IC Realtime 2 Megapixel 1080P Weather-proof IR HD-AVS Camera User Manual

2 Megapixel HD Analog IR Waterproof Fixed Camera User’s Manual

Version 1.0.0

i

Table of Contents

1 General Introduction .................................................................................................................. 1

1.1 Overview ........................................................................................................................ 1

1.2 Features ......................................................................................................................... 1

1.3 Functions ....................................................................................................................... 1

1.4 Specifications ................................................................................................................ 1

2 Framework ................................................................................................................................... 4

2.1 Dimensions .................................................................................................................... 4

2.1.1 AVS-B2200 ............................................................................................................. 4

2.1.2 AVS-B2210 ............................................................................................................. 4

3 Installation.................................................................................................................................... 5

3.1 General Fixed Camera Installation ............................................................................ 5

3.2 Mini IR Waterproof Fixed Camera Installation ......................................................... 5

4 Menu ............................................................................................................................................. 8

4.1 Menu List ....................................................................................................................... 8

4.2 Note .............................................................................................................................. 10

Appendix Toxic or Hazardous Materials or Elements ............................................................... 11

ii

Welcome

Thank you for purchasing our analog camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series analog camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
The working temperature ranges from -30℃ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

7. Daily Maintenance

iv

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1

1 General Introduction

1.1 Overview

This series megapixel analog HD camera conforms to the HD-AVS standard. It supports video
signal high-speed long distance transmission without any delay. It can be controlled by the
DVR conforming to the HD-AVS.

1.2 Features

 High-performance CMOS image sensor, megapixel definition.
 HD video, coaxial cable to transmit the control signal.
 Support 75-3 coaxial cable transmission without any loss. Transmission distance is over

300m.

 Support analog HD and standard definition switch.
 Support 1080P@25, 1080P@30, 720P@25, 720P@30, 720P@50, 720P@60.
 High speed, long distance real-time transmission.
 Support OSD (on-screen display), suitable for user self-defined setup.
 Support privacy mask, image digital zoom.
 Support DC12V power supplying.
 Support 3D noise reduction(denoise),excellent performance in low illumination

environment.

 IP66 compliance.
 Support ICR switch to realize surveillance both in the daytime and at night.
 Support intelligent IR function.

1.3 Functions

HD-AVS Specification

HD-AVS（High Definition Analog Video System） is an over-coaxial –cable analog HD video
transmission standard. The technology renders two HD video formats by progressive scanning.

OSD

User-friendly on-screen display for you to select the different functions.

ICR

The IR cut removal is to filter the IR light in the daytime and then auto switch to the general
fitter at night. This function allows the camera to output the high sensitivity and clear video.

Smart IR technology

The sensor controls the IR light on/off via the combination work of the hardware and software,
which realizes the automatically IR light compensation according to the environment
illumination.

1.4 Specifications

2

Model
Parameter

Megapixel HD Analog IR Waterproof Fixed Camera

AVS-B2200

AVS-B2210

Video Processor

1/3" 2 Megapixel CMOS

Video Format

PAL/NTSC

Effective Pixel

1920 (H) *1080 (V)

Min Illumination

0.05Lux@（F1.2,AGC ON），0 Lux with IR

Electronic Shutter

Support slow shutter. 1/3s～1/100,000s

Video Standard

HD-AVS/CVBS compliance

Video Frame Rate

1920×1080@25fps；1920×1080@30fps；1280×720@25 fps；1280×720@30
fps；1280×720@50 fps；1280×720@60 fps

Lens Port

M12

Lens Type

2.8/3.6/6/8mm optional

Day/Night Switch

ICR mechanical auto switch

Video Output

1-channel BNC analog high definition video output./ CVBS analog standard
definition video output (Can switch.)

Denoise (Noise
Reduction)

Support 2D/3D denoise.

OSD Menu Control

Support

OSD

EXPOSURE

Exposure Mode/Exposure Level/Exposure Speed/Anti Flicker/BLC/Return

WHITE
BALANCE

Auto/Manual/Day/Night/Return&Exit

DAY/NIGHT

Auto/B&W/Color/ Return&Exit

FUNCTION

2DNR/3DNR/D-zoom/Lens/ Return&Exit

ADVANCED

Cam Title/Mirror&Flip/Motion Detect/Privacy Mask/Language/COM
Setup/System Info/ Return&Exit

IMAGE

Sharpness/Brightness/Contrastness/Saturation/Sharp Suppress/ Chroma
Suppress/Gamma/Video Format/ Return&Exit

RESET

/

EXIT

/

Max IR Distance

30m

20m

Transmission
Distance

Over 300m via 75-3 coaxial cable.

Protection Level

IP66

Working Temperature
/Humidity

-30℃~+60℃. Humidity is less than 95%(no condensation)

Power

DC 12V±10%

Power Consumption

6.5W MAX
(Input: 12V 0.54A)

4.5W MAX
(Input: 12V 0.38A)

Dimension(mm)

200.2×89.1×80.4

φ65.0×154.7

Weight

450g

380g

Please refer to the following sheet for specification.

3

Installation Mode

Wall mount

4

2 Framework

2.1 Dimensions

2.1.1 AVS-B2200
Please refer to the following figures for the dimension information. The unit is mm. See Figure
2-1.

Figure 2-1

2.1.2 AVS-B2210
Please refer to the following figures for the dimension information. The unit is mm. See Figure
2-2.

Figure 2-2

When the standard definition/high definition switch control cable is short circuit, system outputs
standard definition video. Otherwise, when the circuit is open, system outputs the high
definition video.

5

3 Installation

Important
 Before the installation, please make sure the installation surface can sustain at

least 3X weight of the bracket and the camera.

3.1 General Fixed Camera Installation

This series product supports wall-mount. Please refer to the steps listed below for installation
information.

Step 1

Please dig four installation holes in the installation surface according to the four holes of the
bottom of the bracket. Insert four expansion bolts from the accessories bag into the holes and
then use four self-tapping screws to secure the bracket on the installation surface. See Figure
3-2.
If you want to install in the wood surface, please skip the first step and then use the self­tapping screws to install the bracket directly.

Figure 3-1

Step 2

Use the inner hex wrench from the accessories bag to loosen the side panel of the bracket and
two hex knobs at the bottom. Adjust the camera to the proper monitor area and then secure
the knobs of the bracket to fasten the camera.

Step 3

Connect the video output port of the device cable to the rear-end encode device such as DVR
or NVS. Then connect the power port of the device cable to the corresponding power
supplying source.

Now you have completed dome camera installation and cable connection.
You can use the rear-end device to view the monitor video.

3.2 Mini IR Waterproof Fixed Camera Installation

6

In Figure 3-2, ①Installation surface；②Bracket；③Screws；④Camera.

Step 1

Dig three holes in the installation surface of the wall or the ceiling. Insert three expansion bolts
to the three holes and then lock firmly.

Figure 3-2

Step 2

First prepare the cable according to the cable. Line up the three screw holes at the bottom of
the bracket to the three installation holes in the wall or the ceiling, and then insert three screws
to the three holes of the chassis of the bracket and fix them firmly. Now secure the bracket on
the installation surface of the wall or the ceiling.

Step 3

Adjust the camera to the proper monitor area via the three directions indicated in Figure 3-3
after you fixed the camera.

Figure 3-3

Step 4

7

Connect the device video output port to the terminal devices such as the DVR, NVS and etc.
Then connect the power cable to the device.

Now you have completed the device installation and cable connection.
You can use the terminal encode devices to view the monitor video.

8

The 1st

The 2nd

The 3rd

Exposure

Exposure
Mode

Auto

Low
Noise

Gain Max

0～100

Gain Min

0～100

Return&Exit

For the 2nd and the 3rd
menu, when you click Exit
button to exit, system
saves current setup by
default.

Low Motion
Blur

Shutter Max

 PAL: 0ms～40ms
 NTSC: 0ms～33ms

Shutter Min

 PAL: 0ms～40ms
 NTSC: 0ms～33ms

Return&Exit

Manual

Shutter

1/100000, 1/10000,
1/4000,1/2000,1/1000,1/500,
1/250,1/120,1/100,1/60,1/50,
1/30,1/25,1/15,1/12,1/10,1/8,
1/6,1/5,1/4,1/3

Customized

Gain Max

0～100

Gain Min

0～100

Return&Exit

Exp Level

0～14

Exp Speed

0～7

Anti-flicker

Outoodr/50H
Z/60HZ

 50HZ: 1/50, 1/100, 1/25,

1/10, 1/5, 1/4.

 60HZ: 1/60, 1/120, 1/30,

1/4, 1/12, 1/6.

The 50HZ and 60HZ mode
have different manual
exposure mode and there
is no low motion blur and
low noise exposure mode.

BLC

BLC

OFF/ON

WDR

0～100

HLC

0～100

The HLC is valid when auto
exposure and outdoor anti­flicker mode are both valid.

Return&Exit

White
Balance

Auto

Manual

Blue

1～100

Red

1～100

Return&Ex
it

Day

Night

Day/Night

Auto

B/W

Color

Function

2DNR

0～100

3DNR

0～100

D-Zoom

1～10

Lens

Manual/DC

Return&Ex
it

Advanced

CAM

4 Menu

4.1 Menu List

9

The 1st

The 2nd

The 3rd

Title

Mirror/Flip
Mirror

OFF/ON

Flip

OFF/ON

Return&Exit

Motion
Detect

OFF

ON

Area Sel

0～3
There are four motion detect
zones ranging from 0 to 3.
You need to set parameters
for each zone.

Area State

OFF/ON

Sensitivity

0～100

Threshold

0～100

Area Setup

Position

Size

Use direction buttons to
set position and zone size.

Default

Return&Exit

Privacy
Mask

OFF

ON

Area Sel

0～7
There are eight privacy mask
zones ranging from 0 to 7.
You need to set parameters
for each zone.

Area state

OFF/ON

Area setup

Position

Size

Use direction buttons to set
position and zone size.

Default

Return&Exit

Language

EN

COM
Setup

Address

1～254

Apply

Return&Exit

System
Info

Version

XXXXXXXXX

Return&Exit

Image

Sharpness

0～100

Brightness

0～100

Contrastne
ss

0～100
Saturation

0～100

Sharp
Suppress

0～100

Chroma
suppress

0～100

Gamma

0～5

Video
Format

1080P@25

/1080P@
30 /720P
@25 /720
P@30 /72
0P@50 /7
20P@60

OK/CANCEL

Return&Exi
t

Reset

Exit

10

Parameter

Function

Brightness

It is to adjust monitor window bright. The value ranges from 0 to

100. The default value is 50.
The larger the number is, the bright the video is. When you

input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
recommended value ranges from 40 to 60.

Contrast

It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.

The larger the number is, the higher the contrast is. You can
use this function when the whole video bright is OK but the
contrast is not proper. Please note the video may become hazy
if the value is too low. If this value is too high, the dark section
may lack brightness while the bright section may over
exposure .The recommended value ranges from 40 to 60.

Saturation

It is to adjust monitor window saturation. The value ranges from
0 to 100. The default value is 50.

The larger the number, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value
ranges from 40 to 60.

Sharpness

The value here is to adjust the edge of the video. The value
ranges from 0 to 100. The larger the value is, the clear the edge
is and vice versa. Please note there is noise if the value here is
too high. The default value is 50 and the recommended value
ranges from 40 to 60.

3DNR

It is to reduce video noise. The larger the number is, the lower
the noise is. The details of the video may disappear if the value
here is too large.

Anti-flicker

 Outdoor: In this mode, you can switch exposure mode to

get the effect under the corresponding exposure mode.

 50Hz: When the current is 50Hz, system can auto adjust

the exposure according to the environment brightness in
case there is any strip.

 60Hz: When the current is 60Hz, system can auto adjust

the exposure according to the environment brightness in
case there is any strip.

4.2 Note

11

Component

Name

Toxic or Hazardous Materials or Elements

Pb

Hg

Cd

Cr VI

PBB

PBDE

Circuit Board

Component

○ ○ ○ ○ ○

○

Device

Construction

Material

○ ○ ○ ○ ○ ○

Wire and Cable

○ ○ ○ ○ ○ ○

Packing

Components

○ ○ ○ ○ ○

○

Accessories

○ ○ ○ ○ ○

○

Appendix Toxic or Hazardous Materials or Elements

O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.

Note

 This manual is for reference only. Slight difference may be found in the user

interface.

 All the designs and software here are subject to change without prior written

notice.

 All trademarks and registered trademarks mentioned are the properties of their

respective owners.

 If there is any uncertainty or controversy, please refer to the final explanation of

us.

 Please visit our website or contact your local service engineer for more

information.