IC Realtime ICIPB2000S User Manual

HD IR Waterproof Fixed Network Camera User’s Manual

Version 1.0.0

Welcome

Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. This series product supports PoE too. Please note:

Do not connect these two power supplying sources to the device at the same time; it may result in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．Installation

Do not apply power to the camera before completing installation. Please install the proper power cut-off device during the installation connection. Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. Please keep it away from the electromagnetic radiation object and environment. Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into the camera. Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance work.

iii

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.

Table of Contents

1 General Introduction .................................................................................................................. 1

1.1 Overview ........................................................................................................................ 1

1.2 Features ......................................................................................................................... 1

1.3 Specifications ................................................................................................................ 2

1.3.1 Performance ........................................................................................................... 2

1.3.2 Factory Default Setup ........................................................................................... 3

2 Structure ...................................................................................................................................... 9

2.1 Multiple-function Combination Cable ........................................................................ 9

2.2 Framework and Dimension ......................................................................................... 9

3 Device Installation .................................................................................................................... 11

4 Quick Configuration Tool ......................................................................................................... 13

4.1 Overview ...................................................................................................................... 13

4.2 Operation ..................................................................................................................... 13

5 Web Operation .......................................................................................................................... 16

5.1 Network Connection ................................................................................................... 16

5.2 Login and Logout ........................................................................................................ 16

6 FAQ ............................................................................................................................................ 19

Appendix Toxic or Hazardous Materials or Elements ............................................................... 20

User

Management

 Different user rights for each group, one user belongs to one group.  The user right shall not exceed the group right.

Storage

Function

 Support central server backup function in accordance with your configuration

and setup in alarm or schedule setting

 Support record via Web and the recorded file are storage in the client-end

PC.

 Support network storage function such as FTP.

Network

Monitor

 It supports one-channel video data transmit to network terminal and then

decode. Delaying time is within 270ms (network bandwidth support needed)

 Max supports 20 connections and output bandwidth is 32Mbps. System

refuses new connection request once it exceeds the bandwidth threshold.

 Adopt the following video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

 Support web access.

Network

Management

 Realize network camera configuration and management via Ethernet.  Support device management via web or client-end.

Power

 External power adapter DC 12V.  Support PoE.

Warning！ Do not connect these two power supplying sources to the device at the same time; it may result in device damage!

Assistant

Function

 Log function  Support system resource information and running status real-time display.  Day/Night mode auto switch.  Support picture parameter setup such as electronic shutter and gain setup.  Support motion detect.  Backlight compensation: screen auto split to realize backlight compensation

to adjust the bright.

 Support video watermark function to avoid vicious video modification.  Built-in IR light. Support IR night vision.  The enclosure conforms to the IP 66 protection. Has the waterproof function.

1 General Introduction

1.1 Overview

This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device.

This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to highlight the object which is suitable for the surveillance function in the low illumination environments. The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the network and then use a network client-end. Due to its multiple functions and various uses, this series network camera is widely used in many environments such office, bank, road monitor and etc.

1.2 Features

Model Parameter

ICIP B2000S Series

System

Main Processor

TI Davinci high performance DSP

Embedded LINUX

System Resources

Support real-time network, local record, and remote operation at the same time.

User Interface

Remote operation interface such as WEB, DSS, PSS

System Status

Bit stream statistics, log, and software version.

Video Parameter

Image Sensor

1/3-inch CMOS

Pixel

1920(H)*1080(V)

Gain Control

Fixed/Auto

White Balance

Manual/Auto

Exposure Mode

Manual/Auto PAL: It ranges from 1/4 to 1/10000 NTSC: It ranges from 1/3 to 1/10000

Video Compression Standard

H264/ H.264B/MJPEG

Video Frame Rate

PAL: Main stream(1920*1080@25fps)， extra stream(352*288@25fps) NTSC: Main stream(1920*1080@30fps)， extra stream(352*240@30fps)

Video Bit Rate

H.264: 56Kbps-8192Kbps. MJPEG is adjustable and bit rate is adjustable. Support customized setup.

Video Flip

Support mirror. Support flip function.

Snapshot

Max 1f/s snapshot. File extension name is JPEG.

Privacy Mask

Supports max 4 privacy mask zones

Video Setup

Support parameter setup such as bright, contrast.

Video Information

Channel title, time title, motion detect, camera masking.

Lens

3.6mm, 6mm, 8mm. Fixed focus.

Lens Interface

M12. Lens is the default accessories

Video

Motion Detect

396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th level has the highest sensitivity) Activation event: video storage, image snapshot, log, email function and etc.

Record

and

Backup

Storage Management

Support display local storage status

Netw

ork

Wire Network

1- channel wire Ethernet port, 10/100 Base-T Ethernet

Network Protocol

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,

1.3 Specifications

1.3.1 Performance

Please refer to the following sheet for network camera performance specification.

SNMP.

Remote Operation

Monitor, system setup, file download, log information, maintenance , upgrade and etc

Restore Default Setup

Reset button

IR light

IR light 20-30M.

General Parameter

Power

DC12V power and PoE.

Power Consumption

6W MAX

Working Temperature

-10℃~+60℃

Working Humidify

10%~90%

Dimensions(mm)

70*66*160

Weight

0.5Kg（Excluding box）

Installation

Bracket installation

Setup

Item Default Setup

ICIP B2000S Series

Camera

Conditions

Brightness

Contrast

Saturation

Sharpness

Anti-flicker

Outdoor

Exposure Mode

Auto

Gain Adjust

0-50

Scene Mode

Auto

Day/night Mode

Auto

BLC

Off

Mirror

Off

Flip

Off

Video

Video bit stream

Main Stream

Bit stream type

General

Encode mode

H.264

Resolution

1080P (1920*1080)

Frame Rate （FPS）

PAL:25 NTSC:30

Bit Rate Type

CBR

Recommen ded Bit

3584-8192 Kb/S

Bit Rate

8192 Watermark

Enable

1.3.2 Factory Default Setup

Please refer to the following sheet for factory default setup information.

Setup

Item Default Setup

ICIP B2000S Series

Watermark character

DigitalCCTV

Sub Stream

Enable

Bit stream type

General

Encode mode

H.264

Resolution

PAL:CIF(352*288) NTSC:CIF(352*240)

Frame Rate （FPS）

PAL:25 NTSC:30

Bit Rate Type

CBR

Recommen ded Bit

192-1024Kb/S

Bit Rate

1024

Snapshot

Snapshot Type

General

Image Size

1080P (1920*1080)

Quality

Interval

Video Overlay

Privacy Mask

Disable

Channel Title

Enable

Time Title

Enable

Path

Snapshot Path

C:\PictureDownload

Record Path

C:\RecordDownload

Network

TCP/IP

Host Name

IPC

Ethernet Card

Wire

Mode

Static

Mac Address

Device MAC address when it is shipped out of the factory

IP Version

IPV4

IP Address

192.168.1.108

Subnet Mask

255.255.255.0

Default Gateway

192.168.1.1

Preferred DNS

8.8.8.8 Alternate

8.8.8.8

Setup

Item Default Setup

ICIP B2000S Series

DNS

Enable ARP/Ping set device IP address service

Enable

Connection

Max Connection

TCP Port

37777

UDP Port

37778

HTTP Port

RTSP Port

554

HTTPs enable

Disable

HTTPs Port

443

PPPoE Enable

Disable

Username

none

Password

N/A

DDNS

Server Type

Disable，CN99 DDNS

Server IP

none

Server Port

Domain Name

none User

none

Password

****

Update Period

10 minutes

IP Filter

Trusted sites

Disable

SMTP(Email)

SMTP Server

none

Port

Anonymity

Disable

User Name

anonymity

Password

****

Sender

none

Authenticati on (Encryption mode)

N/A

Setup

Item Default Setup

ICIP B2000S Series

Title (Subject)

IPC Message Attachment

N/A

Mail Receiver

0 seconds Email Test

Disable，interval=60 seconds

UPnP

Enable UPnP

Disable

SNMP

SNMP Port

161

Read Community

public

Write Community

private

Trap Address

N/A Trap Port

162

Bonjour Enable

Enable

Server Name

SN. It depends on the actual device.

Multicast

Multicast Address

239.255.42.42

Port

36666

QoS

Real-time Monitor

Command

Event

Video detect

Motion Detect

Enable

Disable

Anti-dither

5 seconds

Sensitivity

Record Channel

Enable

Record Delay

10 seconds Send Email

Disable

Snapshot

Disable

Video Masking

Enable

Disable

Record Channel

Enable

Record Delay

10 seconds Send Email

Disable

Snapshot

Disable

Disconnectio

Enable

Disable

Setup

Item Default Setup

ICIP B2000S Series

Record

Enable

Record Delay

10 seconds

IP Conflict Enable

Disable

Record

Enable

Relay out Delay

10 seconds

Storage

FTP

Enable FTP

Disable

Server IP

N/A

Port

Username

anonymity

Password

N/A

Remote path

Record Control

Pack Duration

8 minutes Pre-record

5 seconds

Disk Full

Overwrite

Record Mode

Auto

Record Stream

Main stream

System

General

Local Host Device No

Device manufacture SN

Language

English

Video Standard

PAL

Date and time

Date Format

Y-M-D

Time Format

24H Time Zone

GMT+08:00

System Time

Sync DST

Disable

DST Type

Week

Start Time

00:00:00 of the first Sunday of the month

End Time

00:00:00 of the second Monday of the month

NTP

Disable

NTP Server

clock.isc.org

Port

Update Period

10 minutes Auto Maintenance

Auto Reboot

Enable Each 02:00 Tuesday

Setup

Item Default Setup

ICIP B2000S Series

Auto Delete Old Files

Disable

Port Name

Function

Connection

Note

LAN

Network port

Ethernet port

Connect to standard Ethernet cable.

DC12V

Power input port

Power input port. Input DC 12V.

2 Structure

2.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See Figure 2-1.

Figure 2-1

Please refer to the following sheet for detailed information.

2.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and Figure 2-3.

Figure 2-2

Figure 2-3

3 Device Installation

Important The installation wall shall min sustain 3X weight of the bracket and camera.

Please follow the steps listed below to install the device. Please refer to Figure 3-1 and Figure 3-2 for reference.

Step 1

Paste the installation map on the surface of the wall or the ceiling.

Step 2

Dig the installation holes according to the installation map.

Figure 3-1

Step 3

Open the accessories bag and then take the expansion bolt out. Insert the expansion bolt into the installation holes.

Step 4

Take the screws from the accessories bag and then use them to secure the device on the installation surface of the wall or the ceiling. The sun shield of the device can move forward or backward. Please secure the set screw of the sun shield after you fixed the device.

Step 5

Connect the corresponding cables.

Step 6

Use the cross-head screwdriver to loosen the adjust screw.

Step 7

Turn the device in different directions to make it suitable for the monitor position.

Step 8

Use the cross-head screwdriver to fix the adjust screw firmly.

Figure 3-2

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe” icon; you can see an interface is shown as in Figure 4-1. In the device list interface, you can view device IP address, port number, subnet mask, default gateway, MAC address and etc.

Figure 4-1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.

Note:

You can set the IP address, subnet mask and gateway for the network camera and PC. Please note network camera IP address and PC IP address shall be in the same network segment if there is no router. Network camera default IP address is 192.168.1.108. If there is a router, please set the corresponding gateway and subnet mask. The factory default user name is admin and password is admin. For security reasons, please modify your password after you first login. For detailed WEB operation, please refer to the network camera Web Operation Manual in the resource CD.

Figure 4-2

Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 4-3.

Figure 4-3

If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-4. In Figure 4-4, you can view device IP address, user name, password and port. Please modify the corresponding information to login. Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface. Otherwise, you can not login the device. If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 4-4

After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.

Figure 4-5

For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.

Input your IP address here

5 Web Operation

This series network camera product supports the Web access and management via PC. Web includes several modules: monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.

 Make sure the network camera has connected to the network properly.  Please set the IP address, subnet mask and gateway of the PC and the network camera

respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.168.1.1

 Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Logout

Open IE and input network camera address in the address bar. For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address bar. See Figure 5-1.

Figure 5-1

The login interface is shown as below. See Figure 5-2. Please input your user name and password. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login.

Figure 5-2

If it is your first time to login, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download. Or you can lower the IE security level. See Figure 5-3.

Figure 5-3

After you logged in, you can see the main window. See Figure 5-4.

Figure 5-4

Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.

Bug

I can not boot up the device or operate properly.

Please click RESET button for at least five seconds to restore factory default setup.

The water leakage occurred.

The unauthorized front or rear cap remove many result in water leakage.

The glass front cap has sustained heavy push or strike. The waterproof plug of the rear cap becomes loosen.

IR video is poor.

Do not use the proper supplying power. The IR light can not turn on completely.

The object is out of the IR distance range of current device. IR-CUT does not turn to the night mode. The photosensitive chip of

the front-end can not sense the IR light.

I can not upgrade the device via network.

When network upgrade operation failed, you can use port 3800 to continue upgrade.

I can not login the client-end or the WEB.

 For Windows OS 98 or Windows ME user, if you can not install

the client-end or can not view after the installation. We recommend the win2000sp4 OS or install the client-end of the low version.

 The Active X control is blocked.  The display card version shall be dx8.1 or higher.  Network connection error occurred.  Invalid network setup.  Invalid user name or password.

I can not play the download file.

 There is no player.  There is no DX8.1 or higher.  For the MEDIA PLAYER, there shall be Div X503Bundle.exe

plugin if you play the .AVI file.

 For Windows XP user, you need to install the plugin

DivX503Bundle.exe and ffdsho-2004 1012.exe.

To guarantee setup update

After you modified the important setup, please reboot the device via the software to make sure the setup has been updated to the storage medium.

Power adapter

 The general power adapter can work ranging from 0℃ to 40 ℃.

The device may result in unstable power supply when the temperature exceeds the working temperature.

 Please replace an industry-level power adapter if you are using

in the harsh environments.

6 FAQ

Component

Name

Toxic or Hazardous Materials or Elements

Cr VI

PBB

PBDE

Circuit Board

Component

○ ○ ○ ○ ○

○

Device Case

○ ○ ○ ○ ○ ○

Wire and Cable

○ ○ ○ ○ ○ ○

Packing

Components

○ ○ ○ ○ ○

○

Accessories

○ ○ ○ ○ ○

○

Appendix Toxic or Hazardous Materials or Elements

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized to process such kind of substances or elements, please return to the corresponding local authorities to process according to your local government statutes.

Note

 This user’s manual is for reference only. Slight difference may be found in user interface.  All the designs and software here are subject to change without prior written notice.  All trademarks and registered trademarks mentioned are the properties of their respective

owners.

 If there is any uncertainty or controversy, please refer to the final explanation of us.  Please visit our website for more information.

IC Realtime ICIPB2000S User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual