
2Megapixel Vandal-Proof FULL HD IP Camera
QUICK INSTALLATION GUIDE
ELIP-470

Please read this manual carefully before installation and operation of the product.
2

DEAR CUSTOMERS!
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to all local codes.
CAUTION
TO REDUCE THE RISK OF ELECTRLC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRLC
SHOCK
DO NOT OPEN
By selecting this product, you have decided to use a professional device that guarantees highest
quality and reliability. We would like to thank you very much for your confidence and kindly ask you to
read the following instructions carefully before installation and operation in order to take full advantage
of all quality features regarding this product.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority
to operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
TRADEMARKS
All names used in this manual for hardware and software are probably registered trademarks of
respective companies.
1

PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and
to obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should only be carried out by an authorized personnel according to local
safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power
supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time.
Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
IMAGE SENSOR may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock during the
process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the IMAGE SENSOR.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including
but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or
non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to
the information herein, at any time, for the improvements of this publication and / or the corresponding
product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable
maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause
including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system
combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject,
due to violation of privacy with the result of that surveillance-camera's or video server’s picture,
including saved data, for some reason, becomes public or is used for the purpose other than
surveillance.
2

1. PRODUCT OVERVIEW
2Megapixel Vandal-Proof FULL HD IP Camera
32-bit ARM9 RISC CPU up to 432MHz, 32KB I/D-Cache, MMU
2.0 Megapixel 1/2.8" SONY progressive scan CMOS image
sensor
1952(H) x 1116(V) 2.18 Megapixel
1944(H) x 1104(V) 2.14 Megapixel
3 ~ 10.5mm Vari-focal Megapixel Lens
H.264 High profile, Motion JPEG
H.264 Up to 30fps with 1920 x 1080P
MJPEG Up to 30fps with VGA resolution
Video Streaming
Support multi stream with H.264, MJPEG
Key Features
2.0 Mega pixel 1/2.8" SONY progressive scan CMOS image sensor for excellent image quality
Vandal Proof, fire resistant and tamper resistant
Perfect tool-free 3-Axis mechanism inside
Extended IR life cycle
Dust and Moisture free (IP66 Waterproof), IK10 Certified
Dual Streaming of H.264 and M-JPEG
Up to 30 frames per second at all image resolutions
Supports image resolutions up to Full HD (1920 x 1080)
Integrated motion detection with pre- and post-alarm image / video buffering
Event-triggered FTP and email upload of still images and videos
Full Duplex Two-Way Audio Support
Digital PTZ
UPnP supported
1 Port analog video loop-out
External microphone input & speaker output connector
External sensors or external alarm devices
Supports CBR (constant bit rate) and CVBR (variable bit rate) modes
Controllable frame rate
Video access through any standard Web browser
Privacy Masking up to 8 areas
Supports IEEE 802.3af Power over Ethernet injectors, mid- and end-spans
HTTPS supported (Hyper Text Transfer Protocol Secured)
Integrated E-Mail, FTP, DDNS and DHCP client
Extensive CGI API for software integration and remote programming operations
Includes Windows based IP Installer and License-free 16 channel NVR software
Specification
3

Effect - Color, Sharpness, Mirror / V-Flip, etc.
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC / PAL
Microphone input / 1 x Line-In (Mono)
Line output / 1 x Line-Out (Mono)
Network
Security
Password protection
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
Motion detection 4 x 3 blocks
External input / Normal Open / Close Type
File upload via ftp, e-mail
Notification via email, FTP and TCP
5MB pre-alarm and post-alarm-180sec
Remote upgrade via network
ActiveX Interface (ocx (dll) + document)
DC 12V / 1.5A, PoE (Power over Ethernet) : 802.3af
1700g Appr. (Camera Only)
Power, Network Connection
-10 degree ~ 50 degree Celsius (-13F ~ 122F)
-20 degree ~ 60 degree Celsius (-13F ~ 140F)
NVR Lite (16 Channel), IP Installer (Windows only)
Network Camera, Use Manual, External Power Adaptor, Software
CD
Specifications are subject to change without prior notice to enhance performance and stability.
4

2. NAME AND FUNCTION OF EACH PART
2.1 Package Contents
2.2 Name and Function
5

- RED LED : Power On
- GREEN LED : Network connection and
Video transmission
- GREEN LED Blinking : Motion Detection
3 ~ 10.5mm Vari-focal Megapixel Lens
Control IR LED by sensing light
IR LED
Tapping Screw (4 x 30-4EA)
Machine Screw (3 x 8-3EA)
Shield Cover
3. INSTALLATION
3.1 Installation overview
- Surface Mount
6

① Paste a Drilling Template on the ceiling or wall and drill screw points which will be dome for
Tool-free 3-Axis mounting mechanism
Perfect Tri-axis!
Panning axis up to 360° degree.
Tilting axis up to 90° degree.
Rotation axis up to 360° degree.
No need to use a tool for adjustment!
All adjustments are done quick and
easy by hand!
installation.
② Fix the Surface Mounting Base by using Tapping Screws provided.
③ Fix the Flush mount Base on Surface Mounting Base.
④ Turn the camera Ass’y to the desired direction.
⑤ Turn the dome and shied cover to the camera direction.
⑥ Fix the Dome Cover Ass’y to the Flush mount Base by using Torx Screw and Torx L-Wrench.
Caution.
Please put a LED CAP on the IR LED if there is IR reflection.
3.2 3-Axis Adjustment
3.3 INSTALLATION EXAMPLE
3.3.1 Installation Example
7

LAN Switch Router Internet Remote Access
Local Access E-Mail / FTP
3.3.2 Connecting Network
1) Run IPScan Utility program in the packaged CD.
2) Click “Scan” button. Once IPScan Utility program scanned, the panel shows
every camera or video server connected on the local network.
3) The MAC address can be found on the label of the camera or video server.
4) From the cameras or video servers listed, select one and click “IP Change to assign a
new IP address.
5) Select DHCP or STATIC, then change IP address.
Default ID and password are “admin" and “1234” respectively.
8

3.3.3 Accessing the Camera or video server’s Homepage
1) After you assign IP address to your IP camera or video server and enter that camera or video server
address on the Web Browser, you will be connected to the login page of the camera or video server
as shown below.
2) Enter a ID (username) and password to access the camera or video server.
The default ID and password are “admin” and “1234”.
3) The first time you login to the camera or video server using ActiveX, you are notified that a required
ActiveX control is required. You need to allow the installation of ActiveX by clicking "Yes". It is
normal for this process to take up to 30 seconds.
For more information, see the manual of IP camera or video server in the packaged CD.
4. DIMENSION (mm)
9