IC Realtime AVS-D2110 User Manual

1 Megapixel HD AVS Camera User’s Manual

Version 1.1.0

i

Table of Contents

1 General Introduction .............................................................................................................. 1

1.1 Overview ................................................................................................................... 1

1.2 Features ................................................................................................ .................... 1

1.3 Functions .................................................................................................................. 1

1.4 Specifications ........................................................................................................... 1

2 Framework ............................................................................................................................. 3

3 Installation .............................................................................................................................. 4

4 Menu ................................................................ ....................................................................... 6

4.1 Menu List .................................................................................................................. 6

4.2 Note ........................................................................................................................... 7

Appendix Toxic or Hazardous Materials or Elements ............................................................... 8

ii

Welcome

Thank you for purchasing our HD AVS camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series HD AVS camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
The working temperature ranges from -30℃ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

7. Daily Maintenance

iv

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1

1 General Introduction

1.1 Overview

This series megapixel HD camera conforms to the HD AVS standard. It supports video signal
high-speed long distance transmission without any delay. It can be controlled by the DVR
conforming to the HD AVS.

1.2 Features

 High-performance CMOS image sensor, megapixel definition.
 HD video, coaxial cable to transmit the control signal.
 Support 75-3 coaxial cable transmission without any loss. Transmission distance is over

500m.

 Support HD and standard definition switch.
 Support 720P@25, 720P@30, 720P@50, 720P@60.
 High speed, long distance real-time transmission.
 Support OSD (on-screen display), suitable for user self-defined setup.
 Support DC12V power supplying.
 Support 3D noise reduction(denoise),excellent performance in low illumination

environment.

 IP66 compliance.
 Support ICR switch to realize surveillance both in the daytime and at night.
 Support intelligent IR function.

1.3 Functions

HD AVS Specification

HD AVS is an over-coaxial –cable HD video transmission standard. The technology renders
two HD video formats by progressive scanning.

OSD

User-friendly on-screen display for you to select the different functions.

ICR

The IR cut removal is to filter the IR light in the daytime and then auto switch to the general
fitter at night. This function allows the camera to output the high sensitivity and clear video.

Smart IR technology

The sensor controls the IR light on/off via the combination work of the hardware and software,
which realizes the automatically IR light compensation according to the environment
illumination.

1.4 Specifications

Please refer to the following sheet for specification.

2

Model
Parameter

1 Megapixel HD AVS Camera

AVS-D2110

Video Processor

1/3" 1.3 Megapixel CMOS

Video Format

PAL/NTSC

Effective Pixel

1280(H)×960(V)

Min Illumination

0.01Lux@（F1.2，AGC ON），0 Lux with IR

Electronic Shutter

4/30~1/54,000s

Video Standard

HD AVS/CVBS compliance

Video Frame Rate

1280×720@25 fps；1280×720@30 fps；
1280×720@50 fps；1280×720@60 fps

Lens Port

M12

Lens Type

3.6mm

Day/Night Switch

ICR mechanical auto switch

Video Output

1-channel BNC HD AVS high definition video output/ CVBS standard definition
video output (Can switch.)

Denoise (Noise
Reduction)

Support 3D denoise.

OSD Menu Control

Support

OSD

EXPOSURE

Global/centre/Centre weight/BLC/Front light/Distinguish

WHITE
BALANCE

AWB-GW/AWB-CCT/AWB-PRO/AWB-TEMPROAL/AWB-AI/AWB-SZ

DAY/NIGHT

Auto/B&W/Color

FUNCTION

3DNR

ADVANCED

Mirror/Language/RS485/Video format/Version/

IMAGE

Sharpness/Contrastness/Saturation/Brightness

EXIT

SAVE/CANCEL/RESET

Max IR Distance

20m

Transmission
Distance

Over 500m via 75-3 coaxial cable.

Protection Level

IP66

Working Temperature
/Humidity

-30℃~+60℃. Humidity is less than 95%(no condensation)

Power

DC 12V±10%

Power Consumption

3.5W MAX (Input: 12V 0.29A)

Dimension(mm)

Φ113.6×85.4

Weight

300g

Installation Mode

Wall mount
In-ceiling mount

3

2 Framework

Please refer to the following figures for the dimension information. The unit is mm. See Figure
2-1.

Figure 2-1

When the standard definition/high definition switch control cable is short circuit, system outputs
standard definition video. Otherwise, when the circuit is open, system outputs the high
definition video.

4

3 Installation

Important
 Before the installation, please make sure the installation surface can sustain at

least 3X weight of the bracket and the camera.

Step1

Please take the installation position map in the accessories bag, and then paste it on the
ceiling or the wall according to your monitor area requirements. Draw and then dig three holes
in the installation surface and then insert three expansion bolts in the holes. Secure these
three bolts firmly.

Step 2

Turn counter clockwise to remove the decoration ring. Please dig a “cable exit hole” in the
surface according to the installation position map if you want to draw out the cable from the top
of the installation surface. You need to draw out the cable from the cable channel side port of
the pedestal if you want to draw out the cable from the side port of the cable channel. Adjust
the device installation pedestal to the proper position and then draw the cable through the
cable exit. Line up the three screw holes in the device pedestal to the three plastic expansion
bolt holes in the installation position. Put the three self-tapping screws in the three plastic
expansion bolts firmly. Now the dome camera is secure in the installation surface. See Figure
3-1.

Figure 3-1

Step 3

Adjust the lens to get the clear monitor video. See Figure 3-2. Use crosshead screwdriver to
loosen the screw and the turn the camera body to the proper position manually. Fix the screw
again.
Important

5

Do not remove the screw. Loosen a little bit will be OK. Please secure after you completed the
setup.

Figure 3-2

Step 4

Line up the bulge of the decoration ring to the nick of the camera body and install along the tilt
installation. Push and then turn decoration ring clockwise. The installation completed after you
secure the decoration ring. You need to use the proper tool to open up the side port of the U­cable channel of the decoration ring if you want to draw out the cable from the side port of the
cable channel when you are installing the device cable. And then you can draw out the cable
from the cable channel of the pedestal. Finally you can install the decoration ring to complete
the installation. See Figure 3-3.

Figure 3-3

6

4 Menu

4.1 Menu List

The 1st Menu

The 2nd Menu

The 3rd Menu

EXPOSU
RE

AE
MODE

GLOBAL

CENTRE

CENTRE
WEIGHT

BLC

FRONT
LIGHT

DISTINGUI
SH

RETURN

WB
MODE

AWB-GW

AWB-CCT

AWB-PRO

AWB­TEMPORAL

AWB-AI

AWB-SZ

DAY
&NIGHT

AUTO

B&W

COLOR

FUNCTI
ON

3D-NR

ON/OFF

RETURN

ADVANC
ED

MIRROR

OFF/HORIZ
ONTAL/VER
TICAL/H&V

LANGUA
GE

ENGLISH

RS485

ADDRESS

1-254

BAUD RATE

2400-115200

PROTOCOL

PELCOP/PELC
OD/DH-SD

VIDEO

720P@25
/

720P@30
/

720P@50
/
720P@60）

VERSIO
N

XXXXXXXX
RETURN

IMAGE

SHARPN
ESS

DETAIL

AUTO/MANUAL

VALUE

0-15（For
manual mode
only）

7

The 1st Menu

The 2nd Menu

The 3rd Menu

EDGE

AUTO/MANUAL

VALUE

0-15（For
manual mode
only）

RETURN

CONTRA
ST

0-255

SATURA
TION

0-15

BRIGHT
NESS

70-250，
+10

RETURN

EXIT

SAVE

CANCEL

RESET

4.2 Note

Parameter

Function

3D NR

It is to reduce video noise. The larger the number is, the lower
the noise is. The details of the video may disappear if the value
here is too large.

Contrast

It is to adjust video contrast.
The larger the number is, the higher the contrast is. You can

use this function when the whole video bright is OK but the
contrast is not proper. Please note the video may become hazy
if the value is too low. If this value is too high, the dark section
may lack brightness while the bright section may over exposure.

Saturation

It is to adjust video saturation.
The larger the number, the strong the color is. This value has

no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low.

Sharpness

The value here is to adjust the edge of the video. The larger the
value is, the clear the edge is and vice versa. Please note there
is noise if the value here is too high.

Exposure

 Front light: It is to automatically enhance video brightness

by specified value when the whole video is too dark. It is to
get clear and bright video.

 Distinguish: It is the customized exposure mode. There are

total nine exposure zones and each zone has its own
specified value.

8

Appendix Toxic or Hazardous Materials or Elements

Component

Name

Toxic or Hazardous Materials or Elements

Pb

Hg

Cd

Cr VI

PBB

PBDE

Circuit Board

Component

○ ○ ○ ○ ○

○

Device

Construction

Material

○ ○ ○ ○ ○ ○

Wire and Cable

○ ○ ○ ○ ○ ○

Packing

Components

○ ○ ○ ○ ○

○

Accessories

○ ○ ○ ○ ○

○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.

Note

 This manual is for reference only. Slight difference may be found in the user

interface.

 All the designs and software here are subject to change without prior written

notice.

 All trademarks and registered trademarks mentioned are the properties of their

respective owners.

 If there is any uncertainty or controversy, please refer to the final explanation of

us.

 Please visit our website or contact your local service engineer for more

information.