order to av oid scald.

ii

Please do not dismantle the device; there is no component which can be fixed by user s t hems elves in
the machine. It may cause water leakage or bad image for the device due to unprofessional dism antling.
It is recommended to use the device with thunder proof dev ice i n or der t o improve thunder proof effect .
The grounding holes of the product are recommend ed to be grounded to further enhance the reliability
of the camera.
Do not touch the CCD (CMOS) opt ic component directly. You can use the blower to clean the dust or
dirt on the lens surface. Please u se a dr y cloth wetted by alcohol to wipe away the dust gently if it is
necessary to clean.
Always use the dry soft clot h t o clean the device. If there is too much dust , please use the water to
dilute the mild detergent fi r st and t hen use it to clean the device. Finally use the dry cloth to clean the
device. Don’t use volatile solvent l i ke a lcohol, benzene, thinner and etc or s t r ong detergent with
abrasiveness, otherwise it will damage the surface coat in g or r educe the working performa nce of the
device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation
and use, please refer to the following methods to deal w ith once dirt is found:

Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or paper

soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth
and wipe several times if it is not clean enough.

Warning

Please use the standard accessories provided by manufacturer and make sure the device is installed
and fixed by professional engineers.

Please prevent the device sur face from the radiation of laser beam when using laser beam device.
Please do not provide two or more power supply modes for the device, otherwise it may cause damage

to the device.

Statement

Please refer to the actual pr oduct for more details; the m anual is just for reference.
The manual will be regularly upgraded according t o t he product update; the upgr aded content will be
added in the manual without pr ior announcement.
Please contact the supplie r or customer service if there is any problem occurred when usin g t he device.
Please contact the customer service for the latest pr oc edure and supplement ary documentation.
There may be deviation b et ween the actual value of some data and the value provided in t he manual
due to the reasons such as the r eal environment is not stable and so on. Please refer to the company’s
final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the manua l.

Note:

iii

Please refer to the disk for more details, check and dow nload corresponding user’s manual and tool.
Before installation, plea s e open the package and check all the components are inc lud ed.
Contact your local retailer ASAP if something is bro k en in y our package.

Accessory Name Amount

Network Camera Unit 1
Quick Start Guide 1
Installation Accessorie s Bag 1
CD 1

iv

Table of Contents

1 Device Framework ..................................................................................................................... 1

1.1 Device External Cable ................................................................................................. 1

1.2 Framework and Dimension ......................................................................................... 1

2 Device Installation ...................................................................................................................... 2

3 Network Configuration ............................................................................................................... 4

3.1 Modify IP Address ........................................................................................................ 4

3.2 Login WEB Interface .................................................................................................... 5

1

1 Device Framework

1.1 Device External Cable

Note:
The following figure is for reference only, which is used to know the function of cable port.
There are differences about cable structure betwee n di ffer ent models, please refer t o t he act ual
product for more details.
You can refer to the following fig ur e f or cable information. S ee Figure 1-1

Figure 1-1

.

1.2 Framework and Dimension

Note:
The following figures are f or r eference only, which are used to know the device dimension.
Please select the following fi gur e for reference according to t he ac t ual product.
Please refer to the following f igure for dimension informat ion. The unit is mm. See Figur e 1- 2and
Figure 1-3.

Figure 1-2

2

2 Device Installation

Important
Please make sure the installation surface can min support the 3X weight of t he camera
and the bracket.

Figure 2-1

Please see Figure 2-1.

Step 1

Stick install at io n position map to designated surface where you will install the device (wall or
ceiling).

Step 2

Dig a hole according to position of hole marked on installation map.

Step 3

Open accessories bag, take out expansion bolt and insert it i nto the hole you just dug.

Step 4

Open accessories bag, take out screws. Tighten the 4 screws to fix the device on the inst allation
surface (wall or ceiling). Y ou can move device sunshade b ack and forth. When you have fixed
the device, you must tight en scr ews on sunshade.

Step 5

Plug external wiring of the device properly.

3

Figure 2-2

Note: The location of the adjus t in g s cr ew may be different due to different models, please refer
to the figures above according to the actual product.
Please be sure to loosen the ad just i ng s cr ew w hen adjusting the device pos it i on and angle,
tighten the adjusting screw after adjustment.
The continuous rotation to ward the same direction for the camera body has to be within 3 circles.
The lower cover can’t be opened f or a long time, besides; it can’t be opened in the humid
environment in case water mist and fog problem ma y happen to the device.

Step 6

Use screwdriver (in accessories bag) to loosen adjusting screw.

Step 7

Adjust the device in all pos sib le directions, and set its monit or i ng direction.

Step 8

Use screwdriver to tighten the screws.

4

3 Network Configuration

The IP address of all the cameras i s the same when leaving fac t or y (default IP192.168.1.108), in
order to make the camera get access to the network smoothly , please plan the useable IP
segment reasonably according to the actual network environment.

3.1 Modify IP Address

IP address can be acquired and modified through quick configuration tool for the cameras which
are accessed via wired network, it needs to connect wired network to configure wireless
parameters before using wireless network cameras. In this chapter, it will introduce the approach
of modifying IP address via “Quick Configuration Tool”; also you can modify the IP address in the
network parameters of the WEB interface, please refer to the document in the disk << WEB
Operation Manual>> for more details.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same
network segment with co mp ut er I P address.
Step 1 Double click the “ConfigTools.exe” and open t he quick configuration tool.
Step 2 Double click the device to be configured, the system will pop out the “Login” dialog box.

Enter the IP address, user name, password and port number of the camera, and click

“Confirm”.
Note:
The default user name and password are admin and admin respectively, the default of port is

37777. See Figure 3-1 for more details.

5

Figure 3-1

Step 3 Mo di fy the camera IP address on the “Net” interface, click “Save” to finish modification.
See Figure 3-2 for more details.

Figure 3-2

3.2 Login WEB Interface

Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for
more details
Step 1 Ope n I E and input the modified camera I P address in the address bar.

Step 2 The login interface is shown below, please input your user name and password (Default

user name is admin and password is admin respecti vely), click “login”.

See Figure 3-3 for more details.

6

Figure 3-3

Step 3 Install controls accordin g t o the system prompt; see Figure 3-4 for the WEB main interface.
Please modify the administrator password as s oon as possible after you s uccessfully logged in.

Figure 3-4

7

Note:
 This quick start guide is for reference only. Slight difference may be found in user

interface.

 All the designs and software here are subject to change without prior written notice.
 If there is any uncertainty or controversy, pl ease r ef er t o the final explanation of us.
 Please visit our website or contact your local service engineer for more inform ation.