ICRealtime AVS-4MD4021-IR User Manual

HDAVS Camera User’s Manual

Version 1.0.0

i

Table of Contents

1 General Introduction .................................................................................................................. 1

1.1 Overview ........................................................................................................................ 1

1.2 Features ......................................................................................................................... 1

2 Device Framework ..................................................................................................................... 2

3 Installation.................................................................................................................................... 3

4 Menu ............................................................................................................................................. 5

4.1 HAVR Settings .............................................................................................................. 5

4.2 Menu Operation ............................................................................................................ 5

Appendix Ⅰ Maintenance ................................................................................................................... 7

ii

Welcome

Thank you for purchasing our HDAVS camera!
This user’s manual is designed to be a referenc e t ool for your system.
Please read the following saf eguard and warnings carefully before you use this series product!
Please keep this user’s m anual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

• All installation and operat i on her e s hould conform to your local e lect r i c al safety codes.

• The power shall conform to t he r equirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is ra ted DC 12V or AC24V in the IEC60950-1. (Power supply requirement is
subject to the device label) .

• Please install easy-to-use device for pow er off before installing wiring, which is for emergent pow er
off when necessary.

• Please check if the power supply meets the require me nt s of working voltage of the cam er a before
operating the device (The material and length of the power supply cable will influence terminal
voltage value).

• Please prevent the line cor d from being trampled or presse d, es pecially the plug, power socket and
the junction from the device.

2．Environment

• Please don’t aim the devic e at strong light (such as lightin g, sunlight and so on) to focus.

• Please transport, use an d st or e t he device within the range of allowed humidity and temperature.

• Please do not allow water and other liquid falling into t he cam er a in case that the internal

components are damaged.

• Please keep the sound vent ilation in case of heat accu mu lat io n.

• Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

• Please pack the device wit h standard factory packaging or material with same qual it y when
transporting the device.

• It is recommended to use the device together with lightni ng pr ot ection device to enhance lightning
protection effect.

• It is recommended to GND the dev ice to enhance device reliability.

• It is advised to use qualified v ideo tr ansmission cable to improve video quality. It is recom me nded

to use RG59 coaxial cable or higher standard.

Warning

• Please use the standard accessories provided by manufacturer and mak e sure the device is
installed and fixed by prof es si onal engineers.

• Please prevent the device sur face from the radiation of laser beam when using laser be am device.

iii

• Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.

Statement

• Please refer to the actual pr oduct for more details; t he m anual is just for reference.

• The manual will be regularly upgraded according t o the product update; the upgraded content will

be added in the manual without pr ior announcement.

• Please contact the customer service for the latest pr ocedure and supplementary documentation.

• The company is not liable for any loss caused by the operation which is not followed by the manual.

• Please refer to the compa ny’s final explanation if there is any doubt or dispute.

1

1 General Introduction

1.1 Overview

This series HDAVS camera conforms to the HDAVS standard. It supports video s ign al high­speed long distance transmission without any del ay. It can be controlled by the HAVR
conforming to the HDAVS.

1.2 Features

 Adopt high performance CMOS ima ge sensor, megapixel de f inition.
 Support coaxial transm iss ion of video, audio and co nt r ol si gnal.
 For 720P series, support RG59 coaxial cable transmission wit hout any loss. The distan ce

is over 800m. For 1080P, 4M and 4K series, suppor t RG59 coaxial cable transmission
without any loss. The dist anc e i s over 500m.

 High speed, long distance real-time transmission.
 Support HDAVS HD video and analog video output.
 Support 3D noise reductio n, excellent low illuminanc e per f ormance.
 Support ICR switch to rea l ize surveillance both in the daytime and at night.
 Support OSD menu adjustment parameters.
 Support smart IR function.
 Support WDR/DWDR function.
 Support DC 12V power supply . ( Some models support DC 12V/AC 24V power supply).
 Support IP67 compliance.
 It can be applied to environments w hich requires high definitio n image, such as banking,

supermarket, teleco m, government, school, airport , fact or y, hotel, museum and etc.

2

2 Device Framework

See Figure 2-1 for the dimension.

Figure 2-1

See Figure 2-2 for the device cable ports.

Figure 2-2

3

3 Installation

Dome camera mainly use s cei li ng in s t al lat i on; installation surface inc ludes ceiling and wall.
Users can install the device with the installation position map and the screws in t he
accessories bag.

Attention:
 Please install the device i n t i m e af t er it is taken apart, which is to avoid the camera

module being e xposed to damp env i ronment for too long.

 Before the installation, please make sure the inst al l at i on surf ace is thick enough to

sustain at least 3X weight of the camera.

 For the installat ion mode of side o ut let, make sure t he dir ect i on of side outlet is in

accordance with that of the i nst al l at i on position map when sticking the installation
position map. Besides, pull the cable through the pedestal cable slot b ef or e l ocking
the screw.

Figure 3-1

4

Step 1

Unscrew the locking screw counterclockwise to release the pedestal.

Step 2

Take out the installation position map from the accessories bag, paste it on the ceiling or wall
and dig holes on the installatio n surface according to t he installation position map.

Step 3

Use tools to fix the expansion bolts into the installation holes.

Step 4

Adjust the pedestal location (pull the cable through side cable slot if it is side cable outlet).
Align the bolt fixing hole of device pedestal with the expansion bolt fixing holes of the
installation surface; insert the self-tapping screws into the expansion bolts and secure them
firmly to fix the pedestal on the installation surface (if it is top outlet, pull the cable through the
outlet hole on the installati on sur f ace after the pedestal is fixed firmly)

Step 5

Insert the enclosure into the pedestal together with the dome body, turn the locking screws
clockwise and fix them preliminarily; rotate enclosure and dome body to a proper monitoring
location; finally tighten the locking screws to fix it comp letely.

So far, you have completed device installation and cable connection, you can check monitoring
picture via back-end codin g device.

5

4 Menu

4.1 HAVR Settings

This HDAVS camera series can adjust OSD menu via coaxial control. After connected the
camera to the HDAVS series HAVR, from Main Menu->Setting->System->PTZ, you need to
select the channel number for access and set contr ol mode as HDAVS and the protocol as
ICR-SD1. Click “Save” button to save current setup. See Figure 4-1.

Figure 4-1

4.2 Menu Operation

Click the right mouse butt on and select “PTZ Control”, t hen you will see the “PTZ Set up” menu,
which is as shown in Figure 4-2 and Figure 4-3.

Figure 4-2

6

Button

Function

Adjust lens zoom and auto

Auto focus under current

Figure 4-3

See Sheet 4-1 for the details of button funct i ons .

Open menu

、

、

If there is “ ”, click the “Confirm” button in “Menu Operation” interface to go to the 2nd menu.
Click “Return” button to go back to the previous menu inter f ace.

Select menu item
Select menu value

trigger focus
Adjust lens focus

zoom rate
Lens reset

Sheet 4-1

Note:
Some of the buttons can only

be applied for the motorized
vari-focal camera.

7

Appendix Ⅰ Maintenance

Attention:
Please maintain the device according to the followin g inst r uctions in order to ensure the i m age
effect and long-term stab l e oper ation of the device.

Maintenance for lens an d mirror surface

The lens and mirror surface are covered with antireflection coating, so it may produce
hazardous substance and lead to performance reduction or scratch, dimness etc when it is
stained with dust, grease, fingerprint and so on, please refer to the following methods to deal
with once dirt is found:

Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth

or paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to
change the cloth and wipe several times if it is not clean enoug h.

Camera Body Maintena nce

Use a soft dry cloth to clean the camera body when it is dirty, in case the dirt is hard to remove,
use a clean dry cloth soaked with mild detergent and wipe gently, make it dry later. Don’t use
volatile solvent like alcohol, benzene, thinner and etc. or strong detergent with abrasiveness,
otherwise it will damage the surface coating or reduce the w orking performance of the d evice.

Maintenance for Dome Cov er

Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following met hods to deal with once dirt is found:

Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fin ger pr int
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth

or paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to
change the cloth and wipe several times if it is not clean enough.

8

Note

• This manual is for reference only. Slight difference may be found in the user

interface.

• All the designs and software here are subject to change without prior written

notice.

• All trademarks and registered trademarks mentioned are the properties of their

respective owners.

• If there is any uncertainty or controversy, please refer to the final explanation of

us.

• Please visit our website or contact your local service engineer for more

information.